1998 Mercury Mountaineer Owner Guide 1st Printing

1998 Mercury Mountaineer Manual

Get 1998 Mercury Mountaineer PDF manuals and user guides View all 1998 Mercury Mountaineer manuals

1998 Mercury Mountaineer manual content summary:

  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 1
    restraints Starting and driving Starting Driving Roadside emergencies Servicing Maintenance and care Capacities and specifications Reporting information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Copyright
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 2
    1 600 km (1 000 miles) of driving, vary speeds frequently. This is necessary to give the moving parts a chance to break in. If possible, you should avoid full use of the brakes for the first 1 600 km (1 000 miles). INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 3
    this Owner's Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or an accident. Be sure to read Driving off road in the Driving chapter as well as the "Four Wheeling" supplement included
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 4
    140 30 20 10 20 H 90 180 0 0 0 0 0 0 160 100 110 200 F E 0 H OFF RSM ON SET ACC OFF COAST SRS Headlamp control (pg. 16) Tilt steering wheel lever (pg. 31) Turn signal and wiper/washer control (pg. 25) Instrument panel dimmer switch (pg. 17) Driver side
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 5
    sound system; refer to Audio Guide Gearshift (includes overdrive button) (pg. 104) Rear window/washer control (pg. 32) Rear window defroster control (pg. 24) OD ON/OFF VOL - PUSH ON AM FM BASS TREB FM 1 CLK BAL FADE AUTO SET PUSH SEEK TUNE DISCS SCAN EJ DOLBY SYSTEM TAPE CD REW
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 6
    LIGHTS AND CHIMES CHECK GAGE DOOR AJAR 4 H CHECK ENGINE 5 6 40 30 20 10 50 60 60 70 0 0 0 80 100 120 140 80 90 160 3 2 1 RPMx1000 C 40 000000 100 1 10 H L H SPEED CONT 4WD HIGH 4WD LOW 20 180 FUEL RESET F E ABS 0 ! BRAKE MPH km/h 120 THEFT P R N D 2 1 L O/D OFF Check
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 7
    by mixed city/highway driving.) No additional vehicle service is required. If the Check Engine light remains on, have your vehicle serviced at the first available opportunity. Light is blinking: Engine misfire is occurring which could damage your catalytic converter. You should drive in a moderate
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 8
    at the first available opportunity. Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Fuel reset Illuminates when the ignition key is turned to the ON
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 9
    after releasing the parking brake indicates low brake fluid level. Anti-lock brake system (ABS) Momentarily illuminates when the ignition is turned on and the engine is off. If the light remains on, continues to flash or fails to illuminate, have the system serviced immediately. Turn signal
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 10
    Anti-theft system in the Controls and features chapter. THEFT Charging system Momentarily illuminates when the ignition is turned ON and the engine is off. The light also illuminates when the battery is not charging properly, requiring electrical system service. Check gage Illuminates when the key
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 11
    on when the transmission control switch is depressed or if the light flashes when you are driving, have your vehicle serviced. Speed control This light comes on when either the SET/ACCEL or RESUME controls are pressed. It turns off when the speed control OFF control is pressed, the brake is applied
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 12
    key is not in the ignition) and the driver's door is opened. GAUGES CHECK GAGE DOOR AJAR 4 H CHECK ENGINE 5 6 40 30 20 10 50 60 60 70 0 0 0 80 100 120 140 80 90 160 3 2 1 RPMx1000 C 40 000000 100 1 10 H L H SPEED CONT 4WD HIGH 4WD LOW 20 180 FUEL RESET F E ABS 0 ! BRAKE MPH
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 13
    remains within the normal area (the area between the "H" and "C"). If it enters the red section, the engine is overheating. Stop the vehicle, switch off the ignition and let the engine cool. Refer to Engine coolant in the Maintenance and care chapter. Never remove the coolant recovery cap while the
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 14
    zone may damage the engine. 4 3 2 1 0 5 6 RPMx1000 Battery voltage gauge This gauge shows the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range (as indicated), have the vehicle's electrical system checked as soon as possible
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 15
    oil pressure gauge This shows the engine oil pressure in the system. Sufficient pressure exists as long as the needle remains in the normal range (the area between the "H" and "L"). If the gauge indicates low pressure, switch off the engine immediately. Check the oil level. Add oil if needed (refer
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 16
    the highbeam headlamps on with a reduced output. To activate: • the engine must be running • the gearshift must not be in P (Park) • the headlamp control is in the OFF or Parking lamps position. The Daytime Running Light (DRL) system will not illuminate the tail lamps and parking lamps. Turn on your
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 17
    Controls and features High beams Push forward to activate. Flash to pass Pull back to activate and release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlight and parklamp operation. • Rotate up
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 18
    Controls and features CLIMATE CONTROL SYSTEM Manual heating and air conditioning system OFF A/C MAX A/C Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control OFF A/C
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 19
    while the system is working and even after you have stopped the vehicle. Under normal conditions, your vehicle's climate control system should be left in any position other than MAX A/C or OFF when the vehicle is parked. This allows the vehicle to "breathe" through the outside air inlet duct
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 20
    sent to the instrument panel registers. (Floor)-Allows for maximum • heating by distributing outside air through the floor ducts. However, the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode. (Floor and • defrost)-Distributes outside
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 21
    , the air conditioner will automatically dehumidify the air to prevent fogging. Operating tips • In humid weather, select before driving. This will drive with the climate control system in the OFF position. • Don't put objects under the front seat that will interfere with the airflow to the back
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 22
    conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open. This will force most of the hot, stale air out of the vehicle. Then operate your air conditioner as you would normally. • When placing objects on top of your instrument panel, be careful to
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 23
    not be equipped with rear console audio/climate controls. Turn the air distribution control to the desired airflow position. The instrument panel climate controls must be on in order for the rear climate control console controls to work. Turn the fan speed control to the desired position. - VOLUME
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 24
    Controls and features Select for air to flow through these vents: - VOLUME + BAND SEEK operate the rear window defroster. The defroster turns off automatically after 10 minutes or when the ignition is turned to the OFF position. To manually turn off the defroster before ten minutes have passed,
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 25
    and features 4WD CONTROL (IF EQUIPPED) This control operates the 4WD. Refer to Four-wheel drive (4WD) operation in the Driving chapter for more information. AUTO HIGH LOW AUDIO SYSTEM Refer to the "Audio Guide" in your owner portfolio. TURN SIGNAL CONTROL • Push down to activate the left turn
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 26
    Controls and features SPEED CONTROL To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). ON OFF Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. Do not shift the
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 27
