2008 Toyota Highlander Navigation Manual
2008 Toyota Highlander Manual
2008 Toyota Highlander manual content summary:
- 2008 Toyota Highlander | Navigation Manual - Page 1
BASIC FUNCTIONS SECTION BASIC FUNCTIONS Basic information before operation 1 D Initial screen ...22 D Touch screen operation ...24 D Inputting letters and numbers/list screen operation ...24 D Function help ...28 D Map screen operation ...Current position display ...Screen scroll operation ... - 2008 Toyota Highlander | Navigation Manual - Page 2
system - When the "ENGINE START STOP" switch is in ACCESSORY or IGNITION ON mode, the initial screen will be displayed and the system will begin operating. Vehicles without smart key system screen are touched, the screen will change back to "CAUTION" screen and then change to the map screen in about - 2008 Toyota Highlander | Navigation Manual - Page 3
BASIC FUNCTIONS D Maintenance information This system informs about when to replace certain parts or components and shows dealer information (if registered) on the screen. When the vehicle reaches a previously set driving distance or date specified for a - 2008 Toyota Highlander | Navigation Manual - Page 4
can be input via the touch screen. INFORMATION Key layout can be changed. (See "D Input key layout" on page 108.) INFORMATION D If the system does not respond distorted when the display is cold. Under extremely cold conditions, the map may not be displayed and the data input by a user may be - 2008 Toyota Highlander | Navigation Manual - Page 5
To display the alphabet keys, touch "A−Z" or " D To input numerals and symbols To display the number keys and symbol keys, touch "0−9". ". Enter letters by touching the alphabet keys directly. Touching this touch−screen button - 2008 Toyota Highlander | Navigation Manual - Page 6
at a time. This expresses a displayed screen position. INFORMATION The number of matching items is shown to the right side of the screen. If the number of matching items is more than 9,999, the system displays on the screen. If appears to the right of the item name, the complete name is too - 2008 Toyota Highlander | Navigation Manual - Page 7
BASIC FUNCTIONS D Sorting The order of a list displayed on the screen can be rearranged. TYPE A TYPE B 1. Touch "Sort by". "Dist. Sort": To sort in the order of distance from the current vehicle location. The distance from current vehicle position up to the destination is displayed to the right - 2008 Toyota Highlander | Navigation Manual - Page 8
BASIC FUNCTIONS Function help Explanations for the functions of the "Destination", "Setup", and "Menu" screens can be viewed. Map screen operation - - Current position display When starting the navigation system, the current position is displayed first. This screen displays the current vehicle - 2008 Toyota Highlander | Navigation Manual - Page 9
correct. As soon as the system receives signals from the GPS, the correct current position is displayed. D To correct the current position manually, see "D Current position/ tire change calibration" on page 115. Use the scroll feature to move the desired point to the center of the screen for looking - 2008 Toyota Highlander | Navigation Manual - Page 10
. "Add to ": To add a destination. "Replace ": To delete the existing destinations and set a new one. Touch "Mark". When you touch "Mark", the following screen appears for a few seconds, and then the map screen returns. The registered point is shown by on the map. To change the icon or name, etc - 2008 Toyota Highlander | Navigation Manual - Page 11
touched, the position of the cursor is set as a destination. If there is already a set destination, "Add to " and "Replace " are displayed. "Add to ": To add a destination. "Replace ": To delete the existing destinations and set a new one. To register this POI as a memory point, touch "Mark". (See - 2008 Toyota Highlander | Navigation Manual - Page 12
, the position of the cursor is set as a destination. If there is already a set destination, "Add to " and "Replace " are displayed. "Add to ": To add a destination. "Replace ": To delete the existing destinations and set a new one. To edit a memory point, touch "Edit". (See " - Editing memory - 2008 Toyota Highlander | Navigation Manual - Page 13
BASIC FUNCTIONS - Switching the screens Any one of the screen configurations can be selected. Depending on the conditions, certain screen configuration buttons cannot be selected. : To display the single map screen. (See page 34.) : To display the dual map screen. (See page 34.) : To display the - 2008 Toyota Highlander | Navigation Manual - Page 14
map. The map on the left is the main map. The right side map can be edited by touching any specific point on the right side map. This screen can perform the following procedures: 1. Changing the map scale 2. Displaying the POI icon 3. Changing the orientation of the map Touch "OK" when you complete - 2008 Toyota Highlander | Navigation Manual - Page 15
