2007 Chrysler Crossfire Owner Manual
2007 Chrysler Crossfire Manual
2007 Chrysler Crossfire manual content summary:
- 2007 Chrysler Crossfire | Owner Manual - Page 1
SECTION 1 2 3 4 5 6 7 8 9 10 INTRODUCTION TABLE OF CONTENTS PAGE ...3 1 ...7 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE UNDERSTANDING YOUR INSTRUMENT PANEL STARTING AND OPERATING ...59 3 ...111 4 ...143 5 ...193 6 ...219 7 WHAT TO DO IN - 2007 Chrysler Crossfire | Owner Manual - Page 2
- 2007 Chrysler Crossfire | Owner Manual - Page 3
INTRODUCTION CONTENTS Ⅵ Introduction ...4 Ⅵ How To Use This Manual ...4 Ⅵ Warnings And Cautions ...6 Ⅵ Vehicle Identification Number ...6 1 - 2007 Chrysler Crossfire | Owner Manual - Page 4
the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your Crossfire. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully. Following the instructions and - 2007 Chrysler Crossfire | Owner Manual - Page 5
INTRODUCTION 5 1 - 2007 Chrysler Crossfire | Owner Manual - Page 6
manual you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is located beneath the left front corner of the instrument panel, visible through the windshield. This number also appears on the Automobile - 2007 Chrysler Crossfire | Owner Manual - Page 7
13 ▫ Emergency Unlocking Feature ...14 ▫ Start Lockout ...14 Ⅵ Remote Keyless Entry ...14 ▫ To Unlock The Doors ...15 ▫ To Lock The Doors ...16 ▫ Panic Alarm ...17 ▫ To Use The Panic Alarm ...17 ▫ General Information ...17 ▫ Transmitter Battery Service ...18 Ⅵ Security Alarm System ...19 ▫ Tow-Away - 2007 Chrysler Crossfire | Owner Manual - Page 8
Shoulder Belts ...24 ▫ Seat Belts And Pregnant Women ...29 ▫ Seat Belt Extender ...29 ▫ Supplemental Restraint System (SRS) - Airbag ...30 ▫ Child Restraint ...47 Ⅵ Engine Break-In Recommendations ...55 Ⅵ Safety Tips ...55 ▫ Exhaust Gas ...55 ▫ Safety Checks You Should Make Inside The Vehicle ...56 - 2007 Chrysler Crossfire | Owner Manual - Page 9
vehicle has the key code numbers for your vehicle is located in the key fob. 2 CAUTION! An unlocked car is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle unattended. NOTE: To avoid discharging the battery system requiring - 2007 Chrysler Crossfire | Owner Manual - Page 10
be started. Turning the key in the steering lock to the ON/RUN position deactivates the start lock-out. NOTE: In case the engine cannot be started, and START and ERROR are shown in the odometer display field, the system is not operational. Contact an authorized dealer. Ignition Key Removal Turn the - 2007 Chrysler Crossfire | Owner Manual - Page 11
LOCKS The vehicle doors can be locked when the doors are closed by either manually pressing the button down at the top of the door panel, pressing and releasing the bottom portion of the central locking switch located in the console, or by pressing and releasing the Lock transmit button on the - 2007 Chrysler Crossfire | Owner Manual - Page 12
the top portion of the central locking switch located in the console, or by pressing and key in the ignition switch is in the ON/RUN position, the vehicle cannot be locked or unlocked : In case of a malfunction in the central locking system, the doors can be locked and unlocked individually. To - 2007 Chrysler Crossfire | Owner Manual - Page 13
the Central Locking System If the key in the ignition switch is in the ON/RUN position, the vehicle cannot be locked or unlocked with the remote control. If the vehicle cannot be locked or unlocked at any time with the remote control, it may be necessary to change the batteries in the remote - 2007 Chrysler Crossfire | Owner Manual - Page 14
If the parking lamps flash three times, the system is operating properly. If not, there is a problem with a switch or the system. See your authorized dealer for service. Emergency Unlocking Feature In the case of an accident, the doors unlock automatically a short time after a strong deceleration is - 2007 Chrysler Crossfire | Owner Manual - Page 15
fob, neither door is opened, the key is not inserted in the ignition switch, or the central locking switch is not activated, the vehicle will automatically lock. Press the Unlock transmit button on the key fob once to unlock driver's door, rear liftgate/decklid, fuel filler door, and center console - 2007 Chrysler Crossfire | Owner Manual - Page 16
key fob once. All turn signal lights blink three times to indicate that the vehicle is locked. If the turn signal lights do not blink, a door or located in the center console. If the vehicle cannot be locked or unlocked by pressing the transmit button, then it may be necessary to change the batteries - 2007 Chrysler Crossfire | Owner Manual - Page 17
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Panic Alarm The panic alarm unlocks the driver's door, turns on the interior lights, flashes the foglights and sounds the horn for about three minutes or until the alarm is turned off. The vehicle can be driven while in - 2007 Chrysler Crossfire | Owner Manual - Page 18
Battery Service The recommended replacement Lithium battery is Panasonic CR 2025 or equivalent. To change the batteries: • Insert the new batteries Press the battery cover (1) in the direction of the arrow. • Remove the old batteries. NOTE: Only replace the batteries in pairs. The system may have - 2007 Chrysler Crossfire | Owner Manual - Page 19
RUN position. The remote control should once again be operational. SECURITY ALARM SYSTEM The system monitors the doors, rear liftgate/decklid, hood, and ignition for unauthorized operation. The security alarm system is automatically located system has been armed, the exterior vehicle lights feature - 2007 Chrysler Crossfire | Owner Manual - Page 20
alarm remains switched off until the vehicle is locked again with the key or the remote control, at which time it is automatically reactivated. DECKLID INTERNAL EMERGENCY RELEASE ROADSTER As a security measure, a Decklid Internal Emergency Release lever is built into the decklid latching mechanism - 2007 Chrysler Crossfire | Owner Manual - Page 21
WARNING! The Trunk Internal Emergency Release will not function during the convertible top operation. POWER WINDOWS The power window switches are located in the console. To operate, turn the key in the ignition switch to the ACC or ON/RUN position. Press the switch in to the resistance point to open - 2007 Chrysler Crossfire | Owner Manual - Page 22
can also be operated by using the convertible top switch. To operate, turn the key in the ignition switch to the ON/RUN position. Press down on the rear of the convertible top switch twice to open the windows. Press down on the front of the convertible top switch twice to close the windows - 2007 Chrysler Crossfire | Owner Manual - Page 23
located features in your vehicle are the restraint systems. These include the lap/ shoulder seat belts for the driver and passenger, emergency tensioning retractors for the seat belts, and front and side airbags for the driver and passenger. If you will be carrying children too small for adult-size - 2007 Chrysler Crossfire | Owner Manual - Page 24
belt system. The belt webbing retractor will lock only during very sudden stops or impacts. This feature retractors. These tensioning retractors are located in each belt's inertia reel and become operationally ignition switch turned to the ACC or ON/RUN positions. The emergency tensioning retractors are designed - 2007 Chrysler Crossfire | Owner Manual - Page 25
an accident, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size. Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Unless the key is in the ACC or ON position, seat will not move. Sit back - 2007 Chrysler Crossfire | Owner Manual - Page 26
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap. 3. When the belt is long enough to fit, insert the - 2007 Chrysler Crossfire | Owner Manual - Page 27
your neck. The retractor will withdraw any slack in the belt. 7. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow it to retract fully. WARNING! • A belt that is buckled - 2007 Chrysler Crossfire | Owner Manual - Page 28
be replaced after an impact severe enough to fire the emergency locking retractors. If there is any question about the condition of your seat belt system, take the vehicle to an authorized dealer for an inspection. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no - 2007 Chrysler Crossfire | Owner Manual - Page 29
strong bones of the hips will take the force if there is a collision. Seat Belt Extender If a seat belt is too short even when fully extended, an authorized dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough. When it is not - 2007 Chrysler Crossfire | Owner Manual - Page 30
to have different rates of inflation that are based on collision severity and occupant size. Also, the front passenger airbag is certified to the Federal regulations that define Occupant Classification (Refer to "Occupant Classification System" in this section). Their covers are also labeled SRS - 2007 Chrysler Crossfire | Owner Manual - Page 31
• Do not attach cup holders or any other objects on or around the door. The inflating side airbag could drive objects into occupants, causing serious injury. NOTE: The passenger front airbag may not deploy even when the driver front airbag has deployed if the Occupant Classification System (refer to - 2007 Chrysler Crossfire | Owner Manual - Page 32
ride in the vehicle, move the seat as far back as possible, shut off the passenger airbag, and use the proper child restraint. See the section on "Child Restraint." You should read the instructions provided with your child restraint or belt-positioning booster seat to make sure that you are using - 2007 Chrysler Crossfire | Owner Manual - Page 33
a higher load being perceived by the OCS system which in turn could lead to the passenger airbag being turned on. Failure to follow this is always recommended to turn off the passenger front air bags using the passenger front airbags on/off switch located at the right end of the instrument panel when - 2007 Chrysler Crossfire | Owner Manual - Page 34
are not on and will not inflate. Also, the ORC turns on the AIRBAG warning light (located in the instrument cluster) and Passenger Airbag Disable (PAD) indicator light (located in the center console) for 4 seconds for a self-check when the ignition is first turned on. After the self-check, the - 2007 Chrysler Crossfire | Owner Manual - Page 35
won't have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away. WARNING! Do not put anything on or around the airbag covers or attempt to manually open them. You - 2007 Chrysler Crossfire | Owner Manual - Page 36
deflate. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system. The system may also inflate only one airbag in a reduced severity frontal collision if the seat belt on that side - 2007 Chrysler Crossfire | Owner Manual - Page 37
manufacturer's instructions for cleaning. • It is not advisable to drive your vehicle after the airbags have been deployed. If you are involved in another collision, the airbags will not be in place to protect you. How the Side Impact Airbag System Works • The side impact airbags are located in the - 2007 Chrysler Crossfire | Owner Manual - Page 38
on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers are designed to open only when the airbags are inflated. • Do not attach cup holders or any other objects - 2007 Chrysler Crossfire | Owner Manual - Page 39
coming on again. If the light does not come on at all, or if it fails to go out after the four seconds, or if it comes on thereafter, a malfunction in the system has been detected. See your authorized dealer for service. WARNING! • The door mounted side airbag deploys with considerable force. Being - 2007 Chrysler Crossfire | Owner Manual - Page 40
PAD indicator light (located in the center console) and AIRBAG warning light (located in the instrument cluster) are illuminated the airbag will be disabled. The ORC will not allow front airbag deployment in the event of a collision for occupants classified into the empty or child size categories - 2007 Chrysler Crossfire | Owner Manual - Page 41
