2010 Subaru Legacy Owner's Manual
2010 Subaru Legacy Manual
2010 Subaru Legacy manual content summary:
- 2010 Subaru Legacy | Owner's Manual - Page 1
This manual describes the following types of the Legacy series. 1) Legacy 2) Outback - 2010 Subaru Legacy | Owner's Manual - Page 2
- 2010 Subaru Legacy | Owner's Manual - Page 3
This chapter informs you what to do if you have a problem while driving, such as a flat tire or engine overheating. Chapter 10: Appearance care This chapter informs you how to keep your SUBARU looking good. Chapter 11: Maintenance and service This chapter informs you when you need to take your - 2010 Subaru Legacy | Owner's Manual - Page 4
brake system Anti knock index Automatic locking retractor Automatic transmission Automatic transmission fluid All-wheel drive Continuously variable transmission Daytime running light Electronic brake force distribution Emergency locking retractor Front-wheel drive Gross axle weight Gross axle weight - 2010 Subaru Legacy | Owner's Manual - Page 5
differential Malfunction indicator lamp Methylcyclopentadienyl manganese tricarbonyl Manual transmission On-board diagnostics SUBARU Intelligent Drive Supplemental restraint system Tire identification number Tire pressure monitoring system Vehicle dynamics control Front fog lights Turn signal Hazard - 2010 Subaru Legacy | Owner's Manual - Page 6
panel outlets and foot outlets Foot outlets Windshield defroster and foot outlets Windshield defroster Rear window defogger/Outside mirror defogger/Windshield wiper deicer Air recirculation Door unlock (transmitter) Trunk lid (Legacy) or rear gate (Outback) (transmitter) Outside air Engine - 2010 Subaru Legacy | Owner's Manual - Page 7
while still maintaining full vehicle control and the front passenger should move the seat as far back as possible and sit upright and well back in the seat. For instructions and precautions, carefully read the following sections. . For the seatbelt system, refer to "Seatbelts" F1-12. . For the SRS - 2010 Subaru Legacy | Owner's Manual - Page 8
the engine is running. If that is unavoidable, then use the ventilation fan to force fresh air into the vehicle. . Always keep the front ventilator inlet grille free from snow, leaves or other obstructions to ensure that the ventilation system always works properly. & Drinking and driving WARNING - 2010 Subaru Legacy | Owner's Manual - Page 9
seek treatment if you are addicted to those drugs. driving with others. & Car phone/cell phone and driving CAUTION Do not use a car phone/cell phone while driving; it may distract your attention from driving and can lead to an accident. If you use a car phone/cell phone, pull off the road and park - 2010 Subaru Legacy | Owner's Manual - Page 10
, damage or performance problems resulting from modification may not be covered under warranties. in the front passenger's seat. For further information, consult your veterinarian, local animal protection society or pet shop. & California proposition 65 warning WARNING Engine exhaust, some of its - 2010 Subaru Legacy | Owner's Manual - Page 11
Seat, seatbelt and SRS airbags Keys and doors Instruments and controls Climate control Audio Interior equipment Starting and operating Driving tips In case of emergency Appearance care Maintenance and service Specifications Consumer information and Reporting safety defects 1 2 3 4 5 6 7 8 9 10 11 - 2010 Subaru Legacy | Owner's Manual - Page 12
7) 8) 9) 10) 11) 12) Engine hood lock release (page 11-7) Headlight switch (page 3-27) Bulb replacement (page 11-50) Wiper switch (page 3-32) Moonroof (page 2-28) Roof rail (page 8-14) Door locks (page 2-5) Tire pressure (page 11-37) Flat tires (page 9-6) Fog light switch (page 3-30) Tie-down hooks - 2010 Subaru Legacy | Owner's Manual - Page 13
11 1) 2) 3) 4) 5) 6) 7) 8) 9) Rear window defogger button (page 3-34) Fuel filler lid and cap (page 7-3) Child safety locks (page 2-20) Towing hook (page 9-12) Tie-down hooks (page 9-13) Trunk lid (page 2-24) Rear gate (page 2-27) Bulb replacement (page 11-54) Rear wiper switch (page 3-34) - - 2010 Subaru Legacy | Owner's Manual - Page 14
12 & Interior ! Passenger compartment area 1) 2) 3) 4) 5) Lower anchorages for child restraint system (page 1-33) Seatbelt (page 1-12) Center console (page 6-6) Front seat (page 1-2) Rear seat (page 1-7) - 2010 Subaru Legacy | Owner's Manual - Page 15
13 1) 2) 3) 4) Top tether anchorages (page 1-35) Cargo area light (page 6-3) Rear center seatbelt (page 1-18) Cargo area cover (page 6-15) - CONTINUED - - 2010 Subaru Legacy | Owner's Manual - Page 16
14 1) 2) 3) 4) 5) 6) 7) Shift lever (MT) (page 7-16)/Select lever (AT and CVT) (page 7-19) Climate control (page 4-1) Audio (page 5-1) Navigation system (Refer to the Owner's Manual supplement for the navigation system) Multi function display (page 3-24) Glove box (page 6-6) Cup holder (page 6-8) - 2010 Subaru Legacy | Owner's Manual - Page 17
38) Illumination brightness control (page 3-30) Light control switch (page 3-27) Audio control buttons (page 5-30) Combination meter (page 3-5) Cruise control (page 7-38) Paddle shift (page 7-21) Wiper control lever (page 3-31) Horn (page 3-39) SRS airbag (page 1-38) Fuse box (page 11-48) Hood lock - 2010 Subaru Legacy | Owner's Manual - Page 18
(page 3-34) 5) Wiper intermittent time control switch (page 3-33) 6) Wiper control lever (page 3-32) 7) Light control switch (page 3-27) 8) Front fog light switch (page 3-30) 9) Headlight ON/OFF/AUTO (page 3-27) 10) Headlight flasher High/Low beam change (page 3-28) 11) Turn signal lever (page 3-29) - 2010 Subaru Legacy | Owner's Manual - Page 19
meter A/B selection and trip meter reset knob (page 3-6) Tachometer (page 3-7) Trip meter and odometer (page 3-6) Speedometer (page 3-6) Multi function display switching knob (page 3-24) Fuel gauge (page 3-7) Coolant temperature warning/indicator light (page 3-13) ECO gauge (page 3-8) - CONTINUED - - 2010 Subaru Legacy | Owner's Manual - Page 20
6) 7) 8) Trip meter A/B selection and trip meter reset knob (page 3-6) Tachometer (page 3-7) Trip meter and odometer (page 3-6) Speedometer (page 3-6) Multi function display switching knob (page 3-24) Fuel gauge (page 3-7) Coolant temperature warning/indicator light (page 3-13) ECO gauge (page 3-8) - 2010 Subaru Legacy | Owner's Manual - Page 21
warning light Engine oil level warning light AT OIL TEMP warning light (AT and CVT models) / ABS warning light Page 3-10 Mark / Name Brake system warning light Hill Holder indicator light Door open warning light 3-11 Door open indicator light Low fuel warning light 3-13 All-Wheel Drive warning light - 2010 Subaru Legacy | Owner's Manual - Page 22
2-18 2-16 2-8 2-11 2-7 3-34 Monitoring start delay time (after closure 0 second/30 seconds of doors) Impact sensor operation (only models with shock sensors (dealer option)) Passive arming Map light/Dome light/Cargo area light illumination Remote keyless entry system Key lock-in prevention Hazard - 2010 Subaru Legacy | Owner's Manual - Page 23
Automatic/Emergency Locking Retractor (A/ELR) ...Seatbelt warning light and chime ...Fastening the seatbelt ...Seatbelt maintenance ... 1-12 1-12 1-12 1-13 1-13 1-14 1-15 1-22 *SRS airbag (Supplemental Restraint System airbag)...Models with SRS airbags and lap/shoulder restraints for driver, front - 2010 Subaru Legacy | Owner's Manual - Page 24
a seatbelt, whichever is appropriate for the child's age, height and weight. Secure ALL types of child restraint devices (including forward facing child seats) in the REAR seats at all times. NEVER INSTALL A REARWARD FACING CHILD SEAT IN THE FRONT SEAT. DOING SO RISKS SERIOUS INJURY OR DEATH TO THE - 2010 Subaru Legacy | Owner's Manual - Page 25
front seating positions. For instructions and precautions concerning child restraint systems, refer to "Child restraint systems" F1-25. ! Reclining the seatback & Manual the reclining lever to return the seatback, hold the seatback lightly so that it may be raised back gradually. WARNING To - 2010 Subaru Legacy | Owner's Manual - Page 26
1-4 Seat, seatbelt and SRS airbags ! Seat height adjustment (driver's seat) & Power seat (if equipped) ! Driver's seat The height of the seat can be adjusted by moving the seat cushion adjustment lever up and down. When the lever is pushed down, - 2010 Subaru Legacy | Owner's Manual - Page 27
end of the control switch. Lumbar support control switch To increase lower back support, push the front side of the switch. To decrease lower back support, push the rear side of the switch. 1-5 2) ! Front restraint Release button Both the driver's seat and the front passenger's seat are equipped - 2010 Subaru Legacy | Owner's Manual - Page 28
Never drive the vehicle with the head restraints removed driver, should not operate a vehicle or sit in a vehicle's seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision. 1) 2) 3) A) B) HIGH - Rapid heating LOW - 2010 Subaru Legacy | Owner's Manual - Page 29
similar items. This may cause the seat heater to overheat. Rear seats NOTE Use of the seat heater for a long period of time while the engine is not running can cause battery discharge. WARNING WARNING Seatbelts provide maximum restraint when the occupant sits well back and upright in the seat. Do - 2010 Subaru Legacy | Owner's Manual - Page 30
SRS airbags & Reclining the seatback (Outback) cargo area cover when you recline the rear seat. . Move the front cover of the cargo area cover backward during a sudden stop, a sudden steering maneuver or a rapid acceleration. WARNING To prevent the passenger from sliding under the seatbelt in - 2010 Subaru Legacy | Owner's Manual - Page 31
The rear seatback may fold down quickly due to the internal spring. Hold the seatback while pulling the release lever to slow it down. ! Legacy ! Outback CAUTION Before folding down the rear seats, make sure that no one is sitting and nothing is placed on the rear seats. Otherwise, the seatback - 2010 Subaru Legacy | Owner's Manual - Page 32
WARNING . Never drive the vehicle with the head restraints removed because they are designed remove the head restraints, you must reinstall all head restraints to protect vehicle occupants. . All occupants, including the driver For Legacy, it is not possible to remove or install the head restraint - 2010 Subaru Legacy | Owner's Manual - Page 33
. To lower: Push the head restraint down while pressing the release button on the top of the seatback. To remove: While pressing the release button, pull out the head restraint. To install: Install the head restraint into the holes that are located on the top of the seatback until the head restraint - 2010 Subaru Legacy | Owner's Manual - Page 34
seatbelts BEFORE the vehicle starts to move. Otherwise, . Each seatbelt is designed to support only one person. Never use weight. Secure ALL types of child restraint devices (including forward facing child seats) in the REAR seats at all times. NEVER INSTALL A REARWARD FACING CHILD SEAT IN THE FRONT - 2010 Subaru Legacy | Owner's Manual - Page 35
in the front seating positions. For instructions and precautions concerning the child restraint system, refer to "Child restraint systems" F1- driver's seatbelt has an Emergency Locking Retractor (ELR). The emergency locking retractor allows normal body movement but the retractor locks automatically - 2010 Subaru Legacy | Owner's Manual - Page 36
Retractor (ELR) mode. For instructions on how to convert the retractor to the ALR mode and restore it to the ELR mode, refer to "Installing child restraint systems with A/ELR seatbelt" F1-28. the ignition switch is turned to the "ON" position, the seatbelt warning light(s) will flash for 6 seconds - 2010 Subaru Legacy | Owner's Manual - Page 37
. The front passenger's occupant detection system monitors whether or not there is a passenger on the front passenger's seat. Observe the following precautions. Failure to do so may prevent the device from functioning correctly or cause the device to fail. . Do not install any accessory such as - 2010 Subaru Legacy | Owner's Manual - Page 38
Front seatbelts 1. Adjust the seat position: Driver's seat: Adjust the seatback to the upright position. Move the seat as far from the steering wheel as practical while still maintaining full vehicle control. Front until you hear a click. WARNING Never place the lap belt as low as possible on your - 2010 Subaru Legacy | Owner's Manual - Page 39
front sudden braking or in a collision. ! Unfastening the seatbelt ! Rear seatbelts (except rear center seatbelt on Outback) adjusted to the position best suited for the driver/front passenger. Always adjust the anchor height so that door, make sure that the belts are retracted properly to - 2010 Subaru Legacy | Owner's Manual - Page 40
the belts are retracted properly to avoid catching the belt webbing in the door. ! Rear center seatbelt on Outback 4. To make the lap part tight, pull up on the shoulder belt. 5. Place the lap belt as low as possible on your hips, not on your waist. ! Unfastening the seatbelt 1) 2) 3) 4) Center - 2010 Subaru Legacy | Owner's Manual - Page 41
connector (tongue) plate. 3. After confirming that the webbing is not twisted, insert the connector (tongue) attached at the webbing end into the buckle on the right-hand side until a click is heard. If the belt stops before reaching the buckle, return the belt slightly and pull it out more slowly - 2010 Subaru Legacy | Owner's Manual - Page 42
hand side until it clicks. ! Unfastening the seatbelt 4. After fastening the seatbelt, make sure that the " " mark on the connector (tongue) and the " " mark on the buckle face outwards. 6. To make the lap part tight, pull up on the shoulder belt. And place the lap belt as low as possible on your - 2010 Subaru Legacy | Owner's Manual - Page 43
from the buckle. 2. Allow the retractor to roll up the belt. You should hold the webbing end and guide it back into the retractor while it is rolling up. Neatly store the tongue plate in the tongue plate can swing and hit against the trim during driving, causing damage to the trim. - CONTINUED - - 2010 Subaru Legacy | Owner's Manual - Page 44
is found. Front seatbelt pretensioners The driver's seat driver's and front passenger's seatbelt retractor assemblies must be replaced and only by an authorized SUBARU dealer . When replacing seatbelt retractor assemblies, use only genuine SUBARU parts. . If either front the front seatbelt is - 2010 Subaru Legacy | Owner's Manual - Page 45
parts. For required servicing of front seatbelt retractors equipped with seatbelt pretens i o n e r s , s e e y o u r n ea r e s t SUBARU dealer. . When discarding front seatbelt retractor assemblies or scrap- SRS airbag system warning light A diagnostic system continually monitors the readiness - 2010 Subaru Legacy | Owner's Manual - Page 46
1-24 Seat, seatbelt and SRS airbags system weight sensor . Front passenger's occupant detection control module . Front passenger's frontal airbag ON and OFF indicator . All related wiring while driving & System servicing WARNING . When discarding a seatbelt retractor assembly or scrapping the - 2010 Subaru Legacy | Owner's Manual - Page 47
of the suspension system or front end structure. . Installation of a tire of different size and construction from the tires specified on the vehicle placard attached to the door pillar or specified for individual vehicle models in this Owner's Manual. Child restraint systems tether anchorages - 2010 Subaru Legacy | Owner's Manual - Page 48
Front passenger's seat You should not install a child restraint system (including a booster seat) due to the hazard to children posed by the passenger's airbag. B: Rear seat, window-side seating positions Recommended positions for all types of child restraint systems. In these positions, Automatic - 2010 Subaru Legacy | Owner's Manual - Page 49
using the seatbelt. C: Rear seat, center seating position Installing a child restraint system is not recommended, although the A/ELR seatbelt and an and weight. According to accident statistics, children are safer when properly restrained in the rear seating positions than in the front seating - 2010 Subaru Legacy | Owner's Manual - Page 50
CAUTION When you install a child restraint system, follow the manufacturer's instructions supplied with it. After installing the child restraint system, check to Installing a rearward facing child restraint Choose a child restraint system that is appropriate for the child's age and size (weight and - 2010 Subaru Legacy | Owner's Manual - Page 51
out (ALR properly functioning). 8. To remove the child restraint system, press the release button on the seatbelt buckle and allow the belt to retract completely. The belt will return to the ELR mode. WARNING NEVER INSTALL A REARWARD FACING CHILD SEAT IN THE FRONT PASSENGER'S SEAT. DOING SO RISKS - 2010 Subaru Legacy | Owner's Manual - Page 52
Locking Retractor (ELR) to the Automatic Locking Retractor (ALR) function. Then, allow the belt to rewind into the retractor. As the belt is rewinding, clicks will be heard which indicate the retractor functions as ALR. 1. Place the child restraint system in the rear seating position. 2. Run - 2010 Subaru Legacy | Owner's Manual - Page 53
use, remove it and restore the ELR function of the retractor. That function is restored by allowing the seatbelt to retract fully. Outback 8. If the child restraint system requires a top tether, latch the hook onto the top tether anchor and tighten the top tether. For additional instructions, refer - 2010 Subaru Legacy | Owner's Manual - Page 54
1-32 Seat, seatbelt and SRS airbags CAUTION When you install a child restraint system, follow the manufacturer's instructions supplied with it. After installing the child restraint system, check to ensure that it is held securely in position. If it is not held tight and secure, the danger of your - 2010 Subaru Legacy | Owner's Manual - Page 55
three upper anchorages (tether anchorages) for accommodating such child restraint systems. CAUTION When you install a child restraint system, follow the manufacturer's instructions supplied with it. After installing the child restraint system, check to ensure that it is held securely in position - 2010 Subaru Legacy | Owner's Manual - Page 56
manufacturer's instructions supplied with it. After installing the child restraint system, check to ensure that it is held securely in position. If it is not held tight and secure, the danger of your child suffering personal injury in the event of an accident may be increased. Outback The tether - 2010 Subaru Legacy | Owner's Manual - Page 57
