2008 Chrysler Sebring Owner Manual Sedan
2008 Chrysler Sebring Manual
2008 Chrysler Sebring manual content summary:
- 2008 Chrysler Sebring | Owner Manual Sedan - Page 1
2008 OWNER' S MANUAL Sebring - 2008 Chrysler Sebring | Owner Manual Sedan - Page 2
This manual may install them on products previously manufactured. WARNING! Driving after drinking can lead to an accident. Your perceptions are less sharp, your reflexes are slower, and your judgment is impaired when you have been drinking. Never drink and then drive. Copyright © 2007 Chrysler - 2008 Chrysler Sebring | Owner Manual Sedan - Page 3
SECTION 1 2 3 4 5 6 7 8 9 10 TABLE OF CONTENTS PAGE INTRODUCTION ...3 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ...9 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ...81 UNDERSTANDING YOUR INSTRUMENT PANEL ...165 STARTING AND OPERATING ...259 WHAT TO DO IN EMERGENCIES ...351 MAINTAINING YOUR - 2008 Chrysler Sebring | Owner Manual Sedan - Page 4
- 2008 Chrysler Sebring | Owner Manual Sedan - Page 5
INTRODUCTION CONTENTS Ⅵ Introduction ...4 Ⅵ How To Use This Manual ...4 Ⅵ Warnings And Cautions ...6 Ⅵ Vehicle Identification Number ...6 Ⅵ Vehicle Modifications/Alterations ...7 1 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 6
carefully. Following the instructions and recommendations in this manual will help assure safe service, remember that your authorized dealer knows your vehicle best, has the factory-trained technicians and genuine Mopar parts, and is interested in your satisfaction. HOW TO USE THIS MANUAL - 2008 Chrysler Sebring | Owner Manual Sedan - Page 7
INTRODUCTION 5 1 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 8
bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is found on the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 9
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. 1 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 10
- 2008 Chrysler Sebring | Owner Manual Sedan - Page 11
TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS Ⅵ A Word About Your Keys ...12 ▫ Ignition Key Removal ...13 ▫ Key-In-Ignition Reminder ...14 ▫ Locking Doors With The Key ...15 Ⅵ Sentry Key ...15 ▫ Replacement Keys ...16 ▫ Sentry Key Programming ...17 ▫ General Information ...18 Ⅵ Security Alarm - 2008 Chrysler Sebring | Owner Manual Sedan - Page 12
Additional Transmitters ...25 ▫ Battery Replacement ...25 ▫ General Information ...26 Ⅵ Remote Start System - If Equipped ...27 ▫ How To Use Remote Start ...28 Ⅵ Door Locks ...29 ▫ Manual Door Locks ...29 ▫ Power Door Locks ...31 ▫ Child-Protection Door Lock System (Rear Doors) ...33 Ⅵ Power Windows - 2008 Chrysler Sebring | Owner Manual Sedan - Page 13
49 ▫ BeltAlert Programming ...49 ▫ Automatic Locking Mode ...50 ▫ Seat Belts And Pregnant Women ...51 ▫ Seat Belt Extender ...51 ▫ Supplemental Restraint System (SRS) - Airbag . .52 ▫ Airbag System Components ...53 ▫ Front Seat Airbag Features ...53 ▫ Airbag Deployment Sensors And Controls ...59 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 14
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS You can insert the double-sided keys into the locks with either side up. The authorized dealer that sold you your vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from - 2008 Chrysler Sebring | Owner Manual Sedan - Page 15
. The engine can be started and stopped, but the key cannot be removed until you obtain service. • For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power window switches, radio, hands-free system (if equipped), and power outlets will remain active for 45 seconds - 2008 Chrysler Sebring | Owner Manual Sedan - Page 16
Programmable Features)" under "Electronic Vehicle Information Center (EVIC)" in Section 4 of this manual. CAUTION! An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended. Key-In-Ignition Reminder Opening the driver - 2008 Chrysler Sebring | Owner Manual Sedan - Page 17
cylinder which is located in the driver's door only. You can insert the key with either side up. To lock the door, turn the key rearward. To unlock the door, turn the key forward. See "Maintenance Procedures" in Section 7 "Maintaining Your Vehicle" of this manual for door lock lubrication. SENTRY - 2008 Chrysler Sebring | Owner Manual Sedan - Page 18
remove Sentry Keys from the vehicle and lock all doors when leaving the vehicle unattended. NOTE: • The Sentry Key Immobilizer System is not compatible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems authorized dealer replacement of keys. - 2008 Chrysler Sebring | Owner Manual Sedan - Page 19
Immobilizer System serviced, bring all vehicle keys with you to the authorized dealer. Sentry Keyா Programming You can program new keys to the system , the Vehicle Security Alarm Indicator Light will begin to flash. Turn the ignition switch to the LOCK position and remove the second key. 4. Insert - 2008 Chrysler Sebring | Owner Manual Sedan - Page 20
dealer at the time of service to be reprogrammed. General Information The Sentry Key system complies with FCC rules part 15 and with RSS-210 of lights, taillights and the indicator light in the cluster will flash. Then the exterior lights will flash for another 15 minutes. Rearming Of The System: - 2008 Chrysler Sebring | Owner Manual Sedan - Page 21
To Arm The System: 1. Remove the keys from the ignition switch and get out of the vehicle. 2. Lock the doors by pressing the power door lock switch or the LOCK button on the Remote Keyless Entry (RKE) transmitter. NOTE: The system will not arm if you lock the doors with the manual door lock plungers - 2008 Chrysler Sebring | Owner Manual Sedan - Page 22
door, the alarm will sound. If this occurs, disarm the system. If the alarm system is armed and the battery becomes disconnected the system will remain armed when the battery is reconnected. The exterior lights (EVIC)" in Section 4 of this manual. The lights will fade to off after about 30 seconds - 2008 Chrysler Sebring | Owner Manual Sedan - Page 23
door courtesy lights do not turn on if the dimmer control is in the interior lights ON position (extreme top position). • The illuminated entry system need not be pointed at the vehicle to activate the system. NOTE: The line of transmission must not be blocked with metal objects. 2 Vehicle Key - 2008 Chrysler Sebring | Owner Manual Sedan - Page 24
door, or twice to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system (if equipped) will also turn on. Remote Key Unlock, Driver Door/All Doors 4 of this manual for details. • LOCK position, and the key removed. 4. Repeat these steps if - 2008 Chrysler Sebring | Owner Manual Sedan - Page 25
Lights with Lock," under ЉPersonal Settings (Customer Programmable Features)" under "Electronic Vehicle Information Center (EVIC)" in Section 4 of this manual the LOCK position, and the key removed. 4. Repeat these steps if you the Security Alarm. Opening a door with the Security Alarm activated - 2008 Chrysler Sebring | Owner Manual Sedan - Page 26
of this manual. TO LOCK THE DOORS Press and release the LOCK button on the transmitter to lock all doors. The turn signal lights will flash button on the transmitter with the ignition in the LOCK position, and the key removed. 4. Repeat these steps if you want to return this feature to its previous - 2008 Chrysler Sebring | Owner Manual Sedan - Page 27
frequency noises emitted by the system. PROGRAMMING ADDITIONAL TRANSMITTERS Refer to SENTRY KEY "Sentry Key Programming." If you do not have a programmed transmitter, contact your authorized dealer for details. BATTERY REPLACEMENT The recommended replacement battery is CR2032. NOTE: Perchlorate - 2008 Chrysler Sebring | Owner Manual Sedan - Page 28
of the transmitter apart. Make sure not to damage the seal during removal. 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To assemble the transmitter case - 2008 Chrysler Sebring | Owner Manual Sedan - Page 29
in the transmitter. The expected life of batteries is five years. 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, military base, and some mobile or CB radios. REMOTE START SYSTEM - IF EQUIPPED Remote start conveniently starts the engine from outside the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 30
PARK. • Doors closed. • Hood closed. • Trunk closed. • Hazard switch off. • Brake switch inactive (brake pedal not pressed). • Ignition key removed from ignition switch. • Battery at an . To Exit Remote Start Mode Without Driving The Vehicle Allow the engine to run for the entire 15-minute cycle. - 2008 Chrysler Sebring | Owner Manual Sedan - Page 31
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 To Exit Remote Start Mode And Drive The Vehicle Before the end of the 15-minute cycle, press and release the UNLOCK button on the RKE transmitter to unlock the doors and disarm the Vehicle Security Alarm (if equipped). Then, within 15 minutes, insert - 2008 Chrysler Sebring | Owner Manual Sedan - Page 32
. WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Unsupervised use of vehicle equipment may - 2008 Chrysler Sebring | Owner Manual Sedan - Page 33
remove the key from the ignition and lock all of the doors when leaving the vehicle unattended. POWER DOOR LOCKS A door lock switch is located on the driver and passenger door panel. Press this switch to lock or unlock the doors. Power Door Lock Switch 2 Automatic Door Locks - If Equipped The auto - 2008 Chrysler Sebring | Owner Manual Sedan - Page 34
and the vehicle speed returned to 0 mph (0 km/h). 3. The transmission is in NEUTRAL or PARK. 4. The driver door is opened. 5. The doors were not previously unlocked. 6. The vehicle speed is 0 mph (0 km/h). Automatic Unlock Doors On Exit Programming The Auto Unlock on Exit feature can be enabled or - 2008 Chrysler Sebring | Owner Manual Sedan - Page 35
TO KNOW BEFORE STARTING YOUR VEHICLE 33 NOTE: Use the Auto Unlock On Exit feature in accordance with local laws. CHILD-PROTECTION DOOR LOCK SYSTEM (REAR DOORS) The Rear Door Child-Protection Locks are located inside the rear edge of the door. Insert the tip of the ignition key or similar flat - 2008 Chrysler Sebring | Owner Manual Sedan - Page 36
engaged, move the lock plunger up (unlocked position), roll down the window, and open the door with the outside door handle. POWER WINDOWS POWER WINDOW SWITCHES The control on the driver's door has up-down switches that give you fingertip control of all four power windows. Auto Power Window Switch - 2008 Chrysler Sebring | Owner Manual Sedan - Page 37
controls on the driver and passenger door trim panels have an Auto Down feature. These switches are labeled AUTO to indicate this capability. Push the window switch past the first detent, release, and the window will go down automatically. To open the window part way, push the window switch to - 2008 Chrysler Sebring | Owner Manual Sedan - Page 38
either door will Remove the obstacle and use the window switch again to close the window. • Any impact due to rough road conditions may trigger the auto reverse function unexpectedly during autoclosure. If this happens, pull the switch lightly to the first detent and hold to close window manually - 2008 Chrysler Sebring | Owner Manual Sedan - Page 39
path before closing. RESET AUTO UP Anytime the vehicle battery goes dead, the Auto Up function will be disabled. To reactivate the Auto Up feature, pull the the driver's door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 40
from outside the vehicle. From inside the vehicle the trunk lid can be released by pressing the Trunk Release Button located next to the steering wheel on the instrument panel. The transmission must be in PARK before the switch will operate. NOTE: The gear selector lever must be in PARK for this - 2008 Chrysler Sebring | Owner Manual Sedan - Page 41
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 With the ignition ON, the word "deck" will display in place of the odometer display indicating that the trunk is open. The odometer display will reappear once the trunk is closed or if the trip button is depressed. With the key in the lock position or - 2008 Chrysler Sebring | Owner Manual Sedan - Page 42
your vehicle are the restraint systems. The following safety features are standard on all vehicles: • Three-point lap and shoulder belts for all seating positions • driver and new active-vent front passenger airbags • New active-vent front passenger airbags • Knee Bolsters for front seat occupants - 2008 Chrysler Sebring | Owner Manual Sedan - Page 43
rows for sedans - if equipped • Supplemental seat side (Thorax) airbags - if equipped • Front seat belt retractors incorporate pretensioners to enhance occupant protection by managing occupant energy during an impact event. • All seat belt systems (except the driver's) include Automatic Locking - 2008 Chrysler Sebring | Owner Manual Sedan - Page 44
in a motor vehicle should be belted at all times. Lap/Shoulder Belts All seating positions in your vehicle are equipped with lap/shoulder Belts. The belt webbing retractor will lock only during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you - 2008 Chrysler Sebring | Owner Manual Sedan - Page 45
your body and can take the forces of a collision the best. WARNING! • Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt. Follow these instructions to wear your seat belt safely - 2008 Chrysler Sebring | Owner Manual Sedan - Page 46
is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop, you could move too far - 2008 Chrysler Sebring | Owner Manual Sedan - Page 47
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 WARNING! • A belt that is worn under your arm is very dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren't as strong as - 2008 Chrysler Sebring | Owner Manual Sedan - Page 48
thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. WARNING! • A lap belt worn too high can - 2008 Chrysler Sebring | Owner Manual Sedan - Page 49
a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (bent - 2008 Chrysler Sebring | Owner Manual Sedan - Page 50
devices that are designed to remove slack from the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all size occupants, including those in child - 2008 Chrysler Sebring | Owner Manual Sedan - Page 51
the pretensioners are single use items. After a collision that is severe enough to deploy the airbags and pretensioners, both must be replaced. Enhanced Seat Belt Reminder System (BeltAlertா) If the occupied driver's seat belt has not been buckled within 60 seconds of starting the vehicle and if the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 52
this mode, the shoulder belt is automatically prelocked. However, the belt will still retract to remove any slack in the shoulder belt. The Automatic Locking Mode is available on all passenger-seating positions. Use the Automatic Locking Mode anytime a child safety seat is installed in a passenger - 2008 Chrysler Sebring | Owner Manual Sedan - Page 53
wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so that belt extender. This extender should be used only if the existing belt is not long enough. When it is not required, remove the extender, and stow it. 2 WARNING! Using a seat belt - 2008 Chrysler Sebring | Owner Manual Sedan - Page 54
YOUR VEHICLE Supplemental Restraint System (SRS) - Airbag This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver's front airbag is mounted in the center of the steering wheel. The passenger's front airbag is mounted in the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 55
- side mounted (Thorax) Airbags - If Equipped • Front Impact Sensors • Side Impact Sensors - If Equipped • Steering Wheel and Column • Instrument Panel • Seat Belt Reminder Light • Knee Impact Bolster • Front Seat Belt Pretensioners Front Seat Airbag Features The front airbag system has dual-stage - 2008 Chrysler Sebring | Owner Manual Sedan - Page 56
is controlled by the driver's seat position as well as impact severity. Use of special inflators, result in a very compact driver's side airbag. In addition to the small size, the inflating gasses exit through strategically placed vents, which direct the gas away from the occupant. Front Passenger - 2008 Chrysler Sebring | Owner Manual Sedan - Page 57
offer side-impact protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each airbag features inflated chambers place adjacent to the head of each outboard occupant that reduce the potential for side-impact head injuries. The curtains deploy downward - 2008 Chrysler Sebring | Owner Manual Sedan - Page 58
objects could be pushed into you, causing serious injury. Side Airbag Inflatable Curtains (SABIC) Location NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment. The system includes sensors adjacent to both front and rear seat occupants that are - 2008 Chrysler Sebring | Owner Manual Sedan - Page 59
airbag is located should remain free from any obstructions. • Do not attach cup holders or any other objects on or around the door. The inflating side airbag could drive the object into occupants, causing serious injury. Airbags inflate in moderate to high speed impacts. Along with seat belts - 2008 Chrysler Sebring | Owner Manual Sedan - Page 60
should wear their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. 4. If your vehicle has side Thorax airbags, do not lean against the door as airbags will inflate forcefully into the space - 2008 Chrysler Sebring | Owner Manual Sedan - Page 61
the steering wheel or instrument panel. • Side airbags also need room to inflate. Do not lean against the door. Sit upright in the center of the seat. Airbag Deployment Sensors And Controls Occupant Restraint Controller (ORC) The Occupant Restraint Controller System (ORC) is part of a Federally - 2008 Chrysler Sebring | Owner Manual Sedan - Page 62
to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away. Impact Sensors Two sensors, located on the front body structure, trigger airbag deployment in direct frontal impacts and aid - 2008 Chrysler Sebring | Owner Manual Sedan - Page 63
and calculate the proper airbag deployment. Do not aftermarket seat cover. • Do not add a secondary seat cover other than those approved by Chrysler/Mopar. • At no time should any supplemental restraint system (SRS) component or SRS related component or fastener be modified or replaced with any part - 2008 Chrysler Sebring | Owner Manual Sedan - Page 64
• Cuts off fuel to the engine, • Flashes hazard lights, • Turns on the interior lights which remain on as long as the battery has power or until the ignition key is removed, • Unlocks the doors automatically. If Deployment Occurs The airbag systems are designed to deploy when the Occupant Restraint - 2008 Chrysler Sebring | Owner Manual Sedan - Page 65
Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioners, and the front passenger seat belt retractor assembly replaced by an authorized dealer as soon as possible. Also, have the Occupant Restraint Controller System serviced as - 2008 Chrysler Sebring | Owner Manual Sedan - Page 66
adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper, vehicle body structure, or add aftermarket side steps or running boards. • It is dangerous to try to repair any part of the airbag system - 2008 Chrysler Sebring | Owner Manual Sedan - Page 67
, have an authorized dealer service the system immediately. • The AIRBAG light does not come on during the six to eight seconds when the ignition switch is first turned on. • The light remains on after the six to eight second interval. • The light comes on and remains on while driving. NOTE: If the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 68
VEHICLE 2. Under certain circumstances, EDR data may not be recorded (e.g., loss of battery power). In conjunction with other data gathered during a complete accident investigation, the electronic data may be used by Chrysler Corporation and others to learn more about the possible causes of crashes - 2008 Chrysler Sebring | Owner Manual Sedan - Page 69
the airbag system • Airbag disable light status (if equipped) • ЉTimeЉ of airbag deployment (in terms of ignition cycles and vehicle mileage) • Airbag deployment level (if applicable) • Impact acceleration and angle • Seat belt status • Brake status (service and parking brakes) • Accelerator status - 2008 Chrysler Sebring | Owner Manual Sedan - Page 70
size. There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner's manual vehicle by the lap/ shoulder belt or the LATCH child restraint anchorage system. • The infant carrier is only - 2008 Chrysler Sebring | Owner Manual Sedan - Page 71
the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this lap/shoulder belt. (Some booster seats are equipped with a front shield and are held in the vehicle by the lap portion.) 2 WARNING! • Improper installation can lead - 2008 Chrysler Sebring | Owner Manual Sedan - Page 72
and height limits. • Carefully follow the instructions that come with the restraint. If you install the restraint improperly, it may not work when you need it. • All passenger seating positions contain automatic locking retractors. However, any seat belt system will loosen with time, so check the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 73
position, but you must use the vehicle's seat belt at the center position. If your child restraints are not LATCH-compatible, you can only install the child restraints using the vehicle's seat belts. Please refer to "Installing the Child Restraint System" for typical installation instructions. 2 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 74
Seat LATCH Anchors Because the lower anchorages are to be introduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchorages will continue to have features for installation in vehicles using the lap or lap/shoulder belt. They will also - 2008 Chrysler Sebring | Owner Manual Sedan - Page 75
your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provided with the child restraint system. The rear seat lower anchorages are round bars, located at the rear of the seat cushion where it - 2008 Chrysler Sebring | Owner Manual Sedan - Page 76
and attach the tether strap to the anchorage, being careful to route the tether strap to provide the most direct path between the anchor backs as you remove slack in the strap. • When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not being used - 2008 Chrysler Sebring | Owner Manual Sedan - Page 77
the reach of an inquisitive child. Remind all children in the vehicle that the seat belts are not toys and should not be played with, and never leave your child unattended in the vehicle. 2 WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant - 2008 Chrysler Sebring | Owner Manual Sedan - Page 78
slack in the tether strap according to the child restraint manufacturer's instructions. Installing Child Restraints Using the Vehicle Seat Belt The passenger seat belts are equipped with Automatic Locking Retractors (ALRs), which are designed to keep the lap portion tight around the child restraint - 2008 Chrysler Sebring | Owner Manual Sedan - Page 79
trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt to wear the shoulder belt comfortably, and whose legs , should use the lap/shoulder belt in a rear seat. Make belt under an arm or behind their back. Transporting Pets Airbags - 2008 Chrysler Sebring | Owner Manual Sedan - Page 80
belts. ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your vehicle. Drive acceleration in low gear can be detrimental and should be avoided. The engine oil installed 7 of this manual. NON-DETERGENT OR should be considered as a normal part of the break-in and - 2008 Chrysler Sebring | Owner Manual Sedan - Page 81
condition, replace the belt. Airbag Light The light should come on and remain on for six to eight seconds as a bulb check when the ignition switch is first turned ON. If the LED is not lit during starting, have it checked. If the light stays on or comes on while driving, have the system checked by - 2008 Chrysler Sebring | Owner Manual Sedan - Page 82
panel. Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. In addition, if gasoline fumes are detected or fuel, power steering fluid, transmission fluid, or brake fluid leaks are suspected, the cause should be located and corrected - 2008 Chrysler Sebring | Owner Manual Sedan - Page 83
...85 ▫ Automatic Dimming Mirror - If Equipped ...86 ▫ Electric Remote-Control Mirrors ...87 ▫ Adjusting Sideview Mirrors ...88 ▫ Illuminated Vanity Mirrors - If Equipped ...89 Ⅵ Hands-Free Communication (UConnect) - If Equipped ...89 ▫ Operation ...91 ▫ Phone Call Features ...98 ▫ UConnect System - 2008 Chrysler Sebring | Owner Manual Sedan - Page 84
Voice Training ...120 Ⅵ Seats ...121 ▫ Manual Front Seat Adjustments ...121 ▫ Power Seats - Lights ...131 ▫ Map/Reading/Interior Lights ...131 ▫ Headlights, Parking Lights, Instrument Panel Lights ...132 ▫ Automatic Headlight System - If Equipped . . 133 ▫ Headlight Time Delay ...133 ▫ Passing Light - 2008 Chrysler Sebring | Owner Manual Sedan - Page 85
Setting ...143 ▫ To Accelerate For Passing ...144 Ⅵ Garage Door Opener - If Equipped ...144 ▫ Programming HomeLink ...146 ▫ Gate Operator/Canadian Programming ...148 ▫ Using HomeLink ...149 ▫ Reprogramming A Single HomeLink Button ...149 ▫ Security ...150 ▫ Troubleshooting Tips ...150 ▫ General - 2008 Chrysler Sebring | Owner Manual Sedan - Page 86
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Venting Sunroof - Express ...153 ▫ Closing Sunroof - Express ...153 ▫ Auto Sunroof (Express) With Anti-Pinch Protection - If Equipped ...153 ▫ Sunshade Operation ...153 ▫ Wind Buffeting ...153 ▫ Sunroof Maintenance ...154 ▫ Ignition Off Operation ... - 2008 Chrysler Sebring | Owner Manual Sedan - Page 87
85 MIRRORS INSIDE DAY/NIGHT MIRROR - IF EQUIPPED Adjust the mirror to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical mirror adjustment. Annoying headlight glare can be reduced by moving the small control under the mirror to the night - 2008 Chrysler Sebring | Owner Manual Sedan - Page 88
headlight glare from vehicles behind you. Push in the button on the face of the mirror to activate the dimming feature. Automatic Dimming Mirror - If Equipped 1 - Auto Mirror Sensor 2 - Driver Map Light Switch 3 - Auto Mirror On/Off Switch 4 - Passenger Map Light Switch 5 - Auto Mirror ON LED - 2008 Chrysler Sebring | Owner Manual Sedan - Page 89
wipe the mirror clean. ELECTRIC REMOTE-CONTROL MIRRORS Both of the outside mirrors can be adjusted by using the remote controls mounted on the driver's door panel. The rotary knob has three separate positions: L for the Left mirror; O for Off; and R for the Right mirror. Power Mirror Adjust Switch - 2008 Chrysler Sebring | Owner Manual Sedan - Page 90
outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle. WARNING! Vehicles and other objects seen another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in this convex mirror. Mirror Directions - 2008 Chrysler Sebring | Owner Manual Sedan - Page 91
your vehicle's audio system; the system will automatically mute your radio when using the UConnect system. NOTE: The UConnect system requires a cellular phone equipped with the Bluetooth ЉHands-Free Profile,Љ Version 0.96 or higher. See the UConnect website for supported phones. 3 Illuminated - 2008 Chrysler Sebring | Owner Manual Sedan - Page 92
THE FEATURES OF YOUR VEHICLE NOTE: For UConnect customer support, visit the following websites: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect • or call 1-877-855-8400 UConnect allows you to transfer calls between the system and your cellular phone as you enter or - 2008 Chrysler Sebring | Owner Manual Sedan - Page 93
Refer to your cellular service provider or the phone manufacturer for details. The UConnect system is fully integrated with the vehicle's audio system. The volume of the UConnect system can be adjusted either from the radio volume control knob or from the steering wheel radio control (right switch - 2008 Chrysler Sebring | Owner Manual Sedan - Page 94
) UConnect System to a Cellular Phone To begin using your UConnect system, you must pair your compatible Bluetooth enabled cellular phone. To complete the pairing process, you will need to reference your cellular phone Owner's Manual. The UConnect website may also provide detailed instructions - 2008 Chrysler Sebring | Owner Manual Sedan - Page 95
OF YOUR VEHICLE 93 The following are general phone to UConnect system pairing instructions: • Press the PHONE button to begin. • After example, if priority 3 and priority 5 phones are present in the vehicle, the UConnect system will use the priority 3 cellular phone when you make a call. You can - 2008 Chrysler Sebring | Owner Manual Sedan - Page 96
, refer to ЉAdd Names to Your UConnect Phonebook,Љ in this section. • The UConnect system will confirm the name and then dial the corresponding phone number, which may appear in the display of certain radios. Add Names to Your UConnect Phonebook NOTE: Adding names to the phonebook is recommended - 2008 Chrysler Sebring | Owner Manual Sedan - Page 97
Bluetooth..." The system is now ready to accept phonebook entries from your phone using the Bluetooth Object Exchange Profile (OBEX). Please see your phone Owner's Manual for specific instructions on how to send these entries from your phone. NOTE: • The phone handset must support Bluetooth OBEX - 2008 Chrysler Sebring | Owner Manual Sedan - Page 98
this case, the user must first disconnect or drop the Bluetooth connection to the UConnect system, and then send the address book entry via Bluetooth. Please see your phone Owner's Manual for specific instructions on how to drop the Bluetooth connection. • If the phonebook entry is longer than - 2008 Chrysler Sebring | Owner Manual Sedan - Page 99
Phonebook • Press the PHONE button to begin. • After the ЉReadyЉ prompt and the following beep, say ЉPhonebook Erase All.Љ • The UConnect system will ask you to verify that you wish to delete all the entries from the phonebook. • After confirmation, the phonebook entries will be deleted. • Note - 2008 Chrysler Sebring | Owner Manual Sedan - Page 100
accessed through the UConnect system. Check with your cellular service provider for the features that you have. Answer or Reject an Incoming Call - No Call Currently in Progress When you receive a call on your cellular phone, the UConnect system will interrupt the vehicle audio system, if on, and - 2008 Chrysler Sebring | Owner Manual Sedan - Page 101
your cell phone. Press the PHONE button to place the current call on hold and answer the incoming call. NOTE: The UConnect system compatible phones in the market today do not support rejecting an incoming call when another call is in progress. Therefore, the user can only answer an incoming call or - 2008 Chrysler Sebring | Owner Manual Sedan - Page 102
terminated by the far end, a call on hold may not become active automatically. This is cell phone-dependent. To bring the call back from hold on the UConnect system either until the call ends, or until the vehicle battery condition dictates cessation of the call on the UConnect system and transfer - 2008 Chrysler Sebring | Owner Manual Sedan - Page 103
UConnect system for a certain duration, after which the call is automatically transferred from the UConnect system to the mobile phone. • An active call is automatically phone and manually dial the emergency number for your area. If the phone is not reachable and the UConnect system is operational - 2008 Chrysler Sebring | Owner Manual Sedan - Page 104
OF YOUR VEHICLE • After the ЉReadyЉ prompt and the following beep, say ЉEmergencyЉ and the UConnect system will instruct the paired cellular phone to call the emergency number. This feature is only supported in the U.S. NOTE: The emergency number dialed is based on the country where the vehicle is - 2008 Chrysler Sebring | Owner Manual Sedan - Page 105
phone keypad while navigating through an automated telephone system. You can use your UConnect system to access a voice mail system or an automated service, such as a paging service or automated customer service line. Some services require immediate response selection. In some instances, that - 2008 Chrysler Sebring | Owner Manual Sedan - Page 106
such as the instrument panel cluster, and supported by your cell phone, the UConnect system will provide notification to inform you of your battery strength, etc. Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnect system - 2008 Chrysler Sebring | Owner Manual Sedan - Page 107
if you dial the number using voice recognition. NOTE: Certain brands of mobile phones do not send the dial ring to the UConnect system to play it on the vehicle audio system, so you will not hear it. Under this situation, after successfully dialing a number the user may feel that the call did not - 2008 Chrysler Sebring | Owner Manual Sedan - Page 108
at a time. If you would like to connect or disconnect the Bluetooth connection between a UConnect paired cellular phone and the UConnect system, follow the instructions described in your cellular phone User's Manual. List Paired Cellular Phone Names • Press the PHONE button to begin. • After the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 109
to delete. Things You Should Know About Your UConnectா System UConnect Tutorial To hear a brief tutorial of the system features, press the PHONE button and say "UConnect Tutorial." Voice Training For users experiencing difficulty with the system recognizing their voice commands or numbers, the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 110
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Repeat the words and phrases when prompted by the UConnect system. For best results, the Voice Training session should be completed when the vehicle is parked with the engine running, all windows closed, and the blower - 2008 Chrysler Sebring | Owner Manual Sedan - Page 111
international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported. • In a convertible vehicle, system performance may be compromised with the convertible top down. Far End Audio Performance • Audio quality is maximized under: • low-to - 2008 Chrysler Sebring | Owner Manual Sedan - Page 112
sometimes be reduced by lowering the in-vehicle audio volume. • In a convertible vehicle, system performance may be compromised with the convertible top Link Cellular phones have been found to lose connection to the UConnect system. When this happens, the connection can generally be re-established - 2008 Chrysler Sebring | Owner Manual Sedan - Page 113
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 3 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 114
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE - 2008 Chrysler Sebring | Owner Manual Sedan - Page 115
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 3 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 116
VEHICLE Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all Voice Commands Alternate(s) Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home - 2008 Chrysler Sebring | Owner Manual Sedan - Page 117
mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again redial Voice Commands Alternate(s) pairing phone book Voice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up - 2008 Chrysler Sebring | Owner Manual Sedan - Page 118
FEATURES OF YOUR VEHICLE General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry rapid speaking or a raised voice level. WARNING! Any voice commanded system should be used only in safe driving conditions and all attention should be kept on the roadway ahead. - 2008 Chrysler Sebring | Owner Manual Sedan - Page 119
system, you should speak clearly and at a normal speaking volume. The system will best recognize your speech if the windows are closed, and the heater/air System understands two types of commands. Global commands are available at all times. Local commands are available if the supported radio - 2008 Chrysler Sebring | Owner Manual Sedan - Page 120
3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the voice recognition system is speaking. Please note the volume setting for VR is different then the audio system. Main Menu Start a dialogue by pressing the VR hard-key. You may say MAIN MENU to switch to - 2008 Chrysler Sebring | Owner Manual Sedan - Page 121
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Satellite Radio To switch to satellite radio mode say SAT or SATELLITE RADIO. In this mode, you may say the following commands: • CHANNEL NUMBER (to change the channel by its spoken number) • NEXT CHANNEL (to select the next channel) • PREVIOUS - 2008 Chrysler Sebring | Owner Manual Sedan - Page 122
once you are in that menu then speak "Voice Training." This will train your own voice to the system and will improve recognition. 2. Repeat the words and phrases when prompted by the UConnect System. For best results, the Voice Training session should be completed when the vehicle is parked, engine - 2008 Chrysler Sebring | Owner Manual Sedan - Page 123
VEHICLE 121 SEATS Manual Front Seat Adjustments Forward/Rearward The manual seat adjustment bar is at the front of the seat, near the floor. Pull the bar upward to move the seat forward or rearward. Release the bar once the seat is in the position desired. Then, using body pressure, move forward - 2008 Chrysler Sebring | Owner Manual Sedan - Page 124
sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. Driver Seat Manual Height Adjuster - If Equipped A lever style height adjustment feature enhances comfort for petite - 2008 Chrysler Sebring | Owner Manual Sedan - Page 125
position. WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. • Do not ride with the seatback - 2008 Chrysler Sebring | Owner Manual Sedan - Page 126
allows you to increase or decrease the amount of lumbar support. The control lever is located on the outboard side of the driver's seatback. Turn the control lever downward to increase and upward to decrease the desired amount of lumbar support. Power Seats - If Equipped The power seat switches are - 2008 Chrysler Sebring | Owner Manual Sedan - Page 127