most properly installed child restraint systems, the airbag will be disabled and the PAD indicator light will be on. However, under certain conditions even with the child restraint system has been installed properly, the PAD indicator light may not be on even though the air bag is disabled. This can - 2007 Chrysler Crossfire | Owner Manual - Page 42
threshold, the ORC will not illuminate the PAD indicator light even though the airbag is turned OFF. How the Belt Tension Sensor (BTS) Works The Belt Tension Sensor (BTS) is located at the outboard passenger lap belt anchor. The BTS creates a signal based on outboard lap belt tension. This signal - 2007 Chrysler Crossfire | Owner Manual - Page 43
When using certain types of child seats, the passenger airbag light will remain off even though the passenger front airbags are disabled. It is always recommended to turn off the passenger front air bags using the passenger front airbags on/off switch located at the right end of the instrument panel - 2007 Chrysler Crossfire | Owner Manual - Page 44
is any other occupant at that position, the supplemental restraint provided by the airbag will not be available. To turn OFF the passenger front airbag, use the on/off switch located on the instrument panel. NOTE: When the passenger airbag is turned off, the yellow airbag off light will illuminate. - 2007 Chrysler Crossfire | Owner Manual - Page 45
airbag. • The air bag will remain off until the switch is turned back to the ON position. • The switch does NOT turn off the side airbag. To Turn On the Passenger Airbag from the switch. This will turn on the passenger airbag. The Passenger Airbag Off light on the console will turn off, or will not - 2007 Chrysler Crossfire | Owner Manual - Page 46
Do not mount or locate any aftermarket equipment on or behind the knee impact blocker. • You can be injured if you are too close to either airbag cover when the airbags inflate. It is dangerous to try to repair any part of the airbag system yourself. Don't try to repair the airbag system. Be sure to - 2007 Chrysler Crossfire | Owner Manual - Page 47
collision. While the airbag Supplemental Restraint System (SRS) is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately. • The AIRBAG light does not come riding in your vehicle should be in a proper restraint for the child's size. - 2007 Chrysler Crossfire | Owner Manual - Page 48
. It is recommended for children who weigh up to about 20 lbs. (9 kg). "Convertible" child seats can be used either rearward-facing or forward-facing in the vehicle. Convertible child seats often have a higher weight limit in the rearward-facing direction than infant carriers do, so they can be used - 2007 Chrysler Crossfire | Owner Manual - Page 49
the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all . Check the label on the restraint for weight and height limits. • Carefully follow the instructions that come with the restraint. If you install the restraint - 2007 Chrysler Crossfire | Owner Manual - Page 50
are now available. Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. These are general instructions, and not all child restraint systems will be installed exactly as described here. Again - 2007 Chrysler Crossfire | Owner Manual - Page 51
when you lean in to install the child restraint. You will easily feel them if you run your finger along the intersection of the seat back and seat cushion surfaces. 2 The passenger seat tether anchorage is located on the back of the seat cushion frame. It is visible by moving the passenger - 2007 Chrysler Crossfire | Owner Manual - Page 52
according to the child restraint manufacturer's instructions. WARNING! After installing a child perceived by the OCS system which in turn could lead to the passenger airbag being turned on. turn off the passenger front air bags using the passenger front airbags on/off switch located at the right end - 2007 Chrysler Crossfire | Owner Manual - Page 53
locking and automatic locking. For child restraint installation, the retractor switches to automatic locking when ) retractor action is restored. Any seat belt system will loosen with time, so check the belt following the child restraint manufacturer's instructions. Child Restraint Tether Anchor - - 2007 Chrysler Crossfire | Owner Manual - Page 54
child seat to secure a child restraint top tether strap. Transporting Pets Deploying airbags could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in pet harnesses or pet carriers - 2007 Chrysler Crossfire | Owner Manual - Page 55
of a problem. SAFETY TIPS Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow the safety tips below. • Do not run the engine in - 2007 Chrysler Crossfire | Owner Manual - Page 56
not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.). If there is any question regarding belt or retractor condition, see your authorized dealer. Airbag Light The light should come on and remain - 2007 Chrysler Crossfire | Owner Manual - Page 57
parking for fuel, water, oil, or other fluid leaks. Also, if gasoline fumes are present, the cause should be corrected immediately. NOTE: Use of the air conditioning may cause puddles of water to form under the vehicle. 2 - 2007 Chrysler Crossfire | Owner Manual - Page 58
- 2007 Chrysler Crossfire | Owner Manual - Page 59
Operation ...62 ▫ To Lower The Top ...63 ▫ To Raise The Top ...67 ▫ Convertible Top Lamp And Audible Signal Chart ...71 Ⅵ Console Features ...72 ▫ Storage Compartments (If Equipped) ...73 ▫ Ashtray ...74 ▫ Coin Holder ...75 ▫ Power Outlet/Cigar Lighter ...75 ▫ Glove Compartment ...76 Ⅵ Cupholder (If - 2007 Chrysler Crossfire | Owner Manual - Page 60
...84 Ⅵ Interior Lights ...85 ▫ Front Map/Reading Lights ...85 ▫ Battery Saver Feature ...85 ▫ Instrument Panel Lighting ...86 ▫ Night Security Illumination ...86 Ⅵ Exterior Lights ...86 ▫ Headlights And Parking Lights ...86 ▫ Daytime Running Lights (Where Applicable) ...87 ▫ Fog Lights (If Equipped - 2007 Chrysler Crossfire | Owner Manual - Page 61
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 61 ▫ Using The Universal Transceiver ...109 ▫ Erasing Universal Transceiver Buttons ...109 ▫ Reprogramming a Single Button ...109 ▫ Security ...109 Ⅵ Umbrella Hook ...110 3 - 2007 Chrysler Crossfire | Owner Manual - Page 62
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONVERTIBLE TOP OPERATION WARNING! Before operating the switch for the convertible top, make sure that no persons can be injured by the moving parts (convertible top frame and tonneau cover). Hands must never be placed near the sport bar, convertible top - 2007 Chrysler Crossfire | Owner Manual - Page 63
can be reestablished by turning the ignition to the ON/RUN position and pushing down on the convertible top switch twice. Refer to Convertible Top Emergency Operation in the What To Do In Emergencies section of this manual. 3 CAUTION! Use caution when putting items into the storage compartment - 2007 Chrysler Crossfire | Owner Manual - Page 64
FEATURES OF YOUR VEHICLE CAUTION! To avoid possible damage to the tonneau cover and convertible top, do not allow the convertible NOTE: If the top stops during the raising or lowering procedure, start the engine and continue operation. 1. Make sure the rear cargo compartment divider is unfolded - 2007 Chrysler Crossfire | Owner Manual - Page 65
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65 NOTE: See label attached to underside of decklid. 2. Make sure the decklid is closed. CAUTION! Be sure to turn the ignition to the "ON/RUN" position before releasing the top from the windshield header. The windows will not go down if the top is - 2007 Chrysler Crossfire | Owner Manual - Page 66
66 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Once the release handle is rotated, the windows will automatically go down. 5. Push up on the convertible top latch handle to create a gap between the header and top of approximately 8 inches (200 mm). As soon as the top is free, rotate the - 2007 Chrysler Crossfire | Owner Manual - Page 67
THE FEATURES OF YOUR VEHICLE 67 NOTE: Once the top is lowered and the audible signal is heard, you can continue to push the convertible top not lower a frozen convertible top until thawed and dry. Doing so may result in damage not covered by the DaimlerChrysler Limited Warranty. 3 CAUTION! Do - 2007 Chrysler Crossfire | Owner Manual - Page 68
68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Turn the ignition key to the ON/RUN position and press down on the front of the convertible top switch. NOTE: If the top is latched to the windshield header before the rear of the top is properly latched, an audible warning will - 2007 Chrysler Crossfire | Owner Manual - Page 69
lock position and push the latch handle up to the stored position. The top is now secured in the closed position. NOTE: The convertible top switch indicator will light up and an audible warning will be heard if you start driving the vehicle without the top fully locked in the closed position - 2007 Chrysler Crossfire | Owner Manual - Page 70
70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Once the cargo compartment divider is folded forward to increase the cargo compartment capacity, the tonneau cover flaps are exposed and can be damaged by long items being put into the cargo compartment. - 2007 Chrysler Crossfire | Owner Manual - Page 71
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 Convertible Top Lamp and Audible Signal Chart Below is a 15 km/h) while trying to initiate top operation Battery voltage less than 10.6 Volts Maximum hydraulic pump run-time reached 3 Convertible top switch lamp flashes rapidly Power window motor - 2007 Chrysler Crossfire | Owner Manual - Page 72
flashers, central locking, rear defroster and towing alarm. Operating controls for the heating and air conditioning systems, power windows, power mirrors, convertible top switch (if equipped), and the automatic transmission program mode selector switch (if equipped) are also located in the console. - 2007 Chrysler Crossfire | Owner Manual - Page 73
THE FEATURES OF YOUR VEHICLE 73 Storage Compartments (If Equipped) There is a storage compartment in the console. To open the storage compartment, lift the lid with the finger depressions on either side. To close, lower the lid until the lock engages. 3 Additionally, storage pockets are located - 2007 Chrysler Crossfire | Owner Manual - Page 74
74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ashtray Lightly touch the bottom of the ashtray cover. The ashtray will open automatically. To remove the ashtray insert, pull the ashtray past the detent. Hold both sides of the insert, and pull up. To install the ashtray, place it in the frame and - 2007 Chrysler Crossfire | Owner Manual - Page 75
outlet is located in the console, next to the passenger airbag off warning light. The power outlet can accommodate a lighter or electrical accessories The lighter will operate only when the ignition switch is in the ON/ACC position. It heats up when pushed in and pops out automatically when ready - 2007 Chrysler Crossfire | Owner Manual - Page 76
to open the glove compartment. CUPHOLDER (If Equipped) The cupholder is located in the console. To open the cupholder, gently press downward on the front edge of the top panel, and then release. The cupholder will open automatically. When the cupholder is no longer needed, push forward on the top - 2007 Chrysler Crossfire | Owner Manual - Page 77
window. A two point pivot system allows for horizontal and vertical mirror adjustment. Exterior Mirrors Folding Feature All exterior mirrors are hinged another vehicle or other object. Use your inside mirror to judge the size or distance of objects seen in the convex mirror. Annoying headlight - 2007 Chrysler Crossfire | Owner Manual - Page 78