installation of the child restraint system. 1. While following the instructions supplied by the child restraint system remove the child restraint system, follow the reverse procedures of installation. If you have any question concerning this type of child restraint system, ask your SUBARU dealer - 2010 Subaru Legacy | Owner's Manual - Page 58
available. ! Tether anchorage location ! Legacy ! Outback ! To hook the top tether CAUTION Always remove the head restraint when mounting a child restraint system already installed on the rear edge of the roof. Open the cover flap to use each anchorage. Three tether anchorages are installed on - 2010 Subaru Legacy | Owner's Manual - Page 59
a sharp turn. 1. Remove the head restraint at the seating position where the child restraint system has been installed with the seatbelt or top tether hook of the child restraint system to the appropriate upper anchorage. 5. Tighten the top tether securely. ! Outback 3. Open the cover flaps to use - 2010 Subaru Legacy | Owner's Manual - Page 60
or death in a crash even when the vehicle has the SRS airbag. For instructions and precautions concerning the seatbelt system, & Models with SRS airbags and lap/shoulder restraints for driver, front passenger, and window-side rear passengers Your vehicle is equipped with a supplemental restraint - 2010 Subaru Legacy | Owner's Manual - Page 61
proper position such as one thrown forward during pre-accident braking. Even when properly positioned, there remains a possibility that an driver should always sit upright and well back in the seat as far from the steering wheel as practical while still maintaining full vehicle control and the front - 2010 Subaru Legacy | Owner's Manual - Page 62
restrained in the rear seating positions than in the front seating positions. For instructions and precautions concerning the child restraint system, refer to "Child restraint systems" F1-25. . NEVER INSTALL A REARWARD FACING CHILD SEAT IN THE FRONT SEAT. DOING SO RISKS SERIOUS INJURY OR DEATH TO - 2010 Subaru Legacy | Owner's Manual - Page 63
airbags 1-41 ! Components 1) 2) 3) 4) Front sub sensor (right-hand side) Front sub sensor (left-hand side) SRS airbag system warning light Frontal airbag module (driver's side) 5) 6) 7) Front passenger's frontal airbag ON and OFF indicator Frontal airbag module (front passenger's side) Airbag - 2010 Subaru Legacy | Owner's Manual - Page 64
hand side) Curtain airbag module (left-hand side) Curtain airbag module (right-hand side) Front passenger's occupant detection control module Side airbag sensor (left-hand side) Seatbelt pretensioner (left airbag sensor (right-hand side) 13) Front passenger's occupant detection system weight sensor - 2010 Subaru Legacy | Owner's Manual - Page 65
has warning labels on the driver's and front passenger's sun visors beginning with the phrase "EVEN WITH ADVANCED AIR BAGS" and a tag attached to the glove box lid beginning with the phrase "Even with Advanced Air Bags". Make sure that you carefully read the instructions on the warning labels and - 2010 Subaru Legacy | Owner's Manual - Page 66
in proper position such as one thrown toward the front of the vehicle during preaccident braking. WARNING Never hold a child on your lap driver should always sit upright and well back in the seat as far from the steering wheel as practical while still maintaining full vehicle control and the front - 2010 Subaru Legacy | Owner's Manual - Page 67
SUBARU dealer immediately if the SRS airbag system warning light illuminates. . Do not spill liquid on the front passenger's seat. If liquid is spilled, wipe it off immediately. . Do not remove or disassemble the front passenger's seat. . Do not install any accessory (such as an audio amplifier - 2010 Subaru Legacy | Owner's Manual - Page 68
SRS airbag system warning light illuminates. If your vehicle has sustained impact, this may affect the proper function of the SUBARU advanced frontal airbag system. Have your vehicle inspected at your SUBARU dealer. ! Passenger's frontal airbag ON and OFF indicators NOTE The front passenger's SRS - 2010 Subaru Legacy | Owner's Manual - Page 69
's seat, activating the front passenger's SRS frontal airbag even though that seat is occupied by a child. . Do not place any article on the seat other than the child occupant and a child restraint system. . Do not place more than one child on the seat. . Do not install any accessory such as a table - 2010 Subaru Legacy | Owner's Manual - Page 70
front passenger's seat are locked into place securely by moving the seat back and forth. (Models equipped with manual SUBARU dealer for an inspection. Even if the system has passed the dealer inspection between the front passenger's seat and side trim/ pillar, door or center console box. This may - 2010 Subaru Legacy | Owner's Manual - Page 71
suspension or floor panel can affect the operation of the SUBARU advanced air- bag system. If you have any questions, you may contact the following SUBARU distributors: Subaru of America, Inc. Customer Dealer Services Department P.O. Box 6000 - 2010 Subaru Legacy | Owner's Manual - Page 72
on the front passenger's seat monitored by the front passenger's occupant detection system weight sensor. For this reason, only the driver's SRS driver's module or both driver's and front passenger's modules) instructing the module(s) to inflate the SRS frontal airbag(s). The driver's and front - 2010 Subaru Legacy | Owner's Manual - Page 73
hard against an obstacle on the road such as a curb). A head-on collision against a thick concrete wall at a vehicle speed of 12 to 19 mph (20 to 30 km/h) or higher activates only the driver's SRS frontal airbag or both driver's and front passenger's SRS frontal airbags. The airbag(s) will also be - 2010 Subaru Legacy | Owner's Manual - Page 74
an object that can move or deform, such as a parked vehicle. ! Examples of the types of accidents in which deployment of the driver's/driver's and front passenger's SRS frontal airbag(s) is unlikely to occur. There are many types of collisions which might not necessarily require deployment of - 2010 Subaru Legacy | Owner's Manual - Page 75
the door panel and supplements the seatbelt by reducing the impact on the occupant's chest and waist. The SRS side airbag operates only for front seat driver's and/or front passenger's SRS frontal airbag(s) will deploy only once on the first impact. Example: In the case of a double collision, first - 2010 Subaru Legacy | Owner's Manual - Page 76
not seated in a proper upright position. . Since your vehicle is equipped with SRS curtain airbags, do not sit or lean unnecessarily close to the front or rear door on either side. Also, do not put your head, arms and hands out of the window. The SRS curtain airbag on each side of - 2010 Subaru Legacy | Owner's Manual - Page 77
to the SRS side airbag. Since your vehicle is also equipped with a front passenger's SRS frontal airbag, children aged 12 and under should be placed in the rear seat anyway WARNING . Do not attach accessories to the door trim or near either SRS side airbags and do not place objects - CONTINUED - 2010 Subaru Legacy | Owner's Manual - Page 78
free microphone or any other accessory to a front pillar, a center pillar, "ON" position. The driver's and front passenger's SRS side airbags driver's and front passenger's SRS frontal airbags in the steering wheel and instrument panel front seatback and do not attach labels or stickers to the front - 2010 Subaru Legacy | Owner's Manual - Page 79
the deployment, the SRS side airbag immediately starts to deflate. The time required from detection SRS curtain airbag deploy, a sudden, fairly loud inflation noise will be heard and some smoke will be released. any part of the SRS curtain airbag system (from the front pillar to the part of the roof - 2010 Subaru Legacy | Owner's Manual - Page 80
1-58 Seat, seatbelt and SRS airbags ! Example of the type of accident in which the SRS side airbag and SRS curtain airbag will most likely deploy (Legacy). A severe side impact near the front seat activates the SRS side airbag and SRS curtain airbag. - 2010 Subaru Legacy | Owner's Manual - Page 81
, seatbelt and SRS airbags 1-59 ! Examples of the types of accidents in which the SRS curtain airbag will most likely deploy (Outback). 1) 2) 3) A severe side impact near the front seat or the rear seat activates the SRS curtain airbag. The vehicle rolls onto its side or the roof. If the angle - 2010 Subaru Legacy | Owner's Manual - Page 82
SRS airbags 1) 2) 3) Hitting a curb, edge of pavement or hard surface Falling into or jumping over a deep hole Landing hard or vehicle falling ! Examples of the types of accidents in which it is possible that the SRS side airbag and the SRS curtain airbag will deploy (Outback). It is possible that - 2010 Subaru Legacy | Owner's Manual - Page 83
Seat, seatbelt and SRS airbags 1-61 ! Examples of the types of accidents in which the SRS side airbag and SRS curtain airbag are unlikely to deploy. 1) 2) 3) 4) 5) The vehicle is involved in an oblique side-on impact. The vehicle is involved in a side-on impact in an area outside the vicinity of - 2010 Subaru Legacy | Owner's Manual - Page 84
on the first impact, they will not be activated on the second. & SRS airbag system monitors 1) 2) A) B) First impact Second system (including front seatbelt pretensioners) while the vehicle is being driven. The SRS airbag system warning light "AIRBAG" will show normal system operation by lighting - 2010 Subaru Legacy | Owner's Manual - Page 85
) . Seatbelt buckle switch (front passenger's side) . Front passenger's occupant detection system weight sensor . Front passenger's occupant detection control module . Front passenger's frontal airbag ON and OFF indicator . All related wiring & SRS airbag system servicing WARNING . When discarding - 2010 Subaru Legacy | Owner's Manual - Page 86
of additional trim materials to the dashboard . Installation of custom seats . Replacement of seat fabric or leather . Installation of additional fabric or leather on the front seat . Attachment of a hands-free microphone or any other accessory to a front pillar, a center pillar, a rear pillar, the - 2010 Subaru Legacy | Owner's Manual - Page 87
. . Modification of the suspension system or front end structure. . Installation of a tire of different size and construction from the tires specified on the vehicle placard attached to the driver's door pillar or specified for individual vehicle models in this Owner's Manual. . Attachment of any - 2010 Subaru Legacy | Owner's Manual - Page 88
---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- - 2010 Subaru Legacy | Owner's Manual - Page 89
window operation by driver ...Power window operation by passengers...Initialization of power window ... 2-20 2-21 2-21 2-23 2-24 Remote keyless entry system ...Locking the doors ...Unlocking the doors ...Opening the trunk lid (Legacy)...Unlocking the rear gate (Outback)...Vehicle finder function - 2010 Subaru Legacy | Owner's Manual - Page 90
driving, it could turn the ignition switch from the "ON" position to the "Acc" or "LOCK" position, thereby stopping the engine replacement keys for models with the immobilizer system, refer to "Security ID plate" F2 your vehicle. . Ignition switch . Driver's door . Glove box . Trunk lid The valet key - 2010 Subaru Legacy | Owner's Manual - Page 91
starting the engine. Only keys registered with your vehicle's immobilizer system can be used to operate your vehicle. Even if an unregistered key fits into the ignition switch and can be turned to the "START" position, the engine will automatically the doors (all models) and rear gate (Outback). . - 2010 Subaru Legacy | Owner's Manual - Page 92
and doors (Canada-spec. models). NOTE Even if the security indicator light flashes irregularly or its fuse blows (the light does not flash if its fuse is blown), the immobilizer system will function normally. NOTE A vehicle that is equipped with the remote engine start system as a dealer option - 2010 Subaru Legacy | Owner's Manual - Page 93
the lock lever rearward. 2) Close the door. To lock the driver's door from the outside with the key, turn the key toward the rear. To unlock the door, turn the key toward the front. Lift the outside door handle to open an unlocked door. To lock the door from the outside without the key, rotate - 2010 Subaru Legacy | Owner's Manual - Page 94
red mark on the lock lever appears when the door is unlocked. Pull the inside door handle to open an unlocked door. Always make sure that all doors and the rear gate (Outback) are closed before starting to drive. *1: The map lights can be controlled by the battery drainage prevention function only - 2010 Subaru Legacy | Owner's Manual - Page 95
still in the ignition switch. ! Behavior with key lock-in prevention function operational With the driver's door open, the doors are automatically kept unlocked even if the front side of the power door locking switch is pressed. ! Behavior with key lock-in prevention function non-operational . If - 2010 Subaru Legacy | Owner's Manual - Page 96
has the following functions. . Locking and unlocking the doors (and rear gate (Outback)) without a key . Opening the trunk lid (Legacy) without key . Sounding a panic alarm . Arming and disarming the alarm system. For detailed information, refer to "Alarm system" F2-16. The operable distance of the - 2010 Subaru Legacy | Owner's Manual - Page 97
" " button to unlock the driver's door. An electronic chirp will sound twice and the turn signal lights will flash twice. To unlock all doors and the rear gate (Outback), briefly press the " " button a second time within 5 seconds. NOTE If the interval between the first and second presses of the - 2010 Subaru Legacy | Owner's Manual - Page 98
2-10 Keys and doors & Opening the trunk lid (Legacy) & Unlocking the rear gate (Outback) NOTE If the interval between presses is too short when you press the " " button three times, the system may not respond to the signals from the remote transmitter. & Sounding a panic alarm The trunk lid - 2010 Subaru Legacy | Owner's Manual - Page 99
driver's door within 10 seconds after performing step 4. 6. To indicate completion of the setting, the turn signal lights allow children to touch the battery and any removed parts; children could swallow them. . can be replaced by your authorized SUBARU dealer. If you replace the battery by yourself - 2010 Subaru Legacy | Owner's Manual - Page 100
doors & Replacing lost transmitters If you lose a transmitter or want to purchase additional transmitters (up to four can be programmed), you should reprogram all of your transmitters for security reasons. It is recommended that you have your dealer program all of your transmitters into your system - 2010 Subaru Legacy | Owner's Manual - Page 101
eight-digit number. Program the number into the system in accordance with the following procedure. 1. Firmly close the doors and the rear gate (Outback) or trunk lid (Legacy). 2. Open the driver's door, sit in the driver's seat, and close the door. 3. Perform the following steps within 45 seconds - 2010 Subaru Legacy | Owner's Manual - Page 102
the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3. 8. Before the electronic tone stops sounding, use the power door lock switch to reenter the transmitter code beginning with the leftmost digit. 5. Before the electronic tone - 2010 Subaru Legacy | Owner's Manual - Page 103
procedure beginning with part 4. When you have finished programming all of the necessary transmitter codes into the system, remove the key from the ignition switch. 11. Test every registered transmitter to confirm correct operation. ! Deleting old transmitter codes The control unit of the remote - 2010 Subaru Legacy | Owner's Manual - Page 104
the alarm system. Refer to "Disarming the system" F2-18. 2. Sit in the driver's seat and shut all doors (and the rear gate (Outback)). 3. Turn the ignition switch to the "ON" position. 4. Hold down the REAR (UNLOCK) side of the driver's power door locking switch, open the driver's door within the - 2010 Subaru Legacy | Owner's Manual - Page 105
arm the system using power door locking switch 1. Close all windows. 2. Remove the key from the ignition switch. 3. Open the doors and get out of the vehicle. 4. Make sure that the engine hood is locked. 5. Close the doors (and the rear gate (Outback)) but leave only the driver's door or the front - 2010 Subaru Legacy | Owner's Manual - Page 106
registered key. & Passive arming When passive arming mode has been programmed by the dealer, arming of the system is automatically accomplished without using the remote transmitter. Note that in this mode, DOORS MUST BE MANUALLY LOCKED. ! To enter the passive mode If you wish to program the passive - 2010 Subaru Legacy | Owner's Manual - Page 107
: twice (only models with shock sensors (dealer option)) . When a light impact was sensed: once (only models with shock sensors (dealer option)) 4. Before closing the doors, lock all doors with the inside door lock levers. 5. Close the doors. The system will automatically arm after 1 minute. In the - 2010 Subaru Legacy | Owner's Manual - Page 108
: - Vibration from construction site - Vibration in multistory car park - Vibration from trains . You can have the sensitivity of the shock sensors adjusted to your preference by your SUBARU dealer. Each rear door has a child safety lock that prevents the doors from being opened even if the inside - 2010 Subaru Legacy | Owner's Manual - Page 109
at the driver side door. To open: Press the switch down lightly and hold it. The window will open as long as the switch is held. This switch also has a one-touch auto down function that allows the window to be opened fully without holding the switch. Press the switch down until it clicks and - 2010 Subaru Legacy | Owner's Manual - Page 110
Keys and doors held. For some models, this switch also has a one-touch auto up function that allows the window to be closed fully without holding the switch. Pull the switch up until it clicks and release it, and the window will fully close. To stop the window halfway, press the switch down lightly - 2010 Subaru Legacy | Owner's Manual - Page 111
Each passenger window can be controlled by the power window switch located on the door. To open: Press the switch down and hold it until the window reaches the on the power window switch cluster, located on the driver's side door, is in the "LOCK" position, the passengers' windows cannot be operated - 2010 Subaru Legacy | Owner's Manual - Page 112
