2007 Toyota Sequoia Navigation Manual
2007 Toyota Sequoia Manual
2007 Toyota Sequoia manual content summary:
- 2007 Toyota Sequoia | Navigation Manual - Page 1
06 06.06 BASIC FUNCTIONS SECTION BASIC FUNCTIONS Basic information before operation I Display operation ...2 Touch switch operation ...2 Inputting letters and numbers ...3 Current position display ...5 Screen scroll operation (one−touch scroll) ...5 Map scale ...9 Orientation of the map ...9 - 2007 Toyota Sequoia | Navigation Manual - Page 2
on the screen. To prevent damage to the screen, lightly touch switches on the screen with your finger. When is moving. It could damage your navigation system. You can adjust the angle of the display by pushing the "TILT" button. off, the display will automatically move back to position 0 . The display - 2007 Toyota Sequoia | Navigation Manual - Page 3
06 06.06 BASIC FUNCTIONS INFORMATION D If the system does not respond to a touch of a switch, move your finger away from the screen and then touch it again. D You cannot switches. Inputting letters and numbers When searching for an address or a name, or entering a memo, you can input letters and - 2007 Toyota Sequoia | Navigation Manual - Page 4
page through the list by using the appropriate switch. This expresses a displayed screen position. 1U003a If appears to the right of the item name, the complete name is too long for the display. Touch to scroll to the end of the name. Touch to scroll to the beginning of the name - 2007 Toyota Sequoia | Navigation Manual - Page 5
displayed. D To correct the current position manually, see page 81. 1U004a If you wish to look at a point on the map which is different to your current vehicle position, you can bring the desired point to the center of the screen by using the scroll feature. If you continue to hold your finger - 2007 Toyota Sequoia | Navigation Manual - Page 6
the "MAP/ VOICE" button, the current vehicle position mark returns to the center of the screen and the map moves as you proceed along the designated route. a specific point. INFORMATION When you use the one−touch scroll feature, the current vehicle position mark may disappear from the screen. Move - 2007 Toyota Sequoia | Navigation Manual - Page 7
06 06.06 BASIC FUNCTIONS D To see information about the icon where the cursor is set Touch the "Info." switch. 1U014a 1U016a The registered point is shown by on the map. To change the icon or name, etc., see page 72. You can register up to 106 memory points. If you attempt to register more than - 2007 Toyota Sequoia | Navigation Manual - Page 8
06 06.06 BASIC FUNCTIONS INFORMATION The desired Point of Interest can be displayed on the map screen. (For details, see page 53.) MEMORY POINT INFORMATION When the cursor is set on a memory point icon, the name and "Info." switch are displayed on the top of screen. 1U022a Touch the "Info." - 2007 Toyota Sequoia | Navigation Manual - Page 9
06 06.06 BASIC FUNCTIONS Map scale INFORMATION When the map scale is at the maximum range of 250 miles (400 km), is not shown. When the map scale is at the minimum range of 150 feet (50 m), is not shown. However, in the area where the foot print map is contained, when the map scale is changed to - 2007 Toyota Sequoia | Navigation Manual - Page 10
obstructed, leading to inaccurate vehicle position on the map display. Tunnels, tall buildings, trucks, or even the placement of objects on the instrument panel may obstruct the GPS signals. The GPS satellites may not send signals due to repairs or improvements being made to them. Even when the - 2007 Toyota Sequoia | Navigation Manual - Page 11
on a long straight road. When freeway and surface streets run in parallel. After moving by ferry or vehicle carrier. When a turntable in the parking lot. When leaving a covered parking lot or parking garage. When a roof carrier manually. For information on setting the current position calibration, see - 2007 Toyota Sequoia | Navigation Manual - Page 12
of the vehicle that vary by time or season or other reasons. D The road and map data stored in your navigation system may not be complete or may not be the latest version. After replacing the tire, implement the operation described in the "D Tire change calibration". (For details, see page 82 - 2007 Toyota Sequoia | Navigation Manual - Page 13
not extract or re−utilize any portion of the contents of the DATABASE, nor reproduce, copy, modify, adapt, translate, disassemble, decompile, or reverse engineer any portion of the DATABASE. TRANSFER You may not transfer the DATABASE to third parties, except together with the system for which it was - 2007 Toyota Sequoia | Navigation Manual - Page 14
; road slope or grade; bridge height, weight or other limits; road or traffic ("POI" Data) in the navigation system is in part provided by infoUSA Inc. ("infoUSA"). By using the copy, modify, adapt, translate, disassemble, decompile, or reverse engineer any portion of the POI Data. 3. Transfer You may - 2007 Toyota Sequoia | Navigation Manual - Page 15
service bureau, time−sharing or other similar purposes. You may not modify the information or remove any copyright notices that appear on the information in any way. You may not decompile, disassemble or reverse engineer content, quality, accuracy, completeness, effectiveness, reliability, - 2007 Toyota Sequoia | Navigation Manual - Page 16
06 06.06 BASIC FUNCTIONS Disclaimer of Liability: DENSO SHALL NOT BE LIABLE TO YOU FOR ANY CLAIM, DEMAND OR ACTION, IRRESPECTIVE OF ITS NATURE, ALLEGING ANY LOSS, INJURY OR DAMAGES, WHETHER DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, INCLUDING ANY LOSS OF PROFIT, REVENUE OR - 2007 Toyota Sequoia | Navigation Manual - Page 17
were licensed, and not for service bureau, time−sharing or other save it, provided that you do not remove any copyright notices that appear and do not modify, decompile, disassemble or reverse engineer any portion of this Data, and , quality, accuracy, completeness, effectiveness, reliability, fitness - 2007 Toyota Sequoia | Navigation Manual - Page 18
to you. Export Control. You agree not to export from anywhere any part of the Data provided to you or any direct product thereof except in provisions, or (ii) the United Nations Convention for Contracts for the International Sale of Goods, which is explicitly excluded. You agree to submit to the - 2007 Toyota Sequoia | Navigation Manual - Page 19
forth in the following "Limited Rights Notice" at FAR 52.227−14(g)(2) (Alternate II), which shall be affixed to the Licensed Data and the Licensed Data shall shall be marked on any reproduction of these data, in whole or in part): LIMITED RIGHTS NOTICE (JUN 1987) These data may be reproduced and - 2007 Toyota Sequoia | Navigation Manual - Page 20