    be greater than 48 km/h (30 mph). RSM SET ACC COAST If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or is faster than the set speed while driving on a downhill, you may want to shift to the next lower gear or apply the brakes to reduce your vehicle speed. If
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 28
    Controls and features To set a higher set speed • Press and hold SET ACC/SET ACCEL. Release the control when the desired vehicle speed is reached or • Press and release SET ACC/SET ACCEL. Each press will increase the set speed by 1.6 km/h (1 mph) or • Accelerate with your accelerator pedal, then
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 29
    pedal. When the desired vehicle speed is reached, press SET ACC/SET ACCEL. RSM SET ACC COAST To disengage speed control • Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. ON
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 30
    /RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). RSM SET ACC COAST Indicator light This light comes on when either the SET ACC/SET ACCEL or RES/RSM/RESUME controls are pressed. It turns off when the speed control OFF control
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 31
    the control while adjusting the wheel to the desired position, then release the control to lock the steering wheel in position. Never adjust the steering wheel when the vehicle is moving. HAZARD FLASHER For information on the hazard flasher control, refer to Hazard lights control in the Roadside
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 32
    for a longer wash cycle. Speed dependent wipers When the windshield wiper control is set on the intermittent settings, speed-sensitive front wipers automatically adjust as the vehicle's speed increases. Rear window wiper and washer For rear wiper operation, rotate the rear window wiper and washer
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 33
    ) Press the OPEN control to open the storage compartment. The door will open slightly and can be moved to full open. OPE N LAM P MO DE LAM P Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: 33
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 34
    door. • Place Velcro௢ hook onto side of aftermarket transmitter opposite of actuator control. • Place the transmitter into storage compartment, control down. • Place the provided height adaptors onto the back roof control to open. • To halt motion at any point during one-touch opening, press the
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 35
    The moon roof has a sliding shade that can be manually opened or closed when the glass panel is shut. To close MODE control on the overhead console. The vehicle heading is displayed as one of N, NE, E, SE, S, SW, W and NW. LAMP MODE LAMP 9 VAR Outside air temperature The temperature can be
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 36
    drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in or on the vehicle may also affect compass accuracy. Adjustments may need to be made to the zone and calibration of the compass. LAMP MODE OPEN
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 37
    . AUTOLAMP DELAY SYSTEM (IF EQUIPPED) The autolamp sets the headlamps to turn on and off automatically. The autolamp may be set to: • turn on the lamps automatically at night • turn off the lamps automatically during daylight • keep the lamps on for up to three minutes after the key is turned to
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 38
    from the normal state to the non-glare "active" state when bright lights (glare) reach the mirror. When the mirror detects bright light from front or behind, it will adjust automatically to minimize glare. The mirror will automatically return to the normal position 38 DELAY AUTOLAMP OFF MAX. DELAY
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 39
    the mirror is in the ON position). This helps to ensure a bright clear view in the mirror when backing up. POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. AUTO • Press the bottom portion of the rocker switch to
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 40
    and release quickly. The window will open fully. Depress again to stop window operation. AUTO Window lock The window lock feature allows only the driver to operate the power windows. POWER DOOR LOCKS Press U to unlock all doors and L to lock all doors. WINDOW LOCK U L Two step unlocking (if
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 41
    is equipped with the optional perimeter alarm system, this feature will work from all doors. CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 42
    Controls and features 3. Return to the center position to lock mirrors in place. CENTER CONSOLE Your vehicle may be equipped with a variety of console features. These include: • utility compartment with cassette POWER POINT The power point is an additional power source for electrical accessories. 42
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 43
    close the liftgate from outside the vehicle. It cannot be opened from inside the cargo area. • To open the liftgate window, unlock the liftgate (with the key or power door locks) and push the key lock cylinder. • To open the liftgate, unlock the liftgate and pull up on the handle under the license
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 44
    This will also prevent passengers and cargo from falling out. If you must drive with the liftgate door or window open, keep the vents open so outside air comes into the vehicle. CARGO COVER (IF EQUIPPED) Your vehicle may be equipped with a cargo area shade that covers the luggage compartment of your
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 45
    place any objects on the cargo area cover. They may obstruct your vision or strike occupants of the vehicle in the case of a sudden stop or collision. Rewinding the shade With extended use, the cargo shade may lose its spring tension. If this occurs, the shade must be manually rewound. This is a two
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 46
    end cap slots. 7. Insert the shade into the side mounting brackets and check to make sure that it operates properly. REMOTE ENTRY SYSTEM The remote entry system allows you to lock or unlock all vehicle doors without a key. The remote entry features only operate with the ignition in the OFF position
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 47
    all doors. Sounding a panic alarm Press this control to activate the alarm. To deactivate the alarm, press the control again or turn the ignition to ACC or ON. This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 48
    time and use • weather conditions • nearby radio towers • structures around the vehicle • other vehicles parked next to the vehicle To replace the battery: 1. Twist a thin coin between the two halves of the transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. 2. Place
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 49
    Reprogramming transmitters To reprogram all transmitters, place the key in the ignition and switch from OFF to ON eight times in a row (within 10 seconds). After doors lock/unlock, press any button on all exterior rear view mirrors) illuminate when the remote entry system is used to unlock the 49
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 50
    entry system to operate. The inside lights will not turn off if: • they have been turned on with the dimmer control or • any door is open. Battery saver will shut off the interior lamps 45 minutes after the last door is closed. Autolock Autolock is a feature that will automatically lock all doors
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 51
    Controls and features that the anti-theft system is not armed, the ignition is OFF and all vehicle doors and liftgate window are closed. 1. Enter the 5 digit entry code. 2. Press and release the 3/4 control while holding the 7/8 control. 3. Release the 7/8 control. The horn will chirp once if
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 52
    keyless entry keypad, you can: • lock or unlock the vehicle doors without using the key • arm and disarm the perimeter alarm system (if equipped) • activate/deactivate the autolock feature See also Remote entry system and Perimeter alarm system in this chapter for more information. Your vehicle has
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 53