up on the head restraint. To lower, depress the button on the post guide and push down on the head restraint. 3 WARNING! • Adjusting a seat sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only - 2008 Chrysler Sebring | Owner Manual Sedan - Page 128
and passenger seats. The controls for the heated seats are located in the center console above the climate controls. There are indicator lights in the switches, which indicate a low heat setting (one light lit) or high heat setting (two lights lit). Heated Seat Switches Press the switch once to - 2008 Chrysler Sebring | Owner Manual Sedan - Page 129
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 WARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater. It may - 2008 Chrysler Sebring | Owner Manual Sedan - Page 130
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The hard seatback features a work surface and a molded rim for retaining items stored on the seatback panel. Folding Rear Seat To provide additional storage area, the rear seatback can be folded forward. Pull on the loops shown in the picture to fold - 2008 Chrysler Sebring | Owner Manual Sedan - Page 131
not be used as a play area by children. They could be seriously injured in an accident. Children should be seated and using the proper restraint system. Folding Rear Seat Center Armrest The rear seat is equipped with a folding armrest with cupholders. 3 Folding Rear Seat Armrest - 2008 Chrysler Sebring | Owner Manual Sedan - Page 132
AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel. Then lift the secondary latch located under the front edge of the hood, near the center and raise the hood. Hood Safety Catch Hood - 2008 Chrysler Sebring | Owner Manual Sedan - Page 133
vision. You could have a collision. Be sure all hood latches are fully latched before driving. 3 LIGHTS Map/Reading/Interior Lights These lights are mounted between the sun visors above the rear view mirror. Each light is turned ON by pressing the button. Press the button a second time to turn - 2008 Chrysler Sebring | Owner Manual Sedan - Page 134
is a second light located midway back in the headliner. To protect the battery, the interior lights will turn off automatically 10 minutes after the ignition switch is moved to the LOCK position. This will occur if the interior lights were switched on manually or are on because a door is open. This - 2008 Chrysler Sebring | Owner Manual Sedan - Page 135
- If Equipped Turning the end of the Multifunction Control Lever to the third detent, "A" (Auto), will activate the automatic headlight system. With the engine running and the Multifunction Control Lever in the "A" (Auto) position, the headlights will turn on and turn off based on the surrounding - 2008 Chrysler Sebring | Owner Manual Sedan - Page 136
turned OFF, a chime will sound to alert the driver when the driver's door is opened. Fog Lights - If Equipped The front fog light switch is on the Multifunction Control Lever. To activate the front fog lights, turn on the parking lights or the low beam headlights and pull out the end of the control - 2008 Chrysler Sebring | Owner Manual Sedan - Page 137
up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. You can signal a lane change by moving the lever partially up or down without moving beyond the detent. 3 Front Fog - 2008 Chrysler Sebring | Owner Manual Sedan - Page 138
flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the fuse or indicator bulb is operated by a switch on the control lever. The lever is located on the right side of the steering column. - 2008 Chrysler Sebring | Owner Manual Sedan - Page 139
position again. 3 CAUTION! • Turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the the intermittent settings for High-speed wiper operation. • Always remove any buildup of snow that prevents the windshield wiper blades from - 2008 Chrysler Sebring | Owner Manual Sedan - Page 140
from a minimum of one cycle every second to a maximum of approximately 18 seconds between cycles. For vehicles equipped with the Speed Sensitive Intermittent Wiper System, the wiper delay times depend on vehicle speed. If the vehicle is moving less than 10 mph (16 km/h), delay times will double - 2008 Chrysler Sebring | Owner Manual Sedan - Page 141
Multifunction Control Lever (on the left side of the steering column) is placed in the A AUTO position. In addition, the headlights will turn OFF when the wipers are turned off if they Programmable Features)" under "Electronic Vehicle Information Center" in Section 4 of this manual. 3 Mist Control - 2008 Chrysler Sebring | Owner Manual Sedan - Page 142
then turn OFF. Adding Washer Fluid The fluid reservoir for the windshield washers is located in the engine compartment. Be sure to check the fluid level in the reservoir at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few - 2008 Chrysler Sebring | Owner Manual Sedan - Page 143
the control handle inward until fully engaged. WARNING! Do not adjust the steering wheel while driving. The telescoping adjustment must be locked while driving. Adjusting the steering wheel while driving or driving without the telescoping adjustment locked could cause the driver to lose control of - 2008 Chrysler Sebring | Owner Manual Sedan - Page 144
on the right side of the steering wheel. TO ACTIVATE: Push in and release the ON/OFF button located in the end of the Electronic Speed Control Lever. The Speed Control indicator in the instrument cluster will illuminate. To turn the system OFF, push in and release the ON/OFF button a second time - 2008 Chrysler Sebring | Owner Manual Sedan - Page 145
speed and on level ground before pushing downthe SET DECEL lever. TO DEACTIVATE: A soft tap on the brake pedal, pulling the speed control lever toward you CANCEL, or normal brake pressure while slowing the vehicle will deactivate speed control without erasing the set speed memory. Pushing in the ON - 2008 Chrysler Sebring | Owner Manual Sedan - Page 146
to drive without speed control. GARAGE DOOR OPENER - IF EQUIPPED HomeLink replaces up to three remote controls (handheld transmitters) that operate devices such as garage door openers, motorized gates, lighting, or home security systems. The HomeLink unit operates off your vehicle's battery - 2008 Chrysler Sebring | Owner Manual Sedan - Page 147
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 The HomeLink buttons that are located in the headliner or sun visor designate the three different HomeLink channels. WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 148
new battery be placed in the hand- transmission of the radio-frequency signal. Your vehicle should be parked outside of the garage when programming. 1. Turn the ignition switch to the ON/RUN position. 2. Hold the battery slow to a rapidly blinking light, then release both the HomeLink - 2008 Chrysler Sebring | Owner Manual Sedan - Page 149
seconds, and then turns to a constant light, continue with programming for a Rolling Code. 5. PROGRAMMING A ROLLING CODE SYSTEM At the garage door opener motor (in the garage), locate the "Learn" or "Training" button. This can usually be found where the hanging antenna wire is attached to the garage - 2008 Chrysler Sebring | Owner Manual Sedan - Page 150
third time (for two seconds) to complete the training. If you have any problems, or require assistance, please call toll-free 1-800-355-3515 or, on of transmission - which may not be long enough for HomeLink to pick up the signal during programming. Training The Garage Door Opener 1 - Door Opener - 2008 Chrysler Sebring | Owner Manual Sedan - Page 151
of the garage door or gate motor. If you are having difficulties programming a garage door opener or a gate operator, replace "Programming HomeLink" for the trained device (i.e., garage door opener, gate operator, Security system, entry door lock, home/office lighting, etc. The hand-held transmitter - 2008 Chrysler Sebring | Owner Manual Sedan - Page 152
when the Vehicle Security Alarm is active. Troubleshooting Tips If you are having trouble programming HomeLink, here are some of the most common solutions: • Replace the battery in the original transmitter. • Press the "Learn" button on the Garage Door Opener to complete the training for a Rolling - 2008 Chrysler Sebring | Owner Manual Sedan - Page 153
were met. POWER SUNROOF - IF EQUIPPED The sunroof controls are mounted between the sun visors in the Dome/Reading Lamp. 3 Power Sunroof Switch 1 - Left Interior Light 2 - Power Sunroof Switch 3 - ATC Sensor - If Equipped 4 - Right Interior - 2008 Chrysler Sebring | Owner Manual Sedan - Page 154
to operate the sunroof. Never allow fingers or other body parts, or any object to project through the sunroof opening. Injury may result. Opening Sunroof - Manual Press the switch rearward and hold, and the sunroof will open automatically from any position. The sunroof will open fully, then - 2008 Chrysler Sebring | Owner Manual Sedan - Page 155
automatically. This is called Express Close. During Express Close operation, any movement of the sunroof switch will stop the sunroof. Auto object. Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot - 2008 Chrysler Sebring | Owner Manual Sedan - Page 156
non-abrasive cleaner and a soft is turned off. Opening either front door will cancel this feature. For vehicles equipped (EVIC)" in Section 4 of this manual. ELECTRICAL POWER OUTLETS There are two 12 a fuse. The instrument panel power outlet, located below the climate control knobs, has power - 2008 Chrysler Sebring | Owner Manual Sedan - Page 157
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 3 Instrument Panel Power Outlet Console Interior The center console power outlet is powered directly from the battery (power available at all times). Items plugged into this outlet may discharge the battery and/or prevent engine starting. - 2008 Chrysler Sebring | Owner Manual Sedan - Page 158
, if plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly. Only use these intermittently and - 2008 Chrysler Sebring | Owner Manual Sedan - Page 159
also comes with a cigar lighter. You may use the power outlet, located in the instrument panel below the climate control knobs, or in the bottom slides forward from design position to provide added user comfort. Two cupholders can accommodate large sized fast food beverage containers, and 20 oz - 2008 Chrysler Sebring | Owner Manual Sedan - Page 160
allow use of cell phone while still plugged into the power outlet and with the armrest latched down. NOTE: The power outlet located inside the console can also energize the cigar lighter in the available Smoker's Package. 1 - Release Top Compartment 3 - Top Compartment 2 - Release Bottom Compart - 2008 Chrysler Sebring | Owner Manual Sedan - Page 161
VES™(Video Entertainment System) includes the following components: • The screen for a rear seat DVD player is stored under the armrest. • Remote Control • Audio/Video RCA Jacks 3 Video Console See Section Four, "Video Entertainment System-If Equipped," of this manual, for further information - 2008 Chrysler Sebring | Owner Manual Sedan - Page 162
the cupholder can keep cool beverages cool, and hot beverages hot. The rear cupholder heats to 140°F (60°C) or cools to 35°F (1.6°C). The switch is located on the front of the center console and has three positions: HEAT, OFF, COOL. When the unit is on and the LED is Red, the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 163
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 CAUTION! Make sure the beverage container can withstand the temperatures shown above, when using the Cooled or Heated Cupholder. Rear Bottle Holders There are built-in bottle holders located in both rear door trim panels. Rear Bottle Holder 3 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 164
in an accident. Children should be seated and using the proper restraint system. • To help protect against personal injury, passengers should not be seated only, not for passengers, who should sit in seats and use seat belts. STORAGE CARGO AREA The 60/40 split-folding rear seat provides cargo - 2008 Chrysler Sebring | Owner Manual Sedan - Page 165
as low and as far forward as possible. • Place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway. • Do not pile luggage or cargo higher than the top - 2008 Chrysler Sebring | Owner Manual Sedan - Page 166
- 2008 Chrysler Sebring | Owner Manual Sedan - Page 167
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Ⅵ Instrument Panel Features ...169 Ⅵ Base Instrument Cluster ...170 Ⅵ Premium Instrument Cluster ...171 Ⅵ Instrument Cluster Descriptions ...172 Ⅵ Electronic Vehicle Information Center (EVIC) - If Equipped ...183 ▫ Electronic Vehicle Information Center ( - 2008 Chrysler Sebring | Owner Manual Sedan - Page 168
...220 Ⅵ Sales Code REN - Multimedia System - If Equipped ...222 ▫ Operating Instructions - Satellite Radio (If Equipped) ...223 ▫ Operating Instructions - Voice Recognition System (VR) (If Equipped) ...223 ▫ Operating Instructions - Hands-Free Communication (UConnect) (If Equipped) ...224 ▫ Clock - 2008 Chrysler Sebring | Owner Manual Sedan - Page 169
UNDERSTANDING YOUR INSTRUMENT PANEL 167 Ⅵ Sales Code RER - Multimedia System - If Equipped ...225 ▫ Operating Instructions - Satellite Radio ...227 ▫ Operating Instructions - Hands-Free Communication (UConnect) (If Equipped) ...227 ▫ Clock Setting Procedure ...227 Ⅵ Universal Consumer Interface ( - 2008 Chrysler Sebring | Owner Manual Sedan - Page 170
...240 Ⅵ Radio Operation And Cellular Phones ...242 Ⅵ CD/DVD Disc Maintenance ...242 Ⅵ Climate Controls ...243 ▫ Manual Air Conditioning And Heating System ...243 ▫ Automatic Temperature Control (ATC) - If Equipped ...248 ▫ Operating Tips ...254 Ⅵ Rear Window Features ...258 ▫ Electric Rear - 2008 Chrysler Sebring | Owner Manual Sedan - Page 171
UNDERSTANDING YOUR INSTRUMENT PANEL 169 INSTRUMENT PANEL FEATURES 4 1 2 3 4 5 - Air Outlet - Side Window Demister Outlet - Instrument Cluster - Ignition Switch - Analog Clock 6 - Radio 7 - Passenger Airbag 8 - Glove Box 9 - Heated Seat Switch* 10 - Hazard Switch 11 - Storage Compartment 12 - - 2008 Chrysler Sebring | Owner Manual Sedan - Page 172
170 UNDERSTANDING YOUR INSTRUMENT PANEL BASE INSTRUMENT CLUSTER - 2008 Chrysler Sebring | Owner Manual Sedan - Page 173
UNDERSTANDING YOUR INSTRUMENT PANEL 171 PREMIUM INSTRUMENT CLUSTER 4 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 174
engine off immediately and call for service. There are steps that you can take to slow down an impending overheat condition. If your air conditioning is on, turn it off. The air conditioning system adds heat to the engine cooling system and turning off the A/C removes this heat. You can also turn - 2008 Chrysler Sebring | Owner Manual Sedan - Page 175
driving, turn off some of the vehicle's electrical devices, such as the Fog Lights or Rear Defroster. If the Charging System Light remains on, it means that the vehicle is experiencing a problem with the charging system. Obtain SERVICE IMMEDIATELY. See your local authorized dealer. 7. Airbag Light - 2008 Chrysler Sebring | Owner Manual Sedan - Page 176
system checked by an authorized dealer. If the light comes on and remains on while driving, accelerator to prevent engine damage. 13. Transmission Range Indicator This display indicator shows the automatic replacement, be sure to keep a record of the reading before and after the service so - 2008 Chrysler Sebring | Owner Manual Sedan - Page 177
off the "gASCAP" message. (Refer to "Onboard Diagnostic System - OBDII" in Section 7 of this manual for more information). If the problem continues, the message will appear the next time the vehicle is started. See your authorized dealer service center as soon as possible. Change Oil Your vehicle is - 2008 Chrysler Sebring | Owner Manual Sedan - Page 178
176 UNDERSTANDING YOUR INSTRUMENT PANEL indicator system is duty cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the ON position. To turn - 2008 Chrysler Sebring | Owner Manual Sedan - Page 179
Stability Program (ESP) Indicator Light/Traction Control System (TCS) Indicator Light - If Equipped If this indicator light flashes during acceleration, apply as little throttle as possible. While driving, ease up on the accelerator. Adapt your speed and driving to the prevailing road conditions - 2008 Chrysler Sebring | Owner Manual Sedan - Page 180
level conditions. The vehicle should have service performed, and the brake fluid level checked. If brake failure is indicated, immediate repair is necessary. WARNING! Driving a vehicle with the brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 181
. Anti-Lock Warning Light (ABS) This light monitors the ABS. This light will come on when the ignition key is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or comes on during driving, it indicates that the Anti-Lock portion of the brake system 4 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 182
BRAKE warning light is not on. If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefit of Anti-Lock Brakes. The ABS warning light . (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure - 2008 Chrysler Sebring | Owner Manual Sedan - Page 183
been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use aftermarket tire sealants or balance beads - 2008 Chrysler Sebring | Owner Manual Sedan - Page 184
to "Tire Pressure Monitor System (TPMS)" in Section 5 of this manual for more information). 25. Malfunction Indicator Light This light is part of an onboard diagnostic system called OBD that monitors emissions, engine, and automatic transaxle control systems. The light will illuminate when the key - 2008 Chrysler Sebring | Owner Manual Sedan - Page 185
) features a driver-interactive display. It is located in the lower left part of the cluster below the fuel and engine functions 4 EVIC Display Location • Audio mode displays - 12 preset Radio Stations or CD Title and Track number when playing • Tire Pressure Monitor System (TPMS) displays (if - 2008 Chrysler Sebring | Owner Manual Sedan - Page 186
Functions or Personal settings or to return to the default System status MENU display. Button Press and release the RESET Light Out (with a single chime) • Left Rear Turn Signal Light Out (with a single chime) • Right Front Turn Signal Light Out (with a single chime) • Right Rear Turn Signal Light - 2008 Chrysler Sebring | Owner Manual Sedan - Page 187
has sounded to indicate the next scheduled oil change interval. The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 188
YOUR INSTRUMENT PANEL 2. Fully depress the accelerator pedal slowly three times within 10 seconds. 3. Turn the ignition switch to the LOCK position. NOTE: If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary repeat this - 2008 Chrysler Sebring | Owner Manual Sedan - Page 189
When the DTE value is less than 30 mi (48 km) estimated driving distance, the DTE display will change to a text display of ЉLOW FUEL. This display will continue until the vehicle runs out of fuel. Adding a significant amount of fuel to the vehicle will turn off the LOW FUEL text - 2008 Chrysler Sebring | Owner Manual Sedan - Page 190