one type of area, primarily around metropolitan centers, detailed route guidance is available for the right turns, one−way traffic, etc.) is not complete. It is still possible to reach the destination by pricing of an update. 2. Touch the "Map DVD" switch. 1U008c Make sure the version of the - 2007 Toyota Sequoia | Navigation Manual - Page 21
To display the disc coverage area, touch the "Covered Area" switch. Confirm the covered area on the screen. Contact your dealer to find be thrown about in the compartment and possibly injure people in the vehicle during sudden braking or in an accident. D To reduce the chance of injury in the case - 2007 Toyota Sequoia | Navigation Manual - Page 22
06 06.06 BASIC FUNCTIONS 22 - 2007 Toyota Sequoia | Navigation Manual - Page 23
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE SECTION Basic functions in frequent use II 24 24 26 26 26 30 33 36 37 38 38 39 40 41 41 42 42 44 44 46 48 53 55 56 57 61 62 DESTINATION INPUT AND ROUTE GUIDANCE Destination input ...Selecting the search area ...Destination input by Home ... - 2007 Toyota Sequoia | Navigation Manual - Page 24
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE Destination input - Push the "DEST" button and the "Destination" screen appears. D Route guidance may not be available if there is no road data for the specified location. D When setting the destination on a map with a scale larger than 0.5 mile (800 - 2007 Toyota Sequoia | Navigation Manual - Page 25
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE U.S.A. Switch "US1" "US2" States included in the search area Idaho Oregon Washington California Nevada Arizona Colorado Montana New Mexico Utah Wyoming Iowa Kansas Minnesota Missouri North Dakota Nebraska South Dakota Oklahoma Texas Illinois Indiana - 2007 Toyota Sequoia | Navigation Manual - Page 26
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE - Destination input by Home - Destination input by Quick access - Destination input by "Address" There are 2 ways to input a destination by address. Touch the "Address" switch on the "Destination" screen. 2U003b Touch the home switch on the " - 2007 Toyota Sequoia | Navigation Manual - Page 27
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE (a) Inputting a house number and a street name It is possible to input a street name first. Touch the "Street" switch to display the screen for inputting a street name. 2U008a 2U006c Touch numerals directly on the screen to input a house number. - 2007 Toyota Sequoia | Navigation Manual - Page 28
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE (b) Selecting a city to search Touch the "City" switch. 2U009a Select or enter your desired city. "Input Name": To narrow down the listed items by inputting the city name. 2U010c 2U012a If you input a street name first, the screen changes. You can - 2007 Toyota Sequoia | Navigation Manual - Page 29
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE SELECTING FROM THE LAST 5 CITIES SELECTING FROM THE NEAREST 5 CITIES Touch the "Nearest 5 Cities" switch. INPUTTING THE CITY NAME Touch the "Input City Name" switch. 2U120b 2U013a Touch the switch of the desired city name. If you have not used the - 2007 Toyota Sequoia | Navigation Manual - Page 30
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE - Destination input by "POI Name" 2U015a Touch the switch of the desired city name from the displayed list. "Map": To display the selected destination and the route preference. (See " - Entering destination" on page 42.) The current screen changes to - 2007 Toyota Sequoia | Navigation Manual - Page 31
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE (a) Selecting a city to search Touch the "City" switch. SELECTING FROM THE LAST 5 CITIES 2U018a 2U019a Touch the switch of the desired destination. "Dist. Sort": In the order of distance from your current position. The distance from your current - 2007 Toyota Sequoia | Navigation Manual - Page 32
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE SELECTING FROM THE NEAREST 5 CITIES Touch the "Nearest 5 Cities" switch. INPUTTING THE CITY NAME Touch the "Input City Name" switch. 2U022a 2U020c Touch the switch of the desired city name. 2U021a Touch the switch of the desired city name from the - 2007 Toyota Sequoia | Navigation Manual - Page 33
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE (b) Selecting from the categories Touch the - Destination input by "POI Category" "Category" switch. 2U024a 2U023a When you touch the desired category, the POI name list screen appears. The destination can be set by selecting the POI category and - 2007 Toyota Sequoia | Navigation Manual - Page 34
the category displayed by the icon, touch the "List" switch. To set search points, the following four methods are possible. 1. Inputting city center 2. Setting the current position as the search point 3. Setting the search point via the map screen 4. Setting the search point from the destinations - 2007 Toyota Sequoia | Navigation Manual - Page 35
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE SETTING THE CURRENT POSITION AS THE SEARCH POINT Touch the "Current Position" switch. SETTING THE SEARCH POINT VIA THE MAP SCREEN Touch the "Map" switch. 2U030a 2U031a When you touch an arrow facing the desired point, the map scrolls in that - 2007 Toyota Sequoia | Navigation Manual - Page 36
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE SETTING THE SEARCH POINT FROM THE DESTINATIONS Touch the destination switches at the bottom of the screen. (c) Selecting from a list You can select the desired destination from the listed POI names. - Destination input by "Emergency" By touching the - 2007 Toyota Sequoia | Navigation Manual - Page 37
. "Name": To list the memory points in alphabetical order. "Attribute": To list the memory points by the registered attribute. INFORMATION The navigation system does not guide in areas where route guidance is unavailable. (See page 12.) 37 - 2007 Toyota Sequoia | Navigation Manual - Page 38
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE - Destination input by "Previous" Touch the "Previous" switch on the "Destination" screen. INFORMATION You can delete the list of previous destinations while your vehicle is stopped, if you no longer need them. (See page 95.) - Destination input by " - 2007 Toyota Sequoia | Navigation Manual - Page 39
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE - Destination input by "Intersection" Touch the "Intersection" switch on the "Destination" screen. 2U040a Touch the switch of the desired item. After inputting the two intersecting streets, the screen changes and displays the map location of the - 2007 Toyota Sequoia | Navigation Manual - Page 40
