1996 Mercury Villager Owner's Manual
1996 Mercury Villager Manual
1996 Mercury Villager manual content summary:
- 1996 Mercury Villager | Owner's Manual - Page 1
Controls and features Seating and safety restraints Starting and driving Starting Driving Roadside emergencies Servicing any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Copyright 1999 Ford - 1996 Mercury Villager | Owner's Manual - Page 2
first 1 600 km (1 000 miles) of driving, vary speeds frequently. This is necessary to give the moving parts a chance to break in. INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring - 1996 Mercury Villager | Owner's Manual - Page 3
Instrumentation 3 - 1996 Mercury Villager | Owner's Manual - Page 4
Instrumentation Instrument cluster (pg. 6) Panel dimmer (pg. 19) Headlamp control (pg. 19) 3 2 AUTO 1 AUTO 2 4 40 5 6 7 50 60 80 100 70 80 and wiper/washer control (pg. 86) Speed control (pg. 85) Audio controls * (pg. 85) Driver side air bag (pg. 131) Anti-theft indicator light* (pg. 104 - 1996 Mercury Villager | Owner's Manual - Page 5
SECUR ITY Electronic sound system (pg. 40) VOL - PUSH ON DC 12V AM FM BASS TREB BAL FADE CLK TAPE AMS CD SEEK TUNE SCAN EJ SIDE 1 - 2 REW FF DISCS CD CD COMP SHUFFLE 1 1 2 3 4 5 6 Climate control system (pg. 21) 2 3 4 MAX A/C OFF OFF REAR 1 2 3 4 A/C CD Changer* (pg. 76) 5 - 1996 Mercury Villager | Owner's Manual - Page 6
MPH km/h km FUEL DOOR 1/2 N O R M A L E C UNLEADED FUEL ONLY ABS SERVICE ENGINE SOON AIR BAG ! P BRAKE P R N D 2 1 O/D OFF Charging system Illuminates when the ignition is turned to the ON position and the engine is off. The light also illuminates when the battery is not charging properly - 1996 Mercury Villager | Owner's Manual - Page 7
to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter. Brake system warning Momentarily illuminates when and switch off the engine immediately. Check the oil level and add oil if needed. Refer to Engine oil in the Maintenance and Care chapter. Door ajar - 1996 Mercury Villager | Owner's Manual - Page 8
is turned to the ON ABS position. If the light remains on, continues to flash or fails to illuminate, have the system serviced immediately. With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the brake warning light also remains illuminated with - 1996 Mercury Villager | Owner's Manual - Page 9
II system also assists the service technician in properly servicing your vehicle. The Service Engine Soon indicator light illuminates when the ignition is first turned to the ON position to check the bulb. If it comes on after the engine is started, one of the engine's emission control systems may - 1996 Mercury Villager | Owner's Manual - Page 10
Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. O/D off Illuminates when the Transmission O/D Control Switch (TCS), refer to OFF Overdrive control in - 1996 Mercury Villager | Owner's Manual - Page 11
OUTSIDE TEMP INST ECONOMY AVG. ECONOMY TO EMPTY MPH km/h km FUEL DOOR 1/2 N O R M A L E C UNLEADED FUEL ONLY ABS SERVICE ENGINE SOON AIR BAG ! P BRAKE P R N D 2 1 O/D OFF Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at - 1996 Mercury Villager | Owner's Manual - Page 12
Instrumentation • Standard analog instrument cluster 3 2 1 0 4 5 6 7 RPMx1000 8 • Optional electronic instrument cluster CRUISE 3 4 5 6 7 8 2 1 0 X 1000 TRIP 1 TRIP 2 RPM MPH km/h km Speedometer Indicates the current vehicle speed. • Standard analog instrument cluster 40 30 20 10 0 40 - 1996 Mercury Villager | Owner's Manual - Page 13
(miles) of individual journeys. • Standard analog instrument cluster To reset, depress the control. 0 0 0 0 • Optional electronic instrument cluster Refer to Electronic Message Center for information on how to switch the display from Trip 1 and Trip 2 features on the electronic instrument cluster - 1996 Mercury Villager | Owner's Manual - Page 14
the normal area (the area between the "H" and "C"). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the ignition and let it cool. Refer to Engine coolant in the Maintenance and care chapter. This gauge indicates the temperature of the - 1996 Mercury Villager | Owner's Manual - Page 15
ELECTRONIC MESSAGE CENTER (IF EQUIPPED) The electronic message center only works when the ignition is in the ON position. The message center allows you center to display by using the message center controls located to the left of the instrument panel. Selectable features SELECT Press this control to - 1996 Mercury Villager | Owner's Manual - Page 16
to reset the trip 1 and 2 odometer (which ever is displayed). OD/TRIP Press this control to switch between the permanent odometer mileage and the trip 1 and 2 odometer mileage. Message center functions OUTSIDE TEMP Press SELECT until the menu displays OUTSIDE TEMP. This will display the temperature - 1996 Mercury Villager | Owner's Manual - Page 17
to the nearest 0.1 liter (gallon) Checking your highway fuel economy using the electronic message center display Use the following procedure will allow you to accurately monitor your actual highway fuel economy. This procedure requires the vehicle speed control system to be set to highway speeds - 1996 Mercury Villager | Owner's Manual - Page 18
. This current SELECT OD / TRIP average measure will change as the speed control system changes the engine speed to maintain a constant vehicle speed. This is most noticeable in hilly environments fuel tank. When the engine is restarted, the message center will display the last setting selected. 18 - 1996 Mercury Villager | Owner's Manual - Page 19
• the headlamp control is in the OFF or Parking lamps position. Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Light (DRL) System does not activate your tail lamps and generally may not provide adequate lighting during these conditions. Failure to - 1996 Mercury Villager | Owner's Manual - Page 20
(IF EQUIPPED) The autolamp system provides light OFF AUTO sensitive automatic on-off control of 1 the exterior lights normally AUTO controlled by the headlamp control. 2 The autolamp system also keeps the lights on for a preselected period of time after the ignition switch is turned to OFF. • To - 1996 Mercury Villager | Owner's Manual - Page 21
and features CLIMATE CONTROL SYSTEM Manual heating and air conditioning system 1 2 3 4 MAX A/C OFF CLIMATE CONTROL SYSTEM A/C Fan speed control Controls the volume of air circulated in the vehicle. 1 2 3 4 Temperature control Controls the temperature of the airflow inside the vehicle - 1996 Mercury Villager | Owner's Manual - Page 22
during operation, it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle. Under normal conditions, your vehicle's climate control system should be left in any position other than MAX A/C or OFF when the - 1996 Mercury Villager | Owner's Manual - Page 23
air conditioner will automatically dehumidify the air to reduce fogging. However, the indicator will not light unless the A/C control is selected. Cooling your vehicle with outside air Cooling your vehicle with air conditioned outside air is quieter but less economical than using air conditioned - 1996 Mercury Villager | Owner's Manual - Page 24
located under the front seats. Airflow and temperature to the rear seating are regulated by the main climate control system. OFF REAR A/C 1 2 3 4 A/C The rear passenger compartment air conditioning system (if equipped) should be set to OFF, if rear heating is desired. Operating tips • In humid - 1996 Mercury Villager | Owner's Manual - Page 25
and block airflow and possibly damage your climate control system. • If the air conditioner works well in MAX A/C, but not in any other mode when the A/C control is selected, this may indicate that the odor and particulate air filter (if equipped) needs to be replaced. Do not place objects on top of - 1996 Mercury Villager | Owner's Manual - Page 26
and features The rear A/C fan speed control allows the rear passengers to control the volume of air that is distributed from the rear registers. 0 1 4 3 2 REAR A/C The rear seat A/C system is controlled from the main climate control system on the instrument panel. 1 2 3 4 MAX A/C OFF OFF - 1996 Mercury Villager | Owner's Manual - Page 27
any position (other than OFF), and depress the A/C control. 2. Set the fan speed on the Rear A/C fan control to a number between 1-4. REAR A/C 1 4 3 2 Front seat air flow regulation of the rear fan Set the main climate control rear fan control to a number between 1-4. This numerical setting will - 1996 Mercury Villager | Owner's Manual - Page 28
on the main climate control system to Rear A/C and turn the Rear A/C Fan Control to 0. For maximum cooling for the front seat passengers, set the rear fan switch to the OFF (0) position. Please note that the rear passenger air conditioning system is designed for air conditioning purposes only, and - 1996 Mercury Villager | Owner's Manual - Page 29
MAX HI TEMP AUTOMATIC OFF REAR 1 A/C 2 3 4 LO The EATC system will maintain a selected temperature and automatically control airflow. You can override automatic operation with any of the override controls or the fan speed control. Turning the EATC on OFF A/C MAX HI TEMP AUTOMATIC OFF - 1996 Mercury Villager | Owner's Manual - Page 30
achieve the selected temperature. The system will automatically determine fan speed, airflow location and if outside air or recirculated air is required. Fan speed remains automatic unless the fan speed control is turned. When in AUTOMATIC and weather conditions require heat, air will be sent to the - 1996 Mercury Villager | Owner's Manual - Page 31
is selected by pressing the temperature control. Temperature conversion OFF A/C MAX HI TEMP AUTOMATIC OFF REAR 1 A/C 2 3 4 LO Press the A/C (A/C) and (DEF) simultaneously for one second while rotating the fan speed dial upward until it stops moving, to switch between Fahrenheit and Celsius - 1996 Mercury Villager | Owner's Manual - Page 32
˚F AUTO To return to automatic fan operation, press AUTOMATIC. Manual override controls OFF A/C MAX HI TEMP AUTOMATIC OFF REAR 1 A/C 2 3 4 LO The override controls allow you to: • manually control where the airflow is directed • manually control the air conditioning operation • manually - 1996 Mercury Villager | Owner's Manual - Page 33