the switch for approximately 1 second after the window is closed completely. Trunk lid (Legacy) WARNING . To prevent dangerous exhaust gas from entering the vehicle, always keep the trunk lid closed while driving. . Help prevent children, adults or animals from locking themselves in the trunk. On - 2010 Subaru Legacy | Owner's Manual - Page 113
doors the trunk and play with the release handle. If the driver starts the vehicle without knowing that a child is inside the trunk opener switch, perform the following procedure. 1. Open the glove box. Refer to "Glove box" F6-6. 2. Press the trunk lid opener lock button. light even for a short time. - 2010 Subaru Legacy | Owner's Manual - Page 114
base is cracked, contact your SUBARU dealer. This places the latch in the locked position. 2. Use a flat-head screwdriver with a thin blade. Slide the flat-head screwdriver blade from the slit aperture of the lock assembly fully to the end until you hear a click. 3. Move the release handle, from - 2010 Subaru Legacy | Owner's Manual - Page 115
Keys and doors 2-27 Rear gate (Outback) WARNING . To prevent dangerous exhaust gas from entering the vehicle, always keep the rear gate closed while driving. . Do not attempt to shut the rear gate while holding the recessed grip. Also avoid closing the rear gate by pulling on the recessed grip - 2010 Subaru Legacy | Owner's Manual - Page 116
door locking/unlocking system or other causes, you can unlock it by manually operating the rear gate lock release lever. For the procedure, refer to "Rear gate (Outback the following instructions without exception vehicle, always remove the key falling snow or extremely cold conditions have caused - 2010 Subaru Legacy | Owner's Manual - Page 117
driving with the moonroof fully opened. . If the moonroof cannot be closed through the switch operation because of system failure, it can be closed manually raise the moonroof. Press the front side of the "UP/DOWN" opened together with the moonroof. For Outback, the moonroof will stop at a position - 2010 Subaru Legacy | Owner's Manual - Page 118
2-30 Keys and doors CAUTION Never attempt to test this function using fingers, hands or other parts of your body. & Sun shade The sun shade can be slid forward or backward by hand while the moonroof is closed. If the moonroof is opened, the sun shade also moves back. - 2010 Subaru Legacy | Owner's Manual - Page 119
spec. models)...ABS warning light...Brake system warning light...Hill Holder indicator light ...Low fuel warning light ...Door open warning light ...Door open indicator light ...Windshield washer fluid warning light ...All-Wheel Drive warning light (AT and CVT models) ...Vehicle Dynamics Control - 2010 Subaru Legacy | Owner's Manual - Page 120
/low beam change (dimmer)...Headlight flasher ...Daytime running light system ... 3-27 3-27 3-28 3-28 3-29 Wiper and washer...Windshield wiper and washer switches ...Rear window wiper and washer switch (Outback) ... 3-31 3-32 3-34 Turn signal lever ...Illumination brightness control ...Front fog - 2010 Subaru Legacy | Owner's Manual - Page 121
and START. removed in this position. The ignition switch will lock the steering wheel when you remove driving, it could turn the ignition switch from the "ON" posi. Keep the ignition switch in the "LOCK" position when the engine is not running. . Using electrical accessories CVT models). - CONTINUED - - 2010 Subaru Legacy | Owner's Manual - Page 122
and then try to start the engine again. . The key grip is touching another key or a metallic key holder. & Ignition switch light For easy access to the ignition switch in the dark, the ignition switch light illuminates when driver's door is opened or when the driver's door is unlocked using the - 2010 Subaru Legacy | Owner's Manual - Page 123
to start the engine. This show MIN position. 4. Dials and indicators in meters and gauges light up. 5. Regular illumination (for driving) begins. & Canceling the function for meter/gauge needle movement upon turning on the ignition switch The hazard warning flasher is used to warn other drivers - 2010 Subaru Legacy | Owner's Manual - Page 124
shows the vehicle speed. seconds of illumination of the odometer/ trip meter, the odometer/trip meter will turn off. Also, if you open and close the driver's door in the "LOCK" or "Acc" position, the odometer/trip meter will light up. It is NOTE . Your vehicle's initial movement setting of the - 2010 Subaru Legacy | Owner's Manual - Page 125
the driver's door within 10 CVT models) or the shift lever is in the neutral position (for MT models), the engine is controlled so that the engine speed may not become too high even if the accelerator Low fuel warning light The fuel gauge shows the approximate amount of fuel remaining in the tank - 2010 Subaru Legacy | Owner's Manual - Page 126
the driver's door, the fuel gauge needle will drop to the "E" position and the dial and needle will turn off. gauge. This indicates that the fuel filler door (lid) is located on the right side of the vehicle. ! Low fuel warning light The low fuel warning light illuminates when the fuel tank is - 2010 Subaru Legacy | Owner's Manual - Page 127
front seat passenger fastens the seatbelt.) : SRS airbag system warning light : CHECK ENGINE warning light/Malfunction indicator lamp : Coolant temperature high warning light : Charge warning light : Oil pressure warning light : Engine low oil level warning light : Windshield washer fluid warning - 2010 Subaru Legacy | Owner's Manual - Page 128
to illuminate, it indicates a burned-out bulb or a malfunction of the corresponding system. Consult your authorized SUBARU dealer for repair. & Seatbelt warning light and chime Your vehicle is equipped with a seatbelt warning device at the driver's and front passenger's seat, as required by current - 2010 Subaru Legacy | Owner's Manual - Page 129
equipped with manual seats only) If still the seatbelt warning device for front passenger's seat does not function correctly after taking relevant corrective actions described above, immediately contact your SUBARU dealer for an inspection. & SRS airbag system warning light When the ignition - 2010 Subaru Legacy | Owner's Manual - Page 130
the light illuminates steadily while driving or does not turn off after the engine starts, an emission control system malfunction has been detected. You should have your vehicle checked by an authorized SUBARU dealer immediately. The front passenger's frontal airbag ON and OFF indicators show you - 2010 Subaru Legacy | Owner's Manual - Page 131
by your nearest SUBARU dealer. Refer to "Engine overheating" F9-12. - Blinking in RED and BLUE alternately: The electrical system may be malfunctioning. Contact your SUBARU dealer for an inspection. This coolant temperature low indicator light/coolant temperature high warning light has the following - 2010 Subaru Legacy | Owner's Manual - Page 132
is running, it may indicate that the engine oil pressure is low and the lubricating system is not working properly. If the light illuminates while driving or does not turn off after the engine starts, stop the engine at the first safe opportunity and check the engine oil level. If the oil level is - 2010 Subaru Legacy | Owner's Manual - Page 133
the engine idle until the warning light turns off. ! Transmission control system warning If the "AT OIL TEMP" warning light flashes after the engine has started, it may indicate that the transmission control system is not working properly. Contact your nearest SUBARU dealer for service immediately - 2010 Subaru Legacy | Owner's Manual - Page 134
blinking for approximately one minute, you should have your Tire Pressure Monitoring System checked at a SUBARU dealer as soon as possible. If this light illuminates while driving, never brake suddenly and keep driving straight ahead while gradually reducing speed. Then slowly pull off the road - 2010 Subaru Legacy | Owner's Manual - Page 135
system repaired at the first available opportunity by your SUBARU dealer. The ABS warning light illuminates to- NOTE If the warning light behavior is as described in the following conditions, the ABS system may be considered normal. . The warning light illuminates right after the engine is started - 2010 Subaru Legacy | Owner's Manual - Page 136
and with the parking brake fully released. If the brake system warning light should illuminate while driving (with the parking brake fully released and with the ignition switch positioned in "ON"), it could be an indication of leaking of brake fluid or worn brake pads. If this occurs, immediately - 2010 Subaru Legacy | Owner's Manual - Page 137
the Hill Holder function, the electronic parking brake system may be malfunctioning. Immediately stop the vehicle in a safe location and contact your SUBARU dealer. CAUTION Promptly put fuel in the tank whenever the low fuel warning light illuminates. Engine misfires as a result of an empty - 2010 Subaru Legacy | Owner's Manual - Page 138
you start to drive. & Windshield washer fluid warning light This light illuminates when the fluid level in the windshield washer fluid tank decreases to the lower limit (approximately 0.6 US qt, 0.6 liter, 0.5 Imp qt). & All-Wheel Drive warning light (AT and CVT models) WARNING sively low in - 2010 Subaru Legacy | Owner's Manual - Page 139
, the ordinary functions of the brake system are still available. You will be safe while driving with this condition, but drive carefully and have your vehicle checked at a SUBARU dealer as soon as possible. checked at a SUBARU dealer immediately. . The warning light does not illuminate when the - 2010 Subaru Legacy | Owner's Manual - Page 140
, it may indicate that immobilizer system may be "Automatic transmission/Continuously variable transmission" F7-18. ! MT models The shift-up indicator light illuminates and informs the driver about the upshift timing for fuel-efficient driving. The gear position indicator light and the shift-up - 2010 Subaru Legacy | Owner's Manual - Page 141
dealer. & Turn signal indicator lights These lights show the operation of the turn signal or lane change signal. If the indicator lights do not blink or blink rapidly, the turn signal bulb may be burned out. Replace the bulb as soon as possible. Refer to "Replacing bulbs" F11-50. & Front fog light - 2010 Subaru Legacy | Owner's Manual - Page 142
up. Multi function display Your SUBARU dealer can change the settings of activating/deactivating the automatic adjustment of the clock by the GPS (Global Positioning System) (for models with the genuine SUBARU navigation system). Contact your SUBARU dealer for details. With the ignition switch - 2010 Subaru Legacy | Owner's Manual - Page 143
outside temperature. The road surface freeze warning indication should be treated only as a guide. Be sure to check the condition of the road surface before driving. & Average fuel consumption 1) 2) U.S.-spec. models Except U.S.-spec. models 1) 2) U.S.-spec. models Except U.S.-spec. models The - 2010 Subaru Legacy | Owner's Manual - Page 144
a guide. . When either trip meter indication is reset, the average fuel consumption fuel remaining in the tank and the average rate of fuel consumption. When the low fuel warning light illuminates, the driving range indication flashes for 5 seconds. (The display first switches to the driving - 2010 Subaru Legacy | Owner's Manual - Page 145
and the key is removed from the ignition switch, the chirp sound informs the driver that the lights are illuminated. To turn on the headlights, turn the knob on the end of the turn signal lever. first position Instrument panel illumination, tail lights, front side marker lights and license plate - 2010 Subaru Legacy | Owner's Manual - Page 146
Instruments and controls : Auto on/off headlights When the ignition switch is in the "ON" position, the headlights, instrument panel illumination, front side marker lights, tail lights and license plate lights are automatically on or off depending on the level of the ambient light. CAUTION If any - 2010 Subaru Legacy | Owner's Manual - Page 147
by the daytime running light system. The light switch must always be turned to the " " position when it is dark outside. The high beam headlights will automatically illuminate at reduced brightness when the engine has started, under the following conditions. . The parking brake is fully released - 2010 Subaru Legacy | Owner's Manual - Page 148
maximum and the automatic dimming function does not work at all. . The brightness setting is not canceled even when the ignition switch is turned to the "LOCK" position. Front fog light switch (if equipped) The illumination brightness of the clock display, audio, air conditioner, multi function - 2010 Subaru Legacy | Owner's Manual - Page 149
meter will illuminate when the front fog lights are on. CAUTION . Do not operate the washer continuously for more than 10 seconds, or when the washer fluid tank is empty. This may cause overheating of the washer motor. Check the washer fluid level frequently, such as at fuel stops. . Do not operate - 2010 Subaru Legacy | Owner's Manual - Page 150
fluid" F11-42. Also, when driving the vehicle when there are freezing temperatures, use non-freezing type wiper blades. . Do not clean the wiper blades with gasoline or a solvent, such as paint thinner or benzine. This will cause deterioration of the wiper blades. NOTE . The front instructions Low - 2010 Subaru Legacy | Owner's Manual - Page 151
lever. The wipers operate while you pull the lever. The windshield washer fluid warning light illuminates when the washer fluid level in the tank has dropped to the lower limit. If the warning light illuminates, refill the tank with fluid. For the tank refilling method, refer to "Windshield washer - 2010 Subaru Legacy | Owner's Manual - Page 152
Outback) : Washer (accompanied by wiper operation) ON: Continuous INT: Intermittent OFF: Off : Washer (accompanied by wiper operation) lever to the "R" position (AT and CVT turn the knob on the end of the wiper control lever upward to the " " position. The washer fluid sprays until you release the - 2010 Subaru Legacy | Owner's Manual - Page 153
of the defogger and deicer system is canceled and the system stops operating. Automatic climate control system Manual climate control system To activate the defogger and deicer system, press the control switch that is located on the climate control panel. The rear window defogger, outside - 2010 Subaru Legacy | Owner's Manual - Page 154
windshield wiper deicer automatically stops operating, though the rear window defogger and outside mirror defogger maintain continuous operation in this condition. Mirrors Always check that the inside and outside mirrors are properly adjusted before you start driving. & Auto-dimming mirror/compass - 2010 Subaru Legacy | Owner's Manual - Page 155
bright if the transmission is shifted into reverse accessories (rear window defogger, heater/air conditioning system, spotlight, etc.) and ensure all doors are shut. 2. Drive map attached to the end of this manual to verify that the a photosensor attached on both the front and back sides. If the - 2010 Subaru Legacy | Owner's Manual - Page 156
Do not adjust the steering wheel tilt/ telescopic position while driving. This may cause loss of vehicle control and result in prevent unintentional operation. The mirrors can also be adjusted manually. 1. Adjust the seat position. Refer to "Front seats" F1-2. 2. Pull the tilt/telescopic lock lever - 2010 Subaru Legacy | Owner's Manual - Page 157
Instruments and controls 3-39 and forward and backward. Horn To sound the horn, push the horn pad. - 2010 Subaru Legacy | Owner's Manual - Page 158
---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- - 2010 Subaru Legacy | Owner's Manual - Page 159
and low temperature weather condition...Air conditioner compressor shut-off when engine is heavily loaded...Refrigerant for your climate control system ... 4-14 4-14 4-14 4-14 4-14 4-14 4 Control panel ...4-9 Temperature sensors...4-13 Air filtration system ...Replacing an air filter... 4-15 - 2010 Subaru Legacy | Owner's Manual - Page 160
4-2 Climate control Ventilator & Air flow selection - 2010 Subaru Legacy | Owner's Manual - Page 161
Close 1) 2) Open Close Move the tab up and down or right and left to adjust the flow direction. To open the ventilator, turn the center grille open/close wheel to the " " position. To close it, turn the wheel to the " " position. Move the tab up and down or right and left - 2010 Subaru Legacy | Owner's Manual - Page 162
4-4 Climate control 1) 2) 3) 4) 5) 6) Fan speed control dial Temperature control dial Air flow control buttons Air conditioner button Air inlet selection button Rear window defogger button (Refer to "Defogger and deicer" F3-34.) Manual climate control system (if equipped) & Control panel - 2010 Subaru Legacy | Owner's Manual - Page 163
air flow from the air outlets over a range from the blue side (cool) to red side (warm). ! Air flow control buttons : Air flows through the instrument panel outlets and the windshield defroster outlets. NOTE When the " " button or " " button is pressed the air conditioner compressor automatically - 2010 Subaru Legacy | Owner's Manual - Page 164
and front door windows: 1. Set the air inlet selection button to the OFF position. 2. Press the " " button. The air conditioner operates only when the engine is running. Press the air conditioner button while the fan is in operation to turn on the air conditioner. The indicator light will - 2010 Subaru Legacy | Owner's Manual - Page 165
When driving on a dusty road, set the air inlet control button to the ON position. WARNING Continued operation in the ON position may fog up the blue side. 5. Set the fan speed control dial at the desired speed. ! Defrosting or defogging To direct warm air to the windshield and front door windows: - 2010 Subaru Legacy | Owner's Manual - Page 166
to "outside air" mode. Automatic climate control system (if equipped) NOTE . Operate the automatic climate control system when the engine is running. . The blower fan rotates at a low speed when the engine coolant temperature is low. For efficient defogging or dehumidifying in cold weather, press - 2010 Subaru Legacy | Owner's Manual - Page 167
Climate control 4-9 & Control panel 1) 2) 3) 4) 5) Temperature control button (driver's side) Dual mode button Air flow mode selection button Fan speed control button Temperature control button (front passenger's side) 6) AUTO button 7) OFF button 8) Air inlet selection button 9) Defroster - 2010 Subaru Legacy | Owner's Manual - Page 168