direction of the destination. or until the scale bar Touch changes normally. By continuing to touch the touch−screen button, the scale bar changes smoothly. The scale of the map display can be changed by touching the scale bar directly. It is not available while driving. The map scale is displayed - 2008 Toyota Highlander | Navigation Manual - Page 16
foot print map changes into when the map is scaled down to 150 feet (50 m). D To display building information Information is available only for buildings position is moved to the area which is not covered by the foot print map, the screen scale automatically changes to 150 feet (50 m). D On the - 2008 Toyota Highlander | Navigation Manual - Page 17
, touch the building name. You can see details of the selected POIs. " North−up screen " Heading−up screen The orientation of the map can be changed from north−up to heading−up by touching the orientation symbol at the top left of the screen. North−up symbol Regardless of the direction - 2008 Toyota Highlander | Navigation Manual - Page 18
BASIC FUNCTIONS 38 - 2008 Toyota Highlander | Navigation Manual - Page 19
DESTINATION SEARCH SECTION DESTINATION SEARCH Destination search 2 42 44 44 45 49 52 55 56 56 57 57 58 59 60 60 D Quick reference ("Destination" screen) ...40 D Destination search ...41 Selecting the search area ...Destination search by Home ...Destination search by Quick access ...Destination - 2008 Toyota Highlander | Navigation Manual - Page 20
button. 1 "Address" A house number and the street address can be input by using the input keys...45 2 "POI Name" Select one of the many POIs (Points "Emergency" One of the four categories of emergency service points that are already stored in the system's database can be selected...55 7 "Map" A - 2008 Toyota Highlander | Navigation Manual - Page 21
(interstate) entrance or exit can be entered...58 10 "?" Function help for the "Destination" screen can be viewed on this screen...28 11 "Change" To change the search area, touch this touch−screen button...42 12 Quick access touch−screen buttons One of 5 preset destinations can be selected by - 2008 Toyota Highlander | Navigation Manual - Page 22
- Selecting the search area SELECTING THE SEARCH AREA ON THE DESTINATION SCREEN 1. Push the "DEST" button. SELECTING THE SEARCH AREA ON THE INPUT SCREEN Change the search area in order to set a destination from a different area by using "Address", "POI Name", "Freeway Ent./ Exit", or "Intersection - 2008 Toyota Highlander | Navigation Manual - Page 23
Utah Wyoming Iowa Kansas Minnesota Missouri North Dakota Nebraska South Dakota Oklahoma Texas Illinois Indiana Kentucky Michigan Ohio Wisconsin Arkansas Alabama Louisiana Mississippi Tennessee Connecticut Massachusetts Maine New Hampshire New Jersey New York Rhode Island Vermont "US10" "HI" "US9 - 2008 Toyota Highlander | Navigation Manual - Page 24
" for the memory point. (To register "Home", see page 100.) 2. Touch any of the quick access touch−screen buttons on the "Destination" screen. The screen changes and displays the map location of the quick access point and the route preference. (See "Starting route guidance" on page 60.) To use this - 2008 Toyota Highlander | Navigation Manual - Page 25
Touch numerals directly on the screen to input a house number. After inputting a house number, touch "OK" to display the screen for inputting a street name. It is possible to input a street name first. Touch "Street" to display the screen for inputting a street name. 2. Input the street name. 45 - 2008 Toyota Highlander | Navigation Manual - Page 26
" on page 60.) If the same address exists in more than one city, the current screen changes to the city list screen. If inputting a street name first, the screen changes. The house number can then be input. If the above screen appears, an address range on the screen can be selected. 4. Select or - 2008 Toyota Highlander | Navigation Manual - Page 27
a city name. To search by city, the following three methods are possible. 1. Input the city name 2. Select from the nearest 5 cities 3. Select from the last 5 cities INFORMATION D To change the search area, touch "Search Area". D To cancel the city setting, touch "Any City". 3. Touch the touch - 2008 Toyota Highlander | Navigation Manual - Page 28
5 CITIES 2. Touch the touch−screen button of the desired city name from the displayed list. The current screen changes to the screen for inputting a house number or a street name. (See "(a) Inputting a house number and a street name" on page 45.) Touch the touch−screen button of the desired city - 2008 Toyota Highlander | Navigation Manual - Page 29
button. 2. Touch "POI Name" on the "Destination" screen. 3. Input the name of the Point of Interest. Touch the touch−screen button 4. Touch the touch−screen button of the desired destination. The screen changes and displays the map location of the selected destination and the route preference. - 2008 Toyota Highlander | Navigation Manual - Page 30