    code does not replace the permanent code that the dealership gave you. You can use either code to unlock your vehicle. If a second personal code is entered, the module will erase the first personal code in favor of the new code. If you wish to erase your personal code, use the following instructions
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 54
    same time within five seconds of step two. The system will now only respond to the factory-set code. 1 2 3 4 5 6 7 8 9 0 Unlocking the doors with the keyless entry system To unlock the driver's door, enter either the factory-set code or personal code (each digit pressed within 5 seconds of the
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 55
    a triggered alarm, enter the five digit code. All doors must be fully closed for the alarm system to arm. Refer to the Perimeter alarm system section, if equipped, in this chapter for more details. PERIMETER ALARM SYSTEM Arming the system When armed, this system will help protect your vehicle from
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 56
    • Pressing 7/8 and 9/0 on the keyless entry pad at the same time to lock the doors (doors opened or closed). 1 2 3 4 5 6 7 8 9 0 If a door is open, the system is prearmed and is waiting for the door to close. The theft indicator on the instrument cluster will be lit continuously when the
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 57
    alarm is sounding. 1 2 3 4 5 6 7 8 9 0 SecuriLockி anti-theft system The SecuriLock௢ anti-theft system provides an advanced level of vehicle theft protection. Your vehicle's engine can only be started with the two special SecuriLock௢ electronically coded keys provided with your vehicle. Each
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 58
    the SecuriLock௢ anti-theft system. If the SecuriLock௢ key identification code matches the code stored in the SecuriLock௢ anti-theft system, the vehicle's engine is allowed to start. If the SecuriLock௢ key identification code does not match the code stored in the system or if a SecuriLock௢ key is not
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 59
    or flashes rapidly, have the system serviced by your dealership or a qualified technician. Programming spare SecuriLockி keys Spare SecuriLock௢ keys can be purchased from your dealership and programmed to your SecuriLock௢ anti-theft system (up to a total of 8 keys). Your dealership can program your
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 60
    readily accessible for the procedure. Please read and understand the entire procedure before you begin. 1. Insert the first previously programmed SecuriLock௢ key into the ignition switch and turn the ignition from OFF to RUN (maintain ignition in RUN for at least one second). 2. Turn ignition to OFF
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 61
    Controls and features If the programming procedure was successful, the new SecuriLock௢ key(s) will start the vehicle's engine. The theft indicator (located on the instrument cluster) will light for three seconds and then go out. If the programming procedure was not successful, the new SecuriLock௢
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 62
    position. Front seats Never adjust the driver's seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. 62
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 63
    power seat (if equipped) Never adjust the driver's seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. 63
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 64
    or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down. Using the power lumbar support The power lumbar control is located on the outboard side of the seat. Press one side of the control to adjust firmness. Press the other
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 65
    Seating and safety restraints REAR SEATS Head restraints Push or pull the head rests to the desired position. Folding rear seats (if equipped) If your vehicle is equipped with a built-in child seat, the seatback cannot be folded down unless the built-in child seat is fully stowed. 1. Press the
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 66
    seatback latches in the upright position. The seatback will click when it is locked into position. PUSH PUS H SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. To prevent the risk of injury, make sure
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 67
    injury in a collision. All occupants of the vehicle, including the driver, should always wear their safety belts. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 68
    the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle 68
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 69
    an impact of 8 km/h (5 mph) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers. Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 70
    . • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 71
    to the safety belt assembly by adding a safety belt extension assembly (part number 611C22). Safety belt extension assemblies can be obtained from your dealer belt across the torso. Safety belt warning light and indicator chime The seat belt warning light illuminates in the instrument cluster and a
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 72
    light remains The driver's safety belt is buckled before the ignition key off. is turned to ON...Safety belt maintenance Check the safety belt systems periodically to make sure they work properly and are not damaged. Check vehicles involved in a collision be replaced. However, if the collision was
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 73
    is noted. Failure to replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of a collision. Refer to Cleaning and maintaining the safety belts in the Maintenance and care section. AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) 4 5 6 50 60
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 74
    system is designed to: • work with the safety belt to protect the driver and right front passenger • reduce certain upper body injuries Failure to follow these instructions will affect the performance of the safety belts and increase the risk of personal injury. The right front passenger air
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 75
    bag cover on the steering wheel or in front seat areas that may come into contact with a deploying air bag. Failure to follow this instruction may increase the risk of personal injury in the event of a collision. Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 76
    restraints How does the air bag supplemental restraint system work? The SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 77
    (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to the
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 78
    be heard. The tone pattern will repeat periodically until the problem and light are repaired. If any of these things happen, even intermittently, have the SRS serviced at your dealership or by a qualified technician immediately. Unless serviced, the system may not function properly in the event of
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 79
    them in safety seats made especially for children. Check your local and state or provincial laws for from injury in a collision. Always follow the instructions and warnings that come with any infant or child Follow all the important safety restraint and air bag precautions that apply to adult
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 80
    shoulder belt. Moving the child closer to the center of the vehicle may help provide a good only (if equipped) OR • if the child is the proper size, restrain the child in a safety seat. Do not leave children labelled as conforming to all Federal motor vehicle safety standards. Belt-positioning
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 81
    safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer's instructions with the safety seat you put in unbuckling. • Place seat back in upright position. • Put the safety belt in the automatic locking mode. Refer to Automatic locking mode. Ford
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 82
    Attaching safety seats with tether straps. Carefully follow all of the manufacturer's instructions included with the safety seat you put in your vehicle. If you the child safety seat in a seat with a combination lap and shoulder belt. Air bag can kill or injure a child in a child seat. If you must
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 83