during FULL AUTO mode operation, the indicator light "FULL" on the control panel will turn off and the indicator light "AUTO" will remain illuminated. You can then manually control the system as desired using the button The automatic climate control system turns off (the air conditioner compressor - 2010 Subaru Legacy | Owner's Manual - Page 169
, the indicator light on the "DUAL" button turns off and the temperature setting for the front passenger's side becomes the same as the setting for the driver's side. ! - Defroster button After eliminating the fogging from the windshield, return the climate control system to the FULL AUTO mode by - 2010 Subaru Legacy | Owner's Manual - Page 170
to quickly defog the windshield and the air inlet selection is automatically set to the "outside air" mode. ! Air inlet selection button If the windshield starts to fog when the climate control system is operated in the AUTO mode, press the air conditioner button "A/C" to defog and dehumidify. When - 2010 Subaru Legacy | Owner's Manual - Page 171
temperature sensor: on the side of the driver-side part of the center panel - Outside temperature sensor: behind front grille. NOTE When driving on a dusty road or behind a vehicle that emits unpleasant exhaust gases, set the air inlet selection button to the ON position (recirculation). From time - 2010 Subaru Legacy | Owner's Manual - Page 172
refrigerant circuit Operate the air conditioner compressor at a low engine speed (at idle or low driving speeds) a few minutes each month during the off-season to circulate its oil. & Checking air conditioning system before summer season Always keep the front ventilator inlet grille free of snow - 2010 Subaru Legacy | Owner's Manual - Page 173
km) whichever comes first NOTE The filter can influence the air conditioning, heating and defroster performance if not properly maintained. & Replacing an air filter 1. Remove the glove box. (1) Open the glove box. (3) Pull out the glove box. CAUTION Contact your SUBARU dealer if the following - 2010 Subaru Legacy | Owner's Manual - Page 174
CAUTION The arrow mark on the filter must point UP. 3. Remove the air filter. 1) Service label (2) Attach the service label to the driver's side door pillar. 6. Reinstall the glove box, and connect the damper shaft. 7. Close the glove box. 8. LABEL installation (1) Fill out the information on - 2010 Subaru Legacy | Owner's Manual - Page 175
Climate control 4-17 driver's side of the instrument panel as shown in the illustration. - 2010 Subaru Legacy | Owner's Manual - Page 176
---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- - 2010 Subaru Legacy | Owner's Manual - Page 177
radio reception (if equipped)...Installation of accessories...Audio set ...Type A audio set (if equipped) ...Type B audio set (if equipped) ... system (if equipped) ...Tips for the Hands-free system ...Certification for the Hands-free system...Safety precautions ...Using the Hands-free system - 2010 Subaru Legacy | Owner's Manual - Page 178
. XMTM provides digital quality audio and text information, including song title and artist name. A service fee is required to receive the XM TM service. For more information, contact then relayed throughout the USA by a network of ground repeater stations. The satellite radio signals are transmitted - 2010 Subaru Legacy | Owner's Manual - Page 179
Audio 5-3 You may experience problems in receiving XMTM satellite radio signals in the following situations. . If you are driving northward in a coastal area You will notice that the XMTM satellite radio antenna is fixed to the upper right hand corner of your windshield. The - 2010 Subaru Legacy | Owner's Manual - Page 180
Installation of accessories Always consult your SUBARU dealer before installing a citizen band radio or other transmitting device in your vehicle. Such devices may cause the electronic control system to malfunction if they are incorrectly installed or if they are not suited for the vehicle. Audio - 2010 Subaru Legacy | Owner's Manual - Page 181
set (if equipped) The audio set will operate only when the ignition switch is in the "Acc" or "ON" position. . Power and sound controls: refer to page 5-7 . Radio operation: refer - 2010 Subaru Legacy | Owner's Manual - Page 182
set (if equipped) The audio set will operate only when the ignition switch is in the "Acc" or "ON" position. . Power and sound controls: refer to page 5-7 . Radio operation: refer - 2010 Subaru Legacy | Owner's Manual - Page 183
5-7 Power and sound controls & Power switch and volume control & Sound control ! Tone and balance control ! Other sound setting controls (type A audio) The dial is used for both power (ON/OFF) and volume control. The radio is turned ON and OFF by pressing the dial, and the - 2010 Subaru Legacy | Owner's Manual - Page 184
according to the vehicle speed. As the vehicle speed increases, the audio volume automatically increases to match the vehicle speed, in order to create a pleasant listening environment even as the driving noise increases. The amount of this automatic volume change can be set in the range from OFF to - 2010 Subaru Legacy | Owner's Manual - Page 185
Treble control Fader Balance Other settings SPEED VOLUME CS Auto (type A audio) POSITION *Only when an AUX audio product is connected. Range of levels (displayed) For less bass sound For less midrange sound For less treble sound Front attenuated Right channel attenuated From 2 to 1, 1 to OFF From FL - 2010 Subaru Legacy | Owner's Manual - Page 186
selection & Tuning ! Manual tuning & FM selection Press the "AM" button when the radio is on to select AM reception. Press the "FM" button when the radio is on to select FM1, FM2 or FM3 reception. Each brief press of the "FM" button changes the radio in the following sequence starting from the - 2010 Subaru Legacy | Owner's Manual - Page 187
" side of the "SEEK" button briefly, the radio will automatically search for a receivable station and stop at the first one it finds. This function may not be available, however, when radio signals are weak. In such a situation, perform manual tuning to select the desired station. If you press the - 2010 Subaru Legacy | Owner's Manual - Page 188
5-12 Audio ! PTY (Program type) group selection ! Seek in PTY (Program type) group & RDS returns to the normal mode after approximately 10 seconds. If the PS (Program Service Name) and/or RT (Radio Text) are available, pressing the "TEXT" button changes the display among PS, RT and frequency. - 2010 Subaru Legacy | Owner's Manual - Page 189
manually until the desired station frequency is displayed. 3. Press one of the preset buttons for more than 1.5 seconds to store the frequency. If the button is pressed for less than 1.5 seconds, the preceding selection will remain in memory. Using the Auto-store function, you can automatically - 2010 Subaru Legacy | Owner's Manual - Page 190
the audio system - Turn off the ignition switch . When you use the Auto-store install the SUBARU genuine satellite receiver (dealer option) and to enter into a contract. For details, please contact your SUBARU dealer. & XMTM satellite radio XMTM is a continental U.S. based satellite radio service - 2010 Subaru Legacy | Owner's Manual - Page 191
Audio 5-15 dealer signal loss include driving near a wall, steep cliff, hill or driving on the installed groundbased repeaters in heavily populated areas. However, you may still experience reception problems in some areas. you activate satellite radio and receive satellite radio customer support - 2010 Subaru Legacy | Owner's Manual - Page 192
5-16 Audio ! Channel selection by pressing the button ! Skip channel selection ! Category selection When in the SAT mode, briefly press the "SEEK" button " " or " " to select the - 2010 Subaru Legacy | Owner's Manual - Page 193
Audio 5-17 pressing the " will continue until the entire channel has been scanned from the low end to the high end. Press the "SCAN" button again to cancel the SCAN is broken for any reason such as vehicle maintenance or radio removal, all channels stored in the preset buttons are cleared. If this - 2010 Subaru Legacy | Owner's Manual - Page 194
disc will automatically return to track 1 (the first track on the disc) and will automatically play supported, and if inserted, they will be immediately ejected. . Copyright protected WMA/AAC files will not be played by the system. The player will automatically skip to the next file (track). . Audio - 2010 Subaru Legacy | Owner's Manual - Page 195
Audio was pressed. . The disc indicator steadily lights up if a disc is already inserted in standby mode. Press the "CD/AUX" button to start playback. ! Inserting a disc in a desired position will then be automatically drawn in, and the player will begin to play the first track on the - 2010 Subaru Legacy | Owner's Manual - Page 196
canceled, and the player will start playback of the disc inserted first. ! When CD is in the player (type A)/ When playing back all CDs in the player (type B) & How to play back a CD NOTE For type A audio stop blinking and will steadily light. 3. When the loading of a - 2010 Subaru Legacy | Owner's Manual - Page 197
Disc select buttons Press a desired one of the disc select buttons the disc number indicator of which steadily lights up. The player will then start playback of the selected CD, beginning with the first track. Turn the "TUNE/TRACK/CH" dial clockwise to skip to the beginning of the next track/file - 2010 Subaru Legacy | Owner's Manual - Page 198
track/file. Release the button to stop fast-reversing. Type A audio NOTE If you fast-reverse to the beginning of the first track/file (track), fast-reversing will stop and the player will start playback. NOTE If you fast-forward to the end of the last track/file (track), fast-forwarding will stop - 2010 Subaru Legacy | Owner's Manual - Page 199
on the CD. It is only possible to select this function for type B audio. To cancel the track/file (track) repeat-play mode, briefly press the " the "LOAD" button when there is free space in the CD magazine Type A audio NOTE . The "TRACK RPT" indication refers to the repeat playback of a single - 2010 Subaru Legacy | Owner's Manual - Page 200
RDM" button for 0.5 second or longer again (type A audio) or press the "RPT" button again (type B audio) and select CANCEL. The "RDM" indication will turn off lets you listen to the first 10 seconds of each track/file in succession. Press the "SCAN" button to start scanning upward beginning with the - 2010 Subaru Legacy | Owner's Manual - Page 201
is free space in the CD magazine . Turn off the power of the audio equipment . Turn the ignition switch to the "LOCK" position next one in the following sequence. For CD-DA: NOTE The display is designed to show titles for up to 30 characters. & Folder selection For MP3/WMA/AAC: ! - 2010 Subaru Legacy | Owner's Manual - Page 202
26 Audio "FOLDER" button starts playback beginning with the first track/file (track). & How to eject a CD from the player (type A) & How to eject CDs from the player (type B) NOTE . Avoid driving the vehicle with a CD sticking out, because vibration might make it fall out. . If you do not remove - 2010 Subaru Legacy | Owner's Manual - Page 203
Audio and "ALL EJECT" indicator will flash. 2. Remove the disc that has been ejected. The other discs disc type (i.e., 8 cm/3 inch CDs are not supported) and data format are correct. This player can this message remains displayed, please contact your SUBARU dealer. NOTE . If you press the " " - 2010 Subaru Legacy | Owner's Manual - Page 204
Owner's Manual of the portable audio player. . In some cases, when the sound volume of the portable audio player is low, the sound becomes bad when you turn up the volume of the vehicle audio system. In this case, adjust the sound volume of the portable audio player. . In some cases, noise occurs - 2010 Subaru Legacy | Owner's Manual - Page 205
Audio may not come out again, possibly causing the player to malfunction. . In cold and/or rainy weather, dew can form inside the CD player, preventing normal (for example, when the vehicle is driven on a rough surface). . To remove a disc from the case, press the center of the case and hold both - 2010 Subaru Legacy | Owner's Manual - Page 206
5-30 Audio there are deposits, wipe the disc surface from the center outward with a dry , do not use any disc that has a non-standard shape (for example, a heart shape). Malfunctions or problems might result. . A disc is vulnerable to heat. Never keep it either in places exposed to direct sunlight, - 2010 Subaru Legacy | Owner's Manual - Page 207
the steering wheel. They allow the driver to control audio functions without taking his/her hands off the steering wheel. *3: Only when an auxiliary audio product is connected. *4: Only when an iPod is connected using the iPod adapter that is available as a dealer option. & MODE button & " " and - 2010 Subaru Legacy | Owner's Manual - Page 208
switch is in the "Acc" or "ON" position. & Tips for the Hands-free system ! Bluetooth® & MUTE button (if equipped) NOTE Press this button if you wish to immediately cut the volume to zero. The audio display will show "MUTE". If you press the button again, the original sound volume will return and - 2010 Subaru Legacy | Owner's Manual - Page 209
cell phone is not connected to the Hands-free system. . The cell phone is behind the seat or in the glove box. . A metal material covers or touches the is connected. . Consult the dealer or an experienced radio/TV technician for help. NOTE This equipment has been tested and found to comply with - 2010 Subaru Legacy | Owner's Manual - Page 210
5-34 Audio would void the user's authority to operate this device. CAUTION . uses a full band and can avoid a band used by a movable body identification device. & Using the Hands-free system ! Turning on/off the Hands-free mode 1) 2) OFF hook switch ON hook switch To turn on the Hands-free - 2010 Subaru Legacy | Owner's Manual - Page 211
Audio 5-35 "TUNE/TRACK/CH" dial. 4. Select "Pair phone" by operating the "TUNE/TRACK/CH" dial. 5. Press the talk switch. Refer to "Voice command system" F5 "Add Entry" by operating the "TUNE/TRACK/CH" dial. 4. Select "Manual Input" by operating the "TUNE/TRACK/CH" dial. 5. Input the phone number - 2010 Subaru Legacy | Owner's Manual - Page 212
5-36 Audio If the registered name or phone number has more than 12 characters, press the "TEXT" button for more than 1.5 seconds to scroll the name or phone number. ! Making a phone call ! Making a phone call from the phone book It is possible to select a phone number from the phonebook registered - 2010 Subaru Legacy | Owner's Manual - Page 213
Audio 5-37 ! Menu list of the Hands-free system Turn the "TUNE/TRACK/CH" dial to select a menu, and then press the dial to enter the selected menu. NOTE For details about the operation, follow the voice guidance. - CONTINUED - - 2010 Subaru Legacy | Owner's Manual - Page 214
5-38 Audio First menu Phonebook* Second menu Add Entry Change Name List Names Speed Dial Delete Entry Del Spd Dial Go Back Third menu Adding a new number Details Changing a name registered in the phonebook Showing the list of the names registered in the phonebook Registering a speed dial - 2010 Subaru Legacy | Owner's Manual - Page 215
Audio 5-39 First menu Setup Second menu Security Third menu Set Pin Phbk Lock Phbk Changing the registered name of the cell phone Showing the list of the registered cell phones Changing the pass key Deleting the registered cell phone System setup Guidance Vol Initialize Go Back Setting the - 2010 Subaru Legacy | Owner's Manual - Page 216
5-40 Audio ! Voice command system The commands available for the voice command system are listed in the following chart. Command 1 2 3 4 5 6 7 8 9 book add entry phone book change name phone book delete entry phone book list names phone book set speed dial phone book delete speed dial phone book - 2010 Subaru Legacy | Owner's Manual - Page 217
Audio 5-41 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 set pass key list phone add entry delete entry delete speed dial by voice voice by phone phone call history by call history set speed dial next incoming outgoing list names set PIN phone book lock PIN setup send - 2010 Subaru Legacy | Owner's Manual - Page 218
---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- - 2010 Subaru Legacy | Owner's Manual - Page 219
console box ...Overhead console ...Pocket (if equipped) ... 6-5 6-6 6-6 6-8 6-8 Floor mat ...Cargo area cover (if equipped) ...Using the cover ...To remove the cover housing ...Stowage of the cargo area cover ...To install the cover housing ... 6-14 6-15 6-15 6-16 6-16 6-17 6 Cup holder ...Front - 2010 Subaru Legacy | Owner's Manual - Page 220
Map light & Dome light Models with moonroof 1) 2) 3) ON DOOR OFF The dome light switch has three positions: ON: The light remains on continuously. OFF: The light remains off. DOOR: The dome light illuminates automatically in the following cases. . Any of the doors or the rear gate (Outback) is - 2010 Subaru Legacy | Owner's Manual - Page 221
be changed by a SUBARU dealer. Contact your SUBARU dealer for details. & Cargo area light (Outback) 1) 2) 3) DOOR OFF ON 1) Door interlock switch Although the map light switches are in the OFF position (manually off), the map lights can be set to illuminate automatically in conjunction with - 2010 Subaru Legacy | Owner's Manual - Page 222
keyless entry transmitter. The setting of the period for which the lights remain on (OFF delay timer) can be changed by a SUBARU dealer. Contact your SUBARU dealer for details. Sun visors & Sun visor extension plate To have finished using it, stow it by pushing it toward the front of the vehicle. - 2010 Subaru Legacy | Owner's Manual - Page 223
Interior equipment 6-5 & Vanity mirror with light CAUTION Keep the vanity mirror cover closed while the car is being driven to avoid being blinded by glare. Storage compartment CAUTION . Always keep the storage compartment closed while driving to reduce the risk of injury in the event of sudden - 2010 Subaru Legacy | Owner's Manual - Page 224
6-6 Interior equipment & Glove box & Center console box ! Center console box (front) To use as storage space: 1) 2) Lock Unlock Pull out the divider plate of the dual cup holder. If you remove the divider plate from the dual cup holders, you can use the center console box as a storage space. - 2010 Subaru Legacy | Owner's Manual - Page 225