operation, it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle. Under normal conditions, your vehicle's climate control system should be left in any position other than MAX or OFF when the vehicle - 1996 Mercury Villager | Owner's Manual - Page 34
and will cool the inside of the vehicle faster. After pressing the MAX control, both the MAX and A/C A/C indicators will light and the airflow will be from the instrument panel registers. In this mode, the air conditioning will automatically engage if the outside temperature is about 4°C (40°F) or - 1996 Mercury Villager | Owner's Manual - Page 35
located under the front seats. Airflow and temperature to the rear seating are regulated by the main climate control system. OFF REAR A/C 1 2 3 4 A/C The rear passenger compartment air conditioning system (if equipped) should be set to OFF, if rear heating is desired. Operating tips • In humid - 1996 Mercury Villager | Owner's Manual - Page 36
and possibly damage your climate control system. • If the air conditioner works well in MAX A/C, but not in any other mode when the A/C control is selected, this may indicate that the passenger compartment odor and particulate air filter (if equipped) needs to be replaced. Do not place objects - 1996 Mercury Villager | Owner's Manual - Page 37
A/C fan speed control allows rear passengers to control the volume of air that is distributed from the rear registers. The rear A/C system is controlled from the main climate control system on the instrument panel. The rear seat A/C system is controlled from the main climate control system on the - 1996 Mercury Villager | Owner's Manual - Page 38
the main climate control rear fan control to a number between 1-4. This numerical settingwill take control of the airflow from the rear A/C fan control. Turning the Rear A/C off: OFF REAR A/C 1 2 3 4 A/C To turn the Rear A/C off, turn the Rear Fan Control on the main climate control system to OFF - 1996 Mercury Villager | Owner's Manual - Page 39
on the main climate control system to Rear A/C and turn the Rear A/C Fan Control to 0. For maximum cooling for the front seat passengers, set the rear fan switch to the OFF (0) position. Please note that the rear passenger air conditioning system is designed for air conditioning purposes only, and - 1996 Mercury Villager | Owner's Manual - Page 40
off automatically after 15 minutes or when the ignition is turned to the OFF position. To manually turn off the defroster before 15 minutes have passed, push the control again. USING YOUR AUDIO SYSTEM AM/FM Stereo/Cassette (CD changer compatible) VOL - PUSH ON AM FM BASS TREB BAL FADE CLK TAPE AMS - 1996 Mercury Villager | Owner's Manual - Page 41
is turned off, the volume will come back on at a "nominal" listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio, tape and CD changer modes (if equipped). AM FM CD AM/FM select in radio mode This control allows you to select AM or FM - 1996 Mercury Villager | Owner's Manual - Page 42
to continue reversing through the disc. to select the next disc in the CD changer. Hold the control • Press to fast-forward through the remaining discs. Seek function The seek function control works in radio or CD changer mode. Seek function in radio mode • Press to find the next listenable station - 1996 Mercury Villager | Owner's Manual - Page 43
, the first track of the current disc will automatically replay. Scan function The scan function works in radio or CD changer mode (if equipped). SCAN Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN - 1996 Mercury Villager | Owner's Manual - Page 44
and features Bass adjust The bass adjust control allows you to increase or decrease the audio system's bass output. BASS Treble adjust The treble adjust control allows you to increase or decrease the audio system's treble output. TREB Speaker balance adjust Speaker sound distribution can - 1996 Mercury Villager | Owner's Manual - Page 45
have a blank section of at least 4 seconds duration between programs. CD changer select (if equipped) • To enter CD changer mode while in radio or tape mode, press the CD control. AM FM CD Rewind The rewind control works in tape and CD changer (if equipped) modes. To rewind in tape mode, press the - 1996 Mercury Villager | Owner's Manual - Page 46
to stop rewinding the tape. SIDE REW 1 1-2 FF CD To rewind in CD changer mode, press the CD control (preset 1). Press the control again to deactivate rewind mode. Fast forward The fast forward control works in tape and CD changer modes. To fast forward in tape mode, press SIDE 1 - 2 the 1-2/FF - 1996 Mercury Villager | Owner's Manual - Page 47
only in tape mode. Dolby reduces 4 the amount of hiss and static during tape playback. Press the control to activate (and deactivate) Dolby noise reduction. The noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation. Setting the clock Press CLK to toggle - 1996 Mercury Villager | Owner's Manual - Page 48
decrease minutes and to increase minutes. SEEK TUNE SEEK TUNE The CLK control will allow you to switch between media display mode (radio station, stereo information, etc.) and for ten seconds before reverting back to the clock. In media mode, the media information will always be displayed. 48 - 1996 Mercury Villager | Owner's Manual - Page 49
(RSC) allow the rear seat passengers to operate the radio, tape, or CD changer (if equipped). VOLUME MEDIA MEM SEEK CD CD COMP SHUFFLE 1 2 3 4 5 6 To turn on the rear seat controls, press the memory preset controls 3 will appear in the radio display. and 5 at the same time. The Pressing - 1996 Mercury Villager | Owner's Manual - Page 50
successively to allow rear sear passengers to scroll through the 6 memory presets in AM, FM1, or FM2. Push the MEM control in CD changer mode (if equipped) to advance to the next disc. VOLUME MEDIA MEM SEEK Seek function • Press to find the next listenable station down the VOLUME - 1996 Mercury Villager | Owner's Manual - Page 51
Controls and features Premium AM/FM Cassette (CD changer compatible) BASS SEL VOL PUSH ON CD TAPE EJ TREB BAL FADE RDS / CLK MUTE SEEK TUNE SCAN AUTO AM FM REW FF SIDE 1.2 COMP SHUFF 1 2 3 4 5 6 Your audio system is equipped with selective lighting, a unique lighting strategy. - 1996 Mercury Villager | Owner's Manual - Page 52
set above a certain level and the ignition is turned off, the volume will come back on at a "nominal" listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio, tape and CD changer modes (if equipped). AM FM AM/FM select in radio mode This - 1996 Mercury Villager | Owner's Manual - Page 53
continue reversing through the disc. • Press to select the next disc in the CD changer. Hold the control to fast-forward through the remaining discs. Seek function The seek function control works in radio, tape or CD changer mode (if equipped). Seek function in radio mode • Press to find the next - 1996 Mercury Villager | Owner's Manual - Page 54
opposite side of the tape.) To stop on a particular selection, press the control again. Scan function in CD changer mode (if equipped) Press the SCAN control to hear a short sampling of all selections on the CD (The CD scans in a forward direction, wrapping back to the first track at the end of the - 1996 Mercury Villager | Owner's Manual - Page 55
last strong station available. To deactivate autoset and return to your audio system's manually set memory stations, press the AUTO control again. Bass adjust The bass adjust control allows you to increase or decrease the audio system's bass output. BASS SEL TREB Treble adjust The treble adjust - 1996 Mercury Villager | Owner's Manual - Page 56
function and begin play. • To begin CD play (if CD[s] are loaded), press the CD control. CD TAPE The first track of the disc will begin playing. After that, CD play will begin where it stopped last. Rewind The rewind control works in tape REW and CD changer modes (if equipped). 1 • In tape mode - 1996 Mercury Villager | Owner's Manual - Page 57
the control to activate (and deactivate) Dolby noise reduction. The noise reduction system is CD passages together for a more consistent listening level. Press the COMP control to activate and deactivate compression adjust. Shuffle feature (if equipped) The shuffle feature operates in CD changer - 1996 Mercury Villager | Owner's Manual - Page 58
to start this feature. Random order play will continue until the SHUFFLE control is pressed again. Radio Data System (RDS) feature When selected, the RDS (Radio Data System) function performs the RDS / CLK following: • Displays the radio station call letters • Displays the type of music format - 1996 Mercury Villager | Owner's Manual - Page 59
• Classic • Country • Info • Jazz • Oldies • R&B • Religious • Rock • Soft • Top 40 SEL Show • With RDS activated, press the RDS control until SHOW is displayed. • Use the SEL control to select the program TYPE, station NAME or NONE (no text displayed). RDS / CLK SEL RDS clock feature Refer to - 1996 Mercury Villager | Owner's Manual - Page 60
(RSC) allow the rear seat passengers to operate the radio, tape, or CD changer (if equipped). VOLUME MEDIA MEM SEEK REW FF SIDE 1.2 COMP SHUFF 1 2 3 4 5 6 To turn on the rear seat controls, press the memory preset controls 3 will appear in the radio display. and 5 at the same time - 1996 Mercury Villager | Owner's Manual - Page 61
to operate the headphones. The speakers will cut out once the / speaker on/off control is pressed. Press the deactivate headphones. Media select Push the MEDIA control to toggle between AM, FM1, FM2, tape, or CD changer (if equipped). MEDIA MEM SEEK control again to VOLUME MEDIA MEM SEEK 61 - 1996 Mercury Villager | Owner's Manual - Page 62
memory presets in AM, FM1, or FM2. Push the MEM control in CD changer mode (if equipped) to advance to the next disc. VOLUME FM Stereo/Cassette/Single CD Player (CD Changer Compatible) VOL - PUSH ON DISC EJ FM1 ST MUTE AM SEEK TUNE REW FM DOLBY B NR EJ TAPE CD AUTO RDS CLK SCAN FF - 1996 Mercury Villager | Owner's Manual - Page 63
on at a "nominal" listening level when the ignition switch is turned back on. If you wish to maintain your preset volume level, turn the audio system off with the power control before switching off the ignition. AM/FM select The AM/FM select control works in radio, tape and CD modes. AM FM 63 - 1996 Mercury Villager | Owner's Manual - Page 64