by city, the following three methods are possible. 1. Input the city name 2. Select from the nearest 5 cities 3. Select from the last 5 cities 3. Touch the touch−screen button of the desired city name from the displayed list. INFORMATION D To change the search area, touch "Search Area". D To - 2008 Toyota Highlander | Navigation Manual - Page 31
DESTINATION SEARCH SELECTING FROM THE NEAREST 5 CITIES 1. Touch "Nearest 5 Cities". SELECTING FROM THE LAST 5 CITIES 2. Touch the touch−screen button of the desired city name. Touch the touch−screen button of the desired city name. If the navigation has not be used, no cities will be displayed - 2008 Toyota Highlander | Navigation Manual - Page 32
category is not on the screen, touch "List All Categories" to list all POI categories. 3. Set the search point by the following method: 1. Input the city center 2. Set the current position as the search point 3. Set the search point via the map screen 4. Set the search point from any destination It - 2008 Toyota Highlander | Navigation Manual - Page 33
the "POI Category" screen will be displayed. SETTING THE SEARCH POINT VIA THE MAP SCREEN 1. Touch "Map". 2. Input the city center name. 3. Touch the touch−screen button of the desired city center name. When an arrow facing the desired point is touched, the map scrolls in that direction. Releasing - 2008 Toyota Highlander | Navigation Manual - Page 34
DESTINATION SEARCH SETTING THE SEARCH POINT FROM DESTINATIONS 1. Touch the destination buttons at the bottom of the screen. D To search POIs near the search point When the search point is set, the "POI Category" screen will be displayed. When an arrow facing the desired point is touched, the map - 2008 Toyota Highlander | Navigation Manual - Page 35
guidance" on page 60.) "On Route": When the indicator is illuminated by touching this touch−screen button, the list changes and displays the map location of the selected destination and the route preference. (See "Starting route guidance" on page 60.) INFORMATION The navigation system does not guide - 2008 Toyota Highlander | Navigation Manual - Page 36
and up to 100 previously set destinations are displayed on the screen. 3. Touch the touch−screen button of the desired destination. The screen changes and displays the map location of the selected destination and the route preference. (See "Starting route guidance" on page 60.) INFORMATION The list - 2008 Toyota Highlander | Navigation Manual - Page 37
even while driving. However, the cursor cannot be moved. 4. Touch the touch−screen button of the desired item. After inputting the two intersecting streets, the screen changes and displays the map location of the selected destination and the route preference. (See "Starting route guidance" on page - 2008 Toyota Highlander | Navigation Manual - Page 38
Destination search by "Freeway Ent./Exit" 1. Push the "DEST" button. 2. To input a freeway entrance or exit, touch "Freeway Ent./Exit" on the "Destination" screen. If the same two streets cross at more than one intersection, the screen changes and displays the menu to select the city name where the - 2008 Toyota Highlander | Navigation Manual - Page 39
list is displayed by touching this touch−screen button and inputting the name. 3. Input the latitude and the longitude. 4. When the input is finished, touch "OK". By touching the touch−screen button of the desired point, the screen changes and displays the map location of the selected destination - 2008 Toyota Highlander | Navigation Manual - Page 40
2. Touch "Enter". The system starts route search and displays recommended routes. If there is already a set destination, "Add to " and "Replace " are displayed. "Add to ": To add a destination. "Replace ": To delete the existing destinations and set a new one. "Route Preference": To change the route - 2008 Toyota Highlander | Navigation Manual - Page 41
route nor a route without traffic congestion. Route guidance may not be available if there is no road data for the specified location. When To start guidance, touch "Guide". "3 Routes": To select the desired route from three possible routes. (See page 63.) "Route": To change the route. (See pages - 2008 Toyota Highlander | Navigation Manual - Page 42
DESTINATION SEARCH D To change the route before starting guidance ROUTE PREFERENCE INFORMATION D Even if the "Allow Freeway" indicator is dimmed, the route of GPS signals, it is automatically corrected. 1. You can change route preference by touching "Route Preference". 2. Select desired route - 2008 Toyota Highlander | Navigation Manual - Page 43
2. Touch "Quick1", "Quick2" or "Short" to select the desired route. "Quick1": Recommended route. This route is indicated by an orange line. "Quick2": Alternative route. This route is indicated by a purple line. "Short": A route by which you can reach the destination in the shortest distance. This - 2008 Toyota Highlander | Navigation Manual - Page 44