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Remote Control Outside Mirrors The mirrors can be adjusted by using the remote control located in the console. Rotate the switch to the right to select the right mirror, rotate to the left to select the left mirror. Then use - 2007 Chrysler Crossfire | Owner Manual - Page 79
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 Vanity Mirrors SEATS Your vehicle's seats can be adjusted either manually or electrically, depending on how your vehicle is equipped. WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause - 2007 Chrysler Crossfire | Owner Manual - Page 80
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: When moving the seat, be sure that there are no items in the footwell or behind the seats. Otherwise you could damage the seats. Manual Seat Adjustments (If Equipped) Seat Height (Drivers Seat Only) • Pull up on handle 3. • To lower the seat, use - 2007 Chrysler Crossfire | Owner Manual - Page 81
. • For a lower position, press release button 1 and push down on the head restraints manually. Adjust to a comfortable seating position that still allows you to reach the accelerator and brake pedal safely. The position should be as far to the rear as possible, consistent with ability to properly - 2007 Chrysler Crossfire | Owner Manual - Page 82
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Driver Eight-Way Power Seat (If Equipped) The switches to adjust the power seats are located on the outboard side of each seat. The driver's seat features eight-way power adjustment - horizontal, vertical, cushion tilt and back angle. - 2007 Chrysler Crossfire | Owner Manual - Page 83
show which setting has been selected. Heated Seats (If Equipped) This feature heats the driver and passenger seats. The controls for the heated seats are located on the instrument panel, below the radio. The heated seats setting will automatically switch from HI to LO after approximately 5 minutes. - 2007 Chrysler Crossfire | Owner Manual - Page 84
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD To open the hood, pull the release lever located inside your vehicle, below the instrument panel. WARNING! Then, reach under the hood and pull upward on the safety latch and lift the hood. To - 2007 Chrysler Crossfire | Owner Manual - Page 85
. AUTO mode also has a "fade to off" feature. When the doors are closed or locked, they gradually "fade" off. The OFF position turns off the interior lights feature. Battery Saver Feature To prevent battery drain if a door is left open or ajar, the interior lights will turn off automatically after - 2007 Chrysler Crossfire | Owner Manual - Page 86
Illumination For added security when exiting the vehicle after driving with the exterior lights on, the lights will switch on again for approximately 30 seconds after closing the last door. The lights-on timing can be changed at your authorized dealer. The headlights turn on when the switch is - 2007 Chrysler Crossfire | Owner Manual - Page 87
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Lights-On Reminder If the headlights or parking lights are left on after the ignition is turned off, a warning will sound if the driver's door is opened. Daytime Running Lights (Where Applicable) VEHICLES WITH AUTOMATIC TRANSMISSION The low beam - 2007 Chrysler Crossfire | Owner Manual - Page 88
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Standing lamps are intended for short term use when parking. If these lights are left on for a long period of time, your car's battery may drain, causing a possible starting problem. Assure that the headlamp switch is in the OFF position when - 2007 Chrysler Crossfire | Owner Manual - Page 89
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 Headlight Dimmer Switch Push the multifunction control lever toward the instrument panel to turn the headlights to high beam. Pull the lever toward you to switch to low beam. 3 - 2007 Chrysler Crossfire | Owner Manual - Page 90
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Passing Light You can signal another vehicle with your headlights by lightly pulling the a complete stop. If the wiper speed setting is normal, the wipers will change to intermittent wiping when the vehicle comes to a complete stop. Windshield Wipers And - 2007 Chrysler Crossfire | Owner Manual - Page 91
together. 3 WARNING! Mist Function Push the end of the multifunction control lever inward briefly for a single wipe without adding washer fluid. Use this feature only when the windshield is wet. Sudden loss of visibility through the windshield could lead to an accident. You might not see other - 2007 Chrysler Crossfire | Owner Manual - Page 92
FEATURES OF YOUR VEHICLE TELESCOPING STEERING COLUMN Unlock the steering column by pulling out the handle located directly below the column. The indicator light located . NOTE: If the indicator light in the instrument cluster does not go out after starting the engine, the telescoping column is not - 2007 Chrysler Crossfire | Owner Manual - Page 93
located inside the vehicle. NOTE: The TPM system can size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system - 2007 Chrysler Crossfire | Owner Manual - Page 94
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The TPM system will cause the indicator lamp in the instrument cluster to illuminate whenever the pressure in one tire falls 25% below the recommended pressure shown on the vehicle's tire label. NOTE: The pressure in your tires changes with temperature. - 2007 Chrysler Crossfire | Owner Manual - Page 95
equipment tires and wheels. TPM system pressures have been established for the tire size equipped on your vehicle. Undesirable operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do - 2007 Chrysler Crossfire | Owner Manual - Page 96
FEATURES OF YOUR VEHICLE 2. This device must accept any interference that may be received, including interference that may cause undesired operation. NOTE: Changes and modifications an override switch mounted in the center console. Once manually deployed, the spoiler will only retract by pressing - 2007 Chrysler Crossfire | Owner Manual - Page 97
also incorporates an emergency stop feature. If, for any reason . The spoiler will deploy as a safety precaution if the ESP system detects a large difference in wheel speed between the front and rear the spoiler from deploying automatically, a red warning light will illuminate in the override switch and - 2007 Chrysler Crossfire | Owner Manual - Page 98
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not drive the vehicle at speeds above 62 mph (100 km/h) if the red spoiler warning indicator is illuminated. You could have reduced vehicle stability and control. BRAKE ASSIST SYSTEM (BAS) WARNING! BAS cannot prevent the natural laws of - 2007 Chrysler Crossfire | Owner Manual - Page 99
brake pedal is released, the BAS is deactivated. turned to the ON/RUN position. They should go out with the engine running. If the BAS/ESP malfunction indicator light comes on continuously with the engine running, a malfunction has been detected in either system. If the malfunction indicator light - 2007 Chrysler Crossfire | Owner Manual - Page 100
system corrects for over/understeering of the vehicle by applying brakes to the appropriate wheel. Engine torque is also limited. The ESP warning light, located the ESP system by pressing the upper half of the ESP switch. With the ESP system switched off, the engine torque reduction feature is - 2007 Chrysler Crossfire | Owner Manual - Page 101
the drive train and is not covered by the DaimlerChrysler warranty. Synchronizing ESP If the power supply was interrupted (battery disconnected or discharged), the BAS/ESP malfunction indicator light may be illuminated with the engine running. To re-synchronize the ESP, and cancel the malfunction - 2007 Chrysler Crossfire | Owner Manual - Page 102
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL The electronic speed control automatically maintains the set speed by actively regulating the throttle setting. Any speed above approximately 20 mph (30 km/h) can be maintained with the electronic speed - 2007 Chrysler Crossfire | Owner Manual - Page 103
the accelerator. After the accelerator is released, the previously set speed will resume automatically. 3 WARNING! Leaving the electronic speed control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and - 2007 Chrysler Crossfire | Owner Manual - Page 104
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate A soft tap on the brake pedal, or normal brake pressure while slowing set speed, pull the speed control lever toward you, and then release. The resume feature can be used at any speed above 20 mph (30 km/h). NOTE: Moving the gear - 2007 Chrysler Crossfire | Owner Manual - Page 105
lighting. The transceiver triggers these devices at the push of a button. The transceiver operates off your vehicle's battery and charging system: no batteries with automatic transmission: On a downgrade or an upgrade, downshifting will occur automatically to allow the engine's braking power to - 2007 Chrysler Crossfire | Owner Manual - Page 106
battery in the hand-held transmitter before programming. If your garage door opener (located in the garage) is equipped with an antenna, make sure that the antenna is hanging straight down. 1. Turn off the engine. WARNING! Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run the - 2007 Chrysler Crossfire | Owner Manual - Page 107
THE FEATURES OF YOUR VEHICLE 107 3. Erase the factory test codes by pressing the two outside buttons. Release the buttons when the light in the , first slowly and then rapidly. Release both buttons after the indicator light changes from slow to rapid flash. If, after 90 seconds, the indicator - 2007 Chrysler Crossfire | Owner Manual - Page 108
two seconds and then turns to a constant light, continue with Programming Steps 8-10 to complete programming of a rolling code equipped device (most commonly a garage door opener). 8. At the garage door opener receiver (motor-head unit) in the garage, locate the "learn" or "smart" button. This can - 2007 Chrysler Crossfire | Owner Manual - Page 109
press and release the programmed button. Activation will now occur for the programmed device (i.e. garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.) For convenience, the handheld transmitter of the device may also be used at any time. Erasing Universal - 2007 Chrysler Crossfire | Owner Manual - Page 110
: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. HomeLink is a trademark owned by Johnson Controls, Inc. UMBRELLA HOOK Your Crossfire is equipped with an umbrella hook. This feature is located behind - 2007 Chrysler Crossfire | Owner Manual - Page 111
Ⅵ AM/FM Stereo Radio With Single-Disc CD Player ...126 ▫ Infinity Modulus Entertainment Systems ...126 ▫ CD Player Operation ...130 ▫ User Menu ...132 ▫ User Memory (User Setting - Heater ...136 ▫ Basic Setting - Air Conditioner ...137 ▫ Dust Filter (If Equipped) ...140 ▫ Operating Tips ...141 4 - 2007 Chrysler Crossfire | Owner Manual - Page 112
112 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENTS AND CONTROLS - 2007 Chrysler Crossfire | Owner Manual - Page 113
UNDERSTANDING YOUR INSTRUMENT PANEL 113 INSTRUMENT CLUSTER The instrument cluster displays are activated by either opening the door, pressing the left button within the cluster, or turning the key in the ignition switch to the ON/RUN position. 4 - 2007 Chrysler Crossfire | Owner Manual - Page 114
the ON/RUN position, the indicator light comes on. It should go out when the engine is running. If the indicator light does not go out after starting the engine, or if or water, depending on ambient temperature. The reservoir for the windshield washer system is located in the engine compartment and - 2007 Chrysler Crossfire | Owner Manual - Page 115