    . 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer's instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle for that seating position until you hear
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 84
    retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the 9. Before placing the child in the seat, forcibly tilt the seat forward and back to make sure the seat is securely held in place. 10. Try to
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 85
    and repeat steps two through nine. Check to make sure the child seat is back of the vehicle seat and attaches to an anchoring point. Other manufacturers offer the tether strap as an accessory instructions provided with the kit. Tether anchorage hardware kits (part number 613D74) including instructions
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 86
    include a built-in child seat. This child seat conforms to all Federal and local motor vehicle safety standard. Read the labels located on the child seat cushion and shoulder belt for be secured in an approved aftermarket seat. Refer to Children and infant or child safety seats in this chapter. 86
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 87
    in child seat Failure to follow all of the instructions on the use of this child restraint system can result in your child striking the vehicle's second row seatback must be fully locked before operating the child restraint system. Check the position of the seatback release lever. Never use the Built
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 88
    Seating and safety restraints 2. Pull both Velcro௡ straps to release the child seat cushion. 3. Lower the child seat cushion. 88
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 89
    Seating and safety restraints 4. Unfold the cushion protector flap onto adult seat cushion 5. If connected, disconnect the chest clip and buckles. 6. Place the child in the seat and position the left shoulder belt over the child's left shoulder first, then place the right shoulder belt over the
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 90
    Seating and safety restraints 7. Insert the left and right safety belt tongues into the left and right slots of the crotch buckle. Verify that the indicator window on each tongue is green to ensure proper safety belt connections. If both tongues do not latch in the buckle, do not use the child seat
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 91
    locking mode, the shoulder belts of the child seat will lock in response to hard braking, hard cornering or if your vehicle is involved in a collision with an impact of 8 km/h (5 m.p.h.) or more. Activating the automatic locking mode (ALR) on the built-in child safety seat 1. Fully extend the right
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 92
    Seating and safety restraints Deactivating the automatic locking mode (ALR) on the built-in child safety seat 1. Disconnect the chest clip and remove the left and right safety belt tongues from the
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 93
    of the head restraint is flush with the top of the adult seat back. 7. Press firmly on the top center of the built-in child safety seat head restraint to ensure it is was in use during a collision, Ford recommends replacing it. Built-in child restraints not in use during a collision should be
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 94
    speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. 94
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 95
    . Important safety precautions A computer system controls the engine's idle revolutions per minute (RPM). When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically, have the vehicle checked. Before starting the vehicle: 1. Make
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 96
    turning the key to 5 (START). 4 3 5 2 1 CHECK GAGE DOOR AJAR 4 H CHECK ENGINE 5 6 40 30 20 10 50 60 60 70 0 0 0 80 100 120 140 80 90 160 3 2 1 C 40 000000 100 1 10 H L H SPEED CONT 4WD 20 180
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 97
    Starting Make sure the corresponding lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced. • If the driver's safety belt is fastened, the light ( ) will not illuminate. STARTING THE ENGINE 1. Turn the key to 5 (START) without pressing the accelerator pedal and release
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 98
    smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes. These fumes are harmful and could kill you. Have the exhaust and body ventilation systems checked whenever: • the vehicle is raised for service 98
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 99
    the exhaust system changes • the vehicle has been damaged in a collision Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning (if equipped
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 100
    qualified service technician. Anti-lock brake system (ABS) On vehicles equipped with an anti-lock braking system (ABS), a noise from the hydraulic pump motor and pulsation in the pedal may be observed during ABS braking events. Pedal pulsation coupled with noise while braking under panic conditions
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 101
    Driving shudder while braking, felt mainly in the steering wheel, the vehicle most likely needs service. The ABS operates by detecting the onset of wheel lock up during brake applications and compensating for this tendency. The front wheels are prevented from locking even when the brakes are firmly
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 102
    when the ignition is turned ON) until the parking brake is released. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual transmission). The parking brake is not designed to stop a moving vehicle. However
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 103
    improve ride, handling and general vehicle performance during: • certain road conditions • steering maneuvers • braking • accelerations This system maintains the vehicle height at a constant level by automatically adding air or releasing air from the springs to offset changes in vehicle loads. 103
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 104
    panel. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Normal vehicle operation does not require any action by the driver. TRANSMISSION OPERATION Automatic transmission operation Brake-shift interlock This vehicle is
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 105
    . The transmission and tires may be damaged or the engine may overheat. Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn off the ignition whenever you leave your vehicle. Driving with a 4-speed automatic transmission (5.0L engines only) Understanding
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 106
    Hold the brake pedal down while in this gear. (Overdrive) The normal driving position for the best fuel economy. Transmission operates in transmission control switch on the end of the gearshift lever. The transmission control indicator light (TCIL) will illuminate on the instrument cluster. Drive
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 107
    engine braking is desired. If towing a trailer, refer to Driving while you tow in the Towing a trailer chapter. To return to (Overdrive) mode, press the transmission control switch. The TCIL will no longer be illuminated. Each time the vehicle is started, the transmission will automatically
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 108
    shift to a lower gear, and will shift to 1 (Low) after vehicle decelerates to the proper speed. Driving with a 5-speed automatic transmission (4.0L engines only) Understanding gearshift positions Hold the brake pedal down while you move the gearshift lever from position to position. If you do not
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 109
    ) With the gearshift in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this gear. (Overdrive) The normal driving position for the best fuel economy. Transmission operates in gears one through five. (Overdrive) can be deactivated by pressing the
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 110
    is useful whenever driving conditions (i.e., city traffic, hilly terrain, etc.) cause the transmission to excessively shift between (Overdrive) and (Drive). (Overdrive) Also deactivate when: • driving with a heavy load • towing a trailer up or down steep hills • additional engine braking is desired
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 111