use again as cup holders: ment and a lower compartment. ! Upper compartment ! Lower compartment Insert the divider plate into the console box. ! Center console box (rear) 1) 1) Upper compartment lock release Lower compartment lock release Pull up the upper compartment lock release to open the - 2010 Subaru Legacy | Owner's Manual - Page 226
a cup from the cup holder or put a cup in the holder while you are driving, as this may distract you and lead to an accident. . Take care to avoid , push on the lid lightly and it will automatically open. CAUTION Do not use the pocket as an ashtray or leave a lighted cigarette in the pocket. This - 2010 Subaru Legacy | Owner's Manual - Page 227
Front passenger's cup holder CAUTION When a cup containing a beverage is in the cup holder, do not fold down or recline any seat. Otherwise, the beverage could spill while driving door pocket, make sure it is capped. Otherwise, the beverage could spill when opening/closing the door or while driving - 2010 Subaru Legacy | Owner's Manual - Page 228
in the center console Accessory power outlets are provided below the climate control, in the center console and in the cargo area. Electrical power (12V DC) from the battery is available at any of the to two or more outlets simultaneously, the total power consumed by them must not exceed 120W. - 2010 Subaru Legacy | Owner's Manual - Page 229
accessory power outlet for a long period of time while the engine is not running can cause battery discharge. . Before driving your vehicle, make sure that the plug and the cord on your electrical appliance will not interfere with your shifting gears and operating the accelerator and brake pedals - 2010 Subaru Legacy | Owner's Manual - Page 230
(if equipped) CAUTION Do not use ashtrays as waste receptacles or leave a lighted cigarette in an ashtray. This could cause a fire. Ashtray in the rear passenger's cup holder A portable ashtray is available from your SUBARU dealer. It fits into one of the cup holders built into the center console - 2010 Subaru Legacy | Owner's Manual - Page 231
accumulate around the hinges of the ashtray's inner lid. Clean them off using a toothbrush or another narrow-ended implement. Coat hook CAUTION Never hang anything on the coat hook that might obstruct the driver's view or that could cause injury in sudden stops or in a collision. And do not hang - 2010 Subaru Legacy | Owner's Manual - Page 232
6-14 Interior equipment Shopping bag hook CAUTION Do not hang items on the shopping bag hook that weigh 11 lbs (5 kg) or more. & Outback Floor mat & Legacy A shopping bag hook is attached to each side of the cargo area. To use the hook, push the upper portion and the shopping bag hook - 2010 Subaru Legacy | Owner's Manual - Page 233
in its proper location and correctly secured on its retaining pin. Also, do not use more than one floor mat. If the floor mat slips forward and interferes with the movement of the pedals during driving, it could cause an accident. Cargo area cover (if equipped) The cargo area cover is provided for - 2010 Subaru Legacy | Owner's Manual - Page 234
the lid, pull the handle up. 2. Hold down the button on the righthand rear quarter panel and lift up the right-hand cover housing. 3. Remove the cover housing. 3. Remove the left and right parts of the cargo floor lid. & Stowage of the cargo area cover The cargo area cover can be stowed in under - 2010 Subaru Legacy | Owner's Manual - Page 235
The convenient tie-down hooks are designed only for securing light cargo. Never try to secure cargo that exceeds the capacity of the hooks. The maximum load capacity is 44 lbs (20 kg) per hook. 1. To install the cover housing, insert both ends of the cover housing into the retainers. The cargo - 2010 Subaru Legacy | Owner's Manual - Page 236
located under the floor of the . Always keep the lid of the subfloor storage compartment closed while driving to reduce the risk of injury in the event of sudden stop other dangerous items in the subfloor storage compartment. Legacy Outback Hang the hook provided on the underside of the lid on - 2010 Subaru Legacy | Owner's Manual - Page 237
Legacy) or rear gate (Outback). When the ignition switch is "ON" and the shift lever (MT models) or select lever (AT or CVT models) is set to "R", the rear view camera automatically careful removing it. Otherwise, dealer for an inspection. Continued use may result in accident, fire or Legacy Outback - 2010 Subaru Legacy | Owner's Manual - Page 238
used for a long time while the engine is not operated, the battery may become completely discharged. . Under fluorescent light, the display may flicker. However, color of the objects. NOTE . Do not wipe the camera with alcohol, benzine or paint thinner. Otherwise, discoloration may occur. To remove - 2010 Subaru Legacy | Owner's Manual - Page 239
range on the screen Image from camera Range of view Range of view The area from the rear end of the bumper can be viewed. Areas at both ends of the bumper and areas just under the bumper cannot be viewed. Also, the image from the rear view camera looks shorter than the actual distance - 2010 Subaru Legacy | Owner's Manual - Page 240
vehicle width line) is a guide to help you realize the road The distance markers show the distance for a bumper (green horizontal line) Approx. 6.5 feet (2 m) from the bumper (green horizontal line) Approx. 3 feet (1 m) from the bumper (yellow horizontal line) Approx. 1.5 feet (0.5 m) from the bumper - 2010 Subaru Legacy | Owner's Manual - Page 241
When cargo is loaded, the rear view distance on the screen looks farther than the actual distance as in an upward slope. The distance marker shows the distance on the road. If there is a car or other object close behind, distance cannot be correctly displayed. - 2010 Subaru Legacy | Owner's Manual - Page 242
---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- - 2010 Subaru Legacy | Owner's Manual - Page 243
testing (U.S. only)...Preparing to drive ...Starting the engine...MT models ...AT and CVT models... 7-6 7-7 7-8 7-8 7-9 Power steering...Braking ...Braking tips...Brake system ...Disc brake pad wear warning indicators ... 7-23 7-23 7-23 7-24 7-24 Stopping the engine...Remote engine start system - 2010 Subaru Legacy | Owner's Manual - Page 244
a sulfur exhaust odor or smell. SUBARU recommends that you try a different brand of unleaded gasoline having lower sulfur to determine if the problem is fuel related before returning your vehicle to an authorized dealer for service. The CHECK ENGINE warning light/malfunction indicator lamp may also - 2010 Subaru Legacy | Owner's Manual - Page 245
Methylcyclopentadienyl Manganese Tricarbonyl). If you use such fuels, your emission control system performance may deteriorate and the CHECK ENGINE warning light/malfunction indicator lamp may turn on. If this happens, return to your authorized SUBARU Dealer for service. If it is determined that the - 2010 Subaru Legacy | Owner's Manual - Page 246
is in progress. slowly counterclockwise. WARNING . Gasoline vapor is highly flammable. Before refueling, always first stop the engine and close all vehicle doors and windows. Make sure that there are no lighted cigarettes, open flames or electrical sparks in the adjacent area. Refueling must be - 2010 Subaru Legacy | Owner's Manual - Page 247
Stop filling the tank after the fuel filler pump automatically turns off. Do not add any more fuel. NOTE CAUTION Make sure that the cap is tightened until it clicks to prevent fuel spillage in the event of an accident. 6. Put the cap back on, turn it clockwise until you hear a clicking noise. Be - 2010 Subaru Legacy | Owner's Manual - Page 248
fuel tank and emission control system may be damaged. It could also lead to fuel spillage and a fire. Immediately put fuel in the tank whenever the low fuel warning light illuminates. Engine misfires as a result of an empty tank could cause damage to the engine. State emission testing (U.S. only - 2010 Subaru Legacy | Owner's Manual - Page 249
part of the state emissions inspection. The OBD system is designed to detect engine and transmission problems that might cause vehicle emissions to exceed allowable limits. These inspections apply to all 1996 model year and newer passenger cars and light trucks. Over 30 states plus the District of - 2010 Subaru Legacy | Owner's Manual - Page 250
NOTE Engine oil, engine coolant, brake fluid, washer fluid and other fluid levels should be checked daily, weekly or at fuel stops. Starting the engine & MT models 1. Apply the parking brake. 2. Turn off unnecessary lights and accessories. 3. Depress the clutch pedal to the floor and shift - 2010 Subaru Legacy | Owner's Manual - Page 251
position without depressing the accelerator pedal. (4) If the engine still refuses to start, contact your nearest SUBARU dealer for assistance. 6. Confirm that all warning and indicator lights have turned off after the engine has started. The fuel injection system automatically lowers the idle speed - 2010 Subaru Legacy | Owner's Manual - Page 252
and braking more difficult. It could also result in accidental activation of the "LOCK" position on the ignition switch, causing the steering wheel to lock. The ignition switch should be turned off only when the vehicle is stopped and the engine is idling. Remote engine start system (dealer option - 2010 Subaru Legacy | Owner's Manual - Page 253
the front position lights will flash six times indicating that a vehicle door or trunk / rear gate was open when the remote engine start system was activated). . The brake pedal is depressed . The key was already in the ignition switch . The engine hood is opened . The remote start system "Service - 2010 Subaru Legacy | Owner's Manual - Page 254
there is a safety risk due to a vehicle related problem, the vehicle will shut down and the vehicle's horn will honk three times. NOTE . If the alarm system is armed at the time of remote engine start activation (the security indicator light on the combination meter is flashing), the alarm - 2010 Subaru Legacy | Owner's Manual - Page 255
Indicates that the engine is running via remote start. If the transmitter is removed outside of the operating range of the system, this sequence Models with automatic climate control system: After the system starts the engine, the automatic climate control system will activate the "FULL AUTO" mode - 2010 Subaru Legacy | Owner's Manual - Page 256
disabled to prevent the system from unexpectedly starting the engine while being serviced. To engage or disengage service mode: 1. Enter the vehicle and close all vehicle doors and the trunk/rear gate. 2. Verify that the select lever is in the "P" position (AT and CVT models) 3. Depress and hold - 2010 Subaru Legacy | Owner's Manual - Page 257
before removing them to ensure that the new batteries are inserted properly (battery "+" should be pointed away from the transmitter circuit board on both batteries). 4. Carefully snap the case halves back together, reinstall the phillips screw and test the remote engine start system. NOTE - 2010 Subaru Legacy | Owner's Manual - Page 258
7-16 Starting and operating ference, and (2) this device must accept any interference received transmission WARNING Do not drive the vehicle with the clutch disengaged (i.e., when the clutch pedal is depressed) or with the shift lever in the neutral position. Engine braking has no effect in either - 2010 Subaru Legacy | Owner's Manual - Page 259
lead to excessive engine wear and poor fuel economy. mph (km/h) Legacy Gear 1st 2nd 3rd 4th Non-turbo models 32 (52) 57 (92) 86 (139) 114 (184) Turbo models 35 (56) 62 (100) 94 (151) 125 (201) Outback 32 (52) 57 (92) 86 (139) 115 (185) NOTE Never exceed posted speed limits. & Driving tips Do - 2010 Subaru Legacy | Owner's Manual - Page 260
the transmission fluid to overheat. . Avoid shifting from one of the forward driving positions into the "R" position or vice versa until the vehicle has completely stopped. Such shifting may cause damage to the transmission. . When parking the vehicle, first securely apply the parking brake and - 2010 Subaru Legacy | Owner's Manual - Page 261
maximum fuel economy. At times, depending on varying driving conditions, a chain operating sound may be heard that is characteristic of this type of system. In this position, the transmission is mechanically locked to prevent the vehicle from rolling freely. When you park the vehicle, first apply - 2010 Subaru Legacy | Owner's Manual - Page 262
Starting and operating ! D (Drive) This position is for normal driving. The transmission automatically shifts into a suitable gear according to the vehicle speed and the acceleration you require. When more acceleration is required in this position, depress the accelerator pedal fully to the floor - 2010 Subaru Legacy | Owner's Manual - Page 263
manual mode. NOTE To prevent damage to the shift lock cover, cover the tip of the flat-head screwdriver with vinyl tape or a cloth before removing the cover. If the select lever does not move after performing the above procedure, the shift lock system may be malfunctioning. Contact a SUBARU dealer - 2010 Subaru Legacy | Owner's Manual - Page 264
the paddle switch twice in rapid succession. . The transmission automatically selects 1st gear when the vehicle stops moving. . If the temperature of the transmission fluid becomes too high, the "AT OIL TEMP" warning light will illuminate. Immediately stop the vehicle in a safe 1) 2) 3) Upshift - 2010 Subaru Legacy | Owner's Manual - Page 265
engine warms up. NOTE Right after the engine has been started and before it has warmed up, you may hear a noise coming from areas adjacent to the power steering pump which is located at the right-front area of the engine compartment. This noise is normal. It does not indicate power steering system - 2010 Subaru Legacy | Owner's Manual - Page 266
from the engine compartment. & Disc brake pad wear warning indicators CAUTION When you need to brake suddenly, continue depressing the brake pedal strongly to bring the effect of the brake assist. Brake assist is a driver assistance system. It assists the brake power when the driver cannot depress - 2010 Subaru Legacy | Owner's Manual - Page 267
shock in the brake pedal and hear the operating sound of ABS from the engine compartment just after the vehicle is started. This is caused by an automatic functional test of the ABS system being carried out and does not indicate any abnormal condition. The ABS warning light illuminates when the - 2010 Subaru Legacy | Owner's Manual - Page 268
12 km/h). . The warning light illuminates during driving. If these occur, have the ABS system repaired at the first available opportunity by your SUBARU dealer. voltage such as when the engine is jump started, the ABS warning light may illuminate. This is due to the low battery voltage and does not - 2010 Subaru Legacy | Owner's Manual - Page 269
. Drive carefully to the nearest SUBARU dealer and have the system inspected. 4. If both warning lights illuminate again and remain illuminated after the engine has been restarted, shut down the engine again, apply the parking brake, and check the brake fluid level. 5. If the brake fluid level - 2010 Subaru Legacy | Owner's Manual - Page 270
, the Vehicle Dynamics Control system adjusts the engine's output and the wheels' respective braking forces to help maintain traction and directional control. . Traction Control Function The traction control function is designed to prevent spinning of the driving wheels on slippery road surfaces - 2010 Subaru Legacy | Owner's Manual - Page 271
coming from the engine compartment. This noise is generated as a result of a check being performed on the Vehicle Dynamics Control system and is normal. . Depending on the timing of activation of the brakes, the brake pedal may seem to jolt when you drive off after starting the engine. This is - 2010 Subaru Legacy | Owner's Manual - Page 272
, drive with care and have an authorized SUBARU dealer carry out an inspection of those systems at the first available opportunity. control systems. The warning light illuminates when the ignition switch is turned to the "ON" position and turns off several seconds after the engine has started. This - 2010 Subaru Legacy | Owner's Manual - Page 273
an authorized SUBARU dealer carry out an inspection of that system at the first available opportunity. . The indicator light does not illuminate Pressing the switch to deactivate the Vehicle Dynamics Control system can facilitate the following operations. . a standing start on a steeply sloping - 2010 Subaru Legacy | Owner's Manual - Page 274
is activated, the Vehicle Dynamics Control operation indicator light illuminates. Tire pressure monitoring system (TPMS) (if equipped) WARNING If the low tire pressure warning light illuminates while driving, never brake suddenly and keep driving straight ahead while gradually reducing speed. Then - 2010 Subaru Legacy | Owner's Manual - Page 275
Starting and operating 7-33 low pressure threshold, the low tire pressure warning light should turn off a few minutes later. If this light still illuminates while driving after adjusting the tire pressure, a tire may have significant damage and a fast leak that causes the tire to lose air rapidly. - 2010 Subaru Legacy | Owner's Manual - Page 276
to prevent the vehicle from moving. . Never drive while the parking brake is applied because this will cause unnecessary wear on the brake linings. Before starting to drive, always make sure that the parking brake has been released and the brake system warning light has turned off. Your vehicle is - 2010 Subaru Legacy | Owner's Manual - Page 277
the accelerator pedal. However, the automatic release function does not operate under the following conditions. . Any door (other than the trunk lid or rear gate) is open. . The driver's seatbelt is not fastened. If the parking brake is automatically released, the brake system warning light and - 2010 Subaru Legacy | Owner's Manual - Page 278
off, the brake system warning light flashes and the system ignores any further pressing of the switch. To activate the switch again, turn the ignition switch to the "LOCK" position and restart the engine. . When the Hill Holder function is deactivated while the Hill Holder function has a malfunction - 2010 Subaru Legacy | Owner's Manual - Page 279
. . For AT and CVT models, put the select lever in the "P" (Park) position. Never rely on the transmission alone to hold the vehicle. When facing downhill, the front wheels should be turned into the curb. CAUTION If the brake system warning light flashes, the electronic parking brake system may be - 2010 Subaru Legacy | Owner's Manual - Page 280