to Shuffle feature for more information. Hold the control to continue reversing through the disc. to select the next disc • Press in the CD changer. Hold the control to fast-forward through the remaining discs. Seek function The seek function control works in radio, tape or CD mode. 64 SEEK TUNE - 1996 Mercury Villager | Owner's Manual - Page 65
If a selection has been playing for three seconds or more and you , the CD changer will press replay that selection from the beginning. SEEK • Press to seek forward The scan function works in radio, tape or CD mode. SEEK TUNE SCAN Scan function in radio mode Press the SCAN control to hear a brief - 1996 Mercury Villager | Owner's Manual - Page 66
To stop on a particular selection, press the control again. Scan function in CD mode Press the SCAN control to hear a short sampling of all selections on the CD. (The CD scans in a forward direction, wrapping back to the first track at the end of the CD.) To stop on a particular selection, press the - 1996 Mercury Villager | Owner's Manual - Page 67
available. To deactivate autoset and return to your audio system's manually set memory stations, press the AUTO control again. Bass adjust The bass adjust control allows you to increase or decrease the audio system's bass output. Press the BASS control then press: • to decrease bass output and to - 1996 Mercury Villager | Owner's Manual - Page 68
output and to increase treble output. SEL Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control then press: • to shift sound to the left and to shift sound to the right. • BAL FADE SEL Speaker fade adjust Speaker sound can - 1996 Mercury Villager | Owner's Manual - Page 69
track of the disc will begin playing. After that CD play will begin where it stopped last. If equipped with a CD changer, press the CD control to toggle between single CD and CD changer play. Rewind The rewind control works in tape REW and CD modes. 1 • In tape mode, radio play will continue until - 1996 Mercury Villager | Owner's Manual - Page 70
SHUFFLE mode and plays all tracks on the 6 current disc in random order. If equipped with the CD changer, the shuffle feature continues to the next disc after all tracks on the current disc are played. Press the SHUFFLE control to start this feature. Random order play will continue until the SHUFFLE - 1996 Mercury Villager | Owner's Manual - Page 71
CLK SEL To set the minute, press the RDS/CLK control until SELECT MIN is displayed and press: • • to decrease minutes and to increase minutes. AUTO RDS CLK SEL Radio Data System (RDS) feature When selected, the RDS (Radio AUTO Data System) function performs the RDS following: CLK • Displays the - 1996 Mercury Villager | Owner's Manual - Page 72
feature. SEL RDS traffic announcement When set ON, this traffic feature will AUTO interrupt tape or CD play to play a RDS traffic report broadcast from a FM CLK RDS station. To activate the traffic feature: • Press the RDS control until TRAFFIC is displayed. To see if any stations in your area are - 1996 Mercury Villager | Owner's Manual - Page 73
to mute the playing media. Press the control again to return to the playing media. AUTO RDS CLK SEL EJ MUTE Rear seat controls (if equipped) The Rear Seat Controls (RSC) allow the rear seat passengers to operate the radio, tape, CD, or CD changer (if equipped). VOLUME MEDIA MEM SEEK 73 - 1996 Mercury Villager | Owner's Manual - Page 74
the current volume radio setting. Once in headphone mode, the RSC volume controls will only change volume in the headphones to a desired level and will System The Personal Audio System allows VOLUME MEDIA MEM SEEK the rear seat passengers to listen to one media source (radio, tape, CD, or CD changer - 1996 Mercury Villager | Owner's Manual - Page 75
front passengers. Press the / control again to deactivate headphones (Personal Audio System). Media select Push the MEDIA control to toggle between AM, FM1, FM2, tape, CD, or CD changer (if equipped). VOLUME MEDIA MEM SEEK Memory preset control Push the MEM control successively to allow rear - 1996 Mercury Villager | Owner's Manual - Page 76
Controls and features CD changer (if equipped) The CD changer is located in the center console of your vehicle. 1. Slide the door to access the CD changer magazine. 2. Press to eject the magazine. 3. Turn the magazine (A) over. 4. Using the disc holder release knob (C), pull the disc holder (B) - 1996 Mercury Villager | Owner's Manual - Page 77
Controls and features A If you pull too hard on the disc holder, the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine while pressing on the lever (A). 5. Line up the CD CDs in the changer. The magazine may be stored in the glove box - 1996 Mercury Villager | Owner's Manual - Page 78
damage the unit. Keep the CD changer door closed. Coins and foreign objects will damage the CD player and void your audio system warranty. Do not insert any promotional (odd shaped or sized) discs into the CD changer as that jamming may occur. Troubleshooting the CD changer (if equipped) The laser - 1996 Mercury Villager | Owner's Manual - Page 79
tall buildings between your vehicle's antenna and the radio station signal can cause FM reception problems. Static can be caused on AM stations by power lines, electric fences, traffic lights and thunderstorms. Moving away from an interfering structure (out of its "shadow") returns your reception - 1996 Mercury Villager | Owner's Manual - Page 80
is displayed. The audio system automatically switches to single channel reception if it will improve the reception of a station normally received in stereo. Audio system warranties and service Refer to the "Warranty Guide" for audio system warranty information. If service is necessary, see your - 1996 Mercury Villager | Owner's Manual - Page 81
allows the electrical accessories such as the radio to operate while the engine is not running. 1 3. ON, all electrical circuits operational. Warning lights illuminated. Key position when driving. 4. START, cranks the engine. Release the key as soon as the engine starts. SPEED CONTROL To turn speed - 1996 Mercury Villager | Owner's Manual - Page 82
speed control is switched off, the previously programmed set speed will be erased. To set a speed • Press COAST/SET. For speed control to operate, the speed control you may want to shift to the next lower gear or apply the brakes to reduce your vehicle speed. If your vehicle slows down more than 16 - 1996 Mercury Villager | Owner's Manual - Page 83
hold RES/ACCEL. Release the control when the RES ACCEL desired the accelerator pedal at any time during speed control usage. Releasing the accelerator pedal will return your lower set speed • Press and hold COAST/SET. Release the control when the desired speed is reached or • Press and release - 1996 Mercury Villager | Owner's Manual - Page 84
Controls and features To disengage speed control • Depress the brake pedal. • Press CANCEL. Disengaging the speed control will not erase the previously programmed set speed. RES ACCEL CANCEL COAST SET • Press OFF. Pressing OFF will erase the previously programmed set speed. CRUISE - 1996 Mercury Villager | Owner's Manual - Page 85
48 km/h (30 mph). RES ACCEL CANCEL COAST SET Indicator light This light comes on in the CRUISE instrument cluster when either the COAST/SET or RES/ACCEL controls are pressed. It turns off when the speed control OFF control is pressed, the brake is applied or the ignition is turned to the OFF - 1996 Mercury Villager | Owner's Manual - Page 86
down to activate the left turn signal. • Push up to activate the right turn signal. HI LO F S OFF WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers. When in this position - 1996 Mercury Villager | Owner's Manual - Page 87
. The wiper operates at a pre-set interval. HAZARD RR WASH RR WIPER RR DEFOG SECURITY Press the washer control to activate the rear washer. The wiper will come on when the washer control is pressed, if it is not already on. HAZARD RR WASH RR WIPER RR DEFOG SECURITY HAZARD FLASHER For - 1996 Mercury Villager | Owner's Manual - Page 88
illuminate. The transaxle will operate in all gears except overdrive. To return to normal overdrive mode, press the Transmission Control Switch again. The O/D OFF indicator light will no longer be illuminated. When you shut off and re-start your vehicle, the transaxle will automatically return to - 1996 Mercury Villager | Owner's Manual - Page 89
Controls and features POWER WINDOWS • Press and hold the switch to open. • Pull up and hold the switch to close. AUTO Power vent windows (if equipped) Your vehicle may be equipped with rear power vent windows which are operated the same as the front power windows. AUTO One touch down • Press - 1996 Mercury Villager | Owner's Manual - Page 90
and features Accessory delay With accessory delay, the window and moonroof switches may be used for up to 15 minutes after the ignition switch is turned to the OFF position or until either of the front doors are opened. POWER DOOR LOCKS Push control forward to unlock all doors and pull backward - 1996 Mercury Villager | Owner's Manual - Page 91
and features Pull lock control out to engage the lock. Push control in to disengage childproof locks. POWER SIDE VIEW MIRRORS The ignition must be in ACC or ON position to adjust the power side view mirrors. - 1996 Mercury Villager | Owner's Manual - Page 92
and features 2. Move the control in the direction you wish to tilt the mirror. MIRRORS L R 3. Return to the center position to lock mirrors in place. Heated outside mirrors (if equipped) Both mirrors are that the mat does not interfere with the operation of the accelerator or the brake pedal. 92 - 1996 Mercury Villager | Owner's Manual - Page 93
a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most current transmitters to operate garage doors, entry gates, security systems, entry door locks, and home or office lighting. When programming your - 1996 Mercury Villager | Owner's Manual - Page 94
light will illuminate, indicating the signal is being transmitted). DEL PLAY Rolling code programming Rolling code garage door openers (or other rolling code devices) which are "code protected" and manufactured after 1996, may be determined by the following: • Reference the device owner's manual - 1996 Mercury Villager | Owner's Manual - Page 95