DESTINATION SEARCH 64 - 2008 Toyota Highlander | Navigation Manual - Page 45
ROUTE GUIDANCE SECTION ROUTE GUIDANCE Route guidance 3 D Route guidance screen ...66 D Typical voice guidance prompts ...69 D Distance and time to destination ...71 D Setting and deleting destination ...72 Adding destinations ...Reordering destinations ...Deleting destinations ...D Setting route - 2008 Toyota Highlander | Navigation Manual - Page 46
the next junction and exit, or POIs in the vicinity of the freeway exit. 1 2 3 4 5 Distance to the next turn and the arrow indicating turning direction Current street name Distance and travel/arrival time to the destination Current position Guidance route 1 2 3 4 5 INFORMATION D If the vehicle - 2008 Toyota Highlander | Navigation Manual - Page 47
ROUTE GUIDANCE D When approaching a freeway exit or junction When the vehicle approaches an entrance, exit, or junction, the guidance screen for the freeway will be displayed. D When approaching an intersection When the vehicle approaches an intersection, the intersection guidance screen will be - 2008 Toyota Highlander | Navigation Manual - Page 48
ROUTE GUIDANCE D Other screens TURN LIST SCREEN On this screen, the list of turns on the guidance route can be viewed. Touching the turn list. during guidance displays ARROW SCREEN On this screen, information about next turns on the guidance route can be viewed. Touching during guidance displays - 2008 Toyota Highlander | Navigation Manual - Page 49
ROUTE GUIDANCE Typical voice guidance prompts The voice guidance provides various messages as you approach an intersection, or other point where you need to maneuver the vehicle. 4.2 miles 0.25 miles 4.7 miles 0.25 miles +α 1 "Proceed about 4 miles to the traffic circle." "In a quarter of a mile - 2008 Toyota Highlander | Navigation Manual - Page 50
ROUTE GUIDANCE One−way road One−way road ∗: The system indicates a U−turn if the distance between two one−way roads (of opposite directions) is less than 50 feet (15 m) in residential areas or 164 feet (50 m) in non−residential areas. 1 The system announces the approach to the final destination - 2008 Toyota Highlander | Navigation Manual - Page 51
Displayed while driving off the guidance route. The destination direction is indicated by an arrow. INFORMATION When the vehicle is on the guidance along the route is displayed. Travel time and arrival time is calculated based on the set vehicle speed information. (See page 107.) However, when - 2008 Toyota Highlander | Navigation Manual - Page 52
routes can be done. - Reordering destinations When more than one destination is set, you can change the arrival order of the destinations. 1. Touch "Route". 1. Touch "Route". 2. Touch "Add". 3. Input an additional destination in the same way as the destination search. (See "Destination search" on - 2008 Toyota Highlander | Navigation Manual - Page 53
ROUTE GUIDANCE - Deleting destinations 4. After selecting the destinations, touch "OK". The system searches for the guidance route again, and displays the entire route. Even if "OK" is not touched, the entire route is displayed automatically within a few - 2008 Toyota Highlander | Navigation Manual - Page 54
If "No" is touching, the previous screen will return. 5. If more than one destination is set, touch "OK" after deleting the destinations. The system searches for the guidance route again, and displays the entire route. You can designate the route conditions of the route to the destination. 1. Touch - 2008 Toyota Highlander | Navigation Manual - Page 55
the route where a delay is caused by road repairs, or an accident, etc. The entire route from the starting point to the destination is displayed. "Guide": To start guidance. "Route": To change a route. (See pages 72 and 74.) 1. Touch "Route". 2. Touch "Detour". 75 - 2008 Toyota Highlander | Navigation Manual - Page 56
"Whole Route": By touching this touch− screen button, the system will calculate an entire new route to the destination. This picture shows an example of how the system would guide around a delay caused by a traffic jam. 1 This position indicates the location of a traffic jam caused by road repairs - 2008 Toyota Highlander | Navigation Manual - Page 57
freeway.) 1. Touch "Route". 1. Touch "Route". 2. Touch "Route Preference" to change the conditions which are to determine the route to the destination. 2. Touch "Start on/off. When searching for a route, the system will avoid routes for preferences that are deselected. 4. After choosing the conditions, - 2008 Toyota Highlander | Navigation Manual - Page 58
then displays the complete POI listing screen. "Local POI List": When searching for the nearest Point of Interest, touch this touch− screen button. The system will list the points within 20 miles (32 km). (See page 80.) A screen with a limited choice of Points of Interest will be displayed. (To - 2008 Toyota Highlander | Navigation Manual - Page 59