order by name. "Input Name": An applicable list is displayed by touching this switch and inputting name. 2U041a Be sure to use the complete name of the freeway or highway, including the hyphen, when entering the destination. Freeways and interstates use an "I" (I−405). US highways use the - 2007 Toyota Sequoia | Navigation Manual - Page 41
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE - Destination input by "Coordinates" Touch the "Coordinates" switch on the "Destination" screen. - Destination input by "Phone #" Touch the "Phone "Destination" screen. #" switch on the 2U047b 2U045a Input the latitude and the longitude. When the - 2007 Toyota Sequoia | Navigation Manual - Page 42
switch to see name, address, and phone number, etc. INFORMATION D Guidance can be suspended or resumed. (See page 66.) D If you keep touching the "Guide" switch until a beep sounds, Demo mode will start. 2U048b SCREEN A 1. When you touch an arrow facing the desired point, the map scrolls in that - 2007 Toyota Sequoia | Navigation Manual - Page 43
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE D To change the route before starting guidance ROUTE PREFERENCE You can change route preference by touching the "Change" switch on SCREEN A. INFORMATION D Even if the "Allow Freeway" indicator is dimmed, the route cannot avoid including a freeway in - 2007 Toyota Sequoia | Navigation Manual - Page 44
name will be displayed at the bottom of the screen. In some areas, the roads have not been completely digitized in our database yet. For this reason, the route guidance may guide the road that is not allowed to pass. The voice guidance provides various messages as you approach an intersection - 2007 Toyota Sequoia | Navigation Manual - Page 45
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE INFORMATION On freeways, interstates or other highways with higher speed limits, the voice guidance will be made at earlier points than on city streets in order to allow time to maneuver. 4.2 miles 0.25 miles One−way road 2U116a 2U117a One−way road - 2007 Toyota Sequoia | Navigation Manual - Page 46
may be made early or delayed. D If you did not hear the voice guidance command, touch the "MAP/ VOICE" button to hear it again. D To adjust the voice guidance volume, see page 67. "In half of a mile, make a legal U− turn." "Make a legal U−turn ahead." (Beep sound only) Setting and deleting - 2007 Toyota Sequoia | Navigation Manual - Page 47
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE 3. Input an additional destination in the same way as the destination input. (See page 24.) (b) Reordering destinations When more than one destination is set, you can change the arrival order of the destinations. 1. Touch the "Route" switch. 2U057a - 2007 Toyota Sequoia | Navigation Manual - Page 48
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE (c) Deleting destination You can delete a set destination. 1. Touch the "Route" switch. 2U058a 2. Touch the "Destination". "Delete All": To delete all destinations on the list. 4. A message appears to confirm your request to delete. To delete the - 2007 Toyota Sequoia | Navigation Manual - Page 49
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE (b) Deleting preferred road You can delete a set preferred road. 1. Touch the "Route" switch. 2U062a 3. Select the preferred road which you wish to modify and touch the "Enter z" switch. 4. A message appears to confirm your request. To add the - 2007 Toyota Sequoia | Navigation Manual - Page 50
" switch. 2U066a 2. Touch the "Search Condition" switch. The "Search Condition" screen appears. 2U068b The entire route from the starting point to the destination is displayed. "Guide": To start guidance. "Route": To add or change a route. (For details, see pages 46 and 48.) 50 - 2007 Toyota Sequoia | Navigation Manual - Page 51
an entire new route to the destination. 2U119a 2U069a 2. Touch the "Detour" switch. This picture shows an example of how the system would guide you around a delay caused by a traffic jam. 1 This position indicates the location of a traffic jam caused by road repairs or an accident. 2 This - 2007 Toyota Sequoia | Navigation Manual - Page 52
. After choosing the conditions, touch the "OK" switch. You can start the route guidance from the adjacent road. (ex. When the route guidance guides the route on the freeway, but you drive on the parallel way along a freeway.) 1. Touch the "Route" switch. 2U071a 2. Touch the "Route Preference - 2007 Toyota Sequoia | Navigation Manual - Page 53
Off" switch. "More": If you cannot find your desired Point of Interest on the limited choice screen, touch this switch. The screen then displays the complete POI listing screen. You can display up to 5 categories of icons on the screen. View" switch. 2U076a 53 - 2007 Toyota Sequoia | Navigation Manual - Page 54
you select a Point of Interest type from either the limited list or the complete list, the screen will display symbols at those locations on the map screen. to set as a destination. The map will shift so that the icon is centered on the screen and overlaps with the cursor . At this time, the - 2007 Toyota Sequoia | Navigation Manual - Page 55
The entire route from the current position to the destination is displayed. "Guide": To start guidance. "Route": To change the route. (For details, road changes its name without requiring a turn (such as on a street that runs through two or more cities), the name change will not appear on the list. - 2007 Toyota Sequoia | Navigation Manual - Page 56
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE Touch the "Map" switch of your desired point. The point which you choose is displayed on the map screen. Route preview 2U084a 2U085a 1. Touch the "Map 2U087a : To indicate the next destination. View" switch. : To preview the route to the next - 2007 Toyota Sequoia | Navigation Manual - Page 57
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE Screen configuration You can choose any one of the screen configurations. Depending on the conditions, it may not be possible to select certain screen configuration switches. : To display single map screen. (See page 57.) : To display dual map screen. - 2007 Toyota Sequoia | Navigation Manual - Page 58
the following procedures. D Changing the map scale D Displaying the POI icon D Changing the orientation of the map Touch the "OK" switch when you complete editing. The screen returns to the dual map screen. 2U094a Information about the destination and current position, as well as a compass, is - 2007 Toyota Sequoia | Navigation Manual - Page 59
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE (d) Turn list screen (e) Arrow screen (f) Freeway information screen 2U095a The screen shows the turn list. You cannot scroll through the list of roads. 2U096a The screen shows the current road name and the distance to the next corner. 2U097b This - 2007 Toyota Sequoia | Navigation Manual - Page 60
