2003 Chevrolet Astro Owner's Manual - Page 115

2003 Chevrolet Astro Manual

Page 115 highlights

5. Press and hold the newly-trained HomeLink@ button and observe the indicator light. If the indicator light stays on constantly, programming is complete and your device should activate when the HomeLink@ button is pressed and released. To program the remaining two HomeLink@ buttons, begin with Step 2 under "Programming HomeLink@." Do not repeat Step 1 as this will erase all of the programmed channels. If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Steps 6 through 8 following to complete the programming of a rolling-code equipped device (most commonly, a garage door opener). 8. Return to the vehicle. Firmly press and hold the programmed HomeLink@ button for two seconds, then release. Repeat the press/hold/release sequence a second time, and depending on the brand of the garage door opener (or other rolling code device), repeat this sequence a third time to complete the programming. HomeLink@should now activate your rolling code equipped device. To program the remaining two HomeLink@ buttons, begin with Step 2 of "Programming HomeLink@." Do not repeat Step 1. Gate Operator and Canadian Programming Canadian radio-frequency laws require transmitter signals to "time out" or quit after several seconds of transmission. This may not be long enough for HomeLink@ topick up the signal during programming. Similarly, some U.S. gate operators are manufactured to "time out" in the same manner. 6. At the garage door opener receiver (motor-head unit) in the garage, locate the "Learn" or "Smart" button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 7. Firmly press and release the "Learn" or "Smart" button. The name and color of the button may vary by manufacturer. You will have 30 seconds to start Step 8. If you live in Canada, or you are having difficulty programming a gate operator by using the "Programming HomeLink@' procedures (regardlessof where you live), replace Step 3 under "Programming HomeLink@' with the following: 2-36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • 295
  • 296
  • 297
  • 298
  • 299
  • 300
  • 301
  • 302
  • 303
  • 304
  • 305
  • 306
  • 307
  • 308
  • 309
  • 310
  • 311
  • 312
  • 313
  • 314
  • 315
  • 316
  • 317
  • 318
  • 319
  • 320
  • 321
  • 322
  • 323
  • 324
  • 325
  • 326
  • 327
  • 328
  • 329
  • 330
  • 331
  • 332
  • 333
  • 334
  • 335
  • 336
  • 337
  • 338
  • 339
  • 340
  • 341
  • 342
  • 343
  • 344
  • 345
  • 346
  • 347
  • 348
  • 349
  • 350
  • 351
  • 352
  • 353
  • 354
  • 355
  • 356
  • 357
  • 358
  • 359
  • 360
  • 361
  • 362
  • 363
  • 364
  • 365
  • 366
  • 367
  • 368
  • 369
  • 370
  • 371
  • 372
  • 373
  • 374
  • 375
  • 376
  • 377
  • 378
  • 379
  • 380
  • 381
  • 382
  • 383
  • 384
  • 385
  • 386

5.
Press and hold the newly-trained HomeLink@ button
and observe the indicator light.
If
the indicator light stays on constantly,
programming is complete and your device should
activate when the HomeLink@ button
is
pressed
and released.
To program the remaining two HomeLink@ buttons,
begin with Step
2
under “Programming HomeLink@.”
Do
not
repeat
Step
1
as this will erase all of the
programmed channels.
If the indicator light blinks rapidly
for two seconds
and then turns to a constant light, continue with
Steps
6
through
8
following to complete the
programming of a rolling-code equipped device
(most commonly, a garage door opener).
6.
At the garage
door
opener
receiver (motor-head
unit) in
the
garage, locate the “Learn” or “Smart”
button. This can usually be found
where the hanging
antenna wire is attached to the motor-head unit.
7.
Firmly press and release the “Learn” or “Smart”
button. The
name and color
of
the button may
vary by manufacturer.
You
will have
30
seconds to start
Step
8.
8.
Return to the vehicle.
Firmly
press and hold
the
programmed HomeLink@
button
for
two
seconds,
then release.
Repeat
the
press/hold/release
sequence a second time, and
depending
on
the
brand of the garage
door
opener
(or
other
rolling
code device), repeat this sequence a third time
to complete the programming.
HomeLink@ should now
activate
your
rolling
code
equipped device.
To program the remaining
two
HomeLink@
buttons,
begin with
Step
2
of
“Programming
HomeLink@.”
Do
not
repeat Step
1.
Gate Operator
and
Canadian
Programming
Canadian radio-frequency laws
require
transmitter
signals to
“time out” or
quit after several
seconds
of transmission. This may
not be long
enough
for
HomeLink@
to pick up the
signal during programming.
Similarly,
some
U.S.
gate
operators
are
manufactured
to “time out” in the same
manner.
If
you live in Canada, or you
are
having
difficulty
programming a gate operator
by
using
the
“Programming HomeLink@’
procedures
(regardless
of
where you live), replace Step
3
under
“Programming
HomeLink@’
with the following:
2-36