ROUTE GUIDANCE Touch "Other POIs" on the "Display POI Icons" screen. When a Point of Interest category is selected from either the limited list or the complete list, the screen will display symbols at those locations on the map screen. Select the desired POI categories. The selected category icon - 2008 Toyota Highlander | Navigation Manual - Page 60
the map screen. "On Route": When the indicator is illuminated by touching this touch−screen button, . The map will shift so that the icon is centered on the screen and overlaps with the . At this the cursor, touch "Enter ". The screen changes and displays the map location of the selected destination - 2008 Toyota Highlander | Navigation Manual - Page 61
marks indicate the direction in which you should turn at an intersection. Touch "Map" on the "Turn List" screen. The point which you choose is displayed on the map screen. The entire route from the current position to the destination is displayed. "Guide": To start guidance. "Route": To change the - 2008 Toyota Highlander | Navigation Manual - Page 62
ROUTE GUIDANCE - Route preview 1. Touch "Map View". : To indicate the next destination. : To preview the route to the next destination. : To preview review the route to the previous destination or starting point in fast−forward mode. : To indicate the previous destination or starting point. 82 - 2008 Toyota Highlander | Navigation Manual - Page 63
It is possible to store the traveled route up to 124 miles (200 km) and retrace the route on the display. INFORMATION This feature is available on the map with more detailed map scale than 30 mile (50 km). "Record": To start recording the route trace. "Stop": To stop recording the - 2008 Toyota Highlander | Navigation Manual - Page 64
ROUTE GUIDANCE 84 - 2008 Toyota Highlander | Navigation Manual - Page 65
AUDIO/VIDEO SYSTEM SECTION AUDIO/VIDEO SYSTEM Audio/video system 6 D Quick reference ...186 D Using your audio/video system ...187 D Audio/video remote controls ...240 D Audio/video system operating hints ...241 185 - 2008 Toyota Highlander | Navigation Manual - Page 66
AUDIO/VIDEO SYSTEM Quick reference 1 2 3 4 AUX on. For details, see pages 189, 192, 206 and 218. 5 6 "SCAN" button Push this button to scan radio stations or scan the tracks, discs, files or folders. For details, see pages 195, 209, 213, 220 and 223. "TUNE/FILE"/"AUDIO" knob Push this knob - 2008 Toyota Highlander | Navigation Manual - Page 67
Using your audio/video system - - Some basics 8 9 "PWR/VOL" knob Push this knob to turn the audio/video system on and off, and turn it to adjust the volume. For details, see page 188. "SEEK/TRACK" button Push either side of this button to seek up or down for a station, or to access a desired - 2008 Toyota Highlander | Navigation Manual - Page 68
VIDEO SYSTEM (a) Turning the system on and off CAUTION For vehicles sold in U.S.A. and Canada: D Part 15 of the FCC Rules FCC Warning: Any unauthorized changes "PWR/VOL": Push this knob to turn the audio/video system on and off. Turn this knob to adjust the volume. The system turns on in the last - 2008 Toyota Highlander | Navigation Manual - Page 69
AUDIO/VIDEO SYSTEM (b) Switching between functions Push "AM·SAT", "FM 1·2" or "DISC·AUX" button to turn on the desired off each player by ejecting all the discs. If the audio/video system was previously off, then the entire audio/video system will be turned off when you eject all the discs. If - 2008 Toyota Highlander | Navigation Manual - Page 70
if you are listening to a stereo recording or broadcast, changing the right/left balance will increase the volume of one group of sounds while decreasing the volume of another. 1. Push the "TUNE/FILE"/"AUDIO" knob. INFORMATION D If the system does not respond to a touch of a touch−screen button - 2008 Toyota Highlander | Navigation Manual - Page 71
Adjusts mid−pitched tones. "BASS": Adjusts low−pitched tones. screen size (with rear seat entertainment system) Touching "WIDE" displayed on the screen in the video control mode will display the wide mode control screen. "NORMAL": Displays a 3 4 screen, with either side - 2008 Toyota Highlander | Navigation Manual - Page 72
rear seat entertainment system) The sound of the rear seat entertainment system can be enjoyed by pushing the "DISC·AUX" button. NOTICE D Do not stack up two discs for insertion, or it will cause damage to the changer. Insert only one disc into slot at a time. D Never try to disassemble or oil any - 2008 Toyota Highlander | Navigation Manual - Page 73
AUDIO/VIDEO SYSTEM - Radio operation (h) AUX adapter The sound of portable audio players connected to the AUX adapter can be enjoyed. Push the "DISC·AUX" button to switch to AUX mode. For details, refer to the "Owner's Manual". (a) Listening to the radio Push these buttons to choose either an AM - 2008 Toyota Highlander | Navigation Manual - Page 74
