Home » Lexus Manuals » 2004 Lexus RX 330 » Manual Viewer

2004 Lexus RX 330 Owners Manual - Page 146

2004 Lexus RX 330 Manual

Get 2004 Lexus RX 330 PDF manuals and user guides

View all 2004 Lexus RX 330 manuals

Page 146 highlights

INTERIOR EQUIPMENT The battery side of the hand-held transmitter must be pointed away from the HomeLinkR during the programming process. For Canadian users, follow the procedure in "Programming an entrance gate/Programming all devices in the Canadian market". 1. Decide which of 3 HomeLinkR buttons you want to program. 2. Place your hand-held garage transmitter 25 to 75 mm (1 to 3 in.) away from the surface of the HomeLinkR. Keep the indicator light on the HomeLink R in view while programming. 3. Simultaneously press and hold the hand-held garage transmitter button along with the selected HomeLinkR button. 4. When the indicator light on the HomeLinkR changes from a slow to a rapid flash after 20 seconds, you can release both buttons. 5. Test the operation of the HomeLinkR by pressing the newly programmed button. If programming a garage door opener, check to see if the garage door opens and closes. If the garage door does not operate, identify if your garage transmitter is of the "Rolling Code" type. Press and hold the programmed HomeLinkR button. The garage door has the rolling code feature if the indicator light (on the HomeLinkR) flashes rapidly and then remains lit after 2 seconds. If your garage transmitter is the "Rolling Code" type, proceed to the heading "Programming a rolling code system". 6. Repeat steps 2 through 5 for each remaining HomeLinkR button to program another device. Programming a rolling code system If your device is "Rolling Code" equipped, it is necessary to follow steps 1 through 4 under the heading "Programming the HomeLinkR" before proceeding with the steps listed below. 1. Locate the "training" button on the ceiling mounted garage door opener motor. The exact location and color of the button may vary by brand of garage door opener. Refer to the owner's guide supplied by the garage door opener manufacturer for the location of this "training" button. 2. Press the "training" button on the ceiling mounted garage door opener motor. Following this step, you have 30 seconds in which to initiate step 3 below. 123

Section	Page
Seat Belt Information	1
Gas Station Information	2
Repair Manual Information	3
Foreword	5
Important Information About Your Lexus	6
How To Use This Manual	10
Pictorial Index	13
Quick Reference	24
Keys and Doors	34
Switches	74
Gauges, Meters and Service Reminder Indicators	103
Interior Equipment	130
Exterior Equipment	163
Occupant Restraint Systems	180
Steering Wheel and Mirrors	278
Air Conditioning	293
Audio	317
Starting and Driving	449
Driving Tips	540
In Case of An Emergency	572
Maintenance	629
Introduction	637
Engine	652
Chassis	670
Electrical Components	702
Body	734
Reporting Safety Defects For U.S. Owners	748

Match case Limit results 1 per page

INTERIOR EQUIPMENT

123

The battery side of the hand-held transmitter must be pointed

away from the HomeLink

during the programming process.

For Canadian users, follow the procedure in “Programming an

entrance gate/Programming all devices in the Canadian

market”.

Decide which of 3 HomeLink

buttons you want to program.

Place your hand-held garage transmitter 25 to 75 mm (1 to

3 in.) away from the surface of the HomeLink

Keep the indicator light on the HomeLink

in view while

programming.

3. Simultaneously press and hold the hand-held garage

transmitter button along with the selected HomeLink

button.

When the indicator light on the HomeLink

changes from a

slow to a rapid flash after 20 seconds, you can release both

buttons.

Test the operation of the HomeLink

by pressing the newly

programmed button.

If programming a garage door opener,

check to see if the garage door opens and closes.

If the garage door does not operate, identify if your garage

transmitter is of the “Rolling Code” type.

Press and hold the

programmed HomeLink

button.

The garage door has the

rolling code feature if the indicator light (on the HomeLink

)

flashes rapidly and then remains lit after 2 seconds.

If your

garage transmitter is the “Rolling Code” type, proceed to the

heading “Programming a rolling code system”.

6. Repeat steps 2 through 5 for each remaining HomeLink

button to program another device.

Programming a rolling code system

If your device is “Rolling Code” equipped, it is necessary

to follow steps 1 through 4 under the heading

“Programming the HomeLink

” before proceeding with

the steps listed below.

Locate the “training” button on the ceiling mounted garage

door opener motor.

The exact location and color of the button

may vary by brand of garage door opener.

Refer to the owner’s

guide supplied by the garage door opener manufacturer for the

location of this “training” button.

2. Press the “training” button on the ceiling mounted garage

door opener motor.

Following this step, you have 30 seconds in which to initiate

step 3 below.