    proper vehicle speed. CONTROL-TRAC AUTOMATIC FOUR-WHEEL DRIVE SYSTEM (IF EQUIPPED) The 4WD system uses all four wheels to power the vehicle. This increases traction, enabling you to drive your 4x4 over terrain and road conditions not normally traveled by two-wheel drive vehicles. Power is supplied
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 112
    conditions, such as deep snow and ice (where no dry or wet pavement remains uncovered), and shallow sand. AUTO HIGH LOW • The 4WD LOW mode supplies four-wheel drive equipped with 4WD or AWD, a spare tire of a different size than the road tires should never be used. Such a tire could result in damage
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 113
    to 4WD AUTO, the indicator light will turn off. Either shift can be done at a stop or while driving at any speed. AUTO HIGH LOW Shifting from 4WD AUTO or 4WD HIGH to 4WD LOW 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral) (automatic transmission) or
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 114
    brake. 3. Place the gearshift in N (Neutral) (automatic transmission) or depress the clutch (manual transmission). 4. Move the 4WD control to the 4WD AUTO or 4WD HIGH position. Driving wheel motion, make sure you grip the steering wheel from the outside. Do not grip the spokes. Drive cautiously
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 115
    , then press lightly on the accelerator. Do not rock the vehicle for more than a few minutes. The transmission and tires may be damaged or the engine can overheat. Do not spin the wheels at over 56 km/h (35 mph). The tires may fail and injure a passenger or bystander. Sand When driving over sand
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 116
    brake pedal. After driving through mud, clean off residue stuck to rotating driveshafts and tires. Excess mud stuck on tires and rotating driveshafts causes an imbalance that could damage drive components. If the transmission and transfer case are submerged in water, their fluids should be checked
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 117
    on the engine and the possibility of stalling. When descending a steep hill, avoid sudden braking. Rapid pumping of the brake pedal will Automatic transmissions may shift frequently while driving up steep grades. Eliminate frequent shifting (Overdrive) by shifting out of into D (Drive). Driving
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 118
    . In order to allow the anti-lock brake system (ABS) to operate properly, keep steady pressure on the brake pedal. Allow more stopping distance and drive slower than usual. Consider using one of the lower gears. ALL WHEEL DRIVE (AWD) SYSTEM (IF EQUIPPED) (5.0L ENGINES ONLY) Your vehicle is equipped
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 119
    the vehicle is stuck, shift the transmission in a steady motion between forward and reverse gears. Allow the transmission to engage, then press lightly on the accelerator. Do not rock the vehicle for more than a few minutes. The transmission and tires may be damaged or the engine can overheat. 119
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 120
    solid area of the trail. Do not reduce the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels. Mud and water If you must drive through high water, drive slowly. Traction or brake capability may be limited. When
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 121
    Driving If the transmission and transfer case are submerged in water, their fluids should be checked and changed, if necessary. Water intrusion into the transmission may damage the transmission. If the rear axle is submerged in water, the rear axle lubricant should be checked and changed, if
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 122
    ACCEL button (to resume speeds over 50 km/h (30 mph). Automatic transmissions may shift frequently while driving up steep grades. Eliminate frequent shifting (Overdrive) by shifting out of into D (Drive). Driving on snow and ice An AWD vehicle has advantages over 2WD vehicles in snow and ice but
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 123
    the manufacturer's specified size tires on a Traction-Lok rear axle could result in a permanent reduction in effectiveness. This loss of effectiveness does not affect normal driving and should not be noticeable to the driver. To avoid injury, never run the engine with one wheel off the ground, such
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 124
    weight of the base vehicle, passengers, optional equipment and cargo. The GVWR is specific to each vehicle and is listed on the Safety Compliance Label on the driver's door pillar. • GAWR (Gross Axle Weight Rating): Carrying capacity for each axle system. The GAWR is specific to each vehicle and is
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 125
    Driving loaded vehicle (including passengers and cargo) is permitted to tow. It is determined by subtracting Label. Do not use replacement tires with lower weight capacities than the originals because they may lower the vehicle's GVWR and GAWR limitations. Replacement tires with a higher weight limit
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 126
    enter your engine's air intake and severely damage your engine. If driving through deep or standing water is unavoidable, proceed very slowly. Never drive through water that is higher than the bottom of the hubs (truck)/wheel rims (car). Once through the water, always try the brakes. Wet brakes do
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 127
    Driving TRAILER TOWING Trailer towing with your vehicle may require the use of a trailer tow option package. Trailer towing puts additional loads on your vehicle's engine, transmission, axle, brakes, tires, and suspension. For your safety and to maximize vehicle performance, be sure to use the
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 128
    Driving this chapter. Remember to figure in the tongue load of your loaded vehicle when figuring the total weight. Trailer towing table (Automatic transmission) GCWR (Gross Combined Weight Rating)/Trailer Weights Trailer Weight Maximum Rear Maximum Range-kg frontal area of Engine axle GCWR-kg (lbs.)
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 129
    Driving Trailer towing table (4x4 and AWD with automatic transmission) Notes: For high altitude operation, reduce GCW by 2% per 300 meters (1 000 ft) elevation. For definition of terms and instructions clamp onto the vehicle bumper. Use a load carrying hitch. You must distribute the load in your trailer
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 130
    , follow the instructions that the rental agency gives to you. Trailer brakes Electric brakes and manual, automatic or surge-type brakes are safe if connect a trailer's hydraulic brake system directly to your vehicle's brake system. Your vehicle may not have enough braking power and your chances of
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 131
    for optimum fuel economy and transmission cooling. • Anticipate stops and brake gradually. Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to the Severe Duty Schedule in your "Service Guide" for more information. 131
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 132
    ) and increase idle speed. This aids engine cooling and air conditioner efficiency. • Vehicles with trailers should not be parked on a grade. If you must park on a grade, place wheel chocks under the trailer's wheels. Launching or retrieving a boat When backing down a ramp during boat launching or
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 133
    Driving • Do not allow waves to break higher than 15 cm (six inches) above the bottom edge of the rear bumper. Exceeding these limits not need to be checked unless a leak is suspected. Recreational towing (all wheels on the ground) Do not tow your vehicle with all wheels on the ground as vehicle
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 134
    Driving To adjust cross-bar position: 1. Slide the locking switches at each end can be completely removed in the UNLOCKED position by sliding the cross-bar rearward until it frees the guides. FUEL CONSUMPTION Fuel economy can be improved by avoiding: • lack of regular, scheduled maintenance •
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 135
    The "Fuel Reset" indicator light will illuminate in the instrument cluster. The shut-off switch is a device intended to stop the electric fuel pump when your vehicle has been involved in a substantial jolt. 1. Turn the ignition switch to the OFF position. 2. Check the fuel system for leaks. 3. If no