AUDIO/VIDEO SYSTEM Turn the knob clockwise to step up the station band or counterclockwise to step down. Your radio automatically changes to stereo reception (AM, FM1 or FM2) can store up to 6 stations. To change the preset station to a different one, follow the same procedure. The preset station - 2008 Toyota Highlander | Navigation Manual - Page 75
Seek tuning: Push the "SEEK/TRACK" button on either side. The radio will begin seeking up or down for a button again. (d) Radio Data System Your audio/video system is equipped with Radio Data Systems (RDS). RDS mode provides you are available for the use only on FM stations which broadcast - 2008 Toyota Highlander | Navigation Manual - Page 76
) D EASY LIS (Easy listening) D CLS/JAZZ (Classical music and Jazz) D R & B (Rhythm and Blues) D RELIGION D ALARM (Emergency message) "TYPE SEEK" When a program is set, "TYPE SEEK" appears. Touch the switch and the system starts to seek the station in the relevant program type. If any type program - 2008 Toyota Highlander | Navigation Manual - Page 77
"MSG" (MESSAGE) If the system receives a radio text from an RDS station, "MSG" appears on the display. Touch "MSG", and a text message is displayed on the screen. This function is available only when the vehicle is not moving. When you touch "MSG OFF", the display returns. (e) Traffic announcement - 2008 Toyota Highlander | Navigation Manual - Page 78
availability and content of the satellite radio services provided, which are subject to the terms and conditions of the XMr radio customer service radio ID when activating XMr service or when reporting a problem. If you select the "CH 000" using the "TUNE/FILE"/"AUDIO" knob, the ID code of - 2008 Toyota Highlander | Navigation Manual - Page 79
SYSTEM D Listening to satellite radio D Channel category Touch either "TYPEA" or "TYPE"" to go to the next or previous category. Push the "AM·SAT" button to choose either an AM station or a SAT (satellite) channel. Besides "AM", "SAT1", "SAT2" or "SAT3" appears on the display. Turn this knob - 2008 Toyota Highlander | Navigation Manual - Page 80
AUDIO/VIDEO SYSTEM D Presetting a channel 1. Tune in the desired channel. D Selecting a channel Tune appears on the touch−screen button. Each touch−screen button can store three SAT channels. To change the preset channel to a different one, follow the same procedure. The preset channel memory is cancelled - 2008 Toyota Highlander | Navigation Manual - Page 81
AUDIO/VIDEO SYSTEM D Displaying the title and name To scan the currently selected channel category: Touch "TYPE SCAN" or push the "SCAN" button briefly. "SCAN" appears on the - 2008 Toyota Highlander | Navigation Manual - Page 82
about 2 seconds until the radio returns to the previous channel or "CH001". If it does not change automatically, select another channel. NO SIGNAL LOADING OFF AIR The XMr Listener Care Center is also available on the phone, please call 1−800−967−2346 during the following hours: Monday - Saturday - 2008 Toyota Highlander | Navigation Manual - Page 83
SYSTEM installed and used in accordance with the instructions, may cause harmful interference to radio Alternation or modifications carried out without appropriate authorization may invalidate the user's right to operate the equipment. INFORMATION This XMr tuner supports "Audio Services - 2008 Toyota Highlander | Navigation Manual - Page 84
without smart key system - The engine switch must be set at "ACC" or "ON" position. Your CD changer can store up to 4 discs. You can set a disc at the lowest empty disc number. 1. Push the "LOAD· /CLOSE" button. The "LOAD·EJECT" screen appears. 3. The amber indicators at either side of the slot - 2008 Toyota Highlander | Navigation Manual - Page 85
" button. The "LOAD·EJECT" screen appears. INFORMATION Under extremely cold conditions, the display may react slowly or operation sound may become louder. 2. Touch the disc number to be ejected. The display opens and the amber indicators at either side of the slot start blinking. After the disc is - 2008 Toyota Highlander | Navigation Manual - Page 86
within 15 seconds after it is ejected, the operation will be canceled. When all the discs are removed, the amber indicators change to green. A disc can be inserted. (c) Playing a disc Push the "DISC·AUX" button if the discs are already loaded in the changer. "CD CHANGER" appears on the screen. The - 2008 Toyota Highlander | Navigation Manual - Page 87
AUDIO/VIDEO SYSTEM (d) Selecting a desired disc Touch the desired disc number on the screen. The selected disc number is highlighted. The changer will start playing the selected disc from the first track. (e) Playing an audio disc Push the "TUNE/FILE"/"AUDIO" knob to display this screen. 207 - 2008 Toyota Highlander | Navigation Manual - Page 88
list is displayed, the top page is displayed. Vehicles with rear entertainment system - While the DVD player is in operation, the chapter or track can be changed by pushing either side of the "SEEK/TRACK" button. Fast forward: Push " " side of the "SEEK/TRACK" button and hold it to fast forward the - 2008 Toyota Highlander | Navigation Manual - Page 89