indicator light flashes rapidly and then turns solid after 2 seconds. After completing the "Programming" functions, follow these steps to train a garage door opener with the rolling code feature: 1. Locate the training button on the garage door motor head unit. Refer to the garage door opener manual - 1996 Mercury Villager | Owner's Manual - Page 96
Controls and features 1. Press and hold the desired HomeLink button. Do NOT release until step 4 has been completed. 2. When the indicator light begins to flash slowly (after 20 seconds), position the hand-held transmitter 5-14 cm (2 to 5 inches) away from the HomeLink surface. 3. Press and hold the - 1996 Mercury Villager | Owner's Manual - Page 97
Controls and features To play a message: 1. Press and release the PLAY and release the DEL button while listening to a message or REC DEL PLAY shortly after. The indicator light will flash green twice. 2. To delete all recorded messages, simultaneously press and release the PLAY and REC buttons - 1996 Mercury Villager | Owner's Manual - Page 98
objects. Push in to open or close the cover. Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: • Remove the GARAGE control button from the storage compartment. • Place Velcro on aftermarket transmitter - 1996 Mercury Villager | Owner's Manual - Page 99
located overhead between the driver and passenger seats. The dome lamp will stay on if the control is moved to the ON position. When the control is in the middle position, the lamp will only come on when a door is opened. If the control is moved to the OFF OFF - ON position, the lamp will - 1996 Mercury Villager | Owner's Manual - Page 100
remote entry system allows you to: • lock or unlock all vehicle doors without a key. • activate the panic alarm. If there is any potential remote keyless entry problem with your vehicle, ensure ALL key fobs (remote entry transmitters) are brought to the dealership, to aid in troubleshooting. 100 - 1996 Mercury Villager | Owner's Manual - Page 101
seconds. The hazard lights will flash three times each time the system is toggled between active and non-active modes. If any of the doors are ajar, the horn will not chirp and the lights will not flash. Sounding a panic alarm To activate the alarm, press and hold the PANIC control for longer than - 1996 Mercury Villager | Owner's Manual - Page 102
used to unlock the door(s) or sound the panic alarm. The system automatically turns off after 15 seconds or when the ignition is turned to the RUN position. The inside lights will not turn off if: • they have been turned on with the headlamp control or • any door is open. The battery saver will shut - 1996 Mercury Villager | Owner's Manual - Page 103
(up to four) transmitters yourself: • Unlock, then lock the driver's door using the power door lock switch. • Press any control on the next transmitter to be programmed. All lights (except headlamps) will flash twice to acknowledge acceptance of registration. When ID registration is complete, open - 1996 Mercury Villager | Owner's Manual - Page 104
chirp feature can be turned on/off by holding the LOCK and UNLOCK controls on the transmitter simultaneously for two seconds. The hazard lights will flash three times each time the system is toggled between active and non-active modes. • Open a door and press the power door lock control to lock the - 1996 Mercury Villager | Owner's Manual - Page 105
, the security indicator lamp on the instrument panel will illuminate continuously when the system is prearmed. Once the doors are closed, the system will arm in 30 seconds and the security indicator lamp will begin to flash. HAZARD RR WASH RR WIPER RR DEFOG SECURITY Disarming the anti-theft - 1996 Mercury Villager | Owner's Manual - Page 106
anti-theft system You can disarm the system by any of the following actions: • Press the unlock control. • Unlock the doors with a into lock and turn counterclockwise. Pull back and upward on liftgate handle to fully open liftgate. • The auto-rise feature automatically raises the liftgate or - 1996 Mercury Villager | Owner's Manual - Page 107
Controls and features Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate door or window open, keep the vents open so outside air comes - 1996 Mercury Villager | Owner's Manual - Page 108
Controls and features Front Cargo net The front cargo net can be used to hold small items between the front seats. To install the net, secure - 1996 Mercury Villager | Owner's Manual - Page 109
Controls and features To secure objects on the shelf: 1. Disconnect the net loops from the retainers . Do not load more than 14 kg (30 lbs.) on the parcel shelf. Make sure the rear seat back is in the rearmost/upright position when parcel shelf is loaded. Do not load any objects on the parcel shelf - 1996 Mercury Villager | Owner's Manual - Page 110
following to raise and lower the head restraints. The head restraints can be moved up and down. Push side control and push down on head restraint to lower it. Adjusting the front manual seat Never adjust the driver's seat or seatback when the vehicle is moving. Do not pile cargo higher than - 1996 Mercury Villager | Owner's Manual - Page 111
the seatback can reduce the effectiveness of the seat's safety belt in the event of a collision. Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Adjusting the power seats (if equipped) The power seat controls are located on the outboard side of the seat. Never - 1996 Mercury Villager | Owner's Manual - Page 112
safety restraints Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat's safety belt in the event of a collision. Move the control up or down to move the seat up and down. • 6 way (driver seat - 1996 Mercury Villager | Owner's Manual - Page 113
and mirror to the desired position using the manual controls. 2. Press button 1 or 2 and hold for at least two seconds. The indicator light will stay on until the position is programmed. When the position has been programmed, the indicator light will flash three times. Repeat procedure for second - 1996 Mercury Villager | Owner's Manual - Page 114
is pressed. 3. When the transmitter has been programmed, the indicator will flash five times. The indicator light will remain illuminated until the memory button is pressed again or ten seconds and liquids. • 7 passenger vehicle A. Cargo mat B. Narrow mats C. Sliding door mats, LH/RH A B C 114 - 1996 Mercury Villager | Owner's Manual - Page 115
Seating and safety restraints • 4 passenger vehicle (with third row seat in storage position) A. Cargo mat B. Narrow mats C. Sliding door mats, LH/RH A B C B • 5 passenger vehicle (second row seats removed) A. Cargo mat B. Narrow mats C. Sliding door mats, LH/RH B A B C 115 - 1996 Mercury Villager | Owner's Manual - Page 116
forward position) A. Cargo mat B. Narrow mats A B Stowed cupholders The vehicle is equipped with cupholders that pull out from the 2nd row seat: • Bench seat - below center of the seat cushion 116 - 1996 Mercury Villager | Owner's Manual - Page 117
Seating and safety restraints • Bucket seat (driver's side only) inboard side of seat base Use only soft cups in the cupholder. Hard objects can injure you in a collision. Adjusting 2nd row bench Pull control up to flip seatback to forward flat position. 117 - 1996 Mercury Villager | Owner's Manual - Page 118
seats (if equipped) • Adjusting the left side bucket seat Pull control up to recline the seatback or fold the seatback flat. • Adjusting for easier entry and exit to and from the 3rd row seat. The E-Z Entry system will slide the seat and tip the seatback forward (the seatback must be in the upright - 1996 Mercury Villager | Owner's Manual - Page 119
Seating and safety restraints To exit the third row seat, pull up on the 3rd row access control. To return the seat to a seating position, move the seat rearward until the seat track locks. Then readjust the seatback. Lift handle to move the seat forward or backward. 119 - 1996 Mercury Villager | Owner's Manual - Page 120
Seating and safety restraints Pull control up to flip seatback to a forward flat position. Adjusting 3rd row bench Pull control up to adjust seatback position. This control will also allow the seatback to be put in the forward flat position. 120 - 1996 Mercury Villager | Owner's Manual - Page 121
two storage positions. Before rearranging the seats, remove any floor mats that might be in the way, see Removable floor mats in this chapter for instructions on placement of floor mats. For vehicles equipped with a second row bench seat: If the three passenger bench seat is moved up to the second - 1996 Mercury Villager | Owner's Manual - Page 122
and flip the cushion up. The seat cushion must be moved to the storage position before the seat can be moved along the track. A 2. Pull control (B) to move the seat forward or backward until it locks into position. The seat cushion cannot be lowered if the seat is in a storage position - 1996 Mercury Villager | Owner's Manual - Page 123
the seat. Every time you adjust any seat, check to be sure that it is properly latched belt detach anchor by pushing the release control and lifting upward. 2. From behind the seat, pull up on the release straps located on each side of the seat, releasing the rear floor latches. 3. Lift up the back - 1996 Mercury Villager | Owner's Manual - Page 124
the vehicle. 2. Align seat front hooks to front anchors and push forward into place, lower back of seat into the rear anchors until both rear latches fully engage into place. Be sure that including the driver, should always properly wear their safety belts, even when an air bag SRS is provided. 124 - 1996 Mercury Villager | Owner's Manual - Page 125
for more than one person. Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until - 1996 Mercury Villager | Owner's Manual - Page 126
Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of 8 km - 1996 Mercury Villager | Owner's Manual - Page 127
safety restraints How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety - 1996 Mercury Villager | Owner's Manual - Page 128
of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the safety belt and increase the risk of injury in a collision. Lap belts Adjusting the lap belt The lap belt does not adjust automatically. The lap belts should fit snugly and as low as possible around - 1996 Mercury Villager | Owner's Manual - Page 129