may cause loss of vehicle control. . driving up or down a steep grade . driving on slippery or winding roads . driving in heavy traffic . When towing a trailer The cruise control indicator light on the combination meter will illuminate. 2. Depress the accelerator pedal until the vehicle reaches the - 2010 Subaru Legacy | Owner's Manual - Page 281
control set indicator light is illuminated in the combination meter. The vehicle will maintain the desired speed. Vehicle speed can be temporarily increased while driving with the cruise control activated. Simply depress the accelerator pedal to accelerate the vehicle. When the accelerator pedal is - 2010 Subaru Legacy | Owner's Manual - Page 282
Starting and operating & To change the cruising speed ! To increase the speed (by the "RES/ SET" switch) ! To increase the speed (by accelerator pedal) 1. Depress the accelerator pedal to accelerate km/h). This occurs because the cruise control system unit regards this operation as that intended to - 2010 Subaru Legacy | Owner's Manual - Page 283
depressing the accelerator pedal. & Cruise control indicator light ENGINE warning light/malfunction indicator lamp flash simultaneously during driving, have the vehicle checked by your nearest SUBARU dealer. & Cruise control set indicator light The cruise control indicator light illuminates when - 2010 Subaru Legacy | Owner's Manual - Page 284
---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- - 2010 Subaru Legacy | Owner's Manual - Page 285
New vehicle break-in driving - the first 1,000 miles (1,600 km) ...Fuel economy hints ...Engine exhaust gas (carbon monoxide)...Catalytic converter ...Periodic inspections ...Driving in foreign countries ...Driving tips for AWD vehicles ...Off road driving ...Legacy...Outback ...Rocking the vehicle - 2010 Subaru Legacy | Owner's Manual - Page 286
. . Avoid starting suddenly and rapid acceleration, except in an emergency. . Avoid hard braking, except in an emergency. The same break-in procedures should be applied to a newly installed or overhauled engine or when brake pads or brake linings are replaced with new ones. Fuel economy hints The - 2010 Subaru Legacy | Owner's Manual - Page 287
, you may hear a crackling sound coming from the exhaust system for a short time after the engine has been shut off. This sound is normal. 2.5 L turbo models 3.6 L models 2.5 L non-turbo models The catalytic converter is installed in the exhaust system. It serves as catalyst to reduce HC, CO and - 2010 Subaru Legacy | Owner's Manual - Page 288
to the heat shield of catalytic converter and the exhaust system. . Do not drive with an extremely low fuel level. Periodic inspections To keep your vehicle in the best condition at all times, always have the recommended maintenance services listed in the maintenance schedule in the "Warranty and - 2010 Subaru Legacy | Owner's Manual - Page 289
added traction during acceleration, and added engine braking force during deceleration. Therefore, your SUBARU AWD vehicle may handle differently than an ordinary two wheel drive vehicle and it contains some features unique to AWD. For safety purposes as well as to avoid damaging the AWD system, you - 2010 Subaru Legacy | Owner's Manual - Page 290
engine air intake or the exhaust pipe or water splashing onto electrical parts may damage your vehicle and may cause it to stall. & Outback Because of the AWD feature and higher ground clearance first aid kit and cell phone or citizens band radio. & Legacy Your AWD end over end. Avoid driving - 2010 Subaru Legacy | Owner's Manual - Page 291
several times to dry out the brake discs and brake pads. . Do not drive or park over or near flammable materials such as dry grass or fallen leaves, as they may burn easily. The exhaust system is very hot while the engine is running and right after the engine stops. This could create a fire hazard - 2010 Subaru Legacy | Owner's Manual - Page 292
the battery and cables. Cold temperatures reduce battery capacity. The battery must be in good condition to provide enough power for cold winter starts. Use an engine oil of proper grade and viscosity for cold weather. Heavy summer oil will cause harder starting. Keep the door locks from freezing by - 2010 Subaru Legacy | Owner's Manual - Page 293
in snowstorms. Snow will enter the engine's intake system and may hinder the air flow, which could result in engine shutdown or even breakdown. To prevent skidding and slipping, avoid sudden braking, abrupt acceleration, highspeed driving, and sharp turning when driving on snowy or icy roads. Always - 2010 Subaru Legacy | Owner's Manual - Page 294
braking on slippery surfaces, refer to "ABS (Anti-lock Brake System)" F7-25 and "Vehicle Dynamics Control system" F7-28. ! Wiper operation when snowing Before driving in cold place, then remove it. If you stop the vehicle at road side, use the hazard warning flasher to alert other drivers. Refer to - 2010 Subaru Legacy | Owner's Manual - Page 295
when trying to free the vehicle. When the road surface is extremely slippery, you can obtain better traction by starting the vehicle with the transmission in 2nd than 1st (for MT, AT and CVT). For information on holding the transmission in 2nd position, refer to "Selection of manual mode" F7-21. - 2010 Subaru Legacy | Owner's Manual - Page 296
luggage cover (Outback). Such items could tumble forward in the event of a sudden stop or a collision. This could cause serious injury. CAUTION Do not carry spray cans, containers with flammable or corrosive liquids or any other dangerous items inside the vehicle. NOTE For better fuel economy, do - 2010 Subaru Legacy | Owner's Manual - Page 297
Driving tips 8-13 & Vehicle capacity weight side door pillar. It includes the total weight of the driver and all passengers and their belongings, any optional equipment such as a trailer hitch, roof rack or bike carrier, etc., and the tongue load of a trailer. optional equipment and trailer - 2010 Subaru Legacy | Owner's Manual - Page 298
does not exceed NOTE . Remember that the vehicle's center of gravity is altered with the weight of the load on the roof, thus affecting the driving characteristics. Drive carefully, avoid rapid starts, hard cornering and abrupt stops. Crosswind effects will be increased. . Restore the bars to the - 2010 Subaru Legacy | Owner's Manual - Page 299
Driving tips 8-15 ! How to use as crossbars CAUTION . Do not raise the bar the bar. Otherwise the roof panel may be dented or the glass of the moonroof may be damaged. 1. Pull out the integrated crossbars from the roof rail holders by pulling up the covers. 3. Install the bars into the holders. - 2010 Subaru Legacy | Owner's Manual - Page 300
weight changes depending on the situation. For possible recommendations and limitations, refer to "Trailer towing" F8-19. . Trailer brakes out the crossbars from the roof rail holders by pulling up the covers. 3. Install the bars into the holders. 4. Make sure that the latches are fitted securely - 2010 Subaru Legacy | Owner's Manual - Page 301
models 3,000 lbs (1,360 kg) 2,700 lbs (1,224 kg) Maximum gross tongue weight & Connecting a trailer 1. Remove the receiver cover from the hitch receiver tube. Then insert the ball mount into the to "Trailer towing" F8-19. 1) 2) Hitch ball installation point Hooks for safety chains - CONTINUED - - 2010 Subaru Legacy | Owner's Manual - Page 302
be securely installed on the ball mount. 6. Connect your trailer to the hitch ball. 7. Connect the trailer and the hitch with safety chains that will hold the trailer's maximum gross weight. The chains should cross under the trailer tongue to prevent the tongue from dropping onto the ground in case - 2010 Subaru Legacy | Owner's Manual - Page 303
vehicle's engine, drivetrain, brakes, tires and suspension and has an adverse effect on fuel economy. If you do decide to tow a trailer, your safety and satisfaction depend upon proper use of correct equipment and cautious operation of your vehicle. Seek the advice of your SUBARU dealer to assist - 2010 Subaru Legacy | Owner's Manual - Page 304
) must never exceed the Gross Vehicle Weight Rating (GVWR). Gross Vehicle Weight (GVW) is the combined total of the weight of the vehicle, driver, passengers, luggage, trailer hitch, trailer tongue load and any other optional equipment installed on your vehicle. Therefore, the GVW changes depending - 2010 Subaru Legacy | Owner's Manual - Page 305
) Tongue load WARNING If the trailer is loaded with more weight in the back of trailer's axle than in the front, the load is taken off the rear axle of the towing vehicle. This may cause the rear wheels to skid, especially during braking or when vehicle speed is reduced during cornering, resulting - 2010 Subaru Legacy | Owner's Manual - Page 306
the front and approximately 40 percent in the rear. Also, distribute the load as evenly as possible on both the left and right sides. Be sure that all cargo is firmly secured to prevent a change in weight distribution while driving. CAUTION . Do not modify the vehicle exhaust system, brake system - 2010 Subaru Legacy | Owner's Manual - Page 307
's instructions for installation and use. Never use a hitch that mounts only to the rear bumper. The bumper is not designed to handle that type of load. For all types of hitches, regularly check that the hitch mounting bolts and nuts are tight. ! Legacy SUBARU does not offer accessory trailer - 2010 Subaru Legacy | Owner's Manual - Page 308
the vehicle's lighting circuit to increase its capacity and accommodate wiring changes. To ensure the trailer lights are connected properly, please consult your SUBARU dealer. Check for proper operation of the turn signals and the brake lights each time you hitch up. ! Tires road service to repair - 2010 Subaru Legacy | Owner's Manual - Page 309
more stopping distance when towing a trailer. Avoid sudden braking because it may result in skidding or jackknifing and loss of control. . Avoid abrupt starts and sudden accelerations. If your vehicle has a manual transmission, always start out in first gear and release the clutch at moderate - 2010 Subaru Legacy | Owner's Manual - Page 310
, the air conditioner may turn off automatically to protect the engine from overheating. . When driving uphill in hot weather, pay attention to the coolant temperature high warning light (for all models) and AT OIL TEMP warning light (for AT and CVT models) because the engine and transmission are - 2010 Subaru Legacy | Owner's Manual - Page 311
on the ground... 9-12 9-13 9-15 9-15 Flat tires...Changing a flat tire...Tire pressure monitoring system (TPMS) (if equipped)... 9-6 9-6 9-9 Jump starting ...How to jump start... 9-10 9-10 Engine overheating ...If steam is coming from the engine compartment... 9-12 9-12 Electronic parking brake - 2010 Subaru Legacy | Owner's Manual - Page 312
is replaced without the original pressure sensor/transmitter being transferred, the low tire pressure warning light will illuminate steadily after blinking for approximately one minute. This indicates the tire pressure monitoring system (TPMS) is unable to monitor all four road wheels. Contact your - 2010 Subaru Legacy | Owner's Manual - Page 313
mark . When the wear indicator appears on the tread, replace the tire. . The temporary spare tire must be used only on a rear wheel. If a front wheel tire gets punctured, replace the wheel with a rear wheel and install the temporary spare tire in place of the removed rear wheel. - CONTINUED - - 2010 Subaru Legacy | Owner's Manual - Page 314
9-4 In case of emergency 5) Tool bucket & Legacy the floor cover of the trunk. The electronic parking brake release tool is stored under the floor of the trunk. The other tools are stored in the tool bucket that is located in the recess of the spare tire wheel. For the - 2010 Subaru Legacy | Owner's Manual - Page 315
In case of emergency 9-5 & Outback 5) Tool bucket area. The electronic parking brake release tool is stored under the floor of the cargo area. The other tools are stored in the tool bucket that is located in the recess of the spare tire wheel. For - 2010 Subaru Legacy | Owner's Manual - Page 316
The tools and the spare tire are stored under the floor of the trunk (Legacy) or the cargo area (Outback). Refer to "Maintenance tools" F9-3. NOTE Make sure that the jack is well lubricated before using it. Legacy 4. Put wheel blocks at the front and rear of the tire diagonally opposite the flat - 2010 Subaru Legacy | Owner's Manual - Page 317
spare tire" F9-2 and strictly follow the instructions. 8. Place the jack under the side sill at the front or rear jack-up point closest to the flat tire. 9. Insert the jack handle into the jackscrew, and turn the handle until the tire clears the ground. Do not raise the vehicle higher than - 2010 Subaru Legacy | Owner's Manual - Page 318
Remove the wheel nuts and the flat tire. wheel nuts. Tighten them by hand. WARNING Do not use oil or grease on the wheel studs or nuts when the spare tire is installed torque. Have the wheel nut torque checked at the nearest automotive service facility. 11. Before putting the spare tire on, clean - 2010 Subaru Legacy | Owner's Manual - Page 319
is driven. Also, this system may not react immediately to a sudden drop in tire pressure (for example, a blow-out caused running over a sharp object). WARNING If the low tire pressure warning light illuminates while driving, never brake suddenly and keep driving straight ahead while gradually - 2010 Subaru Legacy | Owner's Manual - Page 320
a competent mechanic. & How to jump start 1. Make sure the booster battery is 12 volts and the negative terminal is grounded. 2. If the booster battery is in another vehicle, do not let the two vehicles touch. 3. Turn off all unnecessary lights and accessories. 4. Connect the jumper cables exactly - 2010 Subaru Legacy | Owner's Manual - Page 321
(−) terminal of the booster battery. Connect the other end of the cable to the strut mounting nut. Make sure that the cables are not near any moving parts and that the cable clamps are not in contact with any other metal. 5. Start the engine of the vehicle with the booster battery and run - 2010 Subaru Legacy | Owner's Manual - Page 322
up to the "MAX" mark. Refer to "Engine coolant" F11-18 for details. 5. If there is no coolant in the reserve tank, add coolant to the reserve tank. Then remove the radiator cap and fill the radiator with coolant. If you remove the radiator cap from a hot radiator, first wrap a thick cloth around the - 2010 Subaru Legacy | Owner's Manual - Page 323
out the jack handle from the trunk (Legacy) or cargo area (Outback). 2. Pry off the cover on the front bumper using a screwdriver, and you will to remove the towing hook after towing. Leaving the towing hook mounted on the vehicle could interfere with proper operation of the SRS airbag system in - 2010 Subaru Legacy | Owner's Manual - Page 324
the jack handle out of the trunk (Legacy) or cargo area (Outback). After towing, remove the towing hook from the vehicle and stow it in the tool bucket. Fit the towing hook cover on the bumper. WARNING Do not use the towing hook except when towing your vehicle. Front tie-down hooks: 3. Screw the - 2010 Subaru Legacy | Owner's Manual - Page 325
out. & Towing with all wheels on the ground & Using a flat-bed truck WARNING This is and CVT models or the shift lever into "1st" for MT models. 2. Apply the parking brake firmly. that the brake booster and power steering do not function when the engine is not running. Because the engine is - 2010 Subaru Legacy | Owner's Manual - Page 326
cannot be released WARNING . When the electronic parking brake cannot be released, the electronic parking brake system may malfunction. Driving in such conditions may cause an unexpected accident. Contact your SUBARU dealer for inspection as soon as possible. . You can release the electronic parking - 2010 Subaru Legacy | Owner's Manual - Page 327
tool. Have your SUBARU dealer release the electronic parking brake if necessary. In the event that you cannot release the electronic parking brake by pulling the electronic parking brake switch or by depressing the accelerator pedal, you can release the electronic parking brake manually by using the - 2010 Subaru Legacy | Owner's Manual - Page 328
brake. 6. Insert the electronic parking brake release tool into the cap of the parking brake release device. 7. Remove the cap of the parking brake release device by turning the electronic parking brake in the driver's seat. If the vehicle moves, the electronic parking brake has been released. - 2010 Subaru Legacy | Owner's Manual - Page 329
Trunk lid (Legacy) - if the trunk lid cannot be opened The trunk lid can also be opened using the key. Rear gate (Outback) - if the rear gate cannot be unlocked In the event that you cannot unlock the rear gate by operating the power door locking switches or the remote keyless entry system, you - 2010 Subaru Legacy | Owner's Manual - Page 330
-8. 4. Insert the hex-head wrench in the end of the motor shaft. To lower the moonroof, turn the wrench clockwise. To close the moonroof, turn the wrench counterclockwise. Have your vehicle checked and repaired by an authorized SUBARU dealer. 3. Remove the two screws that retain the moonroof switch - 2010 Subaru Legacy | Owner's Manual - Page 331
-2 10-2 10-3 10-3 Cleaning the interior...Seat fabric ...Leather seat materials...Synthetic leather upholstery...Climate control panel, audio panel, instrument panel, console panel, switches, combination meter, and other plastic surface ...Navigation monitor (if equipped) ... 10-5 10-5 10-5 10-5 10 - 2010 Subaru Legacy | Owner's Manual - Page 332
the brakes. . Do not wash the engine compartment and areas adjacent to it. If water enters the engine air intake, electrical parts or the power steering fluid reservoir, it will cause engine trouble or faulty power steering. . Outback: Since your vehicle is equipped with a rear wiper, automatic car - 2010 Subaru Legacy | Owner's Manual - Page 333
and apply them according to the manufacturer's instructions. Wax or polish when the painted surface luster or tone cannot be restored, lightly polish the surface with a fine- removing the paint layer and exposing the undercoat. When in doubt, it is always best to contact your SUBARU dealer or an auto - 2010 Subaru Legacy | Owner's Manual - Page 334
After the winter has ended, it is recommended that the underbody be given a very thorough washing. Before the beginning of winter, check the condition of underbody components, such as the exhaust system, fuel and brake lines, brake cables, suspension, steering system, floor pan, and fenders. If - 2010 Subaru Legacy | Owner's Manual - Page 335