INSTRUMENT PANEL Automatic Compass Calibration This compass is self-calibrating, which eliminates the need to calibrate the compass manually. When release the RESET button and the "CAL" indicator will quit flashing. 5. Drive the vehicle slowly, completing one or more circles (in an area free from - 2008 Chrysler Sebring | Owner Manual Sedan - Page 191
the following procedure: NOTE: Magnetic materials and cell phones should be kept away from the top of the Instrument Panel. This is where the compass sensor is located. 4 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 192
(Refer to "Manual Compass Calibration" later in this section). Personal Settings (Customer Programmable Features) Personal settings allows the driver to set and recall features when the automatic transaxle is in PARK. Press and release the MENU button until "Personal Settings" displays in the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 193
191 Auto Unlock on Exit When ON is selected and the transaxle is in the PARK or NEUTRAL position, all doors will unlock when the driver's door is ON or OFF appears. Flash Lights with Lock When ON is selected, the front and rear turn signals will flash when the doors are locked or unlocked with - 2008 Chrysler Sebring | Owner Manual Sedan - Page 194
is selected, and the headlight switch is in the AUTO position, the headlights will turn on approximately 10 seconds brightness, refer to "Lights" in Section 3 of this manual. Key-Off Power Delay When this feature is selected, the power window switches, radio, hands-free system (if equipped), and - 2008 Chrysler Sebring | Owner Manual Sedan - Page 195
the analog clock, located at the top center disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the system, however, car radios have performance limitations, due to mobile operation and natural phenomena, which might lead you to believe your sound system - 2008 Chrysler Sebring | Owner Manual Sedan - Page 196
the ignition switch has been turned OFF, depending upon the ACCESSORY DELAY setting. Opening a vehicle front door will cancel this feature. SALES CODE RES - AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of your radio faceplate. RES - 2008 Chrysler Sebring | Owner Manual Sedan - Page 197
195 Operating Instructions - Radio increases the volume and to the left decreases it. When the audio system is turned on, the sound will be set at the same Voice Recognition System (Radio) - If Equipped Refer to "Voice Recognition System (VR)" in Section 3. Voice Recognition Button (UConnect Hands- - 2008 Chrysler Sebring | Owner Manual Sedan - Page 198
Section 3. If your vehicle is not equipped with or this feature is not available on your vehicle, a "Not Equipped With UConnect" message will display on the radio screen. TIME Button Press the TIME button and the time of day will display. In AM or FM mode, - 2008 Chrysler Sebring | Owner Manual Sedan - Page 199
UNDERSTANDING YOUR INSTRUMENT PANEL 197 INFO Button Press the INFO button for an RDS station (one with call letters displayed). The radio will return a Radio Text message broadcast from an FM station (FM mode only). RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to - 2008 Chrysler Sebring | Owner Manual Sedan - Page 200
None Adlt Hit Classicl Program Type Classic Rock College Country Foreign Language Information Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock 16-Digit Character Display Cls Rock College Country Language Inform Jazz News Nostalga Oldies Persnlty - 2008 Chrysler Sebring | Owner Manual Sedan - Page 201
UNDERSTANDING YOUR INSTRUMENT PANEL 199 Program Type Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather 16-Digit Character Display Soft Soft Rck Soft R&B Sports Talk Top 40 Weather SETUP Button Pressing the SETUP button allows - 2008 Chrysler Sebring | Owner Manual Sedan - Page 202
12 FM stations). DISC Button Pressing the DISC button will allow you to switch from AM/FM modes to Disc modes. Operation Instructions - CD MODE for CD and MP3 Audio Play NOTE: The ignition switch must be in the ON or ACC position to operate the radio. NOTE: This radio is capable - 2008 Chrysler Sebring | Owner Manual Sedan - Page 203
the CD player with the CD label facing up. The CD will automatically be pulled into the CD player and the CD icon will illuminate on This CD player will accept 4-3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels. These labels can - 2008 Chrysler Sebring | Owner Manual Sedan - Page 204
202 UNDERSTANDING YOUR INSTRUMENT PANEL If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the CD is not removed, the radio will reinsert the CD but will not play it. A disc can be ejected with the radio and ignition OFF. NOTE: Ejecting with ignition - 2008 Chrysler Sebring | Owner Manual Sedan - Page 205
to read files properly and may be unable to play the file normally. UDF and Apple HFS formats are not supported. The radio uses the following limits for file systems: • Maximum number of folder levels: 8 • Maximum number of files: 255 • Maximum number of folders. (The radio display of file names - 2008 Chrysler Sebring | Owner Manual Sedan - Page 206
MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit - 2008 Chrysler Sebring | Owner Manual Sedan - Page 207
UNDERSTANDING YOUR INSTRUMENT PANEL 205 Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files. Loading times for playback of MP3 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 208
to "Hands-Free Communication (UConnect)" in Section 3. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to "Satellite Radio" in this section. Operating Instructions - Video Entertainment System™ (VES) (If Equipped) Refer to separate "Video Entertainment System™ (VES) Guide." - 2008 Chrysler Sebring | Owner Manual Sedan - Page 209
AUX JACK) NOTE: The radio sales code is located on the lower right side of your radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must right increases the volume and to the left decreases it. When the audio system is turned ON, the sound will be set at the same volume - 2008 Chrysler Sebring | Owner Manual Sedan - Page 210
Section 3. If your vehicle is not equipped with or this feature is not available on your vehicle, a "Not Equipped With UConnect" message will display on the radio screen. TIME Button Press the TIME button and the time of day will display. In AM or FM mode, - 2008 Chrysler Sebring | Owner Manual Sedan - Page 211
UNDERSTANDING YOUR INSTRUMENT PANEL 209 3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save the time change - 2008 Chrysler Sebring | Owner Manual Sedan - Page 212
210 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the treble tones. Push the rotary TUNE/SCROLL control knob a fourth time and BALANCE will display. - 2008 Chrysler Sebring | Owner Manual Sedan - Page 213
UNDERSTANDING YOUR INSTRUMENT PANEL 211 Program Type Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues 16-Digit Character Display Jazz News Nostalga Oldies Persnlty Public R&B Rel Musc Rel Talk Rock Soft Soft - 2008 Chrysler Sebring | Owner Manual Sedan - Page 214
will switch subtitles to different subtitle languages that are available on the disc (if equipped). • Audio Stream - Repeatedly pressing SELECT will switch to different audio languages (if supported on the disc) (if equipped). • Angle - Repeatedly pressing SELECT will change the viewing angle if - 2008 Chrysler Sebring | Owner Manual Sedan - Page 215
knob to scroll up and down to select the number and then push to select. Audio Language - If Equipped Selecting this item allows you to choose a default audio language (effective only if the language is supported by the disc). You can select a language not listed by scrolling down and selecting - 2008 Chrysler Sebring | Owner Manual Sedan - Page 216
Audio DRC - If Equipped Selecting this item allows you to limit maximum audio box. AutoPlay - If Equipped When this is set to On and a DVD video is inserted, it will bypass the DVD menu screen and automatically play the movie. In some rare cases, the DVD player may not auto the disc supports the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 217
equipped) stations}. DISC Button Pressing the DISC button will allow you to switch from AM/FM modes to Disc modes. Operation Instructions - (DISC MODE for CD and MP3/WMA Audio Play, DVD-VIDEO) The radio DVD player and many DVD discs are coded by geographic region. These region codes must match in - 2008 Chrysler Sebring | Owner Manual Sedan - Page 218
This CD player will accept 4-3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. Eject Button - Ejecting Compact Disc(s) Press the and move to the entrance for easy removal. Radio display will show ЉEJECTING DISCЉ when the disc is being ejected and prompt - 2008 Chrysler Sebring | Owner Manual Sedan - Page 219
MP3/WMA file recording media and formats are limited. When writing MP3/WMA files, pay attention to the following restrictions. Supported Media (Disc Types) The MP3/WMA file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3,WMA, DVD Video, DVD-R, DVD-RW, DVD+R, DVD+RW, and CDDA - 2008 Chrysler Sebring | Owner Manual Sedan - Page 220
normally. UDF and Apple HFS formats are not supported. The radio uses the following limits for file systems: • Maximum number of directory levels: 8 problems. The radio is designed to recognize the file as an invalid MP3/WMA and will not play the file. When using the MP3/WMA encoder to compress audio - 2008 Chrysler Sebring | Owner Manual Sedan - Page 221
. In addition, variable bit rates (VBR) are also supported. The majority of MP3/WMA files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates. MPEG Specification MPEG-1 Audio Layer 3 MPEG-2 Audio Layer 3 WMA Specification WMA Sampling Frequency (kHz) 48, 44.1, 32 Bit Rate (kbps - 2008 Chrysler Sebring | Owner Manual Sedan - Page 222
to Љelapsed timeЉ display. Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3/WMA player, cassette player, or microphone and utilize the vehicle's audio system to amplify the source and play - 2008 Chrysler Sebring | Owner Manual Sedan - Page 223
proper level. If the AUX audio is not loud enough, turn the device's volume up. If the AUX audio sounds distorted, turn the device's Instructions - Voice Recognition System (VR) (If Equipped) For the radio, refer to "Voice Recognition System (VR)" in Section 3. For UConnect "Voice Recognition System - 2008 Chrysler Sebring | Owner Manual Sedan - Page 224
Communication (UConnect)" in Section 3. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to "Satellite Radio" in this section. Operating Instructions - Video Entertainment System (VES) (If Equipped) Refer to separate "Video Entertainment System (VES) Guide." Dolby Manufactured - 2008 Chrysler Sebring | Owner Manual Sedan - Page 225
your Radio-specific user's manual for detailed operating instructions. Operating Instructions - Voice Recognition System (VR) (If Equipped) For the radio, refer to "Voice Recognition System (VR)" in Section 3. For Hands Free Phone Communication (UConnect) "Voice Recognition System (VR)," refer to - 2008 Chrysler Sebring | Owner Manual Sedan - Page 226
Instructions - Hands-Free Communication (UConnectா) (If Equipped) Refer to "Hands-Free Communication (UConnect)" in Section 3. Clock Setting Procedure Setting the Clock 1. Turn on the multimedia system check mark will appear in the box next to the words "Daylight Savings." Touch the screen where - 2008 Chrysler Sebring | Owner Manual Sedan - Page 227
RER - MULTIMEDIA SYSTEM - IF EQUIPPED NOTE: The sales code is located on the lower right side of the unit's faceplate. The RER Multimedia system contains a radio, Sirius Satellite Radio player, navigation system, CD/DVD player, USB port, 20-gigabyte hard drive (HDD), and the UConnect Hands-Free - 2008 Chrysler Sebring | Owner Manual Sedan - Page 228
with an integrated color screen to provide maps, turn identification, selection menus, and instructions for selecting a variety of destinations and routes. A shared HDD for the navigation system, the database, and other radio features allows uploads of music and photos from CDs or through the USB - 2008 Chrysler Sebring | Owner Manual Sedan - Page 229
to your "Navigation User's Manual" for detailed operating instructions. Operating Instructions - Hands-Free Communication (UConnectா) (If Equipped) Refer to your "Navigation User's Manual" for detailed operating instructions. Clock Setting Procedure The GPS receiver in this system is synchronized to - 2008 Chrysler Sebring | Owner Manual Sedan - Page 230
setting. Setting the User Clock If you wish to set the clock to a time different from the system clock, you can manually adjust the time by performing the following: 1. Turn on the multimedia system. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen - 2008 Chrysler Sebring | Owner Manual Sedan - Page 231
UConnect. For sales code REN touch screen radio, refer to the separate User's Manual. This feature allows you to plug an iPod mobile digital device into the vehicle's sound system this feature, • the iPod audio can be played on the vehicle's sound system, providing metadata (Track Title, Artist - 2008 Chrysler Sebring | Owner Manual Sedan - Page 232
YOUR INSTRUMENT PANEL • the iPod battery charges when plugged into the UCI connector. Connecting The iPodா Device Use the optional connection cable to connect an iPod to the vehicle's UCI connector (which is located in the glove box on some vehicles. This location may vary with vehicle). Once the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 233
UNDERSTANDING YOUR INSTRUMENT PANEL 231 RW (Rewind) Button Press and hold the RW button to move backward in the current track. Holding the RW button long enough will take you back to the beginning of the current track. Pressing and releasing the RW button will go back five seconds of the current - 2008 Chrysler Sebring | Owner Manual Sedan - Page 234
and tracks on the iPod device. TUNE/SCROLL Knob In the List mode, the TUNE/SCROLL knob functions in a similar manner as the scroll wheel on the iPod. Turning the TUNE/SCROLL knob clockwise (forward) and counterclockwise (backward) scrolls through lists, displaying the track detail on the radio - 2008 Chrysler Sebring | Owner Manual Sedan - Page 235
you can follow the same steps to go to the desired track in that list. Not all iPod sub menu levels are available on this system. MUSIC TYPE Button The MUSIC TYPE button is another shortcut button to the genre listing on your iPod. 4 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 236
is pre-activated, and you may begin listening immediately to the one year of audio service that is included with the factory-installed satellite radio system in your vehicle. Sirius will supply a welcome kit that contains general information, including how to setup your on-line listening account - 2008 Chrysler Sebring | Owner Manual Sedan - Page 237
Antenna To ensure optimum reception, do not place items on the roof around the rooftop antenna location or strap items to the trunk lid around the trunk lid antenna tree coverage may interrupt reception in the form of short audio mutes. • Driving under wide bridges or along tall buildings can cause - 2008 Chrysler Sebring | Owner Manual Sedan - Page 238
236 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Satellite Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. SEEK Buttons Press and release the SEEK - 2008 Chrysler Sebring | Owner Manual Sedan - Page 239
tune to the preset channel. SETUP Button Pressing the SETUP button allows you to select the following items: • Display Sirius ID number - Press the AUDIO/ SELECT button to display the Sirius ID number. This number is used to activate, deactivate, or change the Sirius subscription. SET Button - To - 2008 Chrysler Sebring | Owner Manual Sedan - Page 240
(UConnect)" in Section 3. Operating Instructions - Video Entertainment System (VESா) (If Equipped) Refer to separate "Video Entertainment System (VES) Guide." REMOTE SOUND SYSTEM CONTROLS - IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel - 2008 Chrysler Sebring | Owner Manual Sedan - Page 241
volume and pressing the bottom of the switch will decrease the volume. The button located in the center of the right hand control will switch modes to Radio or the switch will SEEK down for the next listenable station. The button located in the center of the left hand control will tune to the next - 2008 Chrysler Sebring | Owner Manual Sedan - Page 242
240 UNDERSTANDING YOUR INSTRUMENT PANEL VIDEO ENTERTAINMENT SYSTEM (VES)ா - IF EQUIPPED The optional Video Entertainment System (VES) includes the following components for rear seat entertainment: • A diagonal 7 in (17.8 cm) Liquid Crystal Display (LCD) screen integrated into the center console - 2008 Chrysler Sebring | Owner Manual Sedan - Page 243
UNDERSTANDING YOUR INSTRUMENT PANEL 241 • A battery-powered infrared remote control snaps into a molded compartment in the center console armrest upper storage bin. 4 VES Remote Control • Two wireless infrared headsets allow rear seat passengers to listen to the same or individual audio sources. - 2008 Chrysler Sebring | Owner Manual Sedan - Page 244
Left audio in (white) 3. Right audio in (red) NOTE: Refer to your "Vehicle Entertainment System (VES) Users Manual" for detailed operating instructions. radio performance does not satisfactorily "clear" by the repositioning of the antenna, it is recommended that the radio volume be turned down or - 2008 Chrysler Sebring | Owner Manual Sedan - Page 245
not use solvents such as benzine, thinner, cleaners, or antistatic sprays. 5. Store the disc size or have irregular shapes. CLIMATE CONTROLS The Air Conditioning and Heating System is designed to make you comfortable in all types of weather. Manual Air Conditioning and Heating System 4 The Manual - 2008 Chrysler Sebring | Owner Manual Sedan - Page 246
amount of air forced through the ventilation system in any blue area of the scale indicates cooler temperatures while the rotating right into the red area indicates warmer temperatures. NOTE: If your air conditioning performance seems lower than expected, check the front of the A/C condenser: located - 2008 Chrysler Sebring | Owner Manual Sedan - Page 247
center instrument panel outlets can be aimed so that they are directed toward the rear seat passengers for maximum airflow to the rear. Bi-Level Air is directed through the panel and floor outlets. NOTE: For all settings except full cold or full hot, there is a difference in temperature between the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 248
air conditioning compressor operates in Mix and Defrost, or a blend of these modes, even if the Air Conditioning Snowflake button is not pressed. This dehumidifies the air flow of outside air from coming into the passenger compartment. A light will illuminate when the system is in recirculation mode - 2008 Chrysler Sebring | Owner Manual Sedan - Page 249
engage the Air Conditioning. A light will illuminate when the Air Conditioning System is engaged. Rotating the dial left into the blue area of the scale indicates cooler temperatures while the rotating right into the red area indicates warmer temperatures. NOTE: The air conditioning compressor will - 2008 Chrysler Sebring | Owner Manual Sedan - Page 250