be added to the safety belt assembly by adding a safety belt extension assembly (part number 611C22). Safety belt extension assemblies can be obtained fit of the shoulder belt across the torso. Safety belt warning light and indicator chime The seat belt warning light illuminates in the instrument - 1996 Mercury Villager | Owner's Manual - Page 130
turn off. The safety belt warning light and indicator chime remain off. Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure there are no nicks, wears or cuts, replacing if necessary. All - 1996 Mercury Villager | Owner's Manual - Page 131
(SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim - 1996 Mercury Villager | Owner's Manual - Page 132
objects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causing serious injury. Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. 132 - 1996 Mercury Villager | Owner's Manual - Page 133
. If you must use a forward-facing child seat in the front seat, move the seat all the way back. How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical - 1996 Mercury Villager | Owner's Manual - Page 134
from the air bag module as possible while maintaining vehicle control. Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag is deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the - 1996 Mercury Villager | Owner's Manual - Page 135
sensors), the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors. Determining if the system is operational The SRS uses a readiness light in the instrument cluster to indicate the condition of the system. Refer to the Air bag readiness section in - 1996 Mercury Villager | Owner's Manual - Page 136
the child is the proper size, restrain the child in a safety seat. Children who are too large for child safety seats (as specified by your child safety seat manufacturer) should always wear safety belts. Follow all the important safety restraint and air bag precautions that apply to adult passengers - 1996 Mercury Villager | Owner's Manual - Page 137
the size and weight of the child. Carefully follow all of the manufacturer's instructions with Air Bag Supplemental Restraint System section in this chapter. • Use the correct safety belt buckle for that seating position. • Insert the belt Place seat back in upright position. • Put the safety belt in - 1996 Mercury Villager | Owner's Manual - Page 138
Position the child safety seat in a seat with a combination lap and shoulder belt. An air bag can kill or injure a child in a child seat. If you must use a forward-facing child seat in the front seat, move seat all the way back. Children 12 and under should be properly restrained in the rear seat - 1996 Mercury Villager | Owner's Manual - Page 139
portions together, route the tongue through the child seat according to the child seat manufacturer's instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position - 1996 Mercury Villager | Owner's Manual - Page 140
of the retractor to make sure the retractor is in the automatic locking mode (you should not be able to pull more belt out). If the retractor is not locked, unbuckle the belt and repeat steps two through nine. Check to make sure the child seat is properly secured before each use. 140 - 1996 Mercury Villager | Owner's Manual - Page 141
with a passenger air bag deactivate switch and the switch is turned to "OFF." When using forward-facing child safety seats in vehicles with only two seating positions so the forward-facing child safety seat cannot be placed in the rear of the vehicle, move the passenger seat as far back from the - 1996 Mercury Villager | Owner's Manual - Page 142
child seat position 3-passenger/2nd row -Outboard 3-passenger/2nd row -Center Tether to...Reference Section Floor anchor directly 3rd row seats behind child rear of 2nd row seats the second row seats Tongue of 3rd row belt directly behind child seat position CANNOT BE TETHERED 3rd row bench in 2nd - 1996 Mercury Villager | Owner's Manual - Page 143
Seating and safety restraints Second row seats 1. Position the child safety seat on the passenger seat cushion. 2. Route the child safety seat tether strap over the back of the seat. 3. Grasp the tether strap and position it to the seat frame. 143 - 1996 Mercury Villager | Owner's Manual - Page 144
Seating and safety restraints 4. Rotate the tether strap. 5. Clip the tether strap to the seat tether slot bracket at the lower rear portion of the seatback. If the tether strap is clipped incorrectly (as shown) the child safety seat may not be retained properly in the event of a collision. 144 - 1996 Mercury Villager | Owner's Manual - Page 145
Seating and safety restraints 6. Rotate the tether strap clip. 7. Refer to the instructions in this section under Installing child safety seats in combination lap and shoulder belt seating positions to secure the child safety seat. 8. Tighten the child safety seat tether strap according to the - 1996 Mercury Villager | Owner's Manual - Page 146
position (third row seat only) with a tether anchorage hardware kit. Tether anchorage hardware kits (part number 613D20) including instructions, may be obtained at no charge from any Ford or Lincoln-Mercury dealer. All vehicles built for sale in Canada include a tether anchor hardware kit. Be sure - 1996 Mercury Villager | Owner's Manual - Page 147
sure it is securely held in place. 7. Check that the retractor is in automatic locking mode by trying to pull more belt out of the retractor. If you cannot pull any more belt webbing out of the retractor, the belt is in automatic locking mode. 8. Check to make sure the child restraint is properly - 1996 Mercury Villager | Owner's Manual - Page 148
. This child seat conforms to all Federal and local motor vehicle safety standards. Read the labels located on the repair. The belts will not snug during a collision. Placing your child in the built-in child seat Failure to follow all of the instructions on the use of this child restraint system - 1996 Mercury Villager | Owner's Manual - Page 149
Seating and safety restraints 1. Pull the release strap near the bottom of the seatback. 2. Grasp the child seat at the top of the seatback and pull the top forward to release the latch. 3. Continue to unfold the child seat until it rests on the seat. 149 - 1996 Mercury Villager | Owner's Manual - Page 150
buckle (it doesn't matter which tongue is inserted first). Insert other tongue. The color green must appear in the indicator window on the crotch safety belt buckle when buckled. Allow belts to retract and fit snugly. 8. Fasten both halves of the chest clip below the child's shoulders and adjust - 1996 Mercury Villager | Owner's Manual - Page 151
belts off the child's shoulders and remove the child. To stow the built-in child seat Return the child seat cushion to the upright position, then press firmly in the center in use during a collision, Ford recommends replacing it. Built-in child restraints not in use during a collision should be - 1996 Mercury Villager | Owner's Manual - Page 152
exhaust fumes. Important safety precautions A computer system controls the engine's idle revolutions per minute (RPM). When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically, have the vehicle checked. Do not allow the vehicle to - 1996 Mercury Villager | Owner's Manual - Page 153
2. Make sure the headlamps and vehicle accessories are off. 3. Make sure the parking brake is set. FUSES 4. Make sure the 120 E FUEL 000000 FUEL DOOR N O R M A L H C TEMP 0 0 0 0 1 0 AIR BAG 20 160 km/h RPMx1000 8 100 MPH UNLEADED FUEL ONLY SERVICE ENGINE SOON ! P BRAKE R N D 2 1 - 1996 Mercury Villager | Owner's Manual - Page 154
km FUEL DOOR 1/2 N O R M A L E C UNLEADED FUEL ONLY ABS SERVICE ENGINE SOON AIR BAG ! P BRAKE P R N D 2 1 O/D OFF Make sure the corresponding lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced. • If the driver's safety belt is fastened, the light may not - 1996 Mercury Villager | Owner's Manual - Page 155
are harmful and could kill you. Have the exhaust and body ventilation systems checked whenever: • the vehicle is raised for service. • the sound of the exhaust system changes. • the vehicle has been damaged in a collision. Engine exhaust, some of its constituents, and certain vehicle components - 1996 Mercury Villager | Owner's Manual - Page 156
ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning to bring in fresh air. Improve vehicle ventilation by keeping all air inlet vents clear of - 1996 Mercury Villager | Owner's Manual - Page 157
" sound is present while braking, the brake linings may be worn-out and should be inspected by a qualified service technician. Anti-lock brake system (ABS) (if equipped) On vehicles equipped with an anti-lock braking system (ABS), a noise from the hydraulic pump motor and pulsation in the pedal - 1996 Mercury Villager | Owner's Manual - Page 158
on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock ! P brake system is disabled and normal braking is still effective unless the BRAKE brake warning light also remains illuminated with parking brake released. (If your brake warning lamp illuminates, have - 1996 Mercury Villager | Owner's Manual - Page 159
downward again to release the parking brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel system breaks down (or if the engine is turned off), you can steer the vehicle manually, but it takes more effort. If the steering wanders or pulls, the condition - 1996 Mercury Villager | Owner's Manual - Page 160
gears, stopping between shifts, in a steady pattern. Press lightly on the accelerator in each gear. Do not rock the vehicle for more than a few minutes. The transmission and tires may be damaged or the engine may overheat. Always set the parking brake fully and make sure the gearshift is latched in - 1996 Mercury Villager | Owner's Manual - Page 161
conditions, your automatic transaxle electronically controls battery. When the battery is disconnected or a new battery is brake pedal down while in this position. N D 2 1 R N D 2 1 Overdrive - column mounted gearshift with O/D off switch The Overdrive position with the O/D P R N D 2 OFF switch - 1996 Mercury Villager | Owner's Manual - Page 162