used to remove difficult dirt a commercially-available fabric instructions. NOTE Strong cleaning agents such as solvents, paint thinners, window cleaner or gasoline must never be used on leather or synthetic interior materials. & Climate control panel, audio panel, instrument panel, console panel - 2010 Subaru Legacy | Owner's Manual - Page 336
damage the monitor's components. . Do not wipe the monitor with a hard cloth. Doing so could scratch the monitor. . Do not use cleaning fluid that contains thinner, gasoline, or any other volatile substance. Such cleaning fluid could erase the lettering on the switches at the bottom of the monitor. - 2010 Subaru Legacy | Owner's Manual - Page 337
...Removing air intake duct...Pulling off the fender lining ... 11-5 11-5 11-7 11-7 Continuously variable transmission fluid ...Front differential gear oil (AT and CVT models)...Checking the oil level ...Recommended grade and viscosity ... 11-26 11-26 11-26 11-27 Engine hood ...Engine compartment - 2010 Subaru Legacy | Owner's Manual - Page 338
fuse...Installation of accessories ...Replacing bulbs ...Headlight...Front turn signal light ...Front position light ...Front fog light (if equipped)...Rear combination lights ...Tail/Back-up light (Outback) ...License plate light ...Dome light...Map light ...Vanity mirror light ...Door step light - 2010 Subaru Legacy | Owner's Manual - Page 339
to support the vehicle. . Never keep the engine running in a poorly ventilated area, such as a garage or other closed areas. . Do not smoke or allow open flames around the fuel or battery. This will cause a fire. . Because the fuel system is under pressure, replacement of the fuel filter should - 2010 Subaru Legacy | Owner's Manual - Page 340
engine coolant, brake fluid or any other fluid on hot engine components. This may cause a fire. . Always remove the key from the ignition switch. When the ignition switch is in the "ON" position, the cooling fan may operate suddenly even when the engine is stopped. . Before performing any servicing - 2010 Subaru Legacy | Owner's Manual - Page 341
fan, belts and any other moving engine parts. Removing rings, watches and ties is advisable. Maintenance tips Some clips and fender linings must be removed before replacing the air cleaner elements or specific bulbs. & Removing and reinstalling clips ! Removing clips There are several types of - 2010 Subaru Legacy | Owner's Manual - Page 342
11-6 Maintenance and service the illustration. 2. Pull the protruded center portion to remove the entire body of the clip. ! Type C clips ! Reinstalling clips Type C clips Type A clips Insert the clip without the center portion first and then push the center portion of the clip into the hole. - 2010 Subaru Legacy | Owner's Manual - Page 343
on the air intake duct, then remove the air intake duct. Refer to "Type A clips" F11-5. 3. Remove the clip from the fender lining. Refer to "Type B clips" F11-5. & Pulling off the fender lining It is necessary to pull off the fender lining when replacing some bulbs. 1. Start the engine and turn - 2010 Subaru Legacy | Owner's Manual - Page 344
hood is properly locked before you start driving. If it is not, it might fly open while the vehicle is moving and block your view, which may cause an accident and serious bodily injury. 3. Release the secondary hood release by moving the lever between the front grille and the hood toward the left - 2010 Subaru Legacy | Owner's Manual - Page 345
11-29) 2) Manual transmission oil level gauge (MT) (page 11-23) 3) Clutch fluid reservoir (page 11-31) 4) Brake fluid reservoir (page 11-30) 5) Fuse box (page 11-48) 6) Battery (page 11-47) 7) Windshield washer tank (page 11-42) 8) Engine oil filler cap (page 11-12) 9) Engine coolant reservoir (page - 2010 Subaru Legacy | Owner's Manual - Page 346
and service 1) Power steering fluid reservoir (page 11-29) 2) Manual transmission oil level gauge (MT) (page 11-23) 3) Clutch fluid reservoir (page 11-31) 4) Brake fluid reservoir (page 11-30) 5) Fuse box (page 11-48) 6) Battery (page 11-47) 7) Windshield washer tank (page 11-42) 8) Engine oil - 2010 Subaru Legacy | Owner's Manual - Page 347
gauge (AT) (page 11-26) 3) Automatic transmission fluid level gauge (page 11-24) 4) Brake fluid reservoir (page 11-30) 5) Fuse box (page 11-48) 6) Battery (page 11-47) 7) Windshield washer tank (page 11-42) 8) Engine oil filler cap (page 11-12) 9) Engine coolant reservoir (page 11-18) 10) Radiator - 2010 Subaru Legacy | Owner's Manual - Page 348
to drain back into the oil pan before checking the level. NOTE . When the engine low oil level warning light illuminates, have your vehicle inspected by your SUBARU dealer as soon as possible. . The engine oil consumption rate is not stabilized, and therefore cannot be determined until the vehicle - 2010 Subaru Legacy | Owner's Manual - Page 349
exhaust pipe, be sure to wipe it off. NOTE . To prevent overfilling the engine oil, do not add any additional oil above the upper level when the engine is cold. . In 2.5 L engine models, the level gauge has a notch above the upper level. Just after driving or while the engine is warm, the engine - 2010 Subaru Legacy | Owner's Manual - Page 350
short trips are frequently made, or when driving in extremely cold weather. 1. Warm up the engine by letting the engine idle for approximately 10 minutes to ease draining the engine oil. 2. Park the vehicle on a level surface and stop the engine. 3. Remove the oil filler cap. properly. WARNING Be - 2010 Subaru Legacy | Owner's Manual - Page 351
after the seal makes contact with the bottom of engine. Model 2.5 L models 3.6 L models Oil filter color Black Blue Black Part number 15208AA100 15208AA12A 15208AA031 Amount of rotation 1 rotation 7/8 rotation 3/4 rotation Oil capacity (guideline): 2.5 L models: 4.2 US qt (4.0 liters, 3.5 Imp qt - 2010 Subaru Legacy | Owner's Manual - Page 352
is preferred. API Service label 1) Indicates the oil quality by API designations 2) Indicates the SAE oil viscosity grade 3) Indicates that the oil has fuel saving capabilities Engine oil viscosity (thickness) affects fuel economy. Oils of lower viscosity provide better fuel economy. However, in - 2010 Subaru Legacy | Owner's Manual - Page 353
service 11-17 & Recommended grade and viscosity under severe driving Fuses" F11-48 and "Fuses and circuits" F12-6. If the fuse is not blown, have the cooling system checked by your SUBARU dealer. If frequent addition of coolant is necessary, there may be a leak in the engine cooling system - 2010 Subaru Legacy | Owner's Manual - Page 354
Booklet". Check the coolant level at each fuel stop. 1. Check the coolant level on the outside of the reservoir while the engine is cool. 2. If the level is close to or lower than the "LOW" level mark, add coolant up to the "FULL" level mark. If the reserve tank is empty, remove the radiator cap - 2010 Subaru Legacy | Owner's Manual - Page 355
Maintenance and service 11-19 1. Remove the under cover. drain plug and loosen the drain plug. 3. Loosen the radiator cap to drain the coolant from the radiator. Then drain the coolant from the reserve tank. Tighten the drain plug securely. 4. Install the under cover. Coolant capacity (guideline - 2010 Subaru Legacy | Owner's Manual - Page 356
the engine with the air cleaner element removed. The air cleaner element not only filters intake air but also stops flames if the engine backfires. If the air cleaner element is not installed when the engine backfires, you could be burned. 6. Pour the coolant and fill to the reservoir tank's "FULL - 2010 Subaru Legacy | Owner's Manual - Page 357
recommended that you always use genuine SUBARU parts. ! Non-turbo models 1. Remove the air intake duct (except 3.6 L models). For the method to remove the air intake duct, refer to "Removing air intake duct" F11-7. to the top of the air cleaner case. 3. Loosen the screw of the clamp. 4. Unsnap the - 2010 Subaru Legacy | Owner's Manual - Page 358
11-22 Maintenance and service ! Turbo models 3. Clean the inside of the air cleaner cover and case with a damp cloth and install a new air cleaner element. 4. Snap the two clamps on the air cleaner case cover. Spark plugs It may be difficult to replace the spark plugs. It is recommended that you - 2010 Subaru Legacy | Owner's Manual - Page 359
Maintenance and service 11-23 Drive belts It is unnecessary to check the deflection of the drive belt periodically because your engine is equipped with an automatic belt tension adjuster. However, replacement of the belt should be done according to the maintenance schedule in the "Warranty and - 2010 Subaru Legacy | Owner's Manual - Page 360
the temperature of the transmission fluid up to normal operating temperature; 158 to 1768F (70 to 808C) is normal. 2. Park the vehicle on a level surface and set the parking brake. 3. First shift the select lever in each position. Then shift it in the "P" position, and run the engine at idling speed - 2010 Subaru Legacy | Owner's Manual - Page 361
careful not to spill automatic transmission fluid when adding it. If automatic transmission fluid touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If automatic transmission fluid gets on the exhaust pipe, be sure to wipe it off. 1) 2) 3) 4) HOT range COLD range Upper level - 2010 Subaru Legacy | Owner's Manual - Page 362
and service Continuously variable transmission fluid There is no continuously variable transmission fluid level gauge. It is unnecessary to check the continuously variable transmission fluid level. However, if necessary, we recommend that you consult your SUBARU dealer for inspection. Front - 2010 Subaru Legacy | Owner's Manual - Page 363
Maintenance and service 11-27 & Recommended grade and viscosity Each oil manufacturer has its own base oils and additives differential gear oil & Checking the gear oil level 3) Oil level SAE viscosity No. and applicable temperature CVT models (Legacy) 1) Filler plug 2) Drain plug - CONTINUED - - 2010 Subaru Legacy | Owner's Manual - Page 364
If rear differential gear oil gets on the exhaust pipe, be sure to wipe it off. . If the vehicle requires frequent refilling, there may be an oil leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer. & Recommended grade and viscosity 3.6 1) 2) 3) L models Filler plug Drain - 2010 Subaru Legacy | Owner's Manual - Page 365
as its temperature rises; the fluid level differs according to fluid temperature. Therefore, the reservoir tank has two different checking ranges for hot and cold fluids. Check the power steering fluid level monthly. 1. Park the vehicle on a level surface, and stop the engine. SAE viscosity No. and - 2010 Subaru Legacy | Owner's Manual - Page 366
is extreme low, it may indicate possible leakage. Consult your SUBARU dealer for inspection. Brake fluid & Checking the fluid level WARNING . Never let brake fluid contact your eyes because brake fluid can be harmful to your eyes. If brake fluid gets in your eyes, immediately flush them thoroughly - 2010 Subaru Legacy | Owner's Manual - Page 367
brake fluids even if they are the same brand. CAUTION . Clutch fluid absorbs moisture from the air. Any absorbed moisture can cause improper clutch operation. . If the vehicle requires frequent refilling, there may be a leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer - 2010 Subaru Legacy | Owner's Manual - Page 368
11-32 Maintenance and service Use only clutch fluid from a sealed container. Brake booster If the brake booster does not operate as described in the following procedure, have it checked by your SUBARU dealer. 1. With the engine off, depress the brake pedal several times, applying the same pedal - 2010 Subaru Legacy | Owner's Manual - Page 369
. 2. Start the vehicle by releasing the pedal slowly to check that the engine and transmission smoothly couple without any sign of slippage. 1) More than 2.56 in (65 mm) 1) 0.08 - 0.18 in (2 - 5 mm) Stop the engine and firmly depress the brake pedal several times. Lightly pull the brake pedal - 2010 Subaru Legacy | Owner's Manual - Page 370
Replacement of brake pad and lining CAUTION If you continue to drive despite the scraping noise from the audible brake pad wear indicator, it will result in the need for costly brake rotor repair or replacement. you apply the brake pedal, have the brake pads serviced by your SUBARU dealer as soon - 2010 Subaru Legacy | Owner's Manual - Page 371
). If you adjust the tire pressures in a warm garage and will then drive the vehicle in cold outside air, the resulting drop in tire pressures may cause the low tire pressure warning light to illuminate. To avoid this problem when adjusting the tire pressures in a warm garage, inflate the tires to - 2010 Subaru Legacy | Owner's Manual - Page 372
blinking for approximately one minute, you should have your Tire Pressure Monitoring System checked at a SUBARU dealer as soon as possible. If this light illuminates while driving, never brake suddenly and keep driving straight ahead while gradually reducing speed. Then slowly pull off the road - 2010 Subaru Legacy | Owner's Manual - Page 373
example, during a fuel stop) and before any long journey. Check the tire pressures when the tires are cold. Use a pressure gauge to adjust the tire pressures to the values shown on the tire placard. The tire placard is located on the door pillar on the driver's side. Driving even a short distance - 2010 Subaru Legacy | Owner's Manual - Page 374
becomes warm. . The tires are considered cold when the vehicle has been parked for at least 3 hours or has been driven less than 1 mile (1.6 km). . Correct tire pressure (tread worn evenly) . Abnormally low tire pressure (tread worn at shoulders) WARNING Do not let air out of warm tires to adjust - 2010 Subaru Legacy | Owner's Manual - Page 375
*: The suspension system is designed to hold each wheel at a certain alignment (relative to the other wheels and to the road) for optimum straight-line stability and cornering performance. 1) 2) 3) New tread Worn tread Tread wear indicator WARNING Driving at high speeds with excessively low tire - 2010 Subaru Legacy | Owner's Manual - Page 376
service Front Example of tire rotation direction mark 1) Front If the tire has a rotation direction specification, the tire rotation direction mark is placed on its sidewall. When you install a tire that has the tire rotation direction mark, install driving approximately 600 miles (1,000 km), - 2010 Subaru Legacy | Owner's Manual - Page 377
the best possible combination of running performance, ride comfort, and service life. It is essential for every tire to have a braking performance, speedometer accuracy and odometer accuracy. It also creates incorrect body-to-tire clearances and inappropriately changes the vehicle's ground clearance - 2010 Subaru Legacy | Owner's Manual - Page 378
CAUTION Never use engine coolant as washer fluid because it could cause paint damage. If you spray washer fluid on the windshield but the windshield washer fluid warning light illuminates or the supply of washer fluid runs out, add washer fluid in the tank. Remove the washer tank filler cap, then - 2010 Subaru Legacy | Owner's Manual - Page 379
cold weather protection without damaging your vehicle's paint, wiper blades or washer system. CAUTION Never use engine coolant as washer fluid the passenger-side wiper arm, first raise the driver-side wiper arm. Otherwise, the passenger-side wiper assembly and driver-side wiper assembly will touch - 2010 Subaru Legacy | Owner's Manual - Page 380
illustration. 3. Install the wiper blade assembly to the wiper arm. Make sure that it locks in place. 4. Hold the wiper arm by hand and slowly lower it in position. 1. Grasp the locked end of the blade rubber assembly and pull it firmly until the stoppers on the rubber are free of the support. - 2010 Subaru Legacy | Owner's Manual - Page 381
the new blade rubber is not provided with two metal spines, remove the metal spines from the old blade rubber and install them in the new blade rubber. 1) 2) Claw Stopper 4. Be sure to position the claws at the end of the support between the stoppers on the rubber as shown. If the rubber is - 2010 Subaru Legacy | Owner's Manual - Page 382
11-46 Maintenance and service & Rear window wiper blade rubber (Outback) 2. Pull the blade rubber assembly out of the plastic support. 3. Pull the wiper blade assembly toward you to remove it from the wiper arm. 1) Metal spines 1. Pull out the end of the blade rubber assembly to unlock it from - 2010 Subaru Legacy | Owner's Manual - Page 383
Maintenance and service 11-47 ends. If the rubber is not retained properly, the wiper may scratch the rear window glass. 5. Install the fluid contact eyes, skin, fabrics, or paint because battery fluid is a corrosive acid. If battery fluid gets on your skin or in your eyes, immediately flush - 2010 Subaru Legacy | Owner's Manual - Page 384
and service remove rings wellventilated area. . Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the fluid level or periodically refill with One is located under the instrument panel behind the fuse box cover on the driver's seat side. To remove - 2010 Subaru Legacy | Owner's Manual - Page 385
The other one is housed in the engine compartment. The fuse puller is stored in the main fuse box in the engine compartment. The spare fuses are stored in the main fuse box cover in the engine compartment. 1) 2) Good Blown If any lights, accessories or other electrical controls do not operate - 2010 Subaru Legacy | Owner's Manual - Page 386
11-50 Maintenance and service Main fuse Installation of accessories Always consult your SUBARU dealer before installing fog lights or any other electrical equipment in your vehicle. Such accessories may cause the electronic system to malfunction if they are incorrectly installed or if they are - 2010 Subaru Legacy | Owner's Manual - Page 387
. ! Low beam light bulbs 1. Pull off the fender lining. For details, refer to "Pulling off the fender lining" F117. 3. Disconnect the electrical connector. 5. Replace the bulb, then set the retainer spring securely. 6. Reconnect the electrical connector. 7. Install the bulb cover. 4. Remove the - 2010 Subaru Legacy | Owner's Manual - Page 388
beam light bulbs 1. Remove the air intake duct (right-hand side). For the method to remove the air intake duct, refer to "Removing air intake duct" F11-7. surface. 6. Reconnect the electrical connector. 7. To install the bulb to the headlight assembly, turn it clockwise until it clicks. 8. Install - 2010 Subaru Legacy | Owner's Manual - Page 389