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 136
    the passenger's foot well, behind the kick panel. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. 15 15 136
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 137
    Roadside emergencies Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Color Tan Brown Red Light blue Yellow Light blue Natural Light green Pink Green Red Yellow Black Dark blue 137
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 138
    is located on the left hand side of the instrument panel facing the driver's side door. Pull the panel cover outward to access the fuses. To remove a fuse use the fuse puller tool provided on the fuse panel cover. 12 16 20 24 28 4 8 36 35 11 15 19 10 14 18 22
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 139
    (GEM), Shift Lock Actuator, Blend Door Actuator, Main Light Switch, RABS Resistor, A/C - Heater Assembly, Flasher Instrument Cluster, Main Light Switch, RABS Resistor Power Window Relay, Washer Pump Relay Stop Lamp Switch, Brake Pressure Switch Rear Anti-Lock Brake System (RABS) Module 7 8 7.5A
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 140
    14 Fuse Amp Rating 10A Description 4 Wheel Anti-Lock Brake System (4WABS) Module, 4WABS Main Relay Instrument Cluster Windshield Wiper Motor, Wiper Hi-Lo Relay, Wiper Run/Park Relay Cigar Lighter Drivers Unlock Relay, All unlock Relay, All Lock Relay PCM Power Diode RAP Module, Generic Electronic
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 141
    CD, Rear Integrated Control Panel, Memory Seat, Message Center 34 35 36 7.5A 10A 7.5A Power distribution box The power distribution box is located in the engine compartment near the battery. The power distribution box contains high-current fuses that protect your vehicle's main electrical systems
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 142
    MOTOR RELAY WASH PUMP RELAY FOG LAMP RELAY 9 5 7 11 3 1 4 9 WIPER PARK RELAY 12 8 The high-current fuses are coded as follows. Fuse/Relay Location 1 2 3 4 5 6 Fuse Amp Rating 50A** 40A** 50A** 20A** 50A** 20A** Description I/P Fuse Panel Blower Motor Relay 4 Wheel Anti-Lock Brake System
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 143
    -Lock System (4WABS) Module PCM Relay Fuel Pump Relay and RAP Module Horn Relay Parklamps Relay and Mainlight Switch Mainlight Switch and Multifunction Switch Heated Oxygen Sensor, EGR Vacuum Regulator, EVR Solenoid, Camshaft Position (CMP) Sensor, Canister Vent Solenoid, A4LD Automatic Transmission
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 144
    Fog Lamp Relay - Fog Lamp Relay Starter Relay - Starter Relay Blower Motor - Blower Motor Relay Relay 1 Resistor Fuse [7ca] 2 Diode Anti-Lock Brakes Indicator 3 Diode Electronic Engine Controls * Mini Fuses ** Maxi Fuses 1 5.0L Engines Only CHANGING THE TIRES If you get a flat tire while driving, do
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 145
    Left rear quarter panel behind interior trim Behind rear seats, under carpet Removing the spare tire 1. Insert the jack handle into the rear bumper opening. The handle will stop moving and forward resistance to turning will be felt when properly engaged. 2. Turn the handle counterclockwise until
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 146
    your vehicle. Refer to the instruction sheet for detailed tire change instructions. 1. Park on a level surface, activate hazard flashers and set the parking brake. 2. Place gearshift lever in P (Park). When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 147
    but do not remove them until the wheel is raised off the ground. 6. Turn OFF the air suspension switch (if equipped). Refer to Air suspension system in the Driving chapter. 7. Position the jack according to the following guides and turn the jack handle clockwise until the tire is a maximum of 25 mm
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 148
    or rear differential as a jacking point. 8. Remove the lug nuts with the lug wrench. 9. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts, cone side in, until the wheel is snug against the hub. Do not fully tighten the lug nuts until the
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 149
    Roadside emergencies 12. Stow the flat tire, jack and lug wrench. Make sure the jack is fastened so it does not rattle when you drive. 13. Turn ON the air suspension switch (if equipped). 14. Unblock the wheels. JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 150
    brake on both vehicles and stay clear of the engine cooling fan and other moving parts. 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. 5. Turn the heater fan on in both vehicles to protect any electrical surges. Turn all other accessories
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 151
    (-) booster battery terminal (2). 2. Remove the cable from the positive (+) terminal of the booster battery (3) and then the discharged battery (4). 3. After the disabled vehicle has been started, allow it to idle for a while so the engine can "relearn" its idle conditions. 4 1 + - - + 2 3 151
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 152
    professional towing service or, if you are a member, your roadside assistance center. If equipped with air suspension, the air suspension control must be turned to the OFF position. The Ford approved towing procedure is flatbed or wheel
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 153
    vehicle damage may occur. Do not tow with slingbelt equipment. Ford Motor Company has not developed or approved a slingbelt towing procedure. When towing manual is available from Ford Motor Company for all authorized tow truck operators. Have your tow truck driver refer to this manual for proper
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 154
    engine compartment for easy location. • We provide a "Service Guide" which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service. Check your "Warranty Guide" to find out which parts and services are covered. Use
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 155
    , open flames and other lit material away from the battery and all fuel related parts. If you disconnect the battery, the engine must "relearn" its idle conditions before your vehicle will drive properly, as explained in Battery in this chapter. Working with the engine off 1. Set the parking brake
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 156
    column on the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. Lift the hood until the lift cylinders hold it open. IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.0L SOHC engine 1 2 3 4 5 9 8 7 6 156
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 157
    5. Brake fluid reservoir 6. Battery 7. Power steering fluid reservoir 8. Air filter assembly 9. Engine coolant reservoir 5.0L engine 2 3 4 5 1 9 1. Engine coolant reservoir 2. Windshield washer fluid reservoir 3. Engine oil fill cap 4. Automatic transmission fluid dipstick 5. Brake fluid
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 158
    8. Engine oil dipstick 9. Air filter assembly ENGINE OIL Checking the engine oil Check the engine oil each time you fuel your vehicle. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 159
    Maintenance and care • 4.0L engines ADD 1 QT FULL • 5.0L engine MIN MAX 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the ADD and FULL marks (4.0L engines) or between the MIN and MAX marks (5.0L engines) the oil level is acceptable
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 160
    . Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the fluid level is not within the normal range, add
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 161
    . Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by your warranty. Changing the engine oil and filter Change your engine oil and filter according to the following
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 162
    knock may be experienced. It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application. BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed at least once each year: 1. Clean the
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 163
    in the Capacities and specifications chapter. Brake fluid is toxic. If you use a brake fluid that is not DOT 3, you will cause permanent damage to your brakes. Do not let the reservoir for the master cylinder run dry. This may cause the brakes to fail. WINDSHIELD WASHER FLUID Checking and adding