vehicle. If the condition still exists, contact your dealer as soon as possible. If the O/D OFF indicator light is flashing on and off repeatedly when the vehicle is started or does not come on when the O/D OFF control is pressed, there may be a transaxle electronic system malfunction. You should - 1996 Mercury Villager | Owner's Manual - Page 163
more engine braking than Overdrive for descending hills or city driving. To return the transaxle to the normal Overdrive operation, press the O/D OFF control again. Use this control to select between Overdrive or D (O/D OFF) whenever you drive your vehicle. If the O/D OFF indicator light is flashing - 1996 Mercury Villager | Owner's Manual - Page 164
the O/D OFF switch depressed. Driving with the gearshift lever in D (Overdrive) gives the best fuel economy for normal driving conditions. For manual control, start in 1 (First) and then shift manually. To put your vehicle in gear, start the P R N D 2 1 engine, depress the brake pedal, then move - 1996 Mercury Villager | Owner's Manual - Page 165
Compliance Label on the driver's door pillar. • GAWR (Gross Axle Weight Rating) : Carrying capacity for each axle system. The GAWR is specific to rating is determined by subtracting the vehicle curb weight for each engine/transmission combination, any required option weight for trailer towing and - 1996 Mercury Villager | Owner's Manual - Page 166
the vehicle's GVWR and GAWR limitations. Replacement tires with a higher limit than the on the inside pillar of the driver's door, lists several important vehicle weight rating limitations engine damage, transmission/axle damage, structural damage, loss of control, and personal injury. 166 - 1996 Mercury Villager | Owner's Manual - Page 167
Package is recommended for towing of any trailer since it provides a heavy duty battery, conventional size spare tire and wiring. Trailer towing puts additional loads on your vehicle's engine, transmission, axle, brakes, tires, and suspension. For your safety and to maximize vehicle performance, be - 1996 Mercury Villager | Owner's Manual - Page 168
slack for turning corners. If you use a rental trailer, follow the instructions that the rental agency gives to you. Do not attach safety chains to the bumper. Trailer brakes Electric brakes and manual, automatic or surge-type brakes are safe if installed properly and adjusted to the manufacturer - 1996 Mercury Villager | Owner's Manual - Page 169
km (50 miles), thoroughly check your hitch, electrical connections and trailer wheel lug nuts. • When stopped in traffic for long periods of time in hot weather, place the gearshift in P (Park) and increase idle speed. This aids engine cooling and air conditioner efficiency. • Vehicles with trailers - 1996 Mercury Villager | Owner's Manual - Page 170
Driving LUGGAGE RACK The front and rear crossbar can be adjusted to fit the item being carried. Do not load more than 44 kg (100 lbs.) on the luggage rack. To adjust cross-bar position: 1. Loosen the thumbwheel at both ends of the cross-bar. 2. Slide the cross-bar to the desired location. 3. Tighten - 1996 Mercury Villager | Owner's Manual - Page 171
the instrument panel. HAZARD • Depress hazard lights control to activate all hazard flashers simultaneously. RR WASH RR WIPER • Depress control again to turn the flashers off. RR DEFOG SECURITY RESETTING THE FUEL PUMP SHUT-OFF SWITCH After a collision, if the engine cranks but does not start, the - 1996 Mercury Villager | Owner's Manual - Page 172
position. 5. Make a further check for leaks in the fuel system. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components - 1996 Mercury Villager | Owner's Manual - Page 173
Roadside emergencies Standard fuse amperage rating and color COLOR Fuse Rating 2A 3A 4A 5A 7.5A 10A 15A fuse panel The fuse panel is located below and to the left of the steering wheel by the brake pedal. Remove the panel cover to access the fuses. To remove a fuse use the fuse puller tool provided - 1996 Mercury Villager | Owner's Manual - Page 174
20A FRONT BLOWER 7.5A 20A IGN IGN 10A 10A ELECTRON 20A IGN BAT 20A FRONT BLOWER 10A Control (EATC) Module, Instrument Cluster, Rear Wiper Motor Assembly Rear Exterior Lamps Airbag Diagnostic Monitor Radio, Rear Radio Control, CD Changer Powertrain Control Module, Oxygen Sensors Tail Lamp Air Bag - 1996 Mercury Villager | Owner's Manual - Page 175
(SEC), Power Mirror Switch Brake Pedal Position (BPP) Switch, Trailer Tow Control Unit Cigar Lighter Hazard Warning Flasher Switch, Anti-Theft Indicator Rear Powerpoint Rear Blower Motor Relay, Rear Blower Motor Front Wiper/Washer Assembly Rear Blower Motor Relay, Rear Blower Motor Rear Wiper/Washer - 1996 Mercury Villager | Owner's Manual - Page 176
Amp Rating 10A Description Transmission Control, Lighting Control Module, ABS Control Module, Smart Entry Control (SEC)/Timer Module Rear Window Defrost Front Blower Motor, Front Blower Motor/Speed Controller Rear Window Defrost Not Used Rear Window Defrost Switch, Power/Heated Mirrors Rear Defog - 1996 Mercury Villager | Owner's Manual - Page 177
LINKS ONLY 15A 65A FR BLW 30A PWR WND 40A ABS 20A 7.5A SEC ALT HORN ABS 100A 140A MAIN ALT 45A 75A RR RAD DEF FAN coded as follows. Fuse/Relay Location - FUEL PUMP INJ SEC RAD ECCS - - ALT Fuse Amp Rating - 15A* 10A* 7.5A* 7.5A* 10A* - - 10A* Description Not Used Fuel Pump Relay Powertrain Control - 1996 Mercury Villager | Owner's Manual - Page 178
Lighting Control Module Not Used Not Used ABS Control Module Not Used Power Window Relay, Smart Entry Control (SEC)/Timer Module, Power Seats Low Speed Fan Control Relay Not Used Ignition Switch Not Used High Speed Fan Control Relay Front Blower Motor Relays Rear Window Defroster Relay Accessory - 1996 Mercury Villager | Owner's Manual - Page 179
Relay box The relay box is located in the engine compartment in front of the battery. 1 2 3 4 5 The relays are coded as follows: Relay location 1 2 3 4 5 6 7 6 7 Description Start Inhibit Relay Fuel Pump Relay Bulb Check Relay Speed Control Hold Relay Anti-theft Relay Horn Relay A/C Relay - 1996 Mercury Villager | Owner's Manual - Page 180
Replace this tire with a full-size tire as soon as possible. If you use the temporary spare tire continuously or do not follow these precautions, the tire could fail, causing you to lose control reduced ground clearance • try to repair the bag Removing the jack and tools 1. Lift the - 1996 Mercury Villager | Owner's Manual - Page 181
hex nut. 2. Insert the lug nut wrench on the hex nut in cargo floor. 3. Turn the wrench counterclockwise until tire is lowered to the ground and the cable is slightly slack. 4. Remove the retainer from the spare tire. It may be necessary to lift one end of the tire to disengage the - 1996 Mercury Villager | Owner's Manual - Page 182
position of tire for looseness against the underbody supports and retighten if necessary. Ensure the position of the tire is not too far forward to avoid contact with the axle. Tire change procedure When one of the front wheels is off the ground, the transaxle alone will not prevent the vehicle - 1996 Mercury Villager | Owner's Manual - Page 183
flashers and set parking brake. FUSES 2. Place gearshift lever in P (Park), turn engine OFF, and block the diagonally opposite wheel. 3. Remove the spare tire and jack assembly. 4. Remove the center ornament or wheel cover but do not remove them until the wheel is raised off the ground. 183 - 1996 Mercury Villager | Owner's Manual - Page 184
ground. To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. 8. Remove the lug nuts with the lug wrench. 9. Replace cover or center 3 4 - 1996 Mercury Villager | Owner's Manual - Page 185
. You could damage the catalytic converter. Batteries contain sulfuric acid which can brake on both vehicles and stay clear of the engine cooling fan and other moving parts. 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps - 1996 Mercury Villager | Owner's Manual - Page 186
Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive - 1996 Mercury Villager | Owner's Manual - Page 187
(-) cable to an exposed metal part of the stalled vehicle's engine, away from the battery and the carburetor/fuel injection system. The preferred locations of an exposed metal part (to ground the circuit) are the alternator mounting brackets or an engine lifting eye. Do not use fuel lines, engine - 1996 Mercury Villager | Owner's Manual - Page 188
vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. 2. Remove the jumper - 1996 Mercury Villager | Owner's Manual - Page 189
of the booster vehicle's battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle's battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions - 1996 Mercury Villager | Owner's Manual - Page 190
service or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor transmission. Ford Motor Company provides a towing manual for all authorized tow truck operators. Have your - 1996 Mercury Villager | Owner's Manual - Page 191
lit material away from the battery and all fuel related parts. If you disconnect the battery, the engine must "relearn" its idle conditions before your vehicle will drive properly, as explained in Battery in this chapter. Working with the engine off 1. Set the parking brake and ensure the gearshift - 1996 Mercury Villager | Owner's Manual - Page 192
remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. 3. Lift - 1996 Mercury Villager | Owner's Manual - Page 193
and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.3L V6 engine 10 9 11 1 2 3 8 7 6 5 4 1. Power distribution box 2. Brake fluid reservoir 3. Air filter assembly 4. Battery 5. Relay box 6. Engine oil filler cap 7. Engine oil dipstick 8. Windshield washer fluid reservoir - 1996 Mercury Villager | Owner's Manual - Page 194
care ENGINE OIL Checking the engine oil Refer to the Scheduled Maintenance Guide for the appropriate intervals for checking the engine oil . 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and - 1996 Mercury Villager | Owner's Manual - Page 195
is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity. Remove the engine oil filler cap and use a funnel to - 1996 Mercury Villager | Owner's Manual - Page 196
unnecessary and could, under certain conditions, lead to engine damage which is not covered by your warranty. Change your engine oil and filter according to the appropriate schedule listed in the Scheduled Maintenance Guide. It is recommended that you replace the engine oil drain plug washer each - 1996 Mercury Villager | Owner's Manual - Page 197