in your tires changes with temperature. A significant decrease in temperature could reduce cold inflation pressure below the TPMS setpoint. ALWAYS check pressure in your tires if the TPMS telltale lamp is illuminated. 3. Coolant Indicator Light This indicator illuminates when the engine coolant has - 2007 Chrysler Crossfire | Owner Manual - Page 116
YOUR INSTRUMENT PANEL If the pointer rises to the red (Hot) area, stop the vehicle and turn off the engine until the problem is corrected. down. The switch is automatically canceled when the steering wheel is turned to a large enough degree. The arrows in the instrument cluster will flash - 2007 Chrysler Crossfire | Owner Manual - Page 117
brake warning light will come on if the ABS light is not functioning and there is an ABS system malfunction. 11. Light Outage Indicator With the key in the ignition switch turned to the ON/RUN position, an indicator light comes on. It should go out when the engine is running. If the indicator light - 2007 Chrysler Crossfire | Owner Manual - Page 118
ignition switch turned to the ON/RUN position, and should go out with the engine running. If the ABS warning indicator light comes on while the engine is running, it indicates that the ABS has detected a malfunction and has switched off. In this case, the brake system functions in the usual manner - 2007 Chrysler Crossfire | Owner Manual - Page 119
that must be repaired immediately at an authorized dealer. If the charging system indicator light comes on, or a loss of power steering assistance is noticeable while the engine is running, this may indicate that the accessory drive belt has broken. Should this condition occur, the belt must be - 2007 Chrysler Crossfire | Owner Manual - Page 120
knob/button located to the left of the clock. 18. Gear Indicator For automatic transmission vehicles ON/RUN or ACC position. The knob/ button located just to the left of the clock is used to change the of Instrument Lights, for Resetting Trip Odometer and Flexible Service System (FSS) Indicator - 2007 Chrysler Crossfire | Owner Manual - Page 121
service. This symbol represents Service A. This second symbol represents Service B. Depending on operating conditions throughout the year, the next service 4. Press and hold the knob/button, while turning the key to ON/RUN again. The present status for days or distance is displayed once more. - 2007 Chrysler Crossfire | Owner Manual - Page 122
your reference numbers, the scheduled services as posted in the Service Booklet must be followed to properly care for your vehicle. 23. Outside Temperature Display The temperature display is located on the left side of the instrument cluster, below the fuel and engine temperature gauges. The sensor - 2007 Chrysler Crossfire | Owner Manual - Page 123
. Airbag Light The operational readiness of the airbag system is verified by the airbag indicator light in Light With the key in the ignition and turned to the ON/RUN position, the indicator light in the instrument cluster comes on. It should go out when the engine is running. If the indicator light - 2007 Chrysler Crossfire | Owner Manual - Page 124
in the ignition and turned to the ON/RUN position, the brake wear indicator light comes on. The light goes out when the engine is running. If the indicator light comes on during braking, this indicates the brake pads are worn down. Have the brake system checked at your authorized dealer as soon as - 2007 Chrysler Crossfire | Owner Manual - Page 125
level system is indicated. A conveniently located dipstick allows manual checking of the oil level. If no leaks are noted, continue to drive to the nearest service station where the engine oil should be topped to the "full" mark on the dipstick with an approved oil. 29. Low Fuel Warning Light When - 2007 Chrysler Crossfire | Owner Manual - Page 126
User's Manual) AM/FM STEREO RADIO WITH SINGLE-DISC CD PLAYER INFINITY MODULUS Entertainment Systems A premium Infinity Modulus AM/FM stereo, single-disc CD audio system is standard /OFF knob, but it will switch off automatically after one hour. The volume is controlled by rotating the ON/OFF knob to - 2007 Chrysler Crossfire | Owner Manual - Page 127
pressing OPT, CD, AM, FM, or TP, the current setting is cancelled, and the new setting is stored. FM1 - FM2 - FM AS - BEST FM The system has four FM memory modes that can be selected by repeatedly pressing the FM button. FM1 - One of ten memorized FM station frequencies can be - 2007 Chrysler Crossfire | Owner Manual - Page 128
feature BEST FM - The BEST FM function automatically memorizes and continuously updates the frequencies will change the FM frequency to the next higher or lower station with a strong signal. To manually step or until another mode is selected. Radio Data System (RDS) Stations PTY (Program Type) The - 2007 Chrysler Crossfire | Owner Manual - Page 129
are not met, the unit will only display the frequency. The following are examples of program types displayed: • NEWS - News Service • SOFT - Soft Music • INFORM - Information Programs • NOSTALGA - Nostalgia • SPORTS - Sports Reports • JAZZ - Jazz Music • TALK - Talk Programs • CLASSICL - Classical - 2007 Chrysler Crossfire | Owner Manual - Page 130
system will change the AM frequency to the next higher or lower station with a strong signal. To manually step through the selection was set. AM AS - An autostore feature will store the 9 current stations with the strongest undesired operation. NOTE: Changes or modifications not expressly approved - 2007 Chrysler Crossfire | Owner Manual - Page 131
CD is already loaded can result in a jammed mechanism which may require service at an authorized dealer. Insert the CD into the slot with the printed back, the unit automatically begins to play the first track again. To eject a disc, briefly press and release the EJT button. Features of the CD - 2007 Chrysler Crossfire | Owner Manual - Page 132
track to be played. Press the button again to cancel the feature. NOTE: To protect the unit from excessive heat, a temperature protection user action must be entered within six seconds or this menu is exited automatically. Your current setting can be cancelled and the selections made will be saved - 2007 Chrysler Crossfire | Owner Manual - Page 133
AUTO or MONO is displayed (depending on AUTO - Setting for normal operation. The unit switches from stereo to mono and back, depending is routed through the speaker system. The setting DRIVER is used DRIVER R is displayed (depending on the currently selected setting the speaker system. This eliminates - 2007 Chrysler Crossfire | Owner Manual - Page 134
rotary control/push button repeatedly until AUDIO PH or PH MUTE is displayed (depending on the currently selected setting, you may need to turn the knob too high. RADIO ANTENNA The radio antenna is located in the rear liftgate glass on the coupe vehicles and mounted on the left rear body panel - 2007 Chrysler Crossfire | Owner Manual - Page 135
to balance the temperature, amount and direction of the air circulating throughout the vehicle. The system is always at operational readiness, except when manually switched off. The climate control only operates with the engine running. The climate control removes a considerable amount of moisture - 2007 Chrysler Crossfire | Owner Manual - Page 136
can automatically reach that selection as quickly as possible. The inside temperature will not heat or cool any quicker by setting the selector higher or lower upon initial start up. Fan Control Use this control to regulate the amount of air volume moving through the system in any mode you select - 2007 Chrysler Crossfire | Owner Manual - Page 137
. Open left and right side air outlets. NOTE: The air conditioning compressor will not run if the fan control switch is not set to position 1 or higher. NOTE: The dot between the air distribution control icons is a mix position between the two modes. Slight changes in engine speed or power may be - 2007 Chrysler Crossfire | Owner Manual - Page 138
fan control switch. Close the center and right side air outlets. Turn the defroster outlets for the side windows to the detent position. Ventilation To receive outside air through the panel outlets, turn off the Air Conditioning ON/OFF switch. The light in the switch should be off. Set the controls - 2007 Chrysler Crossfire | Owner Manual - Page 139
is only partially charged, it is possible that the defroster will automatically turn itself off. When this happens, the indicator light inside the switch starts blinking. As soon as the battery has sufficient voltage, the defroster automatically turns itself back on. CAUTION! To avoid damaging the - 2007 Chrysler Crossfire | Owner Manual - Page 140
. The indicator light in the button goes out. The system will automatically shut off if you turn the key in the ignition switch to the ON/RUN position, after approximately 30 minutes, or if the battery voltage drops. NOTE: This vehicle is equipped with an air conditioner system that uses R-134a - 2007 Chrysler Crossfire | Owner Manual - Page 141
UNDERSTANDING YOUR INSTRUMENT PANEL 141 Operating Tips 4 - 2007 Chrysler Crossfire | Owner Manual - Page 142
- 2007 Chrysler Crossfire | Owner Manual - Page 143
Engine Fails To Start ...146 ▫ After Starting ...147 Ⅵ Transmission Shifting ...147 ▫ Manual Transmission ...147 ▫ Recommended Shift Speeds ...148 ▫ Automatic (Limp Home Mode) ...155 Ⅵ Parking Brake ...156 Ⅵ Brake System ...157 ▫ Brake Assist System (BAS) ...157 ▫ Electronic Stability Program - 2007 Chrysler Crossfire | Owner Manual - Page 144
144 STARTING AND OPERATING ▫ Synchronizing ESP ...161 ▫ ESP Control Switch ...161 ▫ Anti-Lock Brake System (ABS) ...162 ▫ Brake Pad Break-In ...166 Ⅵ Power Steering ...166 Ⅵ Tire Safety Information ...167 ▫ Tire Markings ...167 ▫ Tire Identification Number (TIN) ...170 ▫ Tire Loading And Tire - 2007 Chrysler Crossfire | Owner Manual - Page 145
the ON/RUN position. Apply the brakes before shifting into any driving gear. Normal Starting Vehicles with automatic transmissions: system checked at the nearest authorized dealer. Vehicles with manual transmissions: Do not depress the accelerator. Fully depress the clutch pedal, otherwise the engine - 2007 Chrysler Crossfire | Owner Manual - Page 146
feature, the key must be turned completely to the left before attempting to start the engine again. If Engine manual for proper jump-starting procedures. WARNING! Never pour fuel or other flammable liquid into the throttle body air powered battery and an electric engine block heater. - 2007 Chrysler Crossfire | Owner Manual - Page 147
will automatically decrease as the engine warms up. TRANSMISSION SHIFTING Manual Transmission CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. If the engine has been flooded, it may start to run, but - 2007 Chrysler Crossfire | Owner Manual - Page 148
engine. For most city driving, you will find it easier to use only the lower gears. For steady highway driving with light accelerations, sixth gear is recommended. Never drive with your foot resting on the clutch a desired acceleration rate. MANUAL TRANSMISSION RECOMMENDED SHIFT SPEEDS 1-2 2-3 3-4 - 2007 Chrysler Crossfire | Owner Manual - Page 149
individual gears automatically, dependent upon: • Selector lever position • Program mode selector switch • Accelerator position • Vehicle speed CAUTION! If you skip more than one gear while downshifting or downshift at too high an engine speed, you could damage the engine, transmission, or clutch. - 2007 Chrysler Crossfire | Owner Manual - Page 150
dependent on the driving style, the driving situation and the road characteristics. The selector lever is automatically locked while in the PARK position. To move the selector lever out of the PARK position, the brake engine is idling normally and the brake pedal is applied. Do not release the brake - 2007 Chrysler Crossfire | Owner Manual - Page 151