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE INFORMATION When you drive on a freeway, the screen is automatically divided into two parts, with freeway information screen on the right side. (g) Intersection guidance screen/guidance screen on freeway D Intersection guidance screen This screen - 2007 Toyota Sequoia | Navigation Manual - Page 61
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE Distance and time to destination INFORMATION 2U103a 2U102b When the vehicle is on the guidance route, the distance and the estimated travel time to the destination are displayed. When the vehicle is not on the guidance route, the distance to and the - 2007 Toyota Sequoia | Navigation Manual - Page 62
AND ROUTE GUIDANCE Foot print map For the area which is covered by the foot print map (Some areas in the following cities INFORMATION D If the map or the current position is moved to the area which is not covered by the foot print map, the screen scale automatically changes to 150 feet (50 m). D - 2007 Toyota Sequoia | Navigation Manual - Page 63
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE 2U110a 2. Using an eight−direction arrow, move the cursor to the position of the building you wish to display information. 3. Touch the "Building Info." switch. 2U111a 4. Details of POIs in some buildings may be displayed. If you wish to see detailed - 2007 Toyota Sequoia | Navigation Manual - Page 64
06 06.06 DESTINATION INPUT AND ROUTE GUIDANCE 64 - 2007 Toyota Sequoia | Navigation Manual - Page 65
Setup ...Current position calibration ...Distance unit ...Estimated travel time ...Auto reroute ...Adjusting time zone ...Auto voice guidance ...Voice guidance in all modes ...Notifying function ...POI category change (Show POI Icons) ...Delete previous point ...Map color ...Screen animation ... 65 - 2007 Toyota Sequoia | Navigation Manual - Page 66
06 06.06 ADVANCED FUNCTIONS Suspending and resuming guidance D To suspend guidance You can suspend route guidance. D To resume guidance You can resume the suspended route guidance. 3U002c 3U003c The screen will return to the current position map without route guidance. Push the "MENU" button to - 2007 Toyota Sequoia | Navigation Manual - Page 67
The system can memorize the following settings for up to three users. D Map direction D Map scale D Guidance mode D Setup D Volume D Language 3U006a To adjust the volume, select the desired level by touching the appropriate number. If you do not need voice guidance, touch the "Off" switch. The - 2007 Toyota Sequoia | Navigation Manual - Page 68
". 3U009b The confirmation screen will appear. To register, touch the "Yes" switch. To return to the previous screen, touch the "No" or "Back" switch. 3U010b When you touch the switch already registered, this screen appears. To replace, touch the "Yes" switch. To cancel the replacement, touch - 2007 Toyota Sequoia | Navigation Manual - Page 69
06 06.06 ADVANCED FUNCTIONS D To change user D To delete user 3U011c Push the "MENU" button to display the "Menu" screen. Then touch the "Select User" switch. 3U012b Touch the "User wish to change. 3U014b Touch the "Delete" switch of "User number" you wish to delete. number" switch you - 2007 Toyota Sequoia | Navigation Manual - Page 70
a destination. (a) Registering memory points 3U015b The confirmation screen appears. To delete, touch the "Yes" switch. To return to the previous screen, touch the "No" or "Back" switch. 3U016c 1. Push the "MENU" button to display the "Menu" screen and touch the "My Places" switch. 70 - 2007 Toyota Sequoia | Navigation Manual - Page 71
06 06.06 ADVANCED FUNCTIONS 3U017b 2. Touch the "Register" switch of the "Memory Points". 3U018b A screen similar to the destination input screen appears. Input the desired point in the same way as inputting a destination. (See page 24.) When you finish memory point registration, the memory point - 2007 Toyota Sequoia | Navigation Manual - Page 72
06 06.06 ADVANCED FUNCTIONS (b) Editing memory points The icon, attribute, name, location and/or telephone number of a registered memory point can be edited. 1. Push the "MENU" button to display the "Menu" screen and touch the "My Places" switch. 3U021a The screen lists the memory points. "Date": - 2007 Toyota Sequoia | Navigation Manual - Page 73
. 3U024a Touch the desired sound icon. The next screen appears when you touch the "Bell (with direction)" switch. 3U100a Touch the direction switches and adjust the direction. Touch the "Enter" switch. The bell sounds only when your vehicle approaches this point in the direction that you set. 73 - 2007 Toyota Sequoia | Navigation Manual - Page 74
or Quick access 1 to 5. 3U026b 3U025b To replace the attribute, touch the "Yes" switch. To return to the previous screen, touch the "No" or "Back" switch. Touch the desired attribute. It is possible to replace a registered attribute. 3U027c To delete the attribute, touch the switch. "Del." 74 - 2007 Toyota Sequoia | Navigation Manual - Page 75
To delete an attribute, touch the "Yes" switch. To return to the previous screen, touch the "No" or "Back" switch. 3U029a Touch the alphabet and/or numeral keys. When the entry has been completed, touch the "OK" switch on the screen. The previous screen will be displayed. D "Show Name" You can set - 2007 Toyota Sequoia | Navigation Manual - Page 76
" switch. To delete, touch the "Yes" switch. To cancel the deletion, touch the "No" switch. 3U031a 3U032b Touch numeral keys. When the entry has been completed, touch the "OK" switch on the screen. The previous screen will be displayed. 2. Touch the "Delete" switch of the "Memory Points". 76 - 2007 Toyota Sequoia | Navigation Manual - Page 77
switch of the "Areas to avoid". 3U039a 3U038b 3. Set the cursor in the center of the area to avoid, and touch the "Enter" switch. 2. Enter the inputted in the area to avoid or the route calculation cannot be made without running through the area to avoid, a route passing through the area to avoid - 2007 Toyota Sequoia | Navigation Manual - Page 78
of the "Areas to Avoid" to display the "Edit Area to Avoid" screen. 3U040a 3U042a 3. Touch the "Name" , "Location" or "Area Size" switch on this screen. 3U041a 4. Touch either or switch to change the size of the area to avoid. 2. To edit an area to avoid, touch the corresponding switch. 78 - 2007 Toyota Sequoia | Navigation Manual - Page 79
06 06.06 ADVANCED FUNCTIONS D To change "Name" D To change "Location" D To change "Area size" 3U043a Touch alphabet or numeral keys. When the entry has been completed, touch the "OK" switch on the screen. The previous screen will be displayed. D "Show Name" The avoid area name can be set to be - 2007 Toyota Sequoia | Navigation Manual - Page 80