socket and replace the bulb with a new one. & Front fog light (if equipped) NOTE It may be difficult to replace the bulbs. We recommend that you have the bulbs replaced by your SUBARU dealer if necessary. 4. After replacing the bulbs, reposition the protective cover of the engine com1. Pull off the - 2010 Subaru Legacy | Owner's Manual - Page 390
Pull out the socket. 5. Pull out the bulb from the socket and replace the bulb with a new one. & Rear combination lights ! Legacy NOTE It may be difficult to replace the bulbs. We recommend that you have the bulbs replaced by your SUBARU dealer if necessary. 2. Disconnect the electrical connector - 2010 Subaru Legacy | Owner's Manual - Page 391
Maintenance and service 11-55 ! Outback 1) 2) 3) Brake/tail and rear side marker light Rear turn signal light Back-up light 2. Remove the bulb holder from the rear combination light assembly by turning it counterclockwise. Use pliers if necessary. 3. Pull the bulb out of the bulb holder and - 2010 Subaru Legacy | Owner's Manual - Page 392
11-56 Maintenance and service & Tail/Back-up light (Outback) 1) 2) 3) Tail and rear side marker light Brake light Rear turn signal light 5. Remove the bulb holder from the rear combination light assembly by turning it counterclockwise. 6. Pull the bulb out of the bulb holder and replace it with - 2010 Subaru Legacy | Owner's Manual - Page 393
your SUBARU dealer if necessary. 1) 2) Back-up light Tail light 1. Open the trunk. 2. Turn the bulb socket counterclockwise and remove it. 3. Turn the bulb socket counterclockwise and remove it. 4. Pull the bulb out of the bulb socket and replace it with a new one. 5. Install the bulb socket by - 2010 Subaru Legacy | Owner's Manual - Page 394
11-58 Maintenance and service ! Outback 4. Install a new bulb. 5. Reinstall the lens. 6. Tighten the mounting screws. & Dome light 1. Remove the mounting screws using a Phillips screwdriver. 2. Remove the lens. 1. Remove the lens by prying the edge of the lens with a flat-head screwdriver. 2. - 2010 Subaru Legacy | Owner's Manual - Page 395
edge of the lens with a flat-head screwdriver. 2. Pull the bulb out of the socket. 3. Install a new bulb. 4. Reinstall the lens. 1. Remove the lens by prying the edge of the lens with a flat-head screwdriver. 2. Turn the bulb until the flat surfaces at its ends are aligned vertically. Pull the - 2010 Subaru Legacy | Owner's Manual - Page 396
11-60 Maintenance and service & Door step light 4. Reinstall the lens. & Cargo area light (Outback) 2. Pull the bulb out of the socket. 3. Install a new bulb. 4. Reinstall the lens. & Trunk light (Legacy) 1. Remove the lens by prying the edge of the lens with a flat-head screwdriver. 1. - 2010 Subaru Legacy | Owner's Manual - Page 397
Specifications ...Dimensions...Engine ...Electrical system...Capacities ...Tires ...Wheel alignment ... 12-2 12-2 12-3 12-3 12-4 12-5 12-5 Fuses and circuits ...Fuse panel located in the passenger compartment ...Fuse panel located in the engine compartment ... 12-6 12-6 12-8 Bulb chart...Vehicle - 2010 Subaru Legacy | Owner's Manual - Page 398
& Dimensions in (mm) Item Drive system Transmission type Overall length Overall width Overall height Wheelbase Tread Front Rear Ground clearance*1 *1: Measured with vehicle empty *2: Measured when roof rails are used as crossbars *3: Measured when roof rails are not used as crossbars AT: Automatic - 2010 Subaru Legacy | Owner's Manual - Page 399
(92.0 6 91.0) 10.5 : 1 1-6-3-2-5-4 8.4 : 1 Horizontally opposed, liquid cooled 4 cylinder, 4 stroke gasoline engine 150 (2,457) 3.92 6 3.11 (99.5 6 79.0) & Electrical system Battery type and capacity (5HR) Alternator Spark plugs 2.5 L models 3.6 L models 2.5 L non-turbo models 2.5 L turbo models - 2010 Subaru Legacy | Owner's Manual - Page 400
12-4 Specifications & Capacities Fuel tank Engine oil Transmission oil (MT) Transmission fluid (CVT) Transmission fluid (AT) Front differential gear oil (AT and CVT models) Rear differential gear oil Power steering fluid Engine coolant 2.5 L non-turbo models MT CVT 2.5 L turbo models 3.6 L models - 2010 Subaru Legacy | Owner's Manual - Page 401
& Tires Tire size Wheel size Pressure Temporary spare tire Front Rear Size Pressure P205/60R16 91V 16 6 6 1/2JJ psi (210 kPa) T145/80R17 60 psi (420 kPa) & Wheel alignment Item Toe Front Rear Camber Front Rear −0830' −1800' Legacy 2.5 L non-turbo models Except 2.5 L non-turbo models Toe in 0 in (0 - 2010 Subaru Legacy | Owner's Manual - Page 402
power window (left side) Power window (driver's side) Navigation system Front wiper deicer Moonroof Combination meter Remote control view mirrors Integrated unit Stop light Seat heater relay Power supply (battery) Turn signal unit Integrated unit Automatic transmission unit rear 5 6 7 8 9 10 11 12 - 2010 Subaru Legacy | Owner's Manual - Page 403
window Fuse panel 28 29 30 31 Fuse rating Empty 20A Empty 7.5A Empty 7.5A ... Circuit Power window (passenger's side) Automatic tioner unit air condi- Front wiper deicer Back-up light Electronic parking brake unit Hill Holder system unit Accessory power outlet Starter relay Air conditioner Audio - 2010 Subaru Legacy | Owner's Manual - Page 404
engine compartment Fuse panel 1 2 3 4 5 6 7 8 9 Fuse rating 7.5A 7.5A 7.5A 15A 15A 20A 10A 10A 20A ... Circuit CVT control unit Horn LO Horn HI Low beam (right side) Low beam (left side) Fuel pump High beam headlight (left side) High beam headlight (right side) Continuously variable transmission - 2010 Subaru Legacy | Owner's Manual - Page 405
unit Automatic transmission control unit Illumination Rear combination light Turn and hazard warning flasher (body control unit) Door lock (body control unit) Rear wiper Rear washer Front washer Front wiper Rear window defogger Mirror heater Front wiper deicer Blower fan Blower fan Fuse panel 28 - 2010 Subaru Legacy | Owner's Manual - Page 406
12-10 Specifications Bulb chart NOTE Lights A and B are the LED (Light Emitting Diode) type. Consult your SUBARU dealer for replacement. - 2010 Subaru Legacy | Owner's Manual - Page 407
headlight Front position light Low beam headlight Front turn signal light Map light Dome light Door step light Front fog light Front side marker light Vanity mirror light Cargo area light Back-up light (Outback) Tail light (Outback) Licence plate light (Outback) Rear turn signal light (Outback) 12V - 2010 Subaru Legacy | Owner's Manual - Page 408
a burn injury. Brake/Tail and rear side marker light 12V-21/5W (Legacy) License plate light (Legacy) Back-up light (Legacy) Rear turn signal light (Legacy) High mount stop light (Outback) High mount stop light (Legacy) 12V-5W 12V-16W 12V-21W - - CAUTION Replace any bulb only with a new bulb of the - 2010 Subaru Legacy | Owner's Manual - Page 409
Specifications 12-13 Vehicle identification 1) 2) 3) 4) 5) 6) 7) 8) Emission control label Vehicle identification number Certification and bar code label Tire inflation pressure label Vehicle identification number plate Model number label Fuel label Air conditioner label - 2010 Subaru Legacy | Owner's Manual - Page 410
---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- - 2010 Subaru Legacy | Owner's Manual - Page 411
Consumer information and Reporting safety defects For U.S.A...Tire information ...13-2 13-2 Determining compatibility of tire and vehicle load capacities - how to determine...13-11 Uniform tire quality grading standards ...Treadwear ...Traction AA, A, B, C...Temperature A, B, C... 13-15 13-16 13-16 - 2010 Subaru Legacy | Owner's Manual - Page 412
13-2 Consumer information and Reporting safety defects For U.S.A. The following information has been is a brief review of the tire sizing system with a breakdown of its individual elements. ! P Metric (1) P = Certain tire type used on light duty vehicles such as passenger cars (2) Section Width - 2010 Subaru Legacy | Owner's Manual - Page 413
Consumer rated load. (7) Speed Rating: An alphabetical system describing a tire's capability to travel at first two figures identify the week, starting with "01" to represent the first a brief review of the TIN with a breakdown of its individual elements. The maximum cold inflation pressure - 2010 Subaru Legacy | Owner's Manual - Page 414
13-4 Consumer information and Reporting safety defects ! Maximum load rating The load rating at the maximum permissible weight load for this tire. For example, "MAX. LOAD 615 kg (1,356 LBS) @ 350 kpa (51 PSI) MAX. PRESS." WARNING STEEL + 2 POLYESTER + 1 NYLON SIDEWALL 2 POLYESTER" ! Uniform - 2010 Subaru Legacy | Owner's Manual - Page 415
Consumer information and Reporting safety defects 13-5 & Recommended tire inflation pressure ! Recommended cold tire inflation pressure Recommended cold tire inflation pressure for your vehicle's tires is as follows. Tire size Wheel size Pressure Front Rear Tempor- Size ary spare Pressure tire - 2010 Subaru Legacy | Owner's Manual - Page 416
adjusting air pressure to achieve proper inflation Canada-spec. models The vehicle placard is affixed to the driver's side B-pillar. Example: The vehicle placard shows original tire size, recommended cold tire inflation pressure on each tire at maximum loaded vehicle weight, seating capacity and - 2010 Subaru Legacy | Owner's Manual - Page 417
tire The combined weight (in excess of those standard items which may be replaced) of automatic transmission, power steering, power brakes, power windows, power seats, radio, and heater, to the extent that these items are available as factory-installed equipment (whether installed or not). . Bead - 2010 Subaru Legacy | Owner's Manual - Page 418
of tread, sidewall, or innerliner that extends to cord material. . Outer diameter The sum of: (a) Curb weight (b) Accessory weight (c) Vehicle capacity weight (d) Production options weight pressure The overall diameter of an inflated new tire. . Overall width A mechanical device made of rubber - 2010 Subaru Legacy | Owner's Manual - Page 419
Consumer information and Reporting safety defects 13-9 sory weight, including heavy duty brakes, ride levelers, roof rack The cold inflation pressure capacity. . Vehicle maximum load on the tire The parting of the rubber compound from the cord material in the sidewall. . Test rim A metal support - 2010 Subaru Legacy | Owner's Manual - Page 420
13-10 Consumer information and Reporting safety defects accessory weight, and normal occupant weight (distributed in accordance with Table 1 that is appended to the end of this section) and dividing by 2. . Wheel-holding fixture Table 1 - Occupant loading and distribution for vehicle normal load - 2010 Subaru Legacy | Owner's Manual - Page 421
be replaced immediately. With a tire in this condition, driving at even low speeds in wet weather can cause the vehicle to hydroplane. capacity includes the total weight of driver and all passengers and their belongings, any cargo, any optional equipment such as a trailer hitch, roof rack or bike - 2010 Subaru Legacy | Owner's Manual - Page 422
Consumer information and Reporting safety defects ! Calculating total and load capacities varying seating configurations Calculate the available load capacity total weight. Example 1B 2. Calculate the available load capacity by subtracting the total weight from the vehicle capacity weight of 800 - 2010 Subaru Legacy | Owner's Manual - Page 423
the available load capacity. 3. The total weight now exceeds the capacity weight by 81 lbs (37 kg), so the cargo weight must be reduced by 81 lbs (37 kg) or more. Example 2A 3. The result of step 2 shows that a further 172 lbs (78 kg) of cargo can be carried. Example 2B Vehicle capacity weight of - 2010 Subaru Legacy | Owner's Manual - Page 424
is referred to Gross Vehicle Weight Rating (GVWR). And each axle's maximum loaded capacity is referred to Gross Axle Weight Rating (GAWR). The GVWR and each axle's GAWR are shown on the vehicle certification label affixed to the driver's door. The GVWR and front and rear GAWRs are determined by - 2010 Subaru Legacy | Owner's Manual - Page 425
vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. Uniform tire quality grading standards This information indicates the relative performance of passenger car tires in the area of treadwear, traction, and temperature resistance - 2010 Subaru Legacy | Owner's Manual - Page 426
grade assigned to this tire is based on straightahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety - 2010 Subaru Legacy | Owner's Manual - Page 427
Consumer information and Reporting safety defects 13-17 Reporting safety defects , it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or Subaru of America, Inc. To contact NHTSA, you may call the Vehicle Safety Hotline - 2010 Subaru Legacy | Owner's Manual - Page 428
---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- - 2010 Subaru Legacy | Owner's Manual - Page 429
Index 14 - 2010 Subaru Legacy | Owner's Manual - Page 430
XMTM satellite radio reception ...5-2 Auto on/off headlights ...3-27 Sensor ...3-28 Auto-dimming mirror/compass ...3-36 Automatic climate control system...4-8 Automatic transmission ...7-18 Capacities ...12-4 Fluid ...11-24 Manual mode ...7-21 Oil temperature warning light (AT OIL TEMP) ...3-15 - 2010 Subaru Legacy | Owner's Manual - Page 431
14 CHECK ENGINE warning light/Malfunction indicator lamp...3-12 Checking Brake pedal free play ...11-33 Brake pedal reserve distance ...11-33 Clutch function ...11-33 Clutch pedal free play ...11-34 Coolant level...11-18 Fluid level (automatic transmission fluid)...11-24 Fluid level (brake fluid - 2010 Subaru Legacy | Owner's Manual - Page 432
variable transmission...7-18 Capacities ...12-4 Fluid...11-26 Manual mode ...7-21 Oil temperature warning light (AT OIL TEMP) ...3-15 Select lever ...7-19 Shift lock function...7-20 Coolant...11-18 Temperature high warning light ...3-13 Temperature low indicator light...3-13 Cooling system ...11 - 2010 Subaru Legacy | Owner's Manual - Page 433
Flat tires ...9-6 Floor mat ...6-14 Fluid level Automatic transmission ...11-24 Brake ...11-30 Clutch...11-31 Power steering ...11-29 Fog light Bulb ...11-53 Indicator light...3-23 Switch...3-30 Front Differential gear oil...11-26 Fog light ...3-30, 11-53 Fog light indicator light ...3-23 Position - 2010 Subaru Legacy | Owner's Manual - Page 434
Illumination brightness control...3-30 Immobilizer...2-3 Indicator light (security indicator light) ...2-4, 3-22 Indicator light Coolant temperature low ...3-13 Cruise control ...3-23, 7-41 Cruise control set...3-23, 7-41 Door open...3-20 Front fog light ...3-23 Headlight...3-23 High beam...3-23 - 2010 Subaru Legacy | Owner's Manual - Page 435
N New vehicle break-in driving ...8-2 O Odometer ...3-6 Off road driving ...8-6 Oil filter ...11-14 Oil level Engine ...11-12 Front differential gear ...11-26 Manual transmission ...11-23 Rear differential gear ...11-27 Warning light...3-14 Oil pressure warning light ...3-14 Outside Mirror defogger - 2010 Subaru Legacy | Owner's Manual - Page 436
...11-43 Replacing Air cleaner element...11-21 Battery (remote engine start transmitter) ...7-14 Battery (remote keyless entry system)...2-11 Lost transmitters (remote keyless entry system) ...2-12 Replacing bulbs ...11-50 Back-up light (Legacy) ...11-54 Brake light (Outback) ...11-55 Brake/Tail and - 2010 Subaru Legacy | Owner's Manual - Page 437
airbag...1-43 Side airbag ...1-53 SRS airbag (Supplemental Restraint System airbag)...4, 1-38 SRS airbag system Monitors ...1-62 Servicing ...1-63 Warning light...3-11 Starting the engine ...7-8 State emission testing (U.S. only) ...7-6 Steering wheel Power ...7-23 Tilt/telescopic ...3-38 Stopping - 2010 Subaru Legacy | Owner's Manual - Page 438
-floor storage compartment...6-18 V Valet mode ...2-18 Vanity mirror ...6-5, 11-59 Light ...11-59 Vehicle Capacity weight...8-13 Identification ...12-13 Symbols ...3 Vehicle Dynamics Control OFF indicator light ...3-21, 7-31 OFF switch ...7-31 Operation indicator light...3-21, 7-30 System...7-28 - 2010 Subaru Legacy | Owner's Manual - Page 439
W Warning and indicator lights ...3-9 Warning light ABS ...3-16, 7-25 All-Wheel Drive...3-20 AT OIL TEMP ...3-15 Brake system ...3-17 Charge ...3-14 CHECK ENGINE ...3-12 Coolant temperature high ...3-13 Door open...3-20 Engine low oil level ...3-14 Low fuel...3-8, 3-19 Low tire pressure ...3-15 Oil - 2010 Subaru Legacy | Owner's Manual - Page 440
---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- - 2010 Subaru Legacy | Owner's Manual - Page 441
---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- - 2010 Subaru Legacy | Owner's Manual - Page 442
---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- - 2010 Subaru Legacy | Owner's Manual - Page 443
---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- - 2010 Subaru Legacy | Owner's Manual - Page 444
---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- - 2010 Subaru Legacy | Owner's Manual - Page 445
---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- - 2010 Subaru Legacy | Owner's Manual - Page 446
---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- ---------------------------------------- - 2010 Subaru Legacy | Owner's Manual - Page 447
3 13 12 4 11 10 5 9 6 7 8 000134 - 2010 Subaru Legacy | Owner's Manual - Page 448
under severe driving conditions" F11-17 & Fuel octane rating This octane rating is the average of the Research Octane and Motor Octane numbers and is commonly referred to as the Anti Knock Index (AKI). Refer to "Fuel" F7-2 section in this manual. & Engine oil capacity: 2.5 L models: 4.2 US
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
-
313
-
314
-
315
-
316
-
317
-
318
-
319
-
320
-
321
-
322
-
323
-
324
-
325
-
326
-
327
-
328
-
329
-
330
-
331
-
332
-
333
-
334
-
335
-
336
-
337
-
338
-
339
-
340
-
341
-
342
-
343
-
344
-
345
-
346
-
347
-
348
-
349
-
350
-
351
-
352
-
353
-
354
-
355
-
356
-
357
-
358
-
359
-
360
-
361
-
362
-
363
-
364
-
365
-
366
-
367
-
368
-
369
-
370
-
371
-
372
-
373
-
374
-
375
-
376
-
377
-
378
-
379
-
380
-
381
-
382
-
383
-
384
-
385
-
386
-
387
-
388
-
389
-
390
-
391
-
392
-
393
-
394
-
395
-
396
-
397
-
398
-
399
-
400
-
401
-
402
-
403
-
404
-
405
-
406
-
407
-
408
-
409
-
410
-
411
-
412
-
413
-
414
-
415
-
416
-
417
-
418
-
419
-
420
-
421
-
422
-
423
-
424
-
425
-
426
-
427
-
428
-
429
-
430
-
431
-
432
-
433
-
434
-
435
-
436
-
437
-
438
-
439
-
440
-
441
-
442
-
443
-
444
-
445
-
446
-
447
-
448
 |
 |
This manual describes the following types of the Legacy series.
1)
Legacy
2)
Outback