vehicle speed by gradually releasing the brakes. Accelerate gently and never abruptly system malfunction indicator light to come on. Turn off the engine and restart the engine to electrical system, the selector lever could remain locked in the PARK position. To unlock the selector lever manually, - 2007 Chrysler Crossfire | Owner Manual - Page 152
is transmitted from the engine to the drive axle. When the brakes are released, the Limited Warranty. Drive The transmission automatically Dependent on the program mode selector switch position "S" or "W," the maximum speed in the REVERSE gear is different. However, it is not possible to change - 2007 Chrysler Crossfire | Owner Manual - Page 153
to a lower gear if the engine's revolutions per minute limit would be exceeded. Briefly press the road surfaces, never downshift in order to obtain braking action. This could result in drive wheel slip delayed, depending on vehicle speed and engine temperature. This allows the catalytic converter to - 2007 Chrysler Crossfire | Owner Manual - Page 154
the key is in the ON/RUN position, you must press the brake pedal to shift out of the PARK position. PARK supplements the parking brake by locking the transmission. The engine can be started in this range. the accelerator pedal in slow, small movements, will cause the automatic transmission to shift - 2007 Chrysler Crossfire | Owner Manual - Page 155
may be accompanied by the CHECK ENGINE light in the instrument cluster coming on change of driving characteristics for which you may not be prepared. 1. Stop the vehicle. 2. Move the selector lever to the PARK position. 3. Turn off the engine. 4. Wait approximately 10 seconds. 5. Restart the engine - 2007 Chrysler Crossfire | Owner Manual - Page 156
dealer as soon as possible. PARKING BRAKE When you apply the parking brake with engine running, the brake system warning light in the instrument cluster will come on. NOTE: This light, when illuminated with parking brake application, shows only that the parking brake is on. It does not show - 2007 Chrysler Crossfire | Owner Manual - Page 157
, and activation of the brake warning light during brake use. Brake Assist System (BAS) The BAS is designed to maximize the vehicle's braking capability during emergency braking maneuvers. Maximum power boost is applied to the brakes more quickly in emergency braking conditions. This can help reduce - 2007 Chrysler Crossfire | Owner Manual - Page 158
BAS assistance. To receive the benefit of the system you must apply continuous, full braking power during the stopping sequence. Do not reduce brake pedal pressure. Once the brake pedal is released, the BAS is deactivated. The malfunction indicator light for the BAS is combined with the Electronic - 2007 Chrysler Crossfire | Owner Manual - Page 159
brake system functions in the usual manner, but without BAS. With the ABS malfunctioning, the BAS and ESP will be disabled. In this condition, both malfunction indicator lights come on while the engine is running. If the malfunction indicator light engine torque is limited and the ESP warning light - 2007 Chrysler Crossfire | Owner Manual - Page 160
light starts light manual), the engine must be shut off (key in the ignition switch turned to the OFF/LOCK or ACC position). Otherwise, the ESP will immediately be engaged and will apply the rear wheel brakes. NOTE: When the ESP warning light Limited Warranty. NOTE: If the ESP warning light - 2007 Chrysler Crossfire | Owner Manual - Page 161
161 Synchronizing ESP If the power supply was interrupted (battery disconnected or discharged), the BAS/ESP malfunction indicator light may be illuminated with the engine running. To re-synchronize the ESP, and cancel the malfunction indicator light, the steering angle sensor will need to be - 2007 Chrysler Crossfire | Owner Manual - Page 162
With the ESP system switched off, the engine torque reduction feature is cancelled. Therefore light goes out). Anti-Lock Brake System (ABS) The ABS gives increased vehicle stability and brake performance under most braking conditions. The system automatically "pumps" the brakes during severe braking - 2007 Chrysler Crossfire | Owner Manual - Page 163
-lock brake system conducts a low-speed self-test at about 12 mph (20 km/h). If you have your foot lightly on the brake while brake system is functioning. 5 WARNING! Significant over- or under-inflation of tires, or mixing sizes of front or rear tires or wheels on the vehicle can reduce braking - 2007 Chrysler Crossfire | Owner Manual - Page 164
by an authorized dealer. When the ABS malfunction indicator light in the instrument cluster comes on while the engine is running, it indicates that the ABS has detected a malfunction and has switched off. In this case, the brake system functions in the usual manner, but without antilock assistance - 2007 Chrysler Crossfire | Owner Manual - Page 165
. This hydroplaning action can cause loss of traction, braking ability, and control. • After going through deep water or a car wash, brakes may become wet, resulting in decreased performance and unpredictable braking action. Dry the brakes by gentle, intermittent pedal action while driving at very - 2007 Chrysler Crossfire | Owner Manual - Page 166
Brake Pad Break-In The brakes on your vehicle do not require a long break-in period, but avoid repeated hard brake applications from high speeds during initial break-in. Also avoid severe brake does not indicate that there is a problem with the power steering system. Upon initial start-up in cold - 2007 Chrysler Crossfire | Owner Manual - Page 167
into the sidewall beginning with the section width. The letter ЉPЉ is absent from this tire size designation. Example: 215/65R15 96H. NOTE: LT(Light Truck)-Metric tire sizing is based on U.S. design standards. The size designation for LT-Metric tires is the same as for P-Metric tires except for the - 2007 Chrysler Crossfire | Owner Manual - Page 168
168 STARTING AND OPERATING EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ؆...blank...؆ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) - 2007 Chrysler Crossfire | Owner Manual - Page 169
169 Service Description: 95 = Load Index -A numerical code associated vehicle loading, road conditions and posted speed limits.) Load Identification: ؆...blank...؆ = Absence of Load (XL) = Extra Load (or Reinforced) Tire Light Load = Light Load Tire C,D,E = Load range associated with the maximum - 2007 Chrysler Crossfire | Owner Manual - Page 170
full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted use. MA = Code representing the tire manufacturing location. (2 digits) L9 = Code representing the tire size. (2 digits) ABCD = Code used by tire - 2007 Chrysler Crossfire | Owner Manual - Page 171
Loading Information" placard located on the driver's side "B" pillar. Tire and Loading Information Placard 5 This placard tells you important information about: 1. the number of people that can be carried in the vehicle 2. the total weight your vehicle can carry 3. the tire size designed for your - 2007 Chrysler Crossfire | Owner Manual - Page 172
to the loading conditions, tire size and cold tire inflation pressures specified on the Tire placard and the Vehicle Loading section of this manual. NOTE: Under a maximum loaded vehicle condition, here. Steps for Determining Correct Load Limit 1. Locate the statement "The combined weight of - 2007 Chrysler Crossfire | Owner Manual - Page 173
from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity capacities of your vehicle with varying seating configurations and number and size of occupants. This table is for illustration purposes only and - 2007 Chrysler Crossfire | Owner Manual - Page 174
174 STARTING AND OPERATING - 2007 Chrysler Crossfire | Owner Manual - Page 175
damage that results in tire failure. • Unequal tire pressures can cause steering problems. You could lose control of your vehicle. • Over inflated or under the tire warranty booklet in your Owner's Manual package. It contains valuable information on tire maintenance. Specific recommendations on - 2007 Chrysler Crossfire | Owner Manual - Page 176
contributes to a comfortable ride. Overinflation produces a jarring and uncomfortable ride. Tire Inflation Pressures The proper cold tire inflation pressure for passenger cars is listed on either the face of the driver's door or the driver's side "B" pillar. Tire Placard Orientation tread act The - 2007 Chrysler Crossfire | Owner Manual - Page 177
pressures vary with temperature changes. Tire pressures change by approximately 1 psi (7 kPa) per 12° F (7° C) of air temperature change. Keep this in mind The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be - 2007 Chrysler Crossfire | Owner Manual - Page 178
conditions, do not spin your vehicle's wheels above 35 mph (55 km/h). See the paragraph on Freeing A Stuck Vehicle in Section 6 of this manual. WARNING! WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode - 2007 Chrysler Crossfire | Owner Manual - Page 179
the Tire and Loading Information placard for the size designation of your tire. The service description and load identification will be found on or an authorized tire dealer with any questions you may have on tire specifications or capability. 5 These indicators are molded into the bottom of the - 2007 Chrysler Crossfire | Owner Manual - Page 180
for replacement on the Crossfire. Tires with the same size, speed, or size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking - 2007 Chrysler Crossfire | Owner Manual - Page 181
Check with your authorized dealer before replacing tires with a different size. Alignment And Balance The suspension components of your vehicle should vibration and avoid tire cupping and spotty wear. TIRE PRESSURE MONITOR SYSTEM (If Equipped) The Tire Pressure Monitor System (TPMS) uses wireless - 2007 Chrysler Crossfire | Owner Manual - Page 182
equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use aftermarket tire sealant or balance beads as damage to the sensors may result. The standard TIREFIT system (see Tirefit Tire Repair and Jacking Instructions in the What To Do In - 2007 Chrysler Crossfire | Owner Manual - Page 183
NOTE: The pressure in your tires changes with temperature. A significant decrease system approved for use on the Chrysler Crossfire. Chains should only be used on the rear wheels and only with the recommended winter mud and snow (M+S) tires and wheels. Follow the manufacturer's mounting instructions - 2007 Chrysler Crossfire | Owner Manual - Page 184
for various road conditions. Replacement tires should be of the same size and speed rating to continue to provide the same level of performance tires have reduced traction capability in snow and ice. When driving your Crossfire in these conditions with these tires, you must take special care to - 2007 Chrysler Crossfire | Owner Manual - Page 185
size tire also requires the purchase of two additional wheels with the same size specification as the original equipment front wheels. Snow tires may have a lower speed rating than factory in the "Maintenance Schedules" Section of this manual. More frequent rotation is permissible if desired. The - 2007 Chrysler Crossfire | Owner Manual - Page 186
to minimize the potential for engine damage. Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark Engine damage resulting from operating with a heavy spark knock may not be covered by the new vehicle warranty. Poor quality gasoline can cause problems - 2007 Chrysler Crossfire | Owner Manual - Page 187
blends may result in starting and drivability problems and may damage critical fuel system components. Problems that result from using methanol/gasoline blends are not the responsibility of DaimlerChrysler Corporation and may not be covered by the Limited Warranty. While MTBE is an oxygenate made - 2007 Chrysler Crossfire | Owner Manual - Page 188
in unnecessary cost. Therefore specifications, but emission control system performance may be adversely affected. Gasoline sold outside of California is permitted to have higher sulfur levels, which may affect the performance of the vehicle's catalytic converter. This may cause the CHECK ENGINE light - 2007 Chrysler Crossfire | Owner Manual - Page 189