screen and then the previous screen will be displayed. "Default": This switch initializes all of the settings. "Calibration": You can adjust the current vehicle position mark manually. "Distance": You can select "km" or "miles" as the distance unit. "Estimated Travel Time": You can set the system to - 2007 Toyota Sequoia | Navigation Manual - Page 81
the desired map color. "Screen Animation": You can set some screen displays to be animated. Current position calibration When driving, the current vehicle position mark will be automatically corrected by GPS signals. If GPS reception is poor due to location, you can manually adjust the current - 2007 Toyota Sequoia | Navigation Manual - Page 82
map screen will be displayed. D Tire change calibration The tire change calibration function will be used when replacing the tires. This function will adjust the mis−calculation caused by the circumference difference between the old tires and new ones. If this procedure is not performed when tires - 2007 Toyota Sequoia | Navigation Manual - Page 83
06 06.06 ADVANCED FUNCTIONS Distance unit 1. Push the "MENU" button. Estimated travel time You can set the speed that is used for the calculation of the estimated travel time. 3U055b 3U054c 2. Touch the "Setup" switch. 3. Touch the "km" or "miles" switch of "Distance" to choose the distance unit - 2007 Toyota Sequoia | Navigation Manual - Page 84
06 06.06 ADVANCED FUNCTIONS INFORMATION 3U057c 2. Touch the "Setup" switch. 3U059a D The displayed time to the destination is the approximate driving time that is calculated based on the speeds you selected and your actual position along the guidance route. D The time shown on the screen may - 2007 Toyota Sequoia | Navigation Manual - Page 85
route. This feature does not operate while you are driving on roads where guidance is not available. To turn the "Auto Reroute" mode on: 1. Push the "MENU" button. Adjusting time zone 1. or may not take you back to the previous route depending on how far you are off the original guidance route. 85 - 2007 Toyota Sequoia | Navigation Manual - Page 86
automatically. When the "Auto Voice Guidance" feature is turned off, the voice guidance can be heard only if you push the "MAP/ VOICE" button. To turn the "Auto Voice Guidance" mode on: 1. Push the "MENU" button. 3U063b 3. Touch the "Change" switch. The "Adjust Time Zone" screen appears on the - 2007 Toyota Sequoia | Navigation Manual - Page 87
turned on, you can hear the voice guidance in all modes. When the "Voice Guidance in All Modes" feature is turned off, voice guidance cannot be heard when using the audio system. To turn the "Voice Guidance in All Modes" on: 1. Push the "MENU" - 2007 Toyota Sequoia | Navigation Manual - Page 88
06 06.06 ADVANCED FUNCTIONS Notifying traffic restriction When the "Notify Traffic Restriction" feature is turned on, the system notifies you of traffic or seasonal restrictions. 1. Push the "MENU" button. 3U068a 3. Touch the "On" switch of "Voice Guidance in - 2007 Toyota Sequoia | Navigation Manual - Page 89
06 06.06 ADVANCED FUNCTIONS Intersection guidance When the "Intersection Guidance" feature is turned on, the system will display the intersection guidance screen if you drive with route guidance. 3U071a 3. Touch the "On" switch of "Notify Traffic - 2007 Toyota Sequoia | Navigation Manual - Page 90
06 06.06 ADVANCED FUNCTIONS Guidance screen on freeway When the "Guidance Screen on Freeway" feature is turned on, the system will display the lane guidance screen if you drive on a freeway with route guidance. 3U074a 3. Touch the "On" switch of " - 2007 Toyota Sequoia | Navigation Manual - Page 91
06 06.06 ADVANCED FUNCTIONS Street name on scroll map When the "Street Name on Scroll Map" feature is turned on, the system will display the name of a street where the cursor is positioned on the scroll map. 3U077a 3. Touch the "On" switch - 2007 Toyota Sequoia | Navigation Manual - Page 92
06 06.06 ADVANCED FUNCTIONS Display of building shape When the "Display Building Shape" feature is turned on, the system will display the building shape on the map screen using a scale of 150 feet (50 m) to 300 feet (100 m). 3U080b 3. - 2007 Toyota Sequoia | Navigation Manual - Page 93
06 06.06 ADVANCED FUNCTIONS Screen layout function Function) ( 3U083c 3. Touch the "On" switch of "Display Building Shape" and touch the "OK" switch. You can set display or hide each switch and current street name on the map screen. 1. Push the "MENU" button. 3U085c 3. Touch the "Change" switch - 2007 Toyota Sequoia | Navigation Manual - Page 94
06 06.06 ADVANCED FUNCTIONS POI category change (Show POI Icons) You can choose 6 icons displayed on the "Show POI Icons" top screen, so that you can easily set which icons to display on the map screen. 3U088c 2. Touch the 3U089c Then 3. Touch the "Change" switch of "Show POI Icons". 3U087a 1. - 2007 Toyota Sequoia | Navigation Manual - Page 95
06 06.06 ADVANCED FUNCTIONS Delete previous point You can delete your previous destination. 1. Push the "MENU" button. 3U091a 3U092c 5. Touch the switch corresponding to the desired category. Then touch the "OK" switch. 2. Touch the "Setup" switch. Then touch switch twice to display page 3 of the - 2007 Toyota Sequoia | Navigation Manual - Page 96
06 06.06 ADVANCED FUNCTIONS Map color 1. Push the "MENU" button. 3U094b 4. Touch the switch you want to delete. For efficient previous point search, previous points can be sorted by the "Date" - 2007 Toyota Sequoia | Navigation Manual - Page 97
FUNCTIONS Screen animation When the "Screen Animation" feature is turned on, some switches and screens become animated. (e.g.: change map guidance on the map screen) To turn the "Screen Animation" mode on: 1. Push the "MENU" button. 3U097a 3. Touch the desired color for day and/or night map and - 2007 Toyota Sequoia | Navigation Manual - Page 98
06 06.06 ADVANCED FUNCTIONS 98 - 2007 Toyota Sequoia | Navigation Manual - Page 99
06 06.06 OTHER FUNCTIONS SECTION OTHER FUNCTIONS Other functions IV 100 105 112 114 Maintenance information ...Calendar with memo ...Screen adjustment ...Screen setting ... 99 - 2007 Toyota Sequoia | Navigation Manual - Page 100
06 06.06 OTHER FUNCTIONS Maintenance information RS01015 This system informs you when to replace certain parts or components and shows dealer information (if registered) on the screen. (See "Information items" on page 101.) When the navigation system begins operating after either - 2007 Toyota Sequoia | Navigation Manual - Page 101
vehicle needs to be serviced, the icon color will change to orange. Information items Oil change Replace oil filter INFORMATION D For scheduled maintenance information, please refer to the "Scheduled Maintenance Guide", "Warranty and Services Guide" or "Owner's Manual Supplement". D Depending on - 2007 Toyota Sequoia | Navigation Manual - Page 102