AUDIO/VIDEO SYSTEM SEARCHING FOR A DESIRED TRACK OR DISC Searching for a desired track - Touch "SCAN" on the screen or push the "SCAN" button briefly while the disc is - 2008 Toyota Highlander | Navigation Manual - Page 90
order - Touch "RAND" briefly while the disc is playing. "RAND" appears on the screen. The system selects a track on the disc being listened to in random order. To cancel it, touch "RAND" a MP3/WMA disc Push the "TUNE/FILE"/"AUDIO" knob and touch a MP3/WMA disc number to display this screen. 210 - 2008 Toyota Highlander | Navigation Manual - Page 91
AUDIO/VIDEO SYSTEM SELECTING A DESIRED FOLDER "FOLDERY": Touch this touch−screen button to go to the next folder. "FOLDERB": Touch this touch−screen button to go to the previous folder. "FOLDER LIST": The desired folder can be selected in a list. This function is available only when the vehicle is - 2008 Toyota Highlander | Navigation Manual - Page 92
: Push " " side of the "SEEK/ TRACK" button and hold it to reverse the disc. When you release the button, the changer will resume playing. "TUNE/FILE"/"AUDIO" knob: Use for direct a list. This function is available only when the vehicle is not moving. Touch "FILE". The file list is displayed. 212 - 2008 Toyota Highlander | Navigation Manual - Page 93
AUDIO/VIDEO SYSTEM Touch the desired file number. The changer will start playing the The folder list is displayed. "DETAIL": Details of the file currently playing is displayed. This function is available only when the vehicle is not moving. SEARCHING FOR A DESIRED FILE Touch "SCAN" on the screen or - 2008 Toyota Highlander | Navigation Manual - Page 94
AUDIO/VIDEO SYSTEM SEARCHING FOR A DESIRED FOLDER Touch "SCAN" on the screen or push the "SCAN" button for longer than a second while the disc is playing. "FLD.SCAN" - 2008 Toyota Highlander | Navigation Manual - Page 95
or the system has trouble. Push the "DISC" button once again. If the changer does not operate, check that the disc surface is not soiled or damaged. If the disc is O.K., the temperature of the changer's internal mechanism may be raised because of high external temperature. Remove - 2008 Toyota Highlander | Navigation Manual - Page 96
disc is loaded in the DVD player. A WMA disc cannot be played. For details of "Rear seat entertainment system", refer to "Owner's Manual". For appropriate discs for this player, see "Audio/video system operating hints" on page 241. (a) Inserting the disc Insert the disc into the slot with the label - 2008 Toyota Highlander | Navigation Manual - Page 97
AUDIO/VIDEO SYSTEM NOTICE Never try to disassemble or oil any part of the DVD player. Do not insert anything other than a disc into the slot. (b) Ejecting a disc Push the button. 217 - 2008 Toyota Highlander | Navigation Manual - Page 98
AUDIO/VIDEO SYSTEM (c) Playing a disc Push the "DISC·AUX" button if a disc is already loaded in the player. "DVD" appears on the screen. (If The disc title and track title will appear on the screen when pushing the "DISC·AUX" button. Push the "TUNE/FILE"/"AUDIO" knob to display this screen. 218 - 2008 Toyota Highlander | Navigation Manual - Page 99
either side of the "SEEK/TRACK" button and repeat it until the desired track number appears on the display. As you release the button, the player will start playing the selected track from the beginning. "TRACK LIST": The desired track can be selected from a list. This function is available only - 2008 Toyota Highlander | Navigation Manual - Page 100
AUDIO/VIDEO SYSTEM SEARCHING FOR A DESIRED TRACK Touch "SCAN" on the screen or for automatic and random selection of the disc which you are currently listening to. When "RAND" is touched, the system selects a track in the disc you are currently listening to. To cancel it, touch "RAND" once again. - 2008 Toyota Highlander | Navigation Manual - Page 101
AUDIO/VIDEO SYSTEM (e) Operating a MP3 DISC PLAYING A MP3 DISC Push the "TURN/FILE" knob to display this screen. displayed. "DETAIL": Details of the file currently playing is displayed. This function is available only when the vehicle is not moving. "FOLDERY": Touch this touch−screen button - 2008 Toyota Highlander | Navigation Manual - Page 102
SYSTEM Details of the file currently playing is displayed. This function is available only when the vehicle is not moving. SELECTING A DESIRED FILE " button, the player will resume playing from that position. Reverse: Push " " side of the "SEEK/ TRACK" button and hold it to reverse the disc. When - 2008 Toyota Highlander | Navigation Manual - Page 103
AUDIO/VIDEO SYSTEM SEARCHING FOR A DESIRED FILE Touch "SCAN" on the screen or push the "SCAN" button briefly. "SCAN" appears on the screen. The DVD player will play - 2008 Toyota Highlander | Navigation Manual - Page 104