door. CAUTION! If the CHECK ENGINE Light is flashing, immediate service is required. See the Onboard Diagnostic System (OBDII) paragraph in the Maintaining Your Vehicle section of this manual. 5 ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is located under the fuel filler door, on - 2007 Chrysler Crossfire | Owner Manual - Page 190
driving, it indicates that the fuel level is down to the reserve quantity of approximately 2 gallons (7.5 liters). Leaving the engine running and the fuel cap open can cause the CHECK ENGINE light to illuminate. NOTE: • When the fuel nozzle "clicks" or shuts off, the fuel tank is full. • Tighten the - 2007 Chrysler Crossfire | Owner Manual - Page 191
115 lbs (52 kg) Rated Vehicle Capacity ...415 lbs (188 kg) Roof Luggage Rack Convertible Top Vehicles CAUTION! To prevent damage to the convertible top, DO NOT carry any loads on the convertible top. Coupe Vehicles External racks do not increase the total load carrying capacity of the vehicle. Be - 2007 Chrysler Crossfire | Owner Manual - Page 192
capacity of your roof luggage rack system maximum load capacity. Always distribute heavy loads as evenly as possible and secure the load appropriately. • Long loads which extend over the windshield, such as on your roof rack. TRAILER TOWING Trailer towing with your Crossfire is not recommended. - 2007 Chrysler Crossfire | Owner Manual - Page 193
CONTENTS Ⅵ Hazard Warning Flasher ...194 Ⅵ If Your Engine Overheats ...194 Ⅵ TIREFIT Tire Repair And Jacking ...195 ▫ TIREFIT ...195 ▫ Preparations For Jacking ...198 ▫ Jack Location And Instructions ...200 Ⅵ Jump-Starting The Battery ...203 Ⅵ Driving On Slippery Surfaces ...205 ▫ Traction - 2007 Chrysler Crossfire | Owner Manual - Page 194
The flasher switch is located in the console. Push in the flasher switch and all front and rear directional signals will flash. Press the flasher switch a second time to turn the flashers off. NOTE: With extended use, the flasher may run down your battery. IF YOUR ENGINE OVERHEATS During severe - 2007 Chrysler Crossfire | Owner Manual - Page 195
your air conditioner is on, turn it off. The air conditioning system adds heat to the cooling system and engine immediately. You may want to call an authorized dealer for service. If you decide to look under the hood yourself, see Section 7 of this manual. Follow the warnings under the Cooling System - 2007 Chrysler Crossfire | Owner Manual - Page 196
with plenty of water. If clothing comes in contact with TIREFIT, change clothing as soon as possible. In case of allergic reaction or rash heat source. 1. TIREFIT sealant bottle 2. Air pump flap 3. Recess in air pump 4. Power plug and cable 5. Air pump hose with pressure gauge 6. Hose connection - 2007 Chrysler Crossfire | Owner Manual - Page 197
brake and turn on the hazard warning flashers. 2. Move the transmission selector lever to the PARK position (manual transmission to FIRST or REVERSE gear) and turn off the engine. 3. Remove the TIREFIT kit and electric air the ON/RUN position. 12. Press the switch on the air pump to 1. The air pump - 2007 Chrysler Crossfire | Owner Manual - Page 198
the air pump switch to 0, turn the ignition switch to the OFF/LOCK position, and disconnect the TIREFIT system. 17 at the earliest opportunity at an authorized dealer or tire service center. NOTE: Do not exceed 50 mph (80 Never start or run the engine while the vehicle is on a jack. If you - 2007 Chrysler Crossfire | Owner Manual - Page 199
with TIREFIT.) 6 • Turn on the hazard warning flashers and park the vehicle on a firm, level surface; avoid ice or slippery areas. • Firmly set the parking brake and shift the transmission selector lever into PARK (manual transmission to FIRST or REVERSE gear). • Turn off the - 2007 Chrysler Crossfire | Owner Manual - Page 200
Block the wheel diagonally opposite the flat tire. Jack Location and Instructions • Passengers must not remain in the vehicle when the vehicle is jacked. NOTE: The jack is designed exclusively for jacking up the vehicle at the specified jack location points built beneath either side of the vehicle - 2007 Chrysler Crossfire | Owner Manual - Page 201
WHAT TO DO IN EMERGENCIES 201 6 - 2007 Chrysler Crossfire | Owner Manual - Page 202
vehicle only enough to make the necessary repair. 3. Holding the jack, insert the cradle under the lifting points. Crank the handle clockwise until the jack base meets the ground. Place the jack on firm ground. Position the jack so that it is always level, even if the vehicle is parked on - 2007 Chrysler Crossfire | Owner Manual - Page 203
cannot be started this way. Pushing with another vehicle may damage the transmission or the rear of your vehicle. If your vehicle has a discharged (dead) battery, booster cables may be used to obtain a start from another vehicle. This type of start can be dangerous if done improperly, so follow the - 2007 Chrysler Crossfire | Owner Manual - Page 204
that might make an inadvertent electrical contact. 2. When boost is provided by a battery in another vehicle, park that vehicle within booster cable reach but without letting the vehicles touch. Set the parking brake, place the transmission in Neutral and turn the ignition OFF for both vehicles - 2007 Chrysler Crossfire | Owner Manual - Page 205
which has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. 7. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fans. NOTE: If engine does not run after several unsuccessful - 2007 Chrysler Crossfire | Owner Manual - Page 206
to the ON/RUN position, the vehicle doors lock if the left front wheel and the right rear wheel are turning at vehicle speeds of approximately 9 mph (15 km/h) or more. To prevent the vehicle door locks from locking, deactivate the automatic central locking. CAUTION! Racing the engine or spinning - 2007 Chrysler Crossfire | Owner Manual - Page 207
wheels raised, the engine must be shut off (key in the ignition switch turned to the OFF/LOCK or ACC positions). Otherwise, the ESP will immediately be engaged and will apply the rear wheel brakes. Switch off the tow-away alarm as well as the automatic central locking system. Towing restrictions for - 2007 Chrysler Crossfire | Owner Manual - Page 208
to allow the vehicle to be easily drawn up on a flatbed tow truck. The rear towing eye is located on the right side of the vehicle below the rear fascia. The front hook is located behind the lower grille in the fascia. For access, a snap-in grille must be removed using the - 2007 Chrysler Crossfire | Owner Manual - Page 209
WHAT TO DO IN EMERGENCIES 209 6 Insert the tool (or similar sized screwdriver) into the slot in the grille as shown (the tool must be inserted far enough to engage the clip on the left side of - 2007 Chrysler Crossfire | Owner Manual - Page 210
on the key fob. To prevent triggering the tow-away alarm feature, press the tow-away alarm switch to turn off the tow-away alarm before towing the vehicle, or when parking on a surface subject to movement, such as a ferry or auto train. To do so, turn the key in the ignition - 2007 Chrysler Crossfire | Owner Manual - Page 211
properly? • Is there sufficient battery voltage? Start the engine if necessary. • Is the rear cargo compartment divider secured in the vertical position? If the power convertible top operation does not function properly, you can close the convertible top manually. NOTE: The multifunction tool from - 2007 Chrysler Crossfire | Owner Manual - Page 212
" and continue to push down on the switch for 5 seconds. 4. After 5 seconds the hydraulic system pressure will be relieved. CAUTION! Ensure that the decklid is closed while raising the convertible top manually to prevent the possibility of contact between the decklid and the tonneau cover. WARNING - 2007 Chrysler Crossfire | Owner Manual - Page 213
IN EMERGENCIES 213 6 4. Open the tonneau cover and secure it in the upright position. 5. Pull up hard on the upper section of the convertible top to move it out of its storage compartment. NOTE: Do not let go of the convertible top as it may fall back into the convertible top storage compartment. - 2007 Chrysler Crossfire | Owner Manual - Page 214
top toward the windshield header. 8. Place the rear window section of the convertible top in its vertical position. 9. Close the tonneau cover by placing hands near the edges (arrows) and slowly lowering it. The tonneau cover must lock - 2007 Chrysler Crossfire | Owner Manual - Page 215
cover. Turn the wrench in the direction of the arrow to its stop and remove the tool. 11. Lower the rear window section of the convertible top down and lock into the tonneau cover. 6 12. Fold down the locking latch handle. - 2007 Chrysler Crossfire | Owner Manual - Page 216
EMERGENCIES 13. Turn the latch handle just past one quarter turn clockwise and pull the convertible top frame carefully down until it meets the windshield header attachment points. 15. Fold the latch handle up. The convertible top is now locked onto the windshield header. 14. Turn the latch handle - 2007 Chrysler Crossfire | Owner Manual - Page 217
WHAT TO DO IN EMERGENCIES 217 Opening a Locked Decklid It is possible for the decklid to become locked if a convertible top system malfunction occurs. If the top is manually moved to the full up or full down position when the hydraulic pressure is relieved, the decklid should unlock. 6 - 2007 Chrysler Crossfire | Owner Manual - Page 218
- 2007 Chrysler Crossfire | Owner Manual - Page 219
Service ...224 Ⅵ Maintenance Procedures ...225 ▫ Engine Oil ...225 ▫ Ignition Wiring System ...231 ▫ Crankcase Emission Control System ...231 ▫ Maintenance-Free Battery ...231 ▫ Air Exhaust System ...237 ▫ Cooling System ...238 ▫ Hoses And Vacuum/Vapor Harnesses ...241 ▫ Brakes ...242 ▫ Automatic - 2007 Chrysler Crossfire | Owner Manual - Page 220
220 MAINTAINING YOUR VEHICLE ▫ Manual Transmission ...245 ▫ Appearance Care And Protection From Corrosion ...246 Ⅵ Convertible Top Care ...251 ▫ Washing ...251 ▫ General Cleaning ...252 ▫ Weather Strip Care ...252 Ⅵ Fuses ...253 ▫ Underhood Accessory Fuse Block Fuses ...253 ▫ Relay Control Module - 2007 Chrysler Crossfire | Owner Manual - Page 221
MAINTAINING YOUR VEHICLE 221 3.2L ENGINE 7 - 2007 Chrysler Crossfire | Owner Manual - Page 222
emissions well within current government regulations. If any of these systems require service, the OBD II system will turn on the CHECK ENGINE Light. It will also store diagnostic codes and other information to assist your service technician in making repairs. Although your vehicle will usually be - 2007 Chrysler Crossfire | Owner Manual - Page 223
ENGINE Light is functioning and is not on when the engine is running, and that the OBD (Onboard Diagnostic) system is ready for testing. Normally, the OBD system will be ready. The OBD system may not be ready if your vehicle was recently serviced, if you recently had a dead battery, or a battery - 2007 Chrysler Crossfire | Owner Manual - Page 224
's OBD system is ready or not ready, if the CHECK ENGINE light is illuminated during normal vehicle operation, you should have your vehicle serviced before going to the I/M station. The I/M station can fail your vehicle because the CHECK ENGINE light is on with the engine running. REPLACEMENT - 2007 Chrysler Crossfire | Owner Manual - Page 225
Level in the Understanding Your Instrument Panel section, or by checking the engine oil dipstick. MAINTENANCE PROCEDURES The pages that follow contain the maintenance service recommended by the engineers who designed your vehicle. Besides the maintenance items for which there are fixed maintenance - 2007 Chrysler Crossfire | Owner Manual - Page 226
226 MAINTAINING YOUR VEHICLE The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off, or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. - 2007 Chrysler Crossfire | Owner Manual - Page 227