to turn off the indicator light and the A/C compressor. Then, move the temperature control to the desired temperature. Automatic Temperature Control (ATC) - If Equipped Automatic Temperature Control Automatic Operation The Infrared Climate Control System automatically maintains the climate in the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 251
adjustment. You will experience the greatest efficiency by simply allowing the system to function automatically. Selecting the "O" (Off) position on the blower control stops the system completely and closes the outside air intake. 72°F (22°C) is the recommended setting for maximum comfort for the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 252
three times and then turn off. This indicates that the system is in AUTO mode and requesting the air conditioning is not necessary. • If your air conditioning performance seems lower than expected, check the front of the A/C condenser: located in front of the radiator, for an accumulation of dirt - 2008 Chrysler Sebring | Owner Manual Sedan - Page 253
UNDERSTANDING YOUR INSTRUMENT PANEL 251 4 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 254
AUTO mode setting to change airflow distribution by rotating the Mode Control knob (on the right) to one of the following positions. • Panel Air the rear seat passengers for maximum airflow to the rear. • Bi-Level Air is directed through the panel and floor outlets. NOTE: For all settings except - 2008 Chrysler Sebring | Owner Manual Sedan - Page 255
air conditioning. An LED in the button illuminates when manual compressor operation is selected. • Recirculation Control The system will automatically LED in the control button to illuminate. After ten minutes, the system will return to normal AUTO mode function and the LED will turn off. NOTE: • - 2008 Chrysler Sebring | Owner Manual Sedan - Page 256
. However, under certain conditions, while in Automatic Mode, the system is blowing air out the defrost vents. When these conditions antifreeze coolant in water is recommended. Refer to "Maintenance Procedures" in Section 7 of this manual for proper coolant selection. Winter Operation Use of the air - 2008 Chrysler Sebring | Owner Manual Sedan - Page 257
for about five minutes in the fresh air and high blower settings. This will insure adequate system lubrication to minimize the possibility of compressor damage when the system is started again. Window Fogging Interior fogging on the windshield can be quickly removed by turning the mode selector to - 2008 Chrysler Sebring | Owner Manual Sedan - Page 258
, but not eliminate, diesel and agricultural smells. The filter acts on air coming from outside the vehicle and recirculated air within the passenger compartment. Refer to "Maintenance Procedures" in Section 7 of this manual for A/C Air Filter service information or see your authorized dealer for - 2008 Chrysler Sebring | Owner Manual Sedan - Page 259
UNDERSTANDING YOUR INSTRUMENT PANEL 257 Control Setting Suggestions for Various Weather Conditions 4 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 260
Equipped The electric Rear Window Defroster Control is located on the climate control. Press this button the rear window defroster is ON. The defroster automatically turns off after approximately 10 minutes of operation or abrasive window cleaners on the interior surface of the window. Labels - 2008 Chrysler Sebring | Owner Manual Sedan - Page 261
Remote Start ...268 Ⅵ Engine Block Heater - If Equipped ...269 Ⅵ Automatic Transaxle ...270 ▫ Brake/Transaxle Interlock ...272 ▫ Automatic Transaxle Ignition Interlock System ...272 ▫ Electronically Controlled Automatic Transaxle ...273 Ⅵ AutoStick - If Equipped ...275 ▫ AutoStick Operation ...276 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 262
Brake System (ABS) - If Equipped ...285 ▫ Traction Control System (TCS) - If Equipped ...285 ▫ Brake Assist System (BAS) - If Equipped ...286 ▫ Electronic Stability Program (ESP) ...287 Ⅵ Power Steering ...290 Ⅵ Driving On Slippery Surfaces ...291 ▫ Acceleration ...291 ▫ Traction ...292 Ⅵ Driving - 2008 Chrysler Sebring | Owner Manual Sedan - Page 263
- If Equipped ...307 ▫ Limited Use Spare - If Equipped ...307 ▫ Tire Spinning ...308 ▫ Tread Wear Indicators ...309 ▫ Life Of Tire ...309 ▫ Replacement Tires ...310 ▫ Alignment And Balance ...312 Ⅵ Tire Chains ...312 Ⅵ Snow Tires ...312 Ⅵ Tire Rotation Recommendations ...313 Ⅵ Tire Pressure Monitor - 2008 Chrysler Sebring | Owner Manual Sedan - Page 264
▫ Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles ...330 ▫ Starting ...331 ▫ Cruising Range ...331 ▫ Replacement Parts ...331 ▫ Maintenance ...331 Ⅵ Adding Fuel ...332 ▫ Fuel Filler Cap (Gas Cap) ...332 ▫ Loose Fuel Filler Cap Message ...334 Ⅵ Vehicle Loading ...335 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 265
Weight ...342 ▫ Towing Requirements ...343 ▫ Towing Tips ...347 Ⅵ Recreational Towing (Behind Motorhome, Etc.) ...349 ▫ Towing This Vehicle Behind Another Vehicle (Flat Towing With All Four Wheels On The Ground) ...349 5 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 266
heat in the exhaust system, resulting in overheating and vehicle fire which may cause serious or fatal injuries. Automatic Transaxle The gear selector must be in the PARK or NEUTRAL position before you can start the engine. Apply the brakes before shifting to any driving gear. NOTE: You must - 2008 Chrysler Sebring | Owner Manual Sedan - Page 267
engine does not require pumping or depressing the accelerator pedal. Simply turn the ignition switch to get it started. Vehicles equipped with an automatic transaxle cannot be started this way. Unburned and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a - 2008 Chrysler Sebring | Owner Manual Sedan - Page 268
266 STARTING AND OPERATING Tip Start Feature - Automatic Transaxle Only Do not press the accelerator. Turn the ignition key briefly to START position, and release it. The starter motor will continue to run, but will automatically disengage itself when the engine is running. Extremely Cold Weather - 2008 Chrysler Sebring | Owner Manual Sedan - Page 269
or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. After Starting The idle speed will automatically decrease as the engine warms up. Remote Start System - If Equipped Remote start - 2008 Chrysler Sebring | Owner Manual Sedan - Page 270
insert the key into the ignition and turn the ignition to the RUN position. The ignition must be in the RUN position in order to drive the vehicle. NOTE: The engine can be started two consecutive times (two 15 minute cycles) by using the key fob. For a third cycle, the key - 2008 Chrysler Sebring | Owner Manual Sedan - Page 271
. The following conditions must be met before the engine will remote start: • Automatic Transaxle in Park • All doors are closed • Hood is closed • Hazard Switch is off • Brake Switch is inactive • Key is not in the ignition • Battery is at an acceptable charge level • Panic button on key fob is not - 2008 Chrysler Sebring | Owner Manual Sedan - Page 272
270 STARTING AND OPERATING AUTOMATIC TRANSAXLE CAUTION! Damage to the transaxle may occur if the following precautions are not observed: • Shift the gear speed. • Before shifting the gear selector lever into any gear, make sure your foot is firmly on the brake pedal. Automatic Gear Selector Lever - 2008 Chrysler Sebring | Owner Manual Sedan - Page 273
idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in REVERSE. You could lose control of the gear selector lever into PARK, remove the key from the ignition, and apply the parking brake. Once the key is removed from the ignition, the gear - 2008 Chrysler Sebring | Owner Manual Sedan - Page 274
equipment to determine if the problem could recur. AUTOMATIC TRANSAXLE IGNITION INTERLOCK SYSTEM This system prevents the key from being removed unless the gear selector lever is in PARK. It also prevents shifting out of PARK unless the key is in the ON position and the brake pedal is applied. - 2008 Chrysler Sebring | Owner Manual Sedan - Page 275
out of PARK. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. 5 WARNING! Never use PARK position on an Automatic Transaxle as a substitute for the parking brake. Always apply parking brake fully when parked to guard - 2008 Chrysler Sebring | Owner Manual Sedan - Page 276
, and best fuel economy. However, use the AutoStick mode and select the [5] range when frequent transaxle shifting occurs while using the DRIVE/OVERDRIVE range, such as when operating the vehicle under heavy loading conditions, (i.e., in hilly terrain, traveling into strong head winds or while - 2008 Chrysler Sebring | Owner Manual Sedan - Page 277
the problem could recur. If the transaxle cannot be reset, authorized dealer service is required. AUTOSTICKா - IF EQUIPPED AutoStick is a driver-interactive transaxle that offers six manual ratio changes to provide you with more control. AutoStick allows you to maximize engine braking, eliminate - 2008 Chrysler Sebring | Owner Manual Sedan - Page 278
trailer towing, and many other situations. AUTOSTICKா OPERATION By placing the gear selector lever one shift-level below the DRIVE position, it can be moved from side to side. This allows the driver to select a higher or lower range of gears. Moving the gear selector - 2008 Chrysler Sebring | Owner Manual Sedan - Page 279
powertrain cools off. • If the system detects a problem, it will disable the AutoStick mode and the transaxle will return to the automatic mode until the problem is corrected. PARKING BRAKE When the parking brake is applied with the ignition on, the Brake Light in the instrument cluster will come - 2008 Chrysler Sebring | Owner Manual Sedan - Page 280
278 STARTING AND OPERATING NOTE: If the light remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately. NOTE: If the parking brake is applied while the vehicle is moving, a chime will sound to alert the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 281
pull it upward until you feel resistance. To release the parking brake, grasp the handle and pull it slightly while pressing the button on the end of the handle. When the button drops into the handle (releasing the lock), guide the handle downward to its stop and then release the button and - 2008 Chrysler Sebring | Owner Manual Sedan - Page 282
WARNING! Never use PARK position on an automatic transaxle as a substitute for the parking brake. Always apply parking brake fully when parked to guard against vehicle movement , or move the vehicle. • Be sure the parking brake is fully disengaged before driving. Failure to do so can lead to - 2008 Chrysler Sebring | Owner Manual Sedan - Page 283
application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system. WARNING! WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot - 2008 Chrysler Sebring | Owner Manual Sedan - Page 284
vehicle checked immediately. ANTI-LOCK BRAKE SYSTEM (ABS) The Anti-Lock Brake System provides increased vehicle stability and brake performance under most braking conditions. The system automatically "pumps" the brakes during severe braking conditions to prevent wheel lock-up. WARNING! Pumping of - 2008 Chrysler Sebring | Owner Manual Sedan - Page 285
on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on. If the ABS light is on, the brake system should be serviced as - 2008 Chrysler Sebring | Owner Manual Sedan - Page 286
radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals. All vehicle wheels and tires must be the same size and type and tires must be properly inflated to produce accurate - 2008 Chrysler Sebring | Owner Manual Sedan - Page 287
manual for more information about ABS. Traction Control System (TCS) - If Equipped This system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration - 2008 Chrysler Sebring | Owner Manual Sedan - Page 288
situation by sensing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce braking distances. The BAS complements the Anti-Lock Brake System (ABS). Applying the brakes very quickly results in the best BAS assistance. To receive the benefit - 2008 Chrysler Sebring | Owner Manual Sedan - Page 289
AND OPERATING 287 Electronic Stability Program (ESP) This system enhances directional control and stability of the vehicle under various driving conditions. ESP corrects for over/under steering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the over/under - 2008 Chrysler Sebring | Owner Manual Sedan - Page 290
the vehicle is started the ESP system will be in this mode. This mode should be used for almost all driving situations. ESP should only be turned in the TCS section, has been disabled and the "ESP/TCS Indicator Light" will be illuminated. All other stability features of ESP function normally, with - 2008 Chrysler Sebring | Owner Manual Sedan - Page 291
wheel system, or both. If this light problem diagnosed and corrected. WARNING! In the Partial ESP mode, the engine torque reduction and stability features are desensitized. Therefore, the enhanced vehicle stability offered by ESP is unavailable. NOTE: To improve the vehicle's traction when driving - 2008 Chrysler Sebring | Owner Manual Sedan - Page 292
low vehicle speeds and during parking maneuvers. NOTE: Increased noise levels at the end of the steering wheel travel are considered normal and do not indicate that there is a problem with the power steering system. Upon initial start-up in cold weather, the power steering pump may make noise for - 2008 Chrysler Sebring | Owner Manual Sedan - Page 293
the front (driving) wheels. CAUTION! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur. WARNING! Rapid acceleration on slippery surfaces - 2008 Chrysler Sebring | Owner Manual Sedan - Page 294
2. Slow down if the road has standing water or puddles. 3. Replace the tires when tread wear indicators first become visible. 4. Keep the ensure safety and prevent damage to your vehicle. Flowing/Rising Water WARNING! Do not drive on, or cross, a road or a path where water is flowing and/or - 2008 Chrysler Sebring | Owner Manual Sedan - Page 295
cause damage to your vehicle's drivetrain components. Always inspect your vehicle's fluids (i.e., engine oil, transmission, axle, etc.) for signs of contamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water. Do not continue to operate the vehicle if any - 2008 Chrysler Sebring | Owner Manual Sedan - Page 296
driving through standing water. • Driving through standing water limits your vehicle's braking capabilities, which increases stopping distances. Therefore, after driving through standing water, drive slowly and lightly press on the brake (Passenger)-Metric tire sizing is based on U.S. design standards. - 2008 Chrysler Sebring | Owner Manual Sedan - Page 297
into the sidewall beginning with the section width. The letter ЉPЉ is absent from this tire size designation. Example: 215/65R15 96H • LT (Light Truck)-Metric tire sizing is based on U.S. design standards. The size designation for LT-Metric tires is the same as for P-Metric tires except for the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 298
296 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ؆...blank...؆ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall - 2008 Chrysler Sebring | Owner Manual Sedan - Page 299
STARTING AND OPERATING 297 EXAMPLE: Service Description: 95 = Load Index -A numerical code associated with the maximum a Standard Load (SL) Tire Extra Load (XL) = Extra Load (or Reinforced) Tire Light Load = Light Load Tire C,D,E = Load range associated with the maximum load a tire can carry at - 2008 Chrysler Sebring | Owner Manual Sedan - Page 300
TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted highway use. MA = Code representing the tire manufacturing location. (2 digits) L9 = Code representing the tire size. (2 digits) ABCD = Code used by tire - 2008 Chrysler Sebring | Owner Manual Sedan - Page 301
NOTE: The proper cold tire inflation pressure is listed on either the face of the driver's door or the driver's side "B" pillar. Tire and Loading Information Placard 5 B-PILLAR LOCATION This placard tells you important information about the: 1) number of people that can be carried in the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 302
if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the "Tire and Loading Information" placard and in the "Vehicle Loading" section of this manual. NOTE: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWR's) for the front and rear - 2008 Chrysler Sebring | Owner Manual Sedan - Page 303
from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity capacities of your vehicle with varying seating configurations and number and size of occupants. This table is for illustration purposes only and - 2008 Chrysler Sebring | Owner Manual Sedan - Page 304
302 STARTING AND OPERATING - 2008 Chrysler Sebring | Owner Manual Sedan - Page 305
that results in tire failure. • Unequal tire pressures can cause steering problems. You could lose control of your vehicle. • Over inflated or under can cause the vehicle to drift to the right or left. Always drive with each tire inflated to the recommended cold tire inflation pressure. TIRES- - 2008 Chrysler Sebring | Owner Manual Sedan - Page 306
in a need for earlier tire replacement. Underinflation also increases tire rolling resistance listed on either the face of the driver's door or the driver's side "B" pillar. Some Tire Pressure Information" section of this manual. B-PILLAR LOCATION The pressure should be checked and adjusted - 2008 Chrysler Sebring | Owner Manual Sedan - Page 307
by approximately 1 psi (7 kPa) per 12° F (7° C) of air temperature change. Keep this in mind when checking tire pressure inside a garage be too low. Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions - 2008 Chrysler Sebring | Owner Manual Sedan - Page 308
tires in sets of four (or 6, in case of trucks with dual rear wheels). Never combine them with other types of tires. Cuts and punctures in radial for radial tire repairs. WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to - 2008 Chrysler Sebring | Owner Manual Sedan - Page 309
tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time. WARNING! Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph (80 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 310
emergency use only. Installation of this limited use spare tire affects vehicle handling. With this tire, do not drive more than 60 mph (100 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited use spare tire and wheel assembly. Replace (or repair - 2008 Chrysler Sebring | Owner Manual Sedan - Page 311
the tread is worn to the tread wear indicators, the tire should be replaced. Many states have laws requiring tire replacement at this point. Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • Tire pressure • Distance driven 5 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 312