, location and phone number. Replace brake fluid 4U006b 4U005a 2. Enter the location of the dealer in the same way as for destination input. (See page 24.) 1. Touch the "Set Dealer" switch on the "Maintenance" screen. Replace ATF Scheduled maintenance Replace air filter Personal event 102 - 2007 Toyota Sequoia | Navigation Manual - Page 103
06 06.06 OTHER FUNCTIONS (b) Edit dealer 4U007a_toyota After you input the dealer, the screen changes and displays the map location of the dealer. If it is OK, touch the "Enter" switch. The screen changes to "Edit Dealer" screen. (See "(b) Edit dealer".) 4U008a You can edit the dealer name, - 2007 Toyota Sequoia | Navigation Manual - Page 104
06 06.06 OTHER FUNCTIONS D To edit "Dealer" or "Contact" D To edit "Location" D To edit "Phone #" (telephone number) 4U010a To input the name, touch the alphabet, numeral and/or umlaut keys. You can input up to 24 letters. After inputting, touch the "OK" switch at the bottom right of the screen - 2007 Toyota Sequoia | Navigation Manual - Page 105
" switch on the screen. 2. A message will appear on the screen. To delete, touch the "Yes" switch. To cancel the deletion, touch the "No" or "Back" switch. 4U014c Touch the "Enter " switch on the "Set Dealer" screen. The screen changes and displays the map location of the registered dealer and the - 2007 Toyota Sequoia | Navigation Manual - Page 106
06 06.06 OTHER FUNCTIONS (a) Inputting a memo 4U016b To display the "Information Menu" screen, push the "INFO" button. Then touch the "Calendar" switch. 4U017a The current date is circled in yellow. If the current date is not displayed on the screen, touch the "Today" switch to display the - 2007 Toyota Sequoia | Navigation Manual - Page 107
06 06.06 OTHER FUNCTIONS D Memo D Location 4U020a Touch the "Memo" switch to enter text. 4U021a Enter text using the keys. You can enter text up to 24 letters. After entering the text, touch the "OK" switch at the bottom right of the screen. 4U022a Touch the "Location" switch to set location. - 2007 Toyota Sequoia | Navigation Manual - Page 108
06 06.06 OTHER FUNCTIONS D Mark color D Date color 4U023a_date The date inputted is marked as shown above. You can choose the desired mark and/or date color. 4U024a Touch the "Mark" switch. 4U026a Touch the "Date" switch. 4U025a Touch your desired color for the mark. 108 - 2007 Toyota Sequoia | Navigation Manual - Page 109
mark and/or date for the date you added the memo and/or location. To default the date color, touch the "Delete" switch on the screen. After you choose the date and/or mark color, touch the "OK" switch to display the previous screen. 4U028a To add a memo, touch the corresponding date - 2007 Toyota Sequoia | Navigation Manual - Page 110
06 06.06 OTHER FUNCTIONS (d) Editing a memo (e) Memo list 4U030a To edit a memo, touch the corresponding date, and then touch the memo you wish to edit. 4U031a Touch the switch. 4U032a 1. To list the memos you added, touch the "List" switch. "Memo" or "Location" 110 - 2007 Toyota Sequoia | Navigation Manual - Page 111
06 06.06 OTHER FUNCTIONS 4U033c 2. Touch the desired search condition to list the memos. The "Memo list" is displayed on the screen. 4U034a To display the memos listed in a desired period, touch the "Period" switch. Touch the number keys. After setting the period, touch the "OK" switch. The "Memo - 2007 Toyota Sequoia | Navigation Manual - Page 112
contrast of the screen can be adjusted depending on the brightness of your surroundings. You can also turn the display off. To display the "Display" screen push the "DISPLAY" button. The screen goes off when you touch the "SCREEN OFF" switch. To turn the display screen back on, push any button such - 2007 Toyota Sequoia | Navigation Manual - Page 113
off when you touch "SCREEN OFF". To turn the screen back on, push any button such as "INFO", etc. The selected screen appears. 4U319a Color and tone adjustment (with rear seat entertainment system) You can adjust the color and the tone while the DVD video, DVD audio and video CD are being played - 2007 Toyota Sequoia | Navigation Manual - Page 114
Automatic transition You can select a function that enables automatic return to the navigation screen from the audio screen. (b) Background color You can select a background color. 4U303a 2. Touch the "Screen 4U305a 4U304a Setting" switch. Select "ON" or "OFF" and then touch the "OK" switch. "ON - 2007 Toyota Sequoia | Navigation Manual - Page 115
06 06.06 AUDIO SYSTEM SECTION AUDIO SYSTEM Audio system V Quick reference ...116 Using your audio system ...117 Audio system operating hints ...144 V 115 - 2007 Toyota Sequoia | Navigation Manual - Page 116
Push this button to choose an FM station. For details, see pages 118 and 120. "DISC" button Push this button to turn the compact disc player and DVD player on. For details, see pages 118, 125 and 129. "SCAN" button Push this button to scan radio stations or the tracks on discs. For - 2007 Toyota Sequoia | Navigation Manual - Page 117
5U009b NOTICE To prevent the battery from being discharged, do not leave the audio system on longer than necessary when the engine is not running. (a) Turning the system on and off "PWR·VOL": Push this knob to turn the audio system on and off. Turn this knob to adjust the volume. The system turns - 2007 Toyota Sequoia | Navigation Manual - Page 118
SYSTEM 5U167 5U001a 5U121a The switches for radio, compact disc player and DVD player (with rear seat entertainment system) operation are displayed on the function switch display screen when the audio control mode is selected. Touch them lightly and directly on the screen. The selected switch is - 2007 Toyota Sequoia | Navigation Manual - Page 119
from track 1 through to the end of the disc. Then it will play from track 1 again. NOTICE Never try to disassemble or oil any part of the compact disc player. Do not insert anything other than compact discs into the slot. The player is intended for use with 12 cm (4.7 in.) discs only. V 119 - 2007 Toyota Sequoia | Navigation Manual - Page 120
06 06.06 AUDIO SYSTEM (d) Your DVD player (with rear seat entertainment system) You can enjoy the sound of the rear seat entertainment system by pushing the "DISC" button. - Radio operation 5U165 5U166 (a) Listening to the radio Push these buttons to choose either an AM or FM - 2007 Toyota Sequoia | Navigation Manual - Page 121
station memory is cancelled when the power source is interrupted by battery disconnection or a blown fuse. (c) Selecting a station Tune in the desired station using one - search for a stronger signal station. RDS features are available for use only on FM stations which broadcast RDS information. V - 2007 Toyota Sequoia | Navigation Manual - Page 122