cluster. NOTE: Also see the FSS system details in the Understanding Your Instrument Panel section of this manual. Very light duty driving cycles (most trips more than 10 miles [16 km] at moderate speeds in moderate temperature conditions) can extend the service interval beyond 7,000 miles (Canada - 2007 Chrysler Crossfire | Owner Manual - Page 228
, can present a problem to the environment. Contact your dealer, service station, or governmental agency for advice on how and where used oil can be safely discarded in your area. Engine Oil Filter The engine oil filter should be replaced at every engine oil change. Engine Oil Filter Selection All - 2007 Chrysler Crossfire | Owner Manual - Page 229
and procedures shown in the Service Manual. Special tools are required to properly measure tension and to restore belt tension to factory specifications. Also, check belt routing to make sure there is no interference between the belts and other engine components. Spark Plugs Spark plugs - 2007 Chrysler Crossfire | Owner Manual - Page 230
involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the vehicle. WARNING! A hot exhaust system can - 2007 Chrysler Crossfire | Owner Manual - Page 231
suggest severe and abnormal catalyst overheating. If this occurs, stop the vehicle, turn off the engine and allow it to cool. Service, including a tune up to DaimlerChrysler Corporation's specifications, should be obtained immediately. To minimize the possibility of catalyst damage: • Do not shut - 2007 Chrysler Crossfire | Owner Manual - Page 232
fast charger" is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to battery. Do not use a "fast charger" to provide starting voltage as battery damage can result. Air Conditioner Check the air conditioning system at the start of the warm - 2007 Chrysler Crossfire | Owner Manual - Page 233
the condenser as required. Fabric front fascia protectors may reduce air flow to the condenser, reducing air conditioning performance. Power Steering Fluid No power steering fluid service is required. The system is filled at the factory with Pentosin CHF 11S. Steering noise and reduced component - 2007 Chrysler Crossfire | Owner Manual - Page 234
lower ball joints that are permanently lubricated. Inspect these ball joints whenever under-vehicle service is done. Steering Linkage Inspect tie rod ends whenever the vehicle is serviced. They are permanently lubricated and do not require periodic lubrication. Drive Shaft Universal Joints - 2007 Chrysler Crossfire | Owner Manual - Page 235
easy operation and to protect against rust and wear. Hood Latch When performing other under hood services, the hood latch release mechanism and safety catch should be inspected, cleaned, and lubricated. It the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. 7 - 2007 Chrysler Crossfire | Owner Manual - Page 236
The washer fluid reservoir is located in the engine compartment and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) rated not to freeze at -25°F (-31°C). Operate the system - 2007 Chrysler Crossfire | Owner Manual - Page 237
The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system, or if exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have - 2007 Chrysler Crossfire | Owner Manual - Page 238
or hear steam coming from under the hood, don't open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot. Coolant Checks Check coolant protection every 12 months (before the onset of freezing weather, where applicable). If the - 2007 Chrysler Crossfire | Owner Manual - Page 239
cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Engine Coolant Disposal Used ethylene glycol based engine approved to MB 325.0, such as Valvoline GO5, or an equivalent extended life coolant. Refer to the recommended Fluids, Lubricants and Genuine Parts - 2007 Chrysler Crossfire | Owner Manual - Page 240
products will decrease the life of the engine coolant and will require more frequent coolant changes. Please note that it is the an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or - 2007 Chrysler Crossfire | Owner Manual - Page 241
engine cooling system that contains aluminum components. • Make sure that the radiator and coolant bottle hoses are not kinked or obstructed. • Keep the front of the radiator clean. If your vehicle has air conditioning, keep the front of the condenser clean, also. • Do not change the exhaust - 2007 Chrysler Crossfire | Owner Manual - Page 242
Brakes In order to assure brake system performance, all brake system components should be inspected periodically. Suggested service intervals can be found in the Maintenance section. Brake and Power Steering System Hoses When servicing heat sources, such as the exhaust manifold. Inspect all hose - 2007 Chrysler Crossfire | Owner Manual - Page 243
the brake system warning light is on. Be sure to clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reservoir. Fluid level can be expected to fall as the brake pads wear. Brake fluid - 2007 Chrysler Crossfire | Owner Manual - Page 244
or unidentified as to specification, may result in sudden brake failure during hard prolonged braking. You could have an accident. Automatic Transmission The fluid in the automatic transmission should be changed at 80,000 miles (129,000 km), along with the transmission fluid filter. After that, the - 2007 Chrysler Crossfire | Owner Manual - Page 245
Changes Automatic transmission fluid and filter should be changed at 80,000 miles (129,000 km). The fluid is then filled for life. NOTE: Refer to Section 8 of this manual for Maintenance Schedules. Manual Transmission Selection of Lubricant No fluid service is required. Use only fluid approved - 2007 Chrysler Crossfire | Owner Manual - Page 246
Change Under normal operation conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes from Corrosion Vehicle body protection requirements vary according to geographic locations and usage. Chemicals that make roads passable in snow - 2007 Chrysler Crossfire | Owner Manual - Page 247
sap and tar. • Salt in the air near seacoast localities. • Atmospheric fallout/ in the shade using a mild car wash soap, and rinse the panels as soon as possible. • Use Mopar auto polish to remove road film and stains and cost of such repairs is considered the responsibility of the owner. 7 - 2007 Chrysler Crossfire | Owner Manual - Page 248
Your dealer has touch-up paint to match the color of your vehicle. • If your vehicle is damaged vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of cleaner. Do not use scouring pads or metal polishes. Avoid automatic car washes that use acidic solutions - 2007 Chrysler Crossfire | Owner Manual - Page 249
to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, detergents, or ammonia based cleaners to clean your leather upholstery. Application of a leather conditioner is not required to maintain the original condition. CAUTION! The use - 2007 Chrysler Crossfire | Owner Manual - Page 250
250 MAINTAINING YOUR VEHICLE To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing. Do not use abrasive cleaning components, solvents, - 2007 Chrysler Crossfire | Owner Manual - Page 251
the material and cause the top to leak. • Never use a power washer to clean the top, as you may damage the top material. • If an automatic car wash is used, never use hot-wax. Hand washing is highly recommended. Automatic car washing equipment can damage the top material. If you must use an - 2007 Chrysler Crossfire | Owner Manual - Page 252
and Stain Removers • Glass Cleaner • Similar Organic Solvents • Abrasive Type Cleaners or Bleaches The following methods are sufficient if the top is only lightly soiled: Dry Cleaning Brush the dry top with a soft-bristled brush from front to rear of the vehicle. Wet Cleaning Wash with clear water - 2007 Chrysler Crossfire | Owner Manual - Page 253
MAINTAINING YOUR VEHICLE 253 FUSES Underhood Accessory Fuse Block Fuses The underhood accessory fuse block fuses are located under the hood on the driver's side, between the brake master cylinder and the left front fender. To remove the lid, squeeze the tabs together located at the front of the - 2007 Chrysler Crossfire | Owner Manual - Page 254
is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it shows a problem in the circuit that must be corrected. - 2007 Chrysler Crossfire | Owner Manual - Page 255
Beige 40 Amp Orange 5 Amp Beige Circuits Garage Door Opening Signal, Tire Pressure Control and Seat Heater Control Unit Airbag Indicator, Safety Restraint System and Indicator Passenger Airbag Off Heated Mirror Radio (Coupe) Roof Control Module (Roadster) Exterior Mirror Adjustment, Left And Right - 2007 Chrysler Crossfire | Owner Manual - Page 256
32 33 34 34 35 Fuse 15 Amp Blue 15 Amp Blue 5 Amp Beige 30 Amp Green 15 Amp Blue 30 Amp Green 5 Amp Beige 7.5 Amp Brown Circuits Cigar Lighter, Glove Compartment Light Wiper, Washer Pump, Headlight Flasher Control Unit Spare (Coupe) Climate Control (Roadster) Radio Frequency Remote Control, Hazard - 2007 Chrysler Crossfire | Owner Manual - Page 257
Module Fuses The relay control module fuses are located in the Control Module Box next to the battery in the engine compartment. Slide the control module box cover 1 2 3 4 Fuse 15 Amp Blue 15 Amp Blue 15 Amp Blue 40 Amp Orange Circuits Traction System Engine Control 2 Engine Control 1 Air Pump 7 - 2007 Chrysler Crossfire | Owner Manual - Page 258
fuse access door is located on the end of the instrument panel on the driver's side behind the trim panel cover. Use a coin or flat blade screwdriver to open and close this access door. 4 5 Fuse 15 Amp Blue 7.5 Amp Brown 15 Amp Blue 7.5 Amp Brown Circuits Not Assigned Brake Lamp/Speed Control Right - 2007 Chrysler Crossfire | Owner Manual - Page 259
12 13 14 Fuse 15 Amp Blue 7.5 Amp Brown 15 Amp Blue 15 Amp Blue 7.5 Amp Brown 7.5 Amp Brown Circuits Right Low Beam Right Parking/Tail Light Side Marker Left Low Beam Fog Light Left Parking/Tail Light Side Marker License Plate/Instrument Cluster Lighting/Symbol Lighting Not Used - Spare Fuse Not - 2007 Chrysler Crossfire | Owner Manual - Page 260
260 MAINTAINING YOUR VEHICLE EXTERIOR LIGHT BULB SERVICE Headlights 3. Release the spring clamps holding the the bulb Wear eye and hand protection. NOTE: To prevent a possible electrical short circuit, switch off light prior to replacing a bulb. 1. Push the tab down at the top end of the cover and - 2007 Chrysler Crossfire | Owner Manual - Page 261
, turn counterclockwise and remove. • Replace the bulb, push in and twist clockwise. Reinstall the socket, and turn clockwise. Front and Rear Sidemarker Lights 1. Push the front sidemarker assembly in and slide it forward. Push the rear sidemarker assembly in and slide rearward. The assembly will - 2007 Chrysler Crossfire | Owner Manual - Page 262
test the operation of all lights after service operations have been performed to validate an effective repair. License Plate Light 1. Remove the two lens were aimed at the factory. The factory setting was made at a no load setting. A great increase in weight will change the aiming and it may - 2007 Chrysler Crossfire | Owner Manual - Page 263
procedure is contained in the manufacturer's Service Manual. Information on purchasing a Service Manual can be found at the back of this Owner's Manual. VEHICLE STORAGE We recommend that you follow these guidelines before storing your Crossfire for extended periods. • Fill the gas tank. This will - 2007 Chrysler Crossfire | Owner Manual - Page 264
the battery recharge procedure in the Service Manual. • Check that the radiator coolant level of protection is to at least -20°F (-29°C). • Block the wheels. Do not apply the parking brake. • Make sure that all tires are inflated to the optimum pressure. • Cut blocks of plywood about the same size - 2007 Chrysler Crossfire | Owner Manual - Page 265