with as little exposure to light as possible. Protect tires from contact with oil, grease and gasoline. Replacement Tires The tires on size designation of your tire. The service description and load identification will be found on the original equipment tire. Failure to use equivalent replacement - 2008 Chrysler Sebring | Owner Manual Sedan - Page 313
311 WARNING! Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause - 2008 Chrysler Sebring | Owner Manual Sedan - Page 314
also cause the vehicle to pull to the left or right. Alignment will not correct this condition. See your dealer for proper diagnosis. Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance. Proper balancing will reduce vibration and avoid tire - 2008 Chrysler Sebring | Owner Manual Sedan - Page 315
. TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates suggested rotation method is the "forward-cross" shown in the following diagram. 5 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 316
and there should be no adjustment for this increased pressure. • The TPM System will warn the driver of a low tire pressure if the tire pressure falls . Once the low tire pressure warning (Tire Pressure Monitoring Telltale Light) illuminates, you must increase the tire pressure to the recommended - 2008 Chrysler Sebring | Owner Manual Sedan - Page 317
been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use aftermarket tire sealants or balance beads - 2008 Chrysler Sebring | Owner Manual Sedan - Page 318
the actual tire pressure in the tire. Base System - If Equipped The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings - 2008 Chrysler Sebring | Owner Manual Sedan - Page 319
: 1. Jamming due to electronic devices or driving next to facilities emitting the same Radio Frequencies as the TPM sensors. 2. Installing some form of aftermarket window tinting that affects radio wave signals. 3. Lots of snow or ice around the wheels or wheel housings. 4. Using tire chains on the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 320
for the TPMS to receive this information. Premium System - If Equipped The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings - 2008 Chrysler Sebring | Owner Manual Sedan - Page 321
319 • 3 Trigger Modules (mounted in three of the four wheel-wells) • Various Tire Pressure Monitoring System Messages, which display in the Electronic Vehicle Information Center (EVIC) • Tire Pressure Monitoring Telltale Light Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure - 2008 Chrysler Sebring | Owner Manual Sedan - Page 322
and the Tire Pressure Monitoring Telltale Light will flash on and off for 75 seconds and then remain on solid. In addition, the EVIC will display a ЉCHECK TPM SYSTEMЉ message for 3 seconds and then display dashes (- -) in place of the pressure value to indicate which sensor is not being received. - 2008 Chrysler Sebring | Owner Manual Sedan - Page 323
: 1. Jamming due to electronic devices or driving next to facilities emitting the same Radio Frequencies as the TPM sensors. 2. Installing some form of aftermarket window tinting that affects radio wave signals. 3. Lots of snow or ice around the wheels or wheel housings. 4. Using tire chains on the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 324
SYSTEMЉ message for 3 seconds and then display dashes (- -) in place of the pressure value. 5. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the compact spare, the TPMS will update automatically. In addition, the TPM Telltale Light part sensors - 2008 Chrysler Sebring | Owner Manual Sedan - Page 325
gasoline will not provide a benefit over high quality unleaded "regular" and "midgrade" gasolines, and in some circumstances may result in poorer performance. Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage - 2008 Chrysler Sebring | Owner Manual Sedan - Page 326
problems such as hard starting, stalling, and hesitations. If you experience these symptoms, try another brand of gasoline (with the appropriate octane rating for your engine) before considering service require the use of cleaner burning gasoline referred to air quality. The manufacturer supports - 2008 Chrysler Sebring | Owner Manual Sedan - Page 327
3.5L engine, DO NOT use gasoline containing Methanol or E85 Ethanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system components. NOTE: The 2.7L engine is now rated for E85 Ethanol use (EXCEPT CALIFORNIA EMISSION STATES). Only vehicles with the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 328
may require immediate service. Contact your dealer for service assistance. • The use of fuel additives, which are now being sold as octane enhancers is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from - 2008 Chrysler Sebring | Owner Manual Sedan - Page 329
, adjust the ventilation system to force fresh, outside air into the vehicle. • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows - 2008 Chrysler Sebring | Owner Manual Sedan - Page 330
Fuel vehicles only. This section only covers those subjects that are unique to these vehicles. Please refer to the other sections of this manual for information on features that are common between Flexible Fuel and gasoline only powered vehicles. E-85 Fuel Cap CAUTION! Only vehicles with the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 331
gasoline. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank. Do not use E-85 as a cleaning agent and never use it near an open - 2008 Chrysler Sebring | Owner Manual Sedan - Page 332
AND OPERATING For best results, a refueling pattern that alternates between E-85 and unleaded gasoline should be avoided. When starting and/or significant deterioration in drivability during warm up. NOTE: When the ambient temperature is above 90° F (32° C), you may experience hard starting and - 2008 Chrysler Sebring | Owner Manual Sedan - Page 333
driving range to decrease by about 30% compared to gasoline operation. Replacement Parts Many components in your Flexible Fuel Vehicle (FFV) are designed to be compatible with ethanol. Always be sure that your vehicle is serviced with correct ethanol compatible parts. CAUTION! Replacing fuel system - 2008 Chrysler Sebring | Owner Manual Sedan - Page 334
332 STARTING AND OPERATING ADDING FUEL Fuel Filler Cap (Gas Cap) As a reminder, a fuel icon with an arrow indicating which side of the vehicle the fuel filler door is located on, is located in the instrument cluster, just below the Fuel Gage. The gas cap is behind the fuel filler door, on the left - 2008 Chrysler Sebring | Owner Manual Sedan - Page 335
Malfunction Indicator Light to turn on. • To avoid fuel spillage and overfilling, do not "top off" the fuel tank after filling. When the fuel nozzle "clicks" or shuts off, the fuel tank is full. 5 Fuel Filler Door Features NOTE: If the gas cap is lost or damaged, be sure the replacement cap is - 2008 Chrysler Sebring | Owner Manual Sedan - Page 336
vehicle when the gas cap is removed or the tank filled. • problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the Malfunction Indicator Light (MIL). Resolving the problem - 2008 Chrysler Sebring | Owner Manual Sedan - Page 337
Your vehicle has a certification label attached to the rear of the driver's door. The label contains the following information: • Name of manufacturer • Month Gross Vehicle Weight Rating (GVWR) • Gross Axle Weight Rating (GAWR) front • Gross Axle Weight Rating (GAWR) rear • Vehicle Identification - 2008 Chrysler Sebring | Owner Manual Sedan - Page 338
hazards and shorten useful service life. Heavier axles or suspension components do not necessarily increase the vehicle's GVWR. WARNING! Because the front wheels steer the vehicle, it is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if - 2008 Chrysler Sebring | Owner Manual Sedan - Page 339
load your vehicle properly, first figure out its empty weight, axle by axle and side by side. Store heavier items down low and be sure you distribute their weight as evenly as possible. Stow all loose items securely before driving. If weighing the loaded vehicle shows that you have exceeded either - 2008 Chrysler Sebring | Owner Manual Sedan - Page 340
and safely as possible. To maintain warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing. If you have any questions or concerns after reviewing on a vehicle scale. The entire weight of the trailer must be supported by the scale. - 2008 Chrysler Sebring | Owner Manual Sedan - Page 341
axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR. WARNING! It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving load. You must consider this as part of the load on your vehicle. 5 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 342
supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the truck. These kinds of hitches are the most popular on the market today and they're commonly used to tow small- and medium-sized Class I - Light Duty 2,000 lbs - 2008 Chrysler Sebring | Owner Manual Sedan - Page 343
your given drivetrain. Engine/Transaxle 2.4L/Auto 2.7L/Auto 3.5L/Auto 1 Max. GTW (Gross Trailer Wt.) The trailer tongue weight must be considered as part of the combined weight of occupants and cargo, this manual. Please refer to the following website, http://www5.chrysler. automatic transaxle. 2 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 344
(GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to or trailer hitch. Consider the following items when computing the weight on the rear axle of the vehicle: • The tongue weight of the trailer. • The weight of - 2008 Chrysler Sebring | Owner Manual Sedan - Page 345
options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the Tire and Loading Information placard in the Tire Safety Information Section of this manual for the maximum combined weight of occupants and cargo for your vehicle. Towing Requirements - 2008 Chrysler Sebring | Owner Manual Sedan - Page 346
can cause a loss of control, poor performance, or damage to brakes, axle, engine, transaxle, steering, suspension, chassis structure, or tires. apply the parking brake on the tow vehicle. Put the tow vehicle automatic transaxle in P for Park. Always, block or ЉchockЉ the trailer wheels. • GCWR must - 2008 Chrysler Sebring | Owner Manual Sedan - Page 347
tires and for proper tire replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle's GVWR and GAWR limits. Towing Requirements - Trailer Brakes • Do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 348
trailer brakes to your vehicle's hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you accident. Towing Requirements - Trailer Lights & Wiring Whenever you pull a trailer, regardless of the trailer size, stoplights and turn signals on - 2008 Chrysler Sebring | Owner Manual Sedan - Page 349
harness to a trailer connector. 5 7-Pin Connector 4-Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping, and backing the trailer in an area located away from heavy traffic. Make sure all trailer and vehicle lights are working properly - including hazard flashers. - 2008 Chrysler Sebring | Owner Manual Sedan - Page 350
" in the "Maintenance Schedule" in this manual. NOTE: Check the four-speed automatic transaxle fluid level before towing. AutoStick six-speed transmission is sealed and the fluid level cannot be checked. See your authorized dealership service center for assistance. Electronic Speed Control (If - 2008 Chrysler Sebring | Owner Manual Sedan - Page 351
Driving Reduce speed. • Air Conditioning Turn off temporarily. • Refer to Cooling System Operating information in the Maintenance section of this manual ETC.) Towing This Vehicle Behind Another Vehicle (Flat towing with all four wheels on the ground) CAUTION! DO NOT flat tow this vehicle. Damage - 2008 Chrysler Sebring | Owner Manual Sedan - Page 352
- 2008 Chrysler Sebring | Owner Manual Sedan - Page 353
) ...355 Ⅵ Jacking And Tire Changing ...356 ▫ Jack Location ...356 ▫ Spare Tire Stowage ...356 ▫ Spare Tire Removal ...356 ▫ Preparations For Jacking ...357 ▫ Jacking Instructions ...358 Ⅵ Jump-Starting Procedures Due To A Low Battery ...364 Ⅵ Freeing A Stuck Vehicle ...367 Ⅵ Towing A Disabled - 2008 Chrysler Sebring | Owner Manual Sedan - Page 354
352 WHAT TO DO IN EMERGENCIES ▫ Towing This Vehicle Behind Another Vehicle With A Tow Dolly ...370 ▫ Without Power - Override Transaxle Interlock System ...370 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 355
EMERGENCIES 353 HAZARD WARNING FLASHER The flasher switch is located on the instrument panel, below the radio. Depress for service, the flasher system will continue to operate with the ignition key removed and the vehicle locked. NOTE: With extended use, the flasher may wear down your battery. IF - 2008 Chrysler Sebring | Owner Manual Sedan - Page 356
to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads "H", pull over and stop the vehicle with the engine at idle, when safe. Turn the air conditioner off and wait until the pointer - 2008 Chrysler Sebring | Owner Manual Sedan - Page 357
service center if your vehicle overheats. If you decide to look under the hood yourself, refer to Section 7, Maintenance, of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. Engine Oil Overheating - 2.4L Engine Only (If Equipped) During sustained high-speed driving - 2008 Chrysler Sebring | Owner Manual Sedan - Page 358
the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. Never start or run the lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. Jack Location The jack and jack - 2008 Chrysler Sebring | Owner Manual Sedan - Page 359
operating the jack or changing the wheel. • Turn on the Hazard Warning Flasher. • Block both the front and rear of the wheel diagonally opposite the jacking position. set the parking brake and place the gear selector in PARK (automatic transaxle) or REVERSE (manual transaxle). Turn OFF the ignition. - 2008 Chrysler Sebring | Owner Manual Sedan - Page 360
Warning Label • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Block the wheel diagonally opposite the wheel to be raised. • Set the parking brake firmly and set an automatic transmission in park; a manual transmission in reverse. - 2008 Chrysler Sebring | Owner Manual Sedan - Page 361
WHAT TO DO IN EMERGENCIES 359 WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Never start or run the engine with the vehicle on a jack. • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle - 2008 Chrysler Sebring | Owner Manual Sedan - Page 362
the jack with two attachment points. When the jack is partially expanded, the tension between the two attachment points holds the jack handle in place. Removing Jack Handle From Jack 2. Loosen, but do not remove, the wheel nuts by turning them to the left one turn while the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 363
WHAT TO DO IN EMERGENCIES 361 6 Jacking Locations - 2008 Chrysler Sebring | Owner Manual Sedan - Page 364
spare tire. Minimum tire lift provides maximum stability. 6. Remove the wheel nuts, and pull the wheel and wheel covers (where applicable) off the hub. Install the spare wheel and wheel nuts with the cone shaped end of the nuts toward the wheel. Lightly tighten the nuts. To avoid the risk of forcing - 2008 Chrysler Sebring | Owner Manual Sedan - Page 365
tightening the wheel nuts. Alternate nuts, until each nut has been tightened twice. Correct wheel nut torque is 100 ft. lbs (135 N·m). If you doubt that you have tightened the nuts correctly, have them checked with a torque wrench by your dealer or at a service station. 9. Remove the wheel blocks - 2008 Chrysler Sebring | Owner Manual Sedan - Page 366
BATTERY Jump-starting remote battery terminals are located under the hood. The battery is stored between the left front headlight assembly and the left front wheel your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way. Unburned fuel could enter the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 367
the vehicles to touch. Set parking brake, place automatic transaxle in PARK and turn ignition to LOCK for both vehicles. 3. Turn off the heater, radio, and all unnecessary electrical loads. 4. Remove the protective cover over the remote jumpstart positive battery post (+) in the engine compartment - 2008 Chrysler Sebring | Owner Manual Sedan - Page 368
in the vehicle with the discharged battery. 8. When removing the jumper cables, reverse the sequence exactly. Be careful of the moving belts and fan. 9. Reinstall the protective cover over the remote jumpstart positive battery post. WARNING! Jump-Starting Location 6. If the vehicle is equipped - 2008 Chrysler Sebring | Owner Manual Sedan - Page 369
manual for information on accessing the battery for service or replacement. WARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3. Damage to charging system - 2008 Chrysler Sebring | Owner Manual Sedan - Page 370
excessive wheel speeds may cause axle and tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle's wheels faster flat bed truck or with the front wheels off the ground. All Wheel Drive Your All Wheel Drive vehicle must be transported on a flat bed truck. CAUTION - 2008 Chrysler Sebring | Owner Manual Sedan - Page 371
use the accessories (wipers, alternative, a front end dolly must be used. Proper towing equipment is necessary to prevent damage to the vehicle. TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE (Flat towing with all four wheels on the ground) Flat towing of vehicles equipped with an automatic transmission - 2008 Chrysler Sebring | Owner Manual Sedan - Page 372
position. A dolly should be used under the front wheels if the rear wheels are raised. Proper towing equipment is necessary to prevent damage to the vehicle. Battery power is required to release the brake/transaxle interlock system. There is an override system that allows you to shift out of PARK in - 2008 Chrysler Sebring | Owner Manual Sedan - Page 373
Ⅵ Replacement Parts ...379 Ⅵ Authorized Dealer Service ...380 Ⅵ Maintenance Procedures ...380 ▫ Engine Oil ...380 ▫ Engine Oil Filter ...384 ▫ Drive Belt ...384 ▫ Spark Plugs ...385 ▫ Engine Air Cleaner Filter ...385 ▫ Catalytic Converter ...385 ▫ Maintenance-Free Battery ...387 ▫ Air Conditioner - 2008 Chrysler Sebring | Owner Manual Sedan - Page 374
...392 ▫ Body Lubrication ...392 ▫ Windshield Wiper Blades ...392 ▫ Windshield Washers ...393 ▫ Exhaust System ...393 ▫ Cooling System ...394 ▫ Hoses And Vacuum/Vapor Harnesses ...400 ▫ Fuel System ...400 ▫ Brake System ...400 ▫ Automatic Transaxle ...403 ▫ Front And Rear Wheel Bearings ...406 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 375
MAINTAINING YOUR VEHICLE 373 ▫ Tail/Stop Light, Rear Turn Signal Light, Backup Light ...424 ▫ License Plate Light ...427 ▫ Center High-Mounted Stop Light (CHMSL) ...428 Ⅵ Fluids And Capacities ...429 Ⅵ Fluids, Lubricants, And Genuine Parts ...430 ▫ Engine ...430 7 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 376
374 MAINTAINING YOUR VEHICLE 2.4L GAS ENGINE COMPARTMENT - 2008 Chrysler Sebring | Owner Manual Sedan - Page 377
MAINTAINING YOUR VEHICLE 375 2.7L GAS ENGINE COMPARTMENT 7 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 378