as follows: D ROCK D MISC (Miscellaneous) D Inform (Information) D Easy Lis (Easy listening) D Cls/Jazz (Classical music and Jazz) D R & B (Rhythm and Blues) D Religion D Alert (Emergency message) 5U091c "TYPE SEEK" switch When a program is set, "TYPE SEEK" switch appears. Touch the switch and the - 2007 Toyota Sequoia | Navigation Manual - Page 123
. Put the compact disc in the slot with the label side up. The player will automatically start when you insert the compact disc. At this time, "CD about in the compartment and possibly injure people in the vehicle during sudden braking or in an accident. D To reduce the chance of injury in case - 2007 Toyota Sequoia | Navigation Manual - Page 124
06 06.06 AUDIO SYSTEM NOTICE Do not obstruct the display while it is moving. It could damage your audio system. To stop and eject the compact disc, push the "OPEN" button to lower the display. Push the " button. "DISC INFORMATION Under extremely cold conditions, the display may react slowly or - 2007 Toyota Sequoia | Navigation Manual - Page 125
appears on the screen. Vehicles with rear entertainment system - If the DVD player is turned on, push the "DISC" button again to switch to the compact disc player. If the rear seat entertainment system is on, pushing the "DISC" button switches the sound of the front audio system and that of the rear - 2007 Toyota Sequoia | Navigation Manual - Page 126
the player will automatically go back to trouble. Push the "DISC" button once again. If the player does not operate, check that the disc surface is not soiled or damaged. If the disc is O.K., the temperature of the player's internal mechanism may be raised because of high external temperature. Remove - 2007 Toyota Sequoia | Navigation Manual - Page 127
only when a disc is loaded in the DVD player. Refer to "Rear seat entertainment system" for details. For appropriate discs for this player, see "Audio system operating hints" on page 144. (a) Inserting the disc 1. Pull up the console box lid while pushing the lock release button. 5U101a V 127 - 2007 Toyota Sequoia | Navigation Manual - Page 128
" appears on the screen. If a disc which is not playable is inserted, "DISC CHECK" will also appear on the screen. For appropriate discs for this player, see "Audio system operating hints" on page 144. An adapter must be used for 8 cm (3 in.) discs which are loaded in the same manner as - 2007 Toyota Sequoia | Navigation Manual - Page 129
while the disc is loaded. NOTICE Never try to disassemble or oil any part of the DVD player. Do not insert anything other than a disc into the slot. 5. Close the console box. (b) Ejecting a disc Slide the lid backward to open the DVD player. Push the disc eject button to eject a disc. CAUTION To - 2007 Toyota Sequoia | Navigation Manual - Page 130
switch on the screen or push the "SCAN" button a second time. If the player reaches the end of the disc, it will continue scanning at track 1. After all track number appears on the display. As you release the button, the player will start playing the selected track from the beginning. switch and Fast - 2007 Toyota Sequoia | Navigation Manual - Page 131
not work properly. Be sure to read the instruction manual for the DVD video disc separately provided. For the detailed information about DVD video discs, see "(h) DVD player and DVD video disc information". Precautions on DVD video disc When recording with a DVD video or video CD, audio tracks may - 2007 Toyota Sequoia | Navigation Manual - Page 132
screen is first displayed after you turn the ignition key to "ACC" or "ON". Touch "OK" when you read the message. 5U121a DVD video 5U122a 5U123a 5U142a DVD video DVD audio PLAYING A DVD DISC Push the "AUDIO" button to display this screen. It you touch the "PICTURE" switch when the vehicle is - 2007 Toyota Sequoia | Navigation Manual - Page 133
the above controls, the menu screen for DVD video appears. (For the operation, see the manual that come with the DVD video disc provided separately.) ": The menu DISPLAYING DVD CONTROLS If you touch a part of the screen, where controls are not located while you are watching video, DVD controls - 2007 Toyota Sequoia | Navigation Manual - Page 134
"Enter". The player starts playing video for that menu item. (For details, see the manual that comes with the DVD video disc provided separately Back", the previous screen returns. 5U127a DVD video SEARCHING BY TITLE Enter the title number using "−", "+" and "+10" and touch "Enter". The player - 2007 Toyota Sequoia | Navigation Manual - Page 135
the screen. The player starts playing the disc from the selected bonus group number. 5U130a CHANGING THE STILL PICTURE DVD audio only - player starts playing the disc from the entered group number. When you push either side of the "SEEK/ TRACK ƜƝ" button, you can select a track. When you touch "Back - 2007 Toyota Sequoia | Navigation Manual - Page 136
selected from the ones stored in the discs and changed. To turn off the subtitle, touch "Hide". When you touch "Back", the previous screen returns. 5U132a CHANGING THE AUDIO LANGUAGE DVD video only - Each time you touch "Audio", the language is selected from the ones stored in the discs and changed - 2007 Toyota Sequoia | Navigation Manual - Page 137
that are multi−angle compatible when the angle mark appears on the screen. Each time you touch "Angle", the angle changes. When you touch "Back", and the previous screen returns. 5U135a Setup Menu 1 screen 5U136a Setup Menu 2 screen SETUP MENU There are initial setting switches on the "Setup Menu - 2007 Toyota Sequoia | Navigation Manual - Page 138
LANGUAGE CODE". To return to the "Setup Menu 1" screen, touch the "Back" switch. D DVD language You can change the language on the DVD video menu. 1. Touch "DVD Language". 2. Touch the language you want to read on the "Select DVD Language" screen. If you cannot find the language you want to read on - 2007 Toyota Sequoia | Navigation Manual - Page 139
06 06.06 AUDIO SYSTEM 0920 0519 2608 1412 1620 1922 1821 1115 0512 0101 0102 0106 0113 0118 0119 0125 0126 0201 0205 0207 0208 Italian Spanish Chinese Dutch Portuguese Swedish Russian Korean Greek Afar Abkhazian Afrikaans Amharic Arabic Assamese Aymara Azerbaijani Bashkir Byelorussian Bulgarian - 2007 Toyota Sequoia | Navigation Manual - Page 140
Kirundi Romanian Kinyarwanda Sanskrit Sindhi Sangho Serbo−Croatian Sinhalese Slovak Slovenian Samoan Shona Somali Albanian 1918 1919 1920 1921 1923 2001 2005 2007 2008 2009 2011 2012 2014 2015 2018 2019 2020 2023 2111 2118 2126 Serbian Siswati Sesotho Sundanese Swahili Tamil Telugu Tajik Thai - 2007 Toyota Sequoia | Navigation Manual - Page 141