Maintenance and care BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed. Refer to the Scheduled Maintenance Guide for the service interval schedules: 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir. 2. - 1996 Mercury Villager | Owner's Manual - Page 198
Do not put washer fluid in the reservoir for the engine coolant Checking and adding washer fluid for the liftgate Washer fluid for the liftgate is supplied by the same reservoir as the windshield. ENGINE COOLANT Your engine's cooling system has been factory-filled with a 50/50 mixture of distilled - 1996 Mercury Villager | Owner's Manual - Page 199
fluid level and concentration to work properly. If the engine coolant fluid level and concentration is not maintained correctly, damage to the engine and cooling system may result . When the engine is cold, check the level of the engine coolant in the reservoir. • The engine coolant should be at the - 1996 Mercury Villager | Owner's Manual - Page 200
will decrease the freeze protection characteristics of the engine coolant and may cause engine damage. Plain water may be added in an emergency, but you must replace it with a 50/50 mixture of engine coolant and distilled water as soon as possible. Check the coolant level in the reservoir before you - 1996 Mercury Villager | Owner's Manual - Page 201
begins to release. 3. Step back while the pressure releases. 4. When you are sure that all the pressure has been released, use the cloth to turn it counterclockwise and remove the cap. Recycled engine coolant Ford Motor Company recommends the use of recycled engine coolant produced by Ford-approved - 1996 Mercury Villager | Owner's Manual - Page 202
it reaches the range between the MIN and MAX lines. Be sure to put the cap back on the reservoir. TRANSMISSION FLUID Checking automatic transmission fluid Refer to your Scheduled Maintenance Guide for scheduled intervals for fluid checks and changes. Your transaxle does not consume fluid. However - 1996 Mercury Villager | Owner's Manual - Page 203
fluid to cool before checking. 1. Drive the vehicle 30 km (20 miles) or until it reaches normal operating temperature. 2. Park the vehicle on a level surface and engage the parking brake. 3. With the parking brake engaged and your foot on the brake pedal, start the engine and move the gearshift - 1996 Mercury Villager | Owner's Manual - Page 204
An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. AIR FILTER MAINTENANCE Refer to the Scheduled Maintenance Guide for the appropriate intervals for changing the air filter element. For information on replacement air filter elements, refer - 1996 Mercury Villager | Owner's Manual - Page 205
. 5. Replace the air filter housing cover and secure the four clamps. BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery - 1996 Mercury Villager | Owner's Manual - Page 206
often, have the charging system checked. If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened - 1996 Mercury Villager | Owner's Manual - Page 207
dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. RE LE AD R TU N RECYCLE ODOR AND PARTICULATE AIR FILTRATION SYSTEM (IF EQUIPPED) 207 - 1996 Mercury Villager | Owner's Manual - Page 208
• Improves the interior compartment cleanliness • Protects the climate control components from particle deposits The filter is located just in front of the windshield under the cowl grille on the passenger side of the vehicle. To replace the filter, perform the following procedure: 1. Remove both - 1996 Mercury Villager | Owner's Manual - Page 209
the four (4) screw anchors by pushing upward on the screw anchor. 5. Disconnect the windshield washer hose at the Y connector at the rear corner of the engine compartment. 6. Lift the cowl grille from the vehicle. 7. Locate the cabin air filter on the passenger side of the vehicle. 209 - 1996 Mercury Villager | Owner's Manual - Page 210
four (4) screws from the top surface of the cabin air filter top cover. 9. Remove the cover. 10. Remove the filter element by pulling forward on the top surface of the filter and lifting. B 11. Install the new filter (A) element into the filter retaining frame (B). Ensure that you insert the three - 1996 Mercury Villager | Owner's Manual - Page 211
arm blade onto the windshield surface. WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin manually - 1996 Mercury Villager | Owner's Manual - Page 212
49 Code of Federal Regulations Part 575 service practices, and differences in road characteristics and climate. Traction AA A B C The traction grades, from highest to lowest are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pavement as measured under controlled conditions - 1996 Mercury Villager | Owner's Manual - Page 213
Motor Vehicle control. Tire rotation Because your vehicle's tires perform different jobs, they often wear differently. To make sure your tires wear evenly and last longer, rotate them as indicated in the Scheduled Maintenance Guide. If you notice that the tires wear unevenly, have them checked - 1996 Mercury Villager | Owner's Manual - Page 214
the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity. Use only the - 1996 Mercury Villager | Owner's Manual - Page 215
easier for the driver to lose control and roll over. Tires that are Snow tires must be the same size and grade as the tires you and snow. However, in some climates, you may need to use snow tires the chains do not touch any wiring, brake lines or fuel lines. • Drive cautiously. If you hear the - 1996 Mercury Villager | Owner's Manual - Page 216
may spray out and injure you or others. If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel system to work improperly in a collision, which may result in possible personal injury. Automotive fuels can cause serious - 1996 Mercury Villager | Owner's Manual - Page 217
engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions when filling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the - 1996 Mercury Villager | Owner's Manual - Page 218
If the "Service Engine Soon" indicator comes on and stays on when you start the engine, the fuel filler cap may not be properly installed. Turn off the engine, remove the cap, align the cap properly and reinstall it. If you must replace the fuel filler cap, replace it with a fuel filler cap that is - 1996 Mercury Villager | Owner's Manual - Page 219
areas. Do not be concerned if your engine sometimes knocks lightly. However, if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating, see your dealer or a qualified service technician to prevent any engine damage. 87 Fuel quality If you are - 1996 Mercury Villager | Owner's Manual - Page 220
filter replacement, see your dealer or a qualified service technician. Refer to the Scheduled Maintenance Guide for the appropriate intervals for changing the fuel filter. Replace the fuel filter with an authorized Motorcraft part. The customer warranty may be void for any damage to the fuel system - 1996 Mercury Villager | Owner's Manual - Page 221
record the type of driving (city or highway). This will provide an accurate estimate of the vehicle's fuel economy under current driving conditions. Additionally, keeping records during summer and winter will show how temperature impacts fuel economy. In general, lower temperatures give lower fuel - 1996 Mercury Villager | Owner's Manual - Page 222
% less fuel than traveling at 105 km/h [65 mph]). • Revving the engine before turning it off may reduce fuel economy. • Using the air conditioner or defroster may reduce fuel economy. • You may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear - 1996 Mercury Villager | Owner's Manual - Page 223
. Your fuel economy may vary depending upon the method of operation and conditions. EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards. To make - 1996 Mercury Villager | Owner's Manual - Page 224
replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability. Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine - 1996 Mercury Villager | Owner's Manual - Page 225
the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of engine until step seven is completed. EXTERIOR BULBS Replacing exterior bulbs It is a good idea to check the operation of the following lights - 1996 Mercury Villager | Owner's Manual - Page 226
lamp housings and affect performance. Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position, then Without turning, remove the old bulb from its socket by gently pulling it straight back out of the lamp assembly. To install the new bulb: Handle a halogen - 1996 Mercury Villager | Owner's Manual - Page 227
snaps, locking it into position. 4. Turn the headlamps on and make sure they work properly. If the headlamp was correctly aligned before you changed the bulb, you should not need to align it again. Replacing front cornering/side marker lamp bulbs 1. Remove screw from the lamp assembly. 2. Disengage - 1996 Mercury Villager | Owner's Manual - Page 228
assembly. 3. Pull bulb straight out of socket and push in the new bulb. 4. To complete installation, follow removal procedure in the reverse order. Replacing tail lamp/backup/turn signal lamp bulbs 1. Open the liftgate to expose the lamp assemblies. 2. Remove the two screws from the lamp assembly - 1996 Mercury Villager | Owner's Manual - Page 229
Maintenance and care Replacing license plate lamp bulbs 1. Remove two screws, grommets and the license plate lamp assembly from the liftgate. 2. Remove bulb socket by turning counterclockwise. 3. Carefully pull - 1996 Mercury Villager | Owner's Manual - Page 230
4 194 Glove compartment 1 194 All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your dealer. AIMING THE HEADLAMPS The alignment of your headlamps should be checked by a qualified service technician if: • Oncoming motorists frequently signal - 1996 Mercury Villager | Owner's Manual - Page 231
Acrylic Spray Lacquer (#ALAZ-19500-XXXXA) from the Ford Car Care Chemicals line. Please note that the part numbers (shown as XXXX above) will vary with your vehicle's specific coloring. Observe the application instructions on the products. Remove particles such as bird droppings, tree sap, insect - 1996 Mercury Villager | Owner's Manual - Page 232