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 164
    in the container for the windshield washer fluid. ENGINE COOLANT Check the level of the coolant in the reservoir at least once a month. Be sure to read and understand Precautions when servicing your vehicle in this chapter. If the engine coolant has not been checked for a long period of time, the
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 165
    as possible. Check the coolant level in the coolant recovery reservoir the next few times you drive the vehicle. If necessary, add enough of a 50/50 mixture of coolant and water to bring the liquid level to the fill line on the reservoir. Never remove the coolant recovery cap while the engine is
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 166
    System Fluid E2FZ-19549-AA (in Canada, Motorcraft CXC-8-B) or an equivalent premium engine coolant that meets Ford specification ESE-M97B44-A. Ford Premium Engine engine cooling system. Recycled engine coolant Ford Motor Company recommends that Ford and Lincoln-Mercury dealers use recycled engine
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 167
    standards for recycling and disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle's cooling system can hold, refer to Refill capacities in the Capacities and specifications chapter. Have your dealer check the engine cooling system for leaks if you have to
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 168
    will be near the center of the NORMAL band). 2. While the engine idles, turn the steering wheel left and right several times. 3. Turn the engine off. 4. Check the fluid level in the reservoir. 5. If your vehicle is equipped with a 4.0L SOHC engine or a 5.0L engine, the fluid level should be between
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 169
    it reaches the correct operating range. Be sure to put the cap back on the reservoir. TRANSMISSION FLUID Checking and adding automatic transmission fluid Follow the scheduled service intervals outlined in the "Service Guide." Before adding any fluid, make sure the correct type is used. The type of
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 170
    trailer, the vehicle should be turned off for about 30 minutes to allow the fluid to cool before checking. 1. Park the vehicle on a level surface and engage the parking brake. 2. With the parking brake engaged and your foot on the brake pedal, start the engine and move the DON'T ADD DON'T ADD 170
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 171
    ) and leave the engine running. 4. Remove condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. If the fluid level is above the crosshatch (hot operating range) area after driving the vehicle for approximately 30 km (20 miles), excess transmission fluid
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 172
    plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter. DRIVELINE UNIVERSAL JOINT AND SLIP YOKE The universal
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 173
    If possible, however, try to only fill the battery cells with distilled water. If the battery needs water often, have the charging system checked. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 174
    maintained by power from the battery. When the battery is disconnected or a new battery is installed, the engine must relearn its idle conditions before your vehicle will drive properly. To begin this process: 1. Put the gearshift in P (Park), turn off all accessories and start the vehicle. 2. Let
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 175
    disposal. Call your local recycling center to find out more about recycling automotive batteries. WINDSHIELD WIPER BLADES Check the wiper blades at least twice the wiper blades When replacing wiper blade assemblies, always use a Motorcraft part or equivalent. To make replacing the wipers easy, 175
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 176
    LOCK. To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Tire Quality Grades apply to new pneumatic tires for use on passenger cars. They do not apply to deep tread, winter-type snow tires, space-saver or temporary use spare tires, tires
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 177
    as well on the government course as a tire grade 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 178
    . The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. The temperature grade for this
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 179
    in loss of vehicle control. Tire rotation Because your vehicle's tires perform different jobs, they often wear differently. To make sure your tires wear evenly and last longer, rotate them as indicated in the "Service Guide." If you notice that the tires wear unevenly, have them checked. 179
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 180
    Maintenance and care • Four tire rotation • Five tire rotation 180
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 181
    recommended on the decal. If you do not follow these precautions, your vehicle may not drive properly and safely. Make sure that all replacement tires are of the same size, type, load-carrying capacity and tread design (e.g., "All Terrain", etc.), as originally offered by Ford. Failure to follow
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 182
    install steel wheels of the same size and specifications as those originally installed. Follow these guidelines when using snow tires and chains: • Use only SAE Class S chains. • Install chains securely, verifying that the chains do not touch any wiring, brake lines or fuel lines. • Drive cautiously
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 183
    tire chains on dry roads. • The suspension insulation and bumpers will help prevent vehicle damage. Do not remove these components from your vehicle when using snow tires fuel tank can damage the fuel system or cause it to work improperly in a collision. The fuel system may be under pressure. If the
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 184
    Maintenance and care Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automotive fuels can be harmful or fatal if swallowed. If fuel is swallowed,
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 185
    fuels. However, even though your engine will perform adequately on other gasolines, the performance of the emission control devices and systems may be adversely affected. Repair of if your vehicle sometimes knocks lightly. However, if it knocks heavily under most driving conditions on fuel 87 185
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 186
    , see your dealer or a qualified service technician to prevent any engine damage. Fuel quality If you are experiencing starting, rough idle or hesitation problems try a different brand of fuel. If the condition persists, see your dealer or a qualified service technician. The American Automobile
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 187
    SYSTEM Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards. To make sure that the catalytic converter and other emission control components continue to work
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 188
    replacements or for service of components affecting emission control such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability. Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 189
    In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostic (OBD-II) system. If your "check engine/service engine soon" light is on, reference the applicable light description in the Warning Lights and Chimes section of your owners guide. Your vehicle may 189
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 190
    and care not pass the I/M test with the "check engine/service engine soon" light on. If the vehicle's powertrain system or its battery has just been serviced, the OBD-II system is reset to a "not ready for I/M test" condition. To ready the OBD-II system for I/M testing, a minimum of 30 minutes of
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 191
    used. To remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position, then open the hood. If you are replacing the driver side headlamp, unclip the electronic module on the right side of the battery and move it out of the way. 2. Locate the headlamp bulb through the hole in the