this screen. It you touch the "PICTURE" switch when the vehicle is completely stopped and the parking brake is applied, the video screen returns. 5U138a 5U139a 5U140a V DISPLAYING OPERATION SWITCHES If you touch the part where switches are not located while you are watching video on the video CD - 2007 Toyota Sequoia | Navigation Manual - Page 142
can select a track number by pushing "Ɯ" or "Ɲ" on the "SEEK/TRACK" button. Touch "Back", and the previous screen returns. (g) If the player malfunctions If the player or another unit equipped with the player malfunction, your audio system will display one of the three following messages. If "DISC - 2007 Toyota Sequoia | Navigation Manual - Page 143
high ambient temperature. Remove the magazine from the player and allow the player to cool down. If the malfunction is not rectified: Take your vehicle to your dealer. (h) DVD player and DVD video disc information DVD VIDEO DISCS This DVD player conforms to NTSC color TV formats. The DVD video disc - 2007 Toyota Sequoia | Navigation Manual - Page 144
feature: You can select a language of the subtitle and audio. Region codes: The region codes are provided on DVD players and DVD discs. If the DVD video disc does not have the same region code as the DVD player, you cannot play the disc on the DVD player . Reverse engineering or disassembly - 2007 Toyota Sequoia | Navigation Manual - Page 145
the air conditioning to cool the vehicle interior before you use the players. D Bumpy roads or other vibrations may make your compact disc player and DVD player skip. D If moisture gets into your compact disc player and DVD player, you may not play even though they appear to be working. Remove the - 2007 Toyota Sequoia | Navigation Manual - Page 146
Video CDs " Special shaped discs DVD player D Use only discs marked as shown above. The following products may not be playable on your DVD player. SACD Copy−protected CD CD−R (CD−Recordable) CD−RW (CD−Re−writable) CD−ROM DVD−R DVD+R DVD−RW DVD+RW DVD−ROM DVD−RAM 5U100a " Transparent/translucent - 2007 Toyota Sequoia | Navigation Manual - Page 147
other disc damage could cause the player to skip or to repeat a section of a track. (To see a pin hole, hold the disc up to the light.) D Remove discs from the players when you are not using them. Store them in their plastic cases away from moisture, heat, and direct sunlight. V 5U043a " Labeled - 2007 Toyota Sequoia | Navigation Manual - Page 148
SYSTEM 5U045a To clean a compact disc: Wipe it with a soft, lint−free cloth that has been dampened with water. Wipe in a straight line from the center to the edge of the disc (not in circles). Dry it with another soft, lint−free cloth. Do not use a conventional record cleaner or anti - 2007 Toyota Sequoia | Navigation Manual - Page 149
manual carefully to ensure proper use. Keep this manual in your vehicle at all times. The Navigation System is one of the most technologically advanced vehicle accessories will guide you there. The system will provide both a visual map and audio instructions. The audio instructions will announce - 2007 Toyota Sequoia | Navigation Manual - Page 150
and others. Initial screen When you start the engine or turn the ignition switch to the "ACC" engine running, always apply the parking brake for safety. After a few seconds, the "CAUTION" screen appears. either "English" or "Français" to select a language. Read Touch and follow the instructions - 2007 Toyota Sequoia | Navigation Manual - Page 151
to use this system until they have read and understood the instructions in this manual. For your safety, some functions may become inoperable when the safe operation of your vehicle and the safety of your passengers. Do not use any feature of this system to the extent it distracts you from safe - 2007 Toyota Sequoia | Navigation Manual - Page 152
from the system, look to see whether you can comply with the instruction safely and legally. This system cannot warn you about such things as the safety of an area, condition of streets, and availability of emergency services. If you are unsure about the safety of an area, do not drive into - 2007 Toyota Sequoia | Navigation Manual - Page 153
06 06.06 v - 2007 Toyota Sequoia | Navigation Manual - Page 154
06 06.06 Your navigation system - - Quick reference North−up or heading−up symbol This symbol indicates a map view with north−up or heading−up. Touching this symbol changes the map orientation...9 2 Scale indicator This figure indicates the map scale...9 3 "INFO" button Push this button to display - 2007 Toyota Sequoia | Navigation Manual - Page 155
06 06.06 "Map View" switch Touch this switch to obtain information regarding the route to the destination and information about the POI (Points of Interest) on the map screen...53, 55, 56 9 "AOFF" switch Touch this switch to obtain a broader view. Some of the switches on the screen are not - 2007 Toyota Sequoia | Navigation Manual - Page 156
those registered as "Memory points". (To register memory points, see page 70.) ...37 6 "Emergency" switch You can select one of the three categories of emergency service points that have been already stored in the system's database...36 viii - 2007 Toyota Sequoia | Navigation Manual - Page 157
06 06.06 "Map" switch You can select a destination simply by touching the location on the displayed map...38 8 "Intersection" switch You can enter the names of two intersecting streets. This is helpful if you do not know the specific street address of your destination but know the general vicinity - 2007 Toyota Sequoia | Navigation Manual - Page 158
06 06.06 - "Menu" screen The switches below perform the following operations. 1 "Map DVD" switch Displays information regarding the disc version or covered area...12 2 "Select User" switch Enables recall of up to three memorized user setting patterns...67 3 "Setup" switch Enables various settings - 2007 Toyota Sequoia | Navigation Manual - Page 159
methods to search your home. When you finish memory point registration, the memory point data screen will appear. 6. Touch "Home" switch. Registration of home is complete. RS01002 2. Touch "My Places". xi - 2007 Toyota Sequoia | Navigation Manual - Page 160
for inputting a street name. 1. Push the "DEST" button. RS01008 5. Touch "Enter". The navigation system performs a search for the route. RS01009 2U007a RS01007 6. Touch "Guide", and start driving. 4. Input the street name. City name may be input. For details, see page 28. 2. Touch "Address". xii - 2007 Toyota Sequoia | Navigation Manual - Page 161
.) To use this function, it is necessary to set "Attribute" for the memory point. (To register the "Home", see page xi, 70.) RS01009 4. Touch "Guide", and start driving. Route other than the one recommended can also be selected. (See "-Entering destination" on page 42.) 5. Guidance to your home is