MAINTAINING YOUR VEHICLE 265 SPECIFICATIONS Engine Specifications Engine Size Mode of Operation No. of Cylinders Horsepower (SAE J 1349) Bore Stroke Torque (SAE J 1349) Firing Order Compression Ratio Spark Plugs Spark Plug Gap Tightening Torque Maximum Engine Speed Accessory Drive Belt 195.2 CID - 2007 Chrysler Crossfire | Owner Manual - Page 266
266 MAINTAINING YOUR VEHICLE Body Specifications Overall Length Maximum Width Maximum Width With Mirrors Overall Height Coupe: Roadster: Front Track Rear Track Wheelbase Front Overhang Rear Overhang 159.8 in. (4058 mm) 69.5 in. (1766 mm) 76.9 in. (1954 mm) 51.5 51.8 58.8 - 2007 Chrysler Crossfire | Owner Manual - Page 267
Engine Oil (with filter) 3.2 L Engine Cooling System * 3.2 L Engine Manual Transmission Automatic Transmission Rear Axle Power Steering Reservoir Brake 1.8 Liters 8.0 Liters 1.3 Liters 1.0 Liters .5 Liters 7.0 Liters U.S. 15.8 Gallons 2 Gallons 8.5 Qts. Metric 60.0 Liters 7.5 Liters 8.0 Liters 7 - 2007 Chrysler Crossfire | Owner Manual - Page 268
FSS may not alert for an oil change at the proper interval if an unapproved engine oil is used; engine damage and reduced engine life may result. Mopar 5102905AA or equivalent Bosch F 8 DPER/NGK PFR 5-11 0.039 in (1.0 mm) Premium Unleaded 91 Octane Engine Oil Filter Spark Plugs Spark Plug Gap Fuel - 2007 Chrysler Crossfire | Owner Manual - Page 269
service required. Only use fluid approved to MB 236.2. SAE 5W-20 engine oil, meeting API SL or GF-3, may be substituted. No fluid service required. Filled at the factory with on driver's door frame. Clutch Fluid Manual Transmission Fluid Power Steering Reservoir 7 Rear Axle Fluid Tire Pressure - 2007 Chrysler Crossfire | Owner Manual - Page 270
Grade 2 EP, GC-LB Hood Springs and Links Mopar Spray White Lube Latches: Liftgate/Decklid Hood/Safety Catch Door Seat Regulator and Track Window System Components Lock Cylinders Spoiler Mopar Mopar Mopar Mopar Mopar Mopar Mopar Spray White Lube Multi-Purpose Lube NLGI Grade 2 EP, GC-LB Spray - 2007 Chrysler Crossfire | Owner Manual - Page 271
System ...276 Ⅵ Regular Check-Ups ...278 M A I N T E N A N C E S ▫ Additional Periodic Maintenance ...279 C Ⅵ Special Maintenance Requirements ...280 E L H D ▫ Coolant ...280 U ▫ Dust Filter For Heating/Ventilation E Replacement (If Equipped) ...280 S Ⅵ Engine Oil Change And Filter Replacement - 2007 Chrysler Crossfire | Owner Manual - Page 272
INTRODUCTION This is intended as a guide to the service requirements of your vehicle. It contains all necessary instructions concerning service intervals and operations which have to be carried out. Scope and frequency of maintenance work primarily depend on the vehicle's operating conditions - 2007 Chrysler Crossfire | Owner Manual - Page 273
your warranty rights. With regard to legal stipulations concerning emissions control, please note that engines have to be serviced and adjusted in accordance with special instructions and using special measuring equipment. Modifications to or interference with the emissions control systems are - 2007 Chrysler Crossfire | Owner Manual - Page 274
replace filter Maintenance • Lubricate hood hinges, latch, and secondary latch • Reset FSS Display Function Check • Horn, hazard warning flashers, turn signals, and indicator lamps • Headlamps and exterior lighting • Windshield wipers and washer system Inspection • Check front and rear brake pads - 2007 Chrysler Crossfire | Owner Manual - Page 275
lamps • Headlamps and exterior lighting • Windshield wipers and washer system • Check seat belts for damage and proper function • Test hydraulic brakes and check parking brake function Inspection • Check • Check • Check • Check A I N front and rear brake pads for lining thickness T E N condition - 2007 Chrysler Crossfire | Owner Manual - Page 276
by regular use, trace and eliminate the cause. • Engine cooling system (check corrosion inhibitor/ antifreeze) • Hydraulic brake system • Power steering system • Windshield washer system FSS SYSTEM The Flexible Service System (FSS) permits a flexible service schedule that is directly related to the - 2007 Chrysler Crossfire | Owner Manual - Page 277
combined with short distance driving in which the engine does not reach normal operating temperature, S C reduce the interval between services. H Regardless of the service interval determined by your D FSS, the scheduled services as posted in this manual must U L be followed to properly care for - 2007 Chrysler Crossfire | Owner Manual - Page 278
wiper blade condition. • Check operation of lighting systems. • Inspect tires for unusual wear, damage, and pressure (at least every 14 days). • Mechanical assemblies (e.g., engine, transmission, etc.) - check for leaks. Once a Month • Inspect the battery and clean and tighten the terminals as - 2007 Chrysler Crossfire | Owner Manual - Page 279
279 M • Change the automatic transmission fluid and filter. Use the recommended automatic transmission fluid. After this change it is filled for life. The manual transmission comes filled for life from the factory. S C Every 100,000 miles (161,000 km) or 5 years: H E • Replace engine coolant using - 2007 Chrysler Crossfire | Owner Manual - Page 280
that can be reached from the passenger foot well provides access to the filter element. ENGINE OIL CHANGE AND FILTER REPLACEMENT The recommended oil and filter change interval is based on FSS or 1 year. Please refer to the heading FSS System in this section for a full description of the use and - 2007 Chrysler Crossfire | Owner Manual - Page 281
YOU NEED CONSUMER ASSISTANCE CONTENTS Ⅵ Suggestions For Obtaining Service For Your Vehicle ...282 ▫ Prepare For The Appointment ...282 ▫ Prepare A List ...282 ▫ Be Reasonable With Requests ...282 Ⅵ If You Need Assistance ...282 Ⅵ Warranty Information ...285 Ⅵ Mopar Parts ...285 Ⅵ Reporting Safety - 2007 Chrysler Crossfire | Owner Manual - Page 282
be covered by the warranty; discuss additional charges with the service manager. Keep a maintenance log of your vehicle's service history. This can often provide a valuable clue to the current problem. Prepare A List Make a written list of your vehicle's problems or the specific work you want done - 2007 Chrysler Crossfire | Owner Manual - Page 283
IF YOU NEED CONSUMER ASSISTANCE 283 This is why you should always talk to your dealer's service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or - 2007 Chrysler Crossfire | Owner Manual - Page 284
Corporation by dialing 1-800-380-CHRY. Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unexpected repairs after your DaimlerChrysler Corporation's new vehicle limited warranty expires. The DaimlerChrysler Corporation stands behind - 2007 Chrysler Crossfire | Owner Manual - Page 285
, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, and the DaimlerChrysler Corporation. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424-9393 (or 366-0123 in Washington, D.C. area - 2007 Chrysler Crossfire | Owner Manual - Page 286
of the vehicle, system and/or components is written in straightforward language with illustrations, diagrams and charts. • Owner's Manuals. These manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific Chrysler group vehicles. Included - 2007 Chrysler Crossfire | Owner Manual - Page 287
in each category is shown on the sidewall of the tires on your car. All Passenger Car Tires Must Conform to Federal Safety Requirements in Addition to These Grades. Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on - 2007 Chrysler Crossfire | Owner Manual - Page 288
and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory - 2007 Chrysler Crossfire | Owner Manual - Page 289
INDEX 10 - 2007 Chrysler Crossfire | Owner Manual - Page 290
Light ...118 Appearance Care ...246 Ashtrays and Lighter ...74 Automatic Door Locks ...13 Automatic Transmission ...149,244 Fluid and Filter Changes ...245 Fluid Level Check ...245 Fluid Type ...244 Special Additives ...246 Autostick ...152 Ball Joints ...234 Battery ...119,231 Saving Feature - 2007 Chrysler Crossfire | Owner Manual - Page 291
...135 Coin Holder ...75 Compact Disc (CD) Maintenance ...134 Console ...72 Contract, Service ...284 Converter, Catalytic ...198 Convertible ...62 Convertible Top ...62 Convertible Top Maintenance ...251 Convertible Top Manual Override ...211 Coolant (Antifreeze) ...239,280 Cooling System ...238 - 2007 Chrysler Crossfire | Owner Manual - Page 292
225,267 Oil Change Interval ...227 Oil Selection ...228 Exhaust Gas Caution ...55 Exhaust System ...237 Exterior Lights ...259 Filters Air Cleaner ...229 Air Conditioning ...280 Engine Fuel ...229 Engine Oil ...228 Fluid Capacities ...265,267 Fluid Leaks ...57 Fluid Level Checks Manual Transmission - 2007 Chrysler Crossfire | Owner Manual - Page 293
Maintenance ...235 Hood Release ...84 Hoses ...241 Ignition Key ...9 Wiring System (Spark Plug Wires) ...231 Illuminated Entry ...86 Infant Restraint ...48 Lens Cleaning ...250 Interior Appearance Care ...249 Introduction ...4 Jack Location ...200 Jack Operation ...195 Jump Starting ...203 Key-In - 2007 Chrysler Crossfire | Owner Manual - Page 294
...172 Lubrication, Body ...235 Maintenance Free Battery ...231 Maintenance Procedures ...225 Maintenance Schedules ...273 Malfunction Indicator Light (Check Engine) ...124,223 Manual Override, Convertible Top ...211 Manual, Service ...286 Manual Transmission ...147,245 Fluid Level Check ...245 - 2007 Chrysler Crossfire | Owner Manual - Page 295
...228 Materials Added to ...228 Recommendation ...228 Oil Filter, Selection ...228 Onboard Diagnostic System ...222,223 Overheating, Engine ...194 Owner's Manual (Operator Manual) ...286 Paint Care ...246 Parking Brake ...156 Passing Light ...90 Pets ...54 Pets, Transporting ...54 Power Outlet - 2007 Chrysler Crossfire | Owner Manual - Page 296
284 Service Manuals ...286 Shift Speeds ...147,148 Slippery Surfaces, Driving On ...205 Snow Chains (Tire Chains) ...183 Snow Tires ...184 Soft Top ...62 Spark Plugs ...229 Specifications ...265 Standing Lights ...87 Starting ...145 Cold Weather ...146 Emergency (Jump Starting) ...203 Engine Fails - 2007 Chrysler Crossfire | Owner Manual - Page 297
...56,175 Sizes ...167 Snow Tires ...184 Spinning ...178 Tread Wear Indicators ...179 Tow-Away Alarm ...19,210 Towing ...206 Disabled Vehicle ...206 Trailering ...192 Towing Eyes ...208 Traction ...205 Trailer Towing ...192 Transmission Automatic ...149,244 Fluid ...244 Manual ...147,245 Shifting - 2007 Chrysler Crossfire | Owner Manual - Page 298
298 INDEX Warnings and Cautions ...6 Warranty Information ...285 Washer, Adding Fluid ...236 Washing Vehicle ...247 Wheel Alignment and Balance ...181 Wheel and Wheel Trim Care ...248 Windows Power ...21 Windshield Defroster ... - 2007 Chrysler Crossfire | Owner Manual - Page 299
Running Lights (Where Applicable)Fog Lights (If Equipped)Standing LightsMULTIFUNCTION CONTROL LEVER Turn SignalsHeadlight Dimmer SwitchPassing LightWindshield Wipers And WasherMist FunctionTELESCOPING STEERING COLUMN TIRE PRESSURE MONITOR SYSTEM (if equipped) REAR SPOILER BRAKE ASSIST SYSTEM
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
 |
 |
TABLE OF CONTENTS
SECTION
PAGE
1
INTRODUCTION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
2
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
. . . . . . . . . . . . . . . . . . . . . . . . . . .
7
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
59
4
UNDERSTANDING YOUR INSTRUMENT PANEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
111
5
STARTING AND OPERATING
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
143
6
WHAT TO DO IN EMERGENCIES
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
193
7
MAINTAINING YOUR VEHICLE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
219
8
MAINTENANCE SCHEDULES
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
271
9
IF YOU NEED CONSUMER ASSISTANCE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
281
10
INDEX
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
289
1
2
3
4
5
6
7
8
9
10