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 192
    the new bulb. 5. Remove the old bulb from its socket by gently pulling it straight back out of the socket. Do not turn the bulb while removing it. To install the into the socket. You may need to turn the bulb left or right to line up the grooves in the plastic base with the tabs in the socket. When
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 193
    into position. 4. Turn the headlamps on and make sure they work properly. If the headlamp was correctly aligned before you changed the Cargo lamp 1 211-2 Interior overhead lamp 1 912 (906) Front door courtesy 1 168 lamp Map lamps 2 168 (T10) Ashtray lamp 1 161 To replace all instrument panel lights
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 194
    's front structure is in its factory alignment condition. If the vehicle has been in an accident requiring the front end of the vehicle to be repaired, the horizontal indicator should be recalibrated by the servicing facility according to instructions in the vehicle's Workshop Manual. 194 D U
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 195
    dial lines up with the reference mark on the marker (as shown) when viewed directly from above. Vertical aim adjustment 1. Park the vehicle on a level surface. 2. With the hood open, the vertical adjusting screw clockwise or counterclockwise until the bubble is centered over the "0" mark. D U 195
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 196
    YOUR VEHICLE Refer to the "Customer Assistance Guide" for a list of Ford-approved cleaners, vehicle is particularly dirty, use a quality car wash detergent. Always use a clean sponge, any exterior accessories, such as antennas, before entering a car wash. After washing, apply the brakes several times
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 197
    • Take care when using a power washer to clean the engine. The high pressure fluid could penetrate the sealed parts and cause damage. • Do not spray with cold water to avoid cracking the engine block or other engine components. • Cover the highlighted areas to prevent water damage when cleaning the
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 198
    Maintenance and care • 5.0L • 4.0L SOHC 198
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 199
    and care • 4.0L EFI • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning the wheels Wash with the same detergent as the body of your vehicle. Do not use acid-based wheel cleaners, steel wool, fuel or strong detergents. Never use
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 200
    Maintenance and care Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. Use glass cleaner or tar remover if necessary. To avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners. Cleaning the wiper blades If the wiper
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 201
    , because these actions may weaken the belt webbing. Check the safety belt system periodically to make sure there are no nicks, wear parts of the seat. The child seat liner is removable and may be machine-washed and air dried. Underbody Flush the complete underside of vehicle frequently. Keep body
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 202
    Maintenance and care If the leather cannot be completely cleaned using a mild soap and water solution, the leather may cleaned using a commercially available cleaning product "Tanners Preserve Leather Cleaner" and a 3M "Type T' scrubbing pad by using the following steps; The type of scrubbing pad is
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 203
    Pads (UPC 04011-01276) are available through your local 3M distributor. Call 1-800-742-9649 for the nearest distributor in your area. PART NUMBER (Obtain Locally) (Obtain Locally) Woodtone trim Wipe stains with a soft cloth and a multi-purpose cleaning solution. Inside windows Use glass cleaner
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 204
    plug gap information. REFILL CAPACITIES Fluid Engine oil (including filter change) Brake fluid Ford Part Name Motorcraft 5W30 Super Premium Motor Oil Ford High Performance DOT 3 Brake Fluid Motorcraft MERCON ௡ ATF Application All Capacity 4.7L (5.0 quarts) Fill to the MAX line on reservoir All Fill
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 205
    and specifications Fluid Transmission fluid Ford Part Name Motorcraft MERCON௡V ATF Application 4R70W Automatic with 5.0L engine (AWD) 5R55E Automatic with 4.0L SOHC engine (4x2) 5R55E Automatic with 4.0L SOHC engine (4x4) AWD 4WD Engine coolant Ford Premium Cooling System Fluid Motorcraft 80W90
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 206
    and 3.73 or 4.10 rear axle ratios or 5.0L engines require synthetic rear axle lubricant. Rear axles containing synthetic lubricant are lubricated for life. These lubricants are not to be checked or changed unless a leak is suspected, service required or the axle assembly has been submerged in water
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 207
    to your "Service Guide" for axle fluid change intervals. LUBRICANT SPECIFICATIONS Ford part name or equivalent Ford Ultra-Clear Windshield Washer Concentrate Ford part number C9AZ-19550-AA OR -BA Ford specification Fluid Windshield washer fluid reservoir Body hinges, latches, door stricker plates
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 208
    Fluid Automatic transmission (4R70W) Automatic transmission (5R55E) Power steering reservoir Ford conventional and traction lok rear axles Front axle Transfer case Transfer case Front Output Slip Shaft 1 Ford part SAE 80W90 Premium Rear Axle Lube, part number XY-80W90-QL, Ford specification
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 209
    specification EST-M2C118-A to the rear axle whenever the axle has been serviced. ENGINE DATA Engine Cubic inches Horsepower Torque Required fuel grade Firing order Spark plug gap Ignition system Compression ratio VEHICLE DIMENSIONS Dimensions (1) Overall length (2) Overall width (3) Maximum height
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 210
    Capacities and specifications 4 1 3 5 2 210
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 211
    Capacities and specifications IDENTIFYING YOUR VEHICLE Safety compliance label MFD. BY FORD MOTOR door XXXXLB TIRE: OWNER GUIDE EXT AIR BAG XXXXXXXXXXXXXXXXX Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 212
    may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 213
    76 Air conditioning manual heating and air conditioning system ...18,21,23 Air suspension description ...103 All wheel drive (AWD) ...118 Ambulance packages ...3 Anti-lock brake system (ABS) ..101 Anti-theft system ...55 Autolamp system (see Headlamps) ...38 Automatic dimming mirror ...37,38 Battery
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 214
    52 locking and unlocking doors ...54 programming entry code ...53,54 Keys key in ignition chime ...12 Liftgate ...43 Lights, warning and indicator air bag ...8 anti-lock brakes (ABS) ...9 214 anti-theft ...10 brake ...9 charging system ...10 check engine ...6,7 cruise indicator ...11 door ajar ...10
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 215
    steering wheel ...31 Tires ...176,179 checking the pressure ...179 replacing ...181 rotating ...179 snow tires and chains ...182 treadwear ...177 Traction-lok rear axle ...123,172 Trailer towing ...127 tips ...132 Transfer case fluid checking ...172 Transmission ...169 automatic operation ...104
  • 1998 Mercury Mountaineer | Owner Guide 1st Printing - Page 216
    tank capacity Engine oil capacity (with filter change) Tire size and pressure Unleaded fuel only - 87 octane 79.5L (20.8 gallons) 4.7L (5.0 quarts). Use Motorcraft 5W30 Super Premium Motor Oil, Ford Specification WSS-M2C153-G See Safety Compliance Certification Label on inside of driver door. Pull
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
Before driving
Introduction
2
Instrumentation
4
Controls and features
16
Seating and safety restraints
62
Starting and driving
Starting
94
Driving
100
Roadside emergencies
135
Servicing
Maintenance and care
154
Capacities and specifications
204
Reporting safety defects
212
Index
213
All rights reserved. Reproduction by any means, electronic or mechanical
including photocopying, recording or by any information storage
and retrieval system or translation in whole or part is not permitted without
written authorization from Ford Motor Company.
Copyright
r
1997 Ford Motor Company
Elemental Chlorine Free
Contents
1