376 MAINTAINING YOUR VEHICLE 3.5L ENGINE COMPARTMENT 3.5L Engine - 2008 Chrysler Sebring | Owner Manual Sedan - Page 379
converter damage and power loss will soon occur. Immediate service is required. Loose Fuel Filler Cap Message After fuel is added, the vehicle diagnostic system can determine if the fuel filler cap is possibly loose or improperly installed. A "gASCAP" message will be displayed in the instrument - 2008 Chrysler Sebring | Owner Manual Sedan - Page 380
Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing. Normally, the OBD II system will be ready. The OBD II system may not be ready if your vehicle was recently serviced, recently had a dead battery, or a battery replacement - 2008 Chrysler Sebring | Owner Manual Sedan - Page 381
your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update. A recheck with the above test routine may then indicate - 2008 Chrysler Sebring | Owner Manual Sedan - Page 382
to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these Service manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems can result in - 2008 Chrysler Sebring | Owner Manual Sedan - Page 383
zone marked SAFE or a crosshatch zone marked with MIN at the low end of the range and MAX at the high end of the range. Adding one quart of oil when the reading is at the low end of the range marking will raise the oil level to the high end - 2008 Chrysler Sebring | Owner Manual Sedan - Page 384
you that it is time to take your vehicle in for scheduled maintenance. Refer to "Maintenance Schedule" in Section 8 of this manual for information on this system. NOTE: Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or 6 months, whichever occurs first. Engine Oil - 2008 Chrysler Sebring | Owner Manual Sedan - Page 385
shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to the "Engine Compartment" illustration in this section. Lubricants which do not have both met, and the recommended maintenance intervals for oil and filter changes are followed. 7 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 386
be used to assure most efficient service. Mopar Engine Oil Filters are high quality oil filters and are recommended. Drive Belt At the mileage indicated in section 8: "Maintenance Schedule", replace the drive belt with a new drive belt. NOTE: The belt must be routed correctly to ensure proper - 2008 Chrysler Sebring | Owner Manual Sedan - Page 387
manual for engine air cleaner filter maintenance intervals. NOTE: Be sure to follow the "dusty or off-road conditions" maintenance interval if applicable. WARNING! The air induction system (air cleaner, hoses, etc) can provide a measure of protection in the case of engine backfire. Do not remove - 2008 Chrysler Sebring | Owner Manual Sedan - Page 388
your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating. If this occurs, stop the vehicle, turn off the engine, and allow it to cool. Service, including - 2008 Chrysler Sebring | Owner Manual Sedan - Page 389
fender and is accessible without removing the tire and wheel. Remote battery terminals are located in the engine compartment for jump-starting. To access the battery, turn the steering wheel fully to the right and remove the inner fender shield. WARNING! • Battery fluid is a corrosive acid solution - 2008 Chrysler Sebring | Owner Manual Sedan - Page 390
as battery damage can result. Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt - 2008 Chrysler Sebring | Owner Manual Sedan - Page 391
approved A/C System Sealers, Stop Leak Products, Seal Conditioners, Compressor Oil, and Refrigerants. A/C Air Filter - If Equipped Refer to the "Maintenance Schedule" in Section 8 of this manual for A/C Air Filter service intervals. 7 WARNING! Do not remove the A/C Air Filter while the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 392
it. 4. Pivot the glove box downward. 5. Disengage the two retaining tabs that secure the filter cover to the HVAC housing and remove the cover. A/C Air Filter Replacement 6. Remove the A/C Air Filter by pulling it straight out of the housing. 7. Install the A/C Air Filter with the arrow on the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 393
airflow direction through the filter. Failure to install the filter properly will result in the need to replace it more often. 8. Reinstall the glove box door dampener and glove box. Power Steering - Fluid Check Checking the power steering fluid level at a defined service interval is not required - 2008 Chrysler Sebring | Owner Manual Sedan - Page 394
and all body pivot points, including seat tracks, door hinges, trunk hinges, and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust - 2008 Chrysler Sebring | Owner Manual Sedan - Page 395
blade packaging for specific installation instructions. Many wiper blade replacements fit multiple vehicles. Windshield Washers NOTE: Refer to the appropriate "Engine Compartment" diagram in Section 7 for the location of the windshield washer fluid reservoir. The fluid reservoir for the windshield - 2008 Chrysler Sebring | Owner Manual Sedan - Page 396
the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for an oil change or lubrication. Replace as required. Cooling System WARNING! • When working near the radiator cooling fan CO, refer to Exhaust Gas in the Safety Tips section of this manual. - 2008 Chrysler Sebring | Owner Manual Sedan - Page 397
with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of old antifreeze solution. Selection Of Coolant Use only the manufacturer's recommended coolant, refer to "Fluids, Lubricants, and Genuine Parts" for correct coolant type - 2008 Chrysler Sebring | Owner Manual Sedan - Page 398
If a non-HOAT coolant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible. • Do Additive Technology (HOAT) coolant. When adding coolant: • The manufacturer recommends using Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula - 2008 Chrysler Sebring | Owner Manual Sedan - Page 399
the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle. Personal injury or engine - 2008 Chrysler Sebring | Owner Manual Sedan - Page 400
the engine is cold. The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for coolant freeze point or replacing coolant. Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need - 2008 Chrysler Sebring | Owner Manual Sedan - Page 401
radiator and in the coolant recovery bottle. If antifreeze needs to be added, contents of coolant recovery bottle must also be air conditioning, keep the front of the condenser clean, also. • Do not change the thermostat for summer or winter operation. If replacement is ever necessary, install - 2008 Chrysler Sebring | Owner Manual Sedan - Page 402
nearest to high heat sources such as the exhaust manifold. Inspect hose routing to be sure hoses do not touch any heat source or moving system servicing. Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Suggested service - 2008 Chrysler Sebring | Owner Manual Sedan - Page 403
necessarily an indication of leakage. Actual dripping of hot fluid when systems are under pressure (during vehicle operation) should be noted before a hose is replaced based on leakage. • Inspect the brake hoses whenever the brake system is serviced and at every engine oil change. Inspect hydraulic - 2008 Chrysler Sebring | Owner Manual Sedan - Page 404
Cylinder - Brake Fluid Level Check Check the fluid level in the master cylinder immediately if the brake system warning light indicates system failure. Check the fluid level in the master cylinder when performing underhood services. Clean the top of the master cylinder area before removing the cap - 2008 Chrysler Sebring | Owner Manual Sedan - Page 405
causing partial or complete brake failure. Automatic Transaxle The automatic transaxle and differential assembly are contained within a single housing. The fluid level in the automatic transaxle should be checked whenever the vehicle is serviced. Operation with an improper fluid level will greatly - 2008 Chrysler Sebring | Owner Manual Sedan - Page 406
automatic transaxle fluid level properly: 1. Park the vehicle on level ground. 2. Run the engine at curb idle speed for a minimum of 60 seconds. 3. Apply the parking brake dirt entering the transaxle. 6. Remove the dipstick and determine if the fluid is hot or cold. Hot fluid is approximately 180° F - 2008 Chrysler Sebring | Owner Manual Sedan - Page 407
properly. Fluid and Filter Changes Change the automatic transaxle fluid and filter at the intervals shown in the "Maintenance Schedule" in this manual. In addition, change the fluid and filter if the transaxle is disassembled for any reason. Special Additives Automatic Transmission Fluid (ATF - 2008 Chrysler Sebring | Owner Manual Sedan - Page 408
wheel bearings are permanently sealed. No regular maintenance is required for these components. Appearance Care And Protection From Corrosion Protection Of Body And Paint from Corrosion Vehicle body care requirements vary according to geographic locations of deterioration or removal of paint and - 2008 Chrysler Sebring | Owner Manual Sedan - Page 409
your vehicle, use Mopar Super Kleen Bug and Tar Remover to remove. • Use Mopar Cleaner Wax to remove road film, stains and to protect your paint finish you drive near the ocean, hose off the undercarriage at least once a month. • It is important that the drain holes in the lower edges of the doors, - 2008 Chrysler Sebring | Owner Manual Sedan - Page 410
and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use Mopar touchup paint on scratches remove heavy soil and/or excessive brake dust, use Mopar Wheel Cleaner (05066247AB) or equivalent or select a nonabrasive, non-acidic cleaner. - 2008 Chrysler Sebring | Owner Manual Sedan - Page 411
, cleaning fluids, solvents, detergents, or ammonia-based cleaners to clean your leather upholstery. Application of a leather conditioner is not - If Equipped YES Essentials seats may be cleaned in the following manner: • Remove as much of the stain as possible by blotting with a clean, dry towel. - 2008 Chrysler Sebring | Owner Manual Sedan - Page 412
the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap the radio antenna. Do not use scrapers or other sharp instruments, which may scratch the elements. When cleaning the rear view mirror, spray cleaner on the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 413
dye, or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the car to wash them. Replace the belts if they appear frayed - 2008 Chrysler Sebring | Owner Manual Sedan - Page 414
the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini fuses. A label that identifies each component may be printed on the inside of the cover. Refer to the graphic below for FUSES/TIPM location. Fuse and Relay Center (TIPM) Cavity 1 2 Cartridge Mini - 2008 Chrysler Sebring | Owner Manual Sedan - Page 415
Stop Light (CHMSL)/Brake Switch Battery Feed - Ignition Switch Trailer Tow - If Equipped Ignition Off Draw (IOD) - Power Mirror Switch/Climate Controls Ignition Off Draw (IOD) Sense 1 Ignition Off Draw (IOD) Sense 2 Cavity Cartridge Mini Fuse Fuse 40 Amp Green 20 Amp Yellow 15 Amp Lt Blue 20 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 416
Draw (IOD) - Cabin Compartment Node (CCN)/ Interior Lighting Battery Feed - Radiator Fan Relay IGN Run/ACC - Cigar Lighter/PWR Sunroof Mod Battery Feed - Auto Shutdown (ASD) Relay Cavity 19 20 21 Cartridge Mini Fuse Fuse - - - 20 Amp Yellow 15 Amp Lt. Blue 10 Amp Red 10 Amp Red 15 Amp Lt. Blue 25 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 417
Cartridge Mini Fuse Description Fuse 15 Amp Auto Shutdown (ASD) - Lt. Blue Relay Feed 2 Ignition Run - Occupant Classification Auto Shutdown (ASD) - Pink Relay Feed 1 Battery Feed - Switch 10 Amp Bank/Diagnostic Link - Red Connector/Powertrain Control Module (PCM) Battery Feed - AntiLock Brakes (ABS - 2008 Chrysler Sebring | Owner Manual Sedan - Page 418
Cavity Cartridge Mini Fuse Fuse Description Battery Feed - AntiLock Brakes (ABS) Module - If Equipped/ Electronic Stability Program (ESP) Module - If Equipped Battery Feed - Passenger Door Module (PDM)/Driver Door Module (DDM) - CAUTION! • When installing the Totally Integrated Power Module cover - 2008 Chrysler Sebring | Owner Manual Sedan - Page 419
preserve your battery. You may: • Lights ...578/W5W Visor Vanity Lights ...A6220 Glove Box Light ...194 LIGHT BULBS - Interior Bulb Number Shift Indicator Light ...JKLE14140 Rear Compartment (Trunk) Light ...579 NOTE: For lighted switches, see your dealer for replacement instructions. LIGHTS - 2008 Chrysler Sebring | Owner Manual Sedan - Page 420
MAINTAINING YOUR VEHICLE BULB REPLACEMENT Headlight Bulb Replacement 1. Raise and prop open the hood. Locate the connector behind the headlight. NOTE: It may be necessary to remove the air cleaner filter housing and position the totally integrated power module aside prior to replacing the low beam - 2008 Chrysler Sebring | Owner Manual Sedan - Page 421
MAINTAINING YOUR VEHICLE 419 1 - High Beam Headlight 2 - Low Beam Headlight Twisting Bulb From Socket 3. Rotate bulb and connector one-quarter turn and pull outward from assembly. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. 7 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 422
and replace the bulb. Head Light Assembly Removal - Bulb Replacement 1. Raise and prop open the hood. Remove the headlight mounting screws. Removing Halogen Bulb -quarter turn to secure. Mounting Screw Location 2. Remove the push-in fasteners by prying under the head of the fasteners with - 2008 Chrysler Sebring | Owner Manual Sedan - Page 423
free the ball stud from its retainer in the fender. Pull the headlight assembly away from the vehicle. 4. Follow Steps 3 - 6 in the above "Headlight Bulb Replacement" section. 5. Reinstall Head Light Assembly by reversing steps 2 and 3 above. 7 Gently Pry Out Headlight - 2008 Chrysler Sebring | Owner Manual Sedan - Page 424
the headlight housing. 3. Remove the bulb from the connector socket and install the replacement bulb. 4. Install the bulb and connector assembly into the headlight housing and rotate the connector one-quarter turn clockwise to lock it in place. Front Fog Light NOTE: Access to the lights through the - 2008 Chrysler Sebring | Owner Manual Sedan - Page 425
YOUR VEHICLE 423 1. Rotate the bulb's electrical connector one-quarter turn counterclockwise and remove it from the fog light housing. 2. Remove the bulb from the connector socket and install the replacement bulb. CAUTION! Do not touch the new bulb with your fingers. Oil contamination - 2008 Chrysler Sebring | Owner Manual Sedan - Page 426
The taillights are a two piece design. The turn signal, brake and taillights are located in the rear corner body panel housing. The back up and taillights are located in the trunk lid housing. Changing the Tail/Stop Light or Rear Turn Signal Light 1. Open the trunk and gently pull back the trunk - 2008 Chrysler Sebring | Owner Manual Sedan - Page 427
connector onequarter turn counterclockwise and remove it from the taillight housing. 7 Location Plastic Wing Nuts 3. Grasp the taillight housing and pull it firmly outward while pushing gently on the studs from inside to disengage the housing from the vehicle. 1 - Tail/Stop Light 2 - Turn Signal - 2008 Chrysler Sebring | Owner Manual Sedan - Page 428
VEHICLE 5. Remove the bulb from the connector socket and install the replacement bulb. 6. Install the bulb and connector assembly into the taillight housing and rotate the connector one-quarter turn clockwise to lock it in place. 7. Reinstall the taillight housing. Changing the Backup Light 1. Open - 2008 Chrysler Sebring | Owner Manual Sedan - Page 429
and install the replacement bulb. 4. Install the bulb and connector assembly into the housing and rotate the connector one-quarter turn clockwise to lock it in place. License Plate Light 1. Remove two retaining screws holding the light lens in place. Location and Removal of Rear License Light Lens - 2008 Chrysler Sebring | Owner Manual Sedan - Page 430
VEHICLE Center High-Mounted Stop Light (CHMSL) 1. Open the trunk lid. 2. Rotate the bulb's electrical connector one-quarter turn counterclockwise and remove it from the CHMSL housing. 3. Remove the bulb from the connector socket and install the replacement bulb. 4. Install the bulb and connector - 2008 Chrysler Sebring | Owner Manual Sedan - Page 431
gallons 2.4L PZEV (Partial Zero Emissions Vehicle) 18.4 gallons Engine Oil with Filter 2.4 Liter Engine (SAE 5W-20, API Certified) 4.5 quarts 2.7 Liter Engine (SAE 10W-30, API Certified) 5.5 quarts Cooling System * 2.4 Liter Engine (Mopar Antifreeze/Coolant 5 Year/100,000 Mile For7.7 quarts mula) - 2008 Chrysler Sebring | Owner Manual Sedan - Page 432
Engine Oil (2.4L & 2.7L) Fluids, Lubricants, and Genuine Parts Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula 27 mm]) ZFR5LP-13G (Gap.050 in [1.27 mm]) 87 Octane Engine Oil (3.5L) Oil Filter (2.4L) Oil Filter (2.7L & 3.5L) Spark Plugs (2.4L - EXCEPT PZEV*) Spark Plugs (2.4L- with PZEV Spark - 2008 Chrysler Sebring | Owner Manual Sedan - Page 433
MAINTAINING YOUR VEHICLE 431 Component Fuel Selection (2.7L - EXCEPT CALIE-85 Ethanol FORNIA EMISSION STATES) Fuel Selection (3.5L) 87 to 89 Octane * PZEV = Partial Zero Emission Vehicle Fluids, Lubricants, and Genuine Parts 7 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 434
Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts Mopar ATF+4 Automatic Transmission Fluid. Mopar DOT 3 and SAE J1703 should be used. If DOT 3 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids. Mopar ATF+4 Automatic Transmission Fluid. - 2008 Chrysler Sebring | Owner Manual Sedan - Page 435
MAINTENANCE SCHEDULES CONTENTS Ⅵ Emissions Control System Maintenance ...434 Ⅵ Maintenance Schedule ...434 ▫ Required Maintenance Intervals ...437 M A I N T E N A N C E S C H E D U L E S 8 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 436
of the emission control system. These, and all other maintenance services included in this manual, should be done to replacement, or repair of the emissions control devices and systems on your vehicle may be performed by any automotive repair establishment or individual using any automotive part - 2008 Chrysler Sebring | Owner Manual Sedan - Page 437
drive manual or under "Odometer/Trip Odometer" under "Instrument Cluster Descriptions" in Section 3 of this manual battery and clean and tighten the terminals S as required. • Check the fluid levels of coolant reservoir, brake master cylinder, power steering, and automatic transaxle, and add fluid - 2008 Chrysler Sebring | Owner Manual Sedan - Page 438
- if equipped is sealed, therefore checking the fluid level can only be done by a certified dealership service center. • Check all lights and other electrical items for correct operation. At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines. CAUTION! Failure to - 2008 Chrysler Sebring | Owner Manual Sedan - Page 439
cleaner filter, and replace if necessary. Inspect the brake linings, and replace if necessary. Replace the air conditioning filter (if equipped). Inspect the CV joints. Perform the first inspection at 12,000 miles (20 000 km) or 12 months. Inspect the exhaust system. Perform the first inspection at - 2008 Chrysler Sebring | Owner Manual Sedan - Page 440