. The high pressure fluid could penetrate the sealed parts and cause damage. • Do not spray with cold water to avoid cracking the engine block or other engine components. • Never apply anything to the drive belt (including belt dressing). • Cover the highlighted areas to prevent water damage when - 1996 Mercury Villager | Owner's Manual - Page 233
rear windshield and wiper blades should be cleaned on a regular basis, and blades or rubber elements replaced when worn. Cleaning the instrument panel Clean with a damp cloth, then dry with a dry complete underside of vehicle frequently. Keep body drain holes unplugged. Inspect for road damage. 233 - 1996 Mercury Villager | Owner's Manual - Page 234
the safety belt webbing or damage the vinyl parts of the seat. The child seat liner is removable and may be machine-washed and air dried. Cleaning Do not bleach or dye the belts, because these actions may weaken the belt webbing. Check the safety belt system periodically to make sure there are - 1996 Mercury Villager | Owner's Manual - Page 235
A/C. Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information. REFILL CAPACITIES Fluid Engine oil (includes filter change) Brake fluid Ford Part Name Motorcraft SAE 5W-30 Super Premium Motor Oil High Performance DOT 3 Motor Vehicle Brake Fluid Motorcraft MERCON ATF - 1996 Mercury Villager | Owner's Manual - Page 236
name High Performance DOT 3 Motor Vehicle Brake Fluid Silicone Lubricant Ford Premium Engine Coolant Ford part number C6AZ-19542-AB Ford specification ESA-M6C25-A and DOT 3 Door weatherstrips Engine coolant Engine oil Motorcraft SAE 5W-30 Super Premium Motor Oil Door latch, hood Multi-Purpose - 1996 Mercury Villager | Owner's Manual - Page 237
Item Disc brake caliper rails Ford part name Silicone Brake Caliper Grease and Dielectric Compound CV Joint Grease (High Temp.) Ultra-clear Windshield Washer Concentrate Ford part Ford number specification D7AZ-19A331-A ESE-M1C171-A (Motorcraft WA-10) E43Z-19590-A C9AZ-19550-AC ESP-M1C207 - 1996 Mercury Villager | Owner's Manual - Page 238
Capacities and specifications VEHICLE DIMENSIONS Vehicle dimensions (1) Overall length (2) Overall width (3) Overall height (with luggage rack) (4) Wheelbase (5) Track - Front (5) Track - Rear mm (in) 4 945.4 (194.7) 1 902.5 (74.9) 1 780.5 (70.1) 2 849.9 (112.2) 1 610.4 (63.4) 1 610.4 (63.4) 3 5 2 - 1996 Mercury Villager | Owner's Manual - Page 239
Label is located on the front door latch pillar on the driver's side. MFD. BY FORD MOTOR CO. DATE: XX/XX GVWR: MOTOR VEHICLE SAFETY STANDARDS IN EFFECT ON THE DATE OF MANUFACTURE SHOWN ABOVE. VIN: XXXXXXXXXXXXXXXXX TYPE: XXX EXT PAINT COLORS: XX XX RC: XX DSO: G DRK INT TR TP/PS R AXLE - 1996 Mercury Villager | Owner's Manual - Page 240
. (Please note that in the graphic XXXX is representative of your vehicle identification number.) AIR BAG II XXXXXXXXXXXXXXXXX Engine and transmission serial number The engine serial number is stamped on the engine block, and the transmission serial number is on the transmission case. 240 - 1996 Mercury Villager | Owner's Manual - Page 241
from the New Vehicle Limited Warranty. The service is available: • 24-hours, seven days through the Ford Auto Club by contacting your Ford or Lincoln-Mercury dealer. Roadside assistance Owner Guide portfolio in the glove compartment in Ford vehicles and is mailed to you if you own a Mercury or - 1996 Mercury Villager | Owner's Manual - Page 242
, please be aware that some dealers offer service contracts that are not backed by Ford Motor Company or Ford of Canada. On the surface, many independent plans appear to be like Ford's. The problem is that they can often require the use of non-factory approved parts and have much more complex and - 1996 Mercury Villager | Owner's Manual - Page 243
resolved at this level. Ford Motor Company and Ford of Canada dealerships also carry genuine Ford parts and accessories, providing you with original equipment reliability. Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more - 1996 Mercury Villager | Owner's Manual - Page 244
service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Assistance Center to find an authorized dealership to help you. In the United States: Ford Motor Company Customer Assistance Center before pursuing replacement or - 1996 Mercury Villager | Owner's Manual - Page 245
this service without notice and without incurring obligations per applicable state law. What kinds of cases does the Board review? Unresolved warranty repair concerns or vehicle performance as designed concerns on Ford/Mercury and Lincoln cars and Ford/Mercury and Lincoln light trucks which - 1996 Mercury Villager | Owner's Manual - Page 246
Ford and Lincoln-Mercury dealership management, repair(s) and mileage at the time of occurrence(s) • the current mileage • the name of the dealer(s) who sold or serviced the vehicle • a brief description of your unresolved concern • a brief summary of the action taken by the dealer(s) and Ford Motor - 1996 Mercury Villager | Owner's Manual - Page 247
You may also contact the North American Customer Assistance Center at 1-800-392-3673 (Ford), TDD for the hearing impaired: 1-800-232-5952 or by writing to the Center at the following address: Ford Motor Company Customer Assistance Center 16800 Executive Plaza Drive P.O. Box 6248 Dearborn, Michigan - 1996 Mercury Villager | Owner's Manual - Page 248
emission control system and may cause engine knocking or serious engine damage. Ford Motor serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR - 1996 Mercury Villager | Owner's Manual - Page 249
be sold with the Motorcraft name A wide selection of Ford accessories are available for your vehicle through your local authorized Ford, Lincoln-Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to - 1996 Mercury Villager | Owner's Manual - Page 250
and convenience Air conditioner Air filtration systems Cargo nets Cargo organizers Cargo shades Cargo trays Dash trim Engine block heaters Gear shift knob Luggage presenter (Continental only) Manual sliding rear window Tire step Travel equipment Console Console armrest Daytime running lights Factory - 1996 Mercury Villager | Owner's Manual - Page 251
Customer assistance Soft luggage cover Speed control Towing mirrors Trailer hitch Trailer hitch bars and balls Trailer hitch wiring adaptor Protection and appearance equipment Air bag anti-theft locks Bed mat/bedliner tailgate covers Bed mats Bedliners Car/truck covers Cargo liners, interior Carpet - 1996 Mercury Villager | Owner's Manual - Page 252
be installed only by a qualified service technician. • Mobile communications systems may harm the operation of your vehicle, particularly if they are not properly designed for automotive use or are not properly installed. When operated, such systems may cause the engine to stumble or stall. In - 1996 Mercury Villager | Owner's Manual - Page 253
the publications in this portfolio in the United States: Make checks payable to: HELM, INCORPORATED P.O. Box 07150 Detroit, Michigan in this portfolio in Canada: Make cheques payable to: Ford Motor Company of Canada, Ltd. Service Publications P.O. Box 1580, Station B Mississauga, Ontario, Canada - 1996 Mercury Villager | Owner's Manual - Page 254
of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424-9393 (202-366-0123 in the Washington D.C. area) or - 1996 Mercury Villager | Owner's Manual - Page 255
driver air bag ...133 indicator light ...6,135 operation ...133 passenger air bag ...133 Air cleaner filter ...204,205,235 Air conditioning ...21 automatic temperature control system ...29 Air filter, cabin ...207 Anti-theft system ...104 arming the system ...104 disarming a triggered system ...105 - 1996 Mercury Villager | Owner's Manual - Page 256
Defrost rear window ...39 Dipstick engine oil ...194 Doors door ajar warning ...7 Driving under special conditions through water ...164 Emergencies, roadside jump-starting ...185 Emission control system ...223 Engine ...237,238 check engine/service engine soon light ...9 coolant ...198 idle speed - 1996 Mercury Villager | Owner's Manual - Page 257
106 Lights, warning and indicator ...6 air bag ...6 anti-lock brakes (ABS) ...8,158 brake ...7 charging system ...6 cruise indicator ...8 door ajar ...7 high beam ...7 low fuel ...8 low washer fluid ...10 oil pressure ...7 overdrive off ...10 safety belt ...7 service engine soon ...9 speed control - 1996 Mercury Villager | Owner's Manual - Page 258
...236,237 Radio ...40 Relays ...172,179 Remote entry system ...100,101 illuminated entry ...102 locking/unlocking doors ...101 panic alarm ...101 replacement/additional transmitters ...103 replacing the batteries ...102 Roof rack ...170 Safety belts (see Safety restraints) ...124,125,126,127,128 - 1996 Mercury Villager | Owner's Manual - Page 259
Index Warning chimes ...10,11 Warning lights (see Lights) ...6 Washer fluid ...198 Water, Driving through ...164 Windows power ...89 rear wiper/washer ...87 Windshield washer fluid and wipers ...87 checking and cleaning ...211 operation ...86 replacing wiper blades ...211 Wrecker towing ...190 259 - 1996 Mercury Villager | Owner's Manual - Page 260
260 - 1996 Mercury Villager | Owner's Manual - Page 261
261 - 1996 Mercury Villager | Owner's Manual - Page 262
262 - 1996 Mercury Villager | Owner's Manual - Page 263
263 - 1996 Mercury Villager | Owner's Manual - Page 264
tank capacity 75.7L (20.0 gallons) Engine oil capacity (includes filter 4.0L (4.2 quarts). Use Motorcraft change) SAE 5W-30 Super Premium Motor Oil, Ford specification WSS-M2C153-G. Tire size and pressure Refer to the Certification Label on inside of driver's door. Hood release Pull handle under the
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
 |
 |
Before driving
Introduction
2
Instrumentation
3
Controls and features
19
Seating and safety restraints
110
Starting and driving
Starting
152
Driving
157
Roadside emergencies
171
Servicing
Maintenance and care
191
Capacities and specifications
235
Customer assistance
241
Reporting safety defects
254
Index
255
All rights reserved. Reproduction by any means, electronic or mechanical
including photocopying, recording or by any information storage and retrieval
system or translation in whole or part is not permitted without written
authorization from Ford Motor Company.
Copyright
r
1999 Ford Motor Company
Contents
1