170 000 or Months 30 30 30 60 90 60 102 102 102 8 sion on 2.4L engines. Inspect the generator belt on 2.4L engines, and replace if necessary. Change the automatic transaxle fluid & filter if using your vehicle for any of the following: police, taxi, fleet, or frequent trailer towing. Inspect and - 2008 Chrysler Sebring | Owner Manual Sedan - Page 441
Replace the timing belt on 2.4L and 3.5L engines. Change the automatic transaxle fluid & filter. Replace the accessory drive belt vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your - 2008 Chrysler Sebring | Owner Manual Sedan - Page 442
- 2008 Chrysler Sebring | Owner Manual Sedan - Page 443
▫ In Mexico Contact ...444 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) ...445 ▫ Service Contract ...445 Ⅵ Warranty Information (U.S. Vehicles Only) ...446 Ⅵ Mopar Parts ...446 Ⅵ Reporting Safety Defects ...446 ▫ In The 50 United States And Washington, D.C...446 ▫ In Canada - 2008 Chrysler Sebring | Owner Manual Sedan - Page 444
442 IF YOU NEED CONSUMER ASSISTANCE Ⅵ Publication Order Forms ...447 Ⅵ Department Of Transportation Uniform Tire Quality Grades ...449 ▫ Treadwear ...449 ▫ Traction Grades ...449 ▫ Temperature Grades ...450 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 445
be covered by the warranty. Discuss additional charges with the service manager. Keep a maintenance log of your vehicle's service history. This can often provide a clue to the current problem. Prepare A List Make a written list of your vehicle's problems or the specific work you want done. If you've - 2008 Chrysler Sebring | Owner Manual Sedan - Page 446
timely manner. This is why you should always talk to your authorized dealer's service manager first. Most matters can be resolved with this process. • If for Vehicle delivery date and mileage DaimlerChrysler Motors Corporation Customer Center P.O. Box 21-8004 Auburn Hills, MI 48321-8004 Phone: (800 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 447
To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at with the manufacturer by dialing 1-800-380-CHRY. Service Contract You may have purchased a service contract for your vehicle to help protect you from - 2008 Chrysler Sebring | Owner Manual Sedan - Page 448
birth defects or other reproductive harm. MOPARா PARTS Mopar fluids, lubricants, parts, and accessories are available from your authorized dealer. They remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. WARRANTY - 2008 Chrysler Sebring | Owner Manual Sedan - Page 449
technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing, and repairing DaimlerChrysler Corporation vehicles. A complete working knowledge of the vehicle, system, and/or components is written in straightforward language with illustrations, diagrams, and charts. 9 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 450
with diagrams, charts and detailed illustrations, these practical manuals make it easy for students and technicians to find and fix problems on computercontrolled vehicle systems and features. They show exactly how to find and correct problems the first time, using step-by-step troubleshooting and - 2008 Chrysler Sebring | Owner Manual Sedan - Page 451
and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate. Traction Grades The tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics - 2008 Chrysler Sebring | Owner Manual Sedan - Page 452
car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law. WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not - 2008 Chrysler Sebring | Owner Manual Sedan - Page 453
INDEX 10 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 454
ABS (Anti-Lock Brake System) ...282 Accessory Delay, Power ...13 Adding Engine Coolant (Antifreeze) ...396 Adding Fuel ...332 Adding Washer Fluid ...140,393 Additives, Fuel ...326 Air Cleaner, Engine (Engine Air Cleaner Filter) ...385 Air Conditioner Maintenance ...388 Air Conditioning ...243 Air - 2008 Chrysler Sebring | Owner Manual Sedan - Page 455
Back-Up Lights ...424 Ball Joints ...391 Battery ...387 Gas Caution ...387 Jump Starting ...29 Keyless Transmitter Replacement (RKE) ...25 Location ...387 Bearings ...406 Belts, Drive ...384 Body Mechanism Lubrication ...392 B-Pillar Location ...299 Brake Assist System ...286 Brake, Parking ...277 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 456
454 INDEX Break-In Recommendations, New Vehicle ...78 Bulb Replacement ...417,418 Bulbs, Light ...417 Calibration, Compass ...188 Capacities, Antifreeze (Engine Coolant) ...20 Capacities, Fluid ...429 Caps, Filler Fuel ...332 Oil (Engine) ...374,375,376,383 Radiator (Coolant Pressure) ...397 Car - 2008 Chrysler Sebring | Owner Manual Sedan - Page 457
157 Contract, Service ...445 Converter, Catalytic ...385 Coolant Pressure Cap (Radiator Cap) ...397 Cooling System ...394 Adding Coolant (Antifreeze) ...396 Selection of Coolant (Antifreeze) ...395,429,430 Corrosion Protection ...406 Crankcase Ventilation Module ...20 Cruise Light ...176 Cup Holder - 2008 Chrysler Sebring | Owner Manual Sedan - Page 458
Disposal Antifreeze (Engine Coolant) ...398 Engine Oil ...384 Door Locks, Automatic ...31 Door Opener, Garage ...144 Drive Belts ...384 Driving On Emergency Trunk Release ...39,40 Emission Control System Maintenance ...378,434 Engine ...78,374,375,376 Air Cleaner ...385 Block Heater ...269 Break-In - 2008 Chrysler Sebring | Owner Manual Sedan - Page 459
324 Event Data Recorder ...65 Exhaust Gas Caution ...78,327,394 Exhaust System ...393 Extender, Seat Belt ...51 Fabric Care ...408,409 Filler Location Fuel ...172,332 Filters Air Cleaner ...385 Air Conditioning ...256,389 Automatic Transaxle ...405 Engine Oil ...384,430 Engine Oil Disposal ...384 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 460
Brake ...402,432 Cooling System ...395 Engine Oil ...380 Power Steering ...391,432 Fluids ...430 Fluids, Lubricants and Genuine Parts ...430 Fog Light Service ...422 Fog Lights ...134,179,422 Folding Rear Seat ...128,129 Freeing A Stuck Vehicle ...367 Front Wheel Bearings ...406 Fuel ...323 Adding - 2008 Chrysler Sebring | Owner Manual Sedan - Page 461
Fuses ...412 Garage Door Opener (HomeLink) ...144 Gas Cap (Fuel Filler Cap) ...332,334,377 Gasoline, Clean Air ...324 Gasoline (Fuel Axle Weight Rating ...336,339 Gross Vehicle Weight Rating ...336,338 GVWR ...336 Hands-Free Phone (UConnect™) ...89,225,227 Hard Drive (HDD) ...222,225 Hazard Driving - 2008 Chrysler Sebring | Owner Manual Sedan - Page 462
...412 Interior Appearance Care ...408 Interior Lights ...131 Intermittent Wipers (Delay Wipers) ...138 Introduction ...4 Jack Location ...356 Jack Operation ...356,358 Jacking Instructions ...358 Jump Starting ...364 Key, Programming ...Key, Replacement ...Key, Sentry (Immobilizer) Key-In Reminder - 2008 Chrysler Sebring | Owner Manual Sedan - Page 463
Signals ...179 Lap/Shoulder Belts ...42 LATCH (Lower Anchors and Tether for CHildren) . 73 Latches Hood ...130 Lead Free Gasoline ...323 Life of Tires ...309 Light Bulbs ...417 Lights ...80,131 Airbag ...53,65,79,173 Back-Up ...424 Brake Warning ...178 Bulb Replacement ...418 Center Mounted Stop - 2008 Chrysler Sebring | Owner Manual Sedan - Page 464
, Body ...392 Lumbar Support ...124 Maintenance Free Battery ...387 Maintenance, General ...380 Maintenance Procedures ...380 Maintenance Schedule ...434 Malfunction Indicator Light (Check Engine) . . 182,378 Manual, Service ...447 Map/Reading Lights ...131 Master Cylinder (Brakes) ...402 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 465
382 Materials Added to ...384 Recommendation ...382,429 Synthetic ...383 Viscosity ...383,429 Oil Filter, Change ...384 Oil Filter, Selection ...384 Oil Pressure Light ...173 Onboard Diagnostic System ...377,378 Opener, Garage Door (HomeLink) ...144 Operator Manual (Owner's Manual) ...4 Overdrive - 2008 Chrysler Sebring | Owner Manual Sedan - Page 466
Parking Brake ...277 Parking On Hill ...278 Passing Light ...134 Personal Settings ...190 Pets ...77 Phone, Cellular ...89,225,227 Phone, Hands-Free (UConnect™) ...89,225,227 Placard, Tire and Loading Information ...299 Port Universal Serial Bus (USB) ...222,225 USB ...222,225 Power Accessory Delay - 2008 Chrysler Sebring | Owner Manual Sedan - Page 467
Belt ...49 Remote Control Door Locks ...21 Security Alarm ...18 Remote Keyless Entry (RKE) ...21 Remote Keyless Entry (Sedan) ...21 Remote Sound System (Radio) Controls ...238 Remote Starting System ...27 Remote Trunk Release ...38 Replacement Bulbs ...417 Replacement Keys ...16 Replacement Parts - 2008 Chrysler Sebring | Owner Manual Sedan - Page 468
51 Front Seat ...42,43 Operating Instructions ...43 Pretensioners ...48 Rear Seat ...42 Reminder ...173 Untwisting Procedure ...47 Seat Belts (Sedan) ...40 Seats ...121 Adjustment ...121 Cleaning ...129,409 Head Restraints ...125 Heated ...126 Lumbar Support ...124 Power ...124 Rear Folding ...128 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 469
INDEX 467 Settings, Personal ...190 Shoulder Belts ...42 Side Window Demisters (Defrosters) ...255 Signals, Turn ...424 Slippery Surfaces, Driving On ...291 Snow Chains (Tire Chains) ...312 Snow Tires ...312 Sound Systems (Radio) ...222,225 Spare Tire ...307,356 Spark Plugs ...385 Specifications - 2008 Chrysler Sebring | Owner Manual Sedan - Page 470
Tires ...80,303,449 Aging (Life of Tires) ...309 Air Pressure ...303 Alignment ...312 Chains ...312 Changing ...356 Compact Spare ...307 Flat 299,300 Pressure Monitor System (TPMS) ...314 Quality Grading ...449 Radial ...306 Replacement ...310 Rotation ...313 Safety ...294,303 Sizes ...296 Snow Tires - 2008 Chrysler Sebring | Owner Manual Sedan - Page 471
Trailer Towing Guide ...341 Trailer Weight ...341 Transaxle ...270 Additives ...405 Automatic ...13,264,270,403 Autostick ...275 Filter ...405 Maintenance ...403 Operation ...270 Overdrive ...274 Selection of Lubricant ...432 Transmission Range Indicator ...174 Transmitter Battery Service (Remote - 2008 Chrysler Sebring | Owner Manual Sedan - Page 472
System (VR) ...116 Warning Lights (Instrument Cluster Description) ...172 Warnings and Cautions ...6 Warranty Information ...446 Washer, Adding Fluid ...140,393 Washers, Windshield ...136,140,393 Washing Vehicle ...407 Water Driving Through ...292 Wheel Alignment and Balance ...312 Wheel and Wheel - 2008 Chrysler Sebring | Owner Manual Sedan - Page 473
Blade Replacement ...392,393 Wipers, Intermittent ...138 YES Essentials Fabric Cleaning Procedure ...409 ABS (Anti-Lock Brake System) ...282 Accessory Delay, Power ...13 Adding Engine Coolant (Antifreeze) ...396 Adding Fuel ...332 Adding Washer Fluid ...140,393 Additives, Fuel ...326 Air Cleaner - 2008 Chrysler Sebring | Owner Manual Sedan - Page 474
472 INDEX Alignment and Balance ...312 Alterations/Modifications, Vehicle ...7 Antenna, Satellite Radio ...235 Antifreeze (Engine Coolant) ...395,396,429 Disposal ...398 Anti-Lock Brake System (ABS) ...282 Anti-Lock Warning Light ...282 Anti-Theft Security Alarm (Theft Alarm) ...18 Appearance Care - 2008 Chrysler Sebring | Owner Manual Sedan - Page 475
...406 Belts, Drive ...384 Body Mechanism Lubrication ...392 B-Pillar Location ...299 Brake Assist System ...286 Brake, Parking ...277 Brake System ...281,400 Anti-Lock (ABS) ...282 Fluid Check ...402,432 Hoses ...401 Master Cylinder ...402 Parking ...277 Warning Light ...178 Brakes ...281,400 Brake - 2008 Chrysler Sebring | Owner Manual Sedan - Page 476
Interface (UCI) ...229 Console ...129,157 Console, Floor ...129,157 Contract, Service ...445 Converter, Catalytic ...385 Coolant Pressure Cap (Radiator Cap) ...397 Cooling System ...394 Adding Coolant (Antifreeze) ...396 Coolant Capacity ...429 Coolant Level ...395,398 Disposal of Used Coolant - 2008 Chrysler Sebring | Owner Manual Sedan - Page 477
Transaxle ...403,404 Oil (Engine) ...380 Disabled Vehicle Towing ...368 Disposal Antifreeze (Engine Coolant) ...398 Engine Oil ...384 Door Locks, Automatic ...31 Door Opener, Garage ...144 Drive Belts ...384 Driving On Slippery Surfaces ...291 Through Flowing, Rising, or Shallow Standing Water - 2008 Chrysler Sebring | Owner Manual Sedan - Page 478
...364 Towing ...368 Emergency Trunk Release ...39,40 Emission Control System Maintenance ...378,434 Engine ...78,374,375,376 Air Cleaner ...385 Block Heater ...269 Break-In Recommendations ...78 Checking Oil Level ...380 Coolant (Antifreeze) ...395,430 Cooling ...394 Exhaust Gas Caution ...327 Fuel - 2008 Chrysler Sebring | Owner Manual Sedan - Page 479
Brake ...402,432 Cooling System ...395 Engine Oil ...380 Power Steering ...391,432 Fluids ...430 Fluids, Lubricants and Genuine Parts ...430 Fog Light Service ...422 Fog Lights ...134,179,422 Folding Rear Seat ...128,129 Freeing A Stuck Vehicle ...367 Front Wheel Bearings ...406 Fuel ...323 Adding - 2008 Chrysler Sebring | Owner Manual Sedan - Page 480
478 INDEX Additives ...326 Clean Air ...324 Ethanol ...324 Filler Cap (Gas Cap) ...172,332 Filler Door (Gas Cap) ...172 Gasoline ...323 Gauge ...172 Hoses ...400 Light ...173 Materials Added ...326 Methanol ...324 Octane Rating ...323,430 Requirements ...323,429 Tank Capacity ...429 Fuel, Flexible - 2008 Chrysler Sebring | Owner Manual Sedan - Page 481
INDEX 479 Hands-Free Phone (UConnect™) ...89,225,227 Hard Drive (HDD) ...222,225 Hazard Driving Through Flowing, Rising, or Shallow Standing Water ...292 Hazard Warning Flasher ...353 Head Restraints ...125 Headlights ...418 Bulb Replacement ...418 Cleaning ...410 High Beam ...136,182 High Beam/ - 2008 Chrysler Sebring | Owner Manual Sedan - Page 482
Signals ...179 Lap/Shoulder Belts ...42 LATCH (Lower Anchors and Tether for CHildren) . 73 Latches Hood ...130 Lead Free Gasoline ...323 Life of Tires ...309 Light Bulbs ...417 Lights ...80,131 Airbag ...53,65,79,173 Back-Up ...424 Brake Warning ...178 Bulb Replacement ...418 Center Mounted Stop - 2008 Chrysler Sebring | Owner Manual Sedan - Page 483
License ...427 Lights On Reminder Rear Tail ...424 Seat Belt Reminder ...173 Security Auto Unlock ...32 Child Protection ...33 Power Door ...31 Low Tire Pressure System ...314 Lower Anchors and Tether for CHildren (LATCH) ...73 Lubrication, Body ...392 Lumbar Support ...124 Maintenance Free Battery - 2008 Chrysler Sebring | Owner Manual Sedan - Page 484
,378 Manual, Service ...447 Map/Reading Lights ...131 Master Cylinder (Brakes) ...402 Methanol ...324 Mini-Trip Computer ...186 Mirrors ...85 Automatic Dimming ...86 Electric Powered ...87 Outside ...88 Rearview ...85 Vanity ...89 Modifications/Alterations, Vehicle ...7 Monitor, Tire Pressure System - 2008 Chrysler Sebring | Owner Manual Sedan - Page 485
382 Materials Added to ...384 Recommendation ...382,429 Synthetic ...383 Viscosity ...383,429 Oil Filter, Change ...384 Oil Filter, Selection ...384 Oil Pressure Light ...173 Onboard Diagnostic System ...377,378 Opener, Garage Door (HomeLink) ...144 Operator Manual (Owner's Manual) ...4 Overdrive - 2008 Chrysler Sebring | Owner Manual Sedan - Page 486
,225,227,234 Radio (Sound Systems) ...222,225 Rear Cup Holder ...161 Rear Seat, Folding ...128,129 Rear Wheel Bearings ...406 Rear Window Defroster Belt ...49 Remote Control Door Locks ...21 Security Alarm ...18 Remote Keyless Entry (RKE) ...21 Remote Keyless Entry (Sedan) ...21 Remote Sound System - 2008 Chrysler Sebring | Owner Manual Sedan - Page 487
...48 Adjustable Upper Shoulder Anchorage ...48 And Pregnant Women ...51 Child Restraint ...67,76 Extender ...51 Front Seat ...42,43 Operating Instructions ...43 Pretensioners ...48 Rear Seat ...42 Reminder ...173 Untwisting Procedure ...47 Seat Belts (Sedan) ...40 Seats ...121 Adjustment ...121 10 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 488
Service Contract ...445 Service Manuals ...447 Setting the Clock ...193,196,208,224,227 Settings, Personal ...190 Shoulder Belts ...42 Side Window Demisters (Defrosters) ...255 Signals, Turn ...424 Slippery Surfaces, Driving On ...291 Snow Chains (Tire Chains) ...312 Snow Tires ...312 Sound Systems - 2008 Chrysler Sebring | Owner Manual Sedan - Page 489
System - Airbag ...52 Synthetic Engine Oil ...383 System, Navigation ...225 Tachometer ...174 Taillights ...424 Telescoping Steering Column ...140 Temperature Control, Automatic 80,303,449 Aging (Life of Tires) ...309 Air Pressure ...303 Alignment ...312 Chains ...312 Changing ...356 Compact Spare - 2008 Chrysler Sebring | Owner Manual Sedan - Page 490
Trailer Towing ...338 Cooling System Tips ...349 Hitches ...340 Minimum Requirements ...343 Trailer and Tongue Weight ...342 Wiring ...346 Trailer Towing Guide ...341 Trailer Weight ...341 Transaxle ...270 Additives ...405 Automatic ...13,264,270,403 Autostick ...275 Filter ...405 Maintenance ...403 - 2008 Chrysler Sebring | Owner Manual Sedan - Page 491
Lubricant ...432 Transmission Range Indicator ...174 Transmitter Battery Service (Remote Keyless Entry) ...25 Transmitter, Garage Door Opener (HomeLink Remote Control ...38 Turn Signals ...135,179,424 UCI Connector ...229 UConnect™ (Hands-Free Phone) ...89,225 Understanding Your Instrument Panel ... - 2008 Chrysler Sebring | Owner Manual Sedan - Page 492
System (VR) ...116 Warning Lights (Instrument Cluster Description) ...172 Warnings and Cautions ...6 Warranty Information ...446 Washer, Adding Fluid ...140,393 Washers, Windshield ...136,140,393 Washing Vehicle ...407 Water Driving Through ...292 Wheel Alignment and Balance ...312 Wheel and Wheel - 2008 Chrysler Sebring | Owner Manual Sedan - Page 493
during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible. The negative power connection should be made to body sheet metal adjacent to the negative battery connection. This connection should not be fused. Antennas for - 2008 Chrysler Sebring | Owner Manual Sedan - Page 494
81-026-0804 Second Edition Printed in U.S.A.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
-
313
-
314
-
315
-
316
-
317
-
318
-
319
-
320
-
321
-
322
-
323
-
324
-
325
-
326
-
327
-
328
-
329
-
330
-
331
-
332
-
333
-
334
-
335
-
336
-
337
-
338
-
339
-
340
-
341
-
342
-
343
-
344
-
345
-
346
-
347
-
348
-
349
-
350
-
351
-
352
-
353
-
354
-
355
-
356
-
357
-
358
-
359
-
360
-
361
-
362
-
363
-
364
-
365
-
366
-
367
-
368
-
369
-
370
-
371
-
372
-
373
-
374
-
375
-
376
-
377
-
378
-
379
-
380
-
381
-
382
-
383
-
384
-
385
-
386
-
387
-
388
-
389
-
390
-
391
-
392
-
393
-
394
-
395
-
396
-
397
-
398
-
399
-
400
-
401
-
402
-
403
-
404
-
405
-
406
-
407
-
408
-
409
-
410
-
411
-
412
-
413
-
414
-
415
-
416
-
417
-
418
-
419
-
420
-
421
-
422
-
423
-
424
-
425
-
426
-
427
-
428
-
429
-
430
-
431
-
432
-
433
-
434
-
435
-
436
-
437
-
438
-
439
-
440
-
441
-
442
-
443
-
444
-
445
-
446
-
447
-
448
-
449
-
450
-
451
-
452
-
453
-
454
-
455
-
456
-
457
-
458
-
459
-
460
-
461
-
462
-
463
-
464
-
465
-
466
-
467
-
468
-
469
-
470
-
471
-
472
-
473
-
474
-
475
-
476
-
477
-
478
-
479
-
480
-
481
-
482
-
483
-
484
-
485
-
486
-
487
-
488
-
489
-
490
-
491
-
492
-
493
-
494
 |
 |
Sebring
O W N E R ’ S M A N U A L
2 0 0 8
2008 Sebring