random order - Touch "RAND" briefly. "RAND" appears on the screen. The system selects a file in the folder you are currently listening to. To cancel it, "RAND" until the beep sounds. "FLD.RAND" appears on the screen. The system selects a file in the folders of all the trays which are set and plays - 2008 Toyota Highlander | Navigation Manual - Page 105
/VIDEO SYSTEM (f) Operating a DVD video disc NOTE: The playback condition of some DVD video discs may be determined by a DVD video software producer. This DVD player plays a disc as the software producer intended. So some functions may not work properly. Be sure to read the instruction manual for - 2008 Toyota Highlander | Navigation Manual - Page 106
AUDIO/VIDEO SYSTEM PLAYING A DVD DISC Push the "TUNE/FILE"/"AUDIO" knob to display this screen. When you touch "WIDE", the screen mode can be changed. It you touch "PICTURE" when the vehicle is completely stopped and the parking brake is applied, the video screen returns. DISPLAYING DVD CONTROLS If - 2008 Toyota Highlander | Navigation Manual - Page 107
SYSTEM DESCRIPTION OF DVD CONTROLS D Top page of DVD video controls "Menu" and "Top Menu": If you touch any of the above controls, the menu screen for DVD video appears. (For the operation, see the manual controls "Setup": The changing screen appears. (See page 229.) "Subtitle": The subtitle changing - 2008 Toyota Highlander | Navigation Manual - Page 108
SYSTEM SELECTING A MENU ITEM Enter the menu item using Y, ", B and A and touch "Enter". The player starts playing video for that menu item. (For details, see the manual player starts playing video for that title number. When you push either side of the "SEEK/ TRACK" button, you can select a chapter. - 2008 Toyota Highlander | Navigation Manual - Page 109
AUDIO/VIDEO SYSTEM CHANGING THE SUBTITLE LANGUAGE Each time you touch "Subtitle", the language is selected from the ones stored in the discs and changed. When you touch screen returns. , the previous CHANGING THE AUDIO LANGUAGE Each time you touch "AUDIO", the language is selected from the ones - 2008 Toyota Highlander | Navigation Manual - Page 110
AUDIO/VIDEO SYSTEM CHANGING THE ANGLE The angle can be selected for discs that are multi−angle compatible when the angle mark appears on the screen. Each time you touch "Angle", the angle changes. When you touch screen returns. , and the previous SETUP MENU There are initial setting touch−screen - 2008 Toyota Highlander | Navigation Manual - Page 111
SYSTEM D Subtitle language You can change Setup Menu" screen, . touch the D Parental lock The level of viewer restrictions can be changed to return to the "Setup Menu" screen. D DVD language You can change the language on the LANGUAGE CODE". To return to the "Setup Menu" screen, . touch D Angle - 2008 Toyota Highlander | Navigation Manual - Page 112
AUDIO/VIDEO SYSTEM ENTER AUDIO LANGUAGE CODE 0113 0118 0119 0125 0126 0201 0205 If you touch "Others" on the "Select Audio Language" screen, "Select Subtitle Language" screen - 2008 Toyota Highlander | Navigation Manual - Page 113
AUDIO/VIDEO SYSTEM 0801 0809 0818 0821 0825 0901 0905 0911 0914 0919 0923 1009 1023 1101 1111 1112 1113 1114 1119 1121 1125 1201 1214 1215 1220 - 2008 Toyota Highlander | Navigation Manual - Page 114
you want to cancel the setup operation from the rear seat, touch "Play". The player will resume normal play. Under the same condition, the rear passenger can cancel the setup operation from the front seat. To lock the operation of the player from the rear seat, see "(c) Rear system lock" on page 181 - 2008 Toyota Highlander | Navigation Manual - Page 115
AUDIO/VIDEO SYSTEM (g) Operating a video CD PLAYING A VIDEO CD Push the "AUDIO" button to display this screen. When you touch "WIDE", the screen mode can be changed. It you touch "PICTURE" when the vehicle is completely stopped and the parking brake is applied, the video screen returns. DISPLAYING - 2008 Toyota Highlander | Navigation Manual - Page 116
AUDIO/VIDEO SYSTEM DESCRIPTION OF VIDEO CD CONTROLS D Controls on top page "Select Number": is playing video, the next track is searched and played. "Main/Sub": A multiplex transmission changing control. The mode changes from Main/Sub to Main, to Sub and back to Main/Sub by touching this control. - 2008 Toyota Highlander | Navigation Manual - Page 117
player malfunction, your audio/video system will display following messages. If "DISC CHECK" appears on the display: It indicates that the disc dirty, damaged the display: It indicates that the inside of the player unit may be too hot due to the very high ambient temperature. Remove the disc from the - 2008 Toyota Highlander | Navigation Manual - Page 118
AUDIO/VIDEO SYSTEM (i) DVD player and DVD video disc information DVD VIDEO DISCS This DVD player conforms to NTSC color TV formats. The DVD video disc conforming to another formats such as PAL or SECAM cannot be used. Region codes: Some DVD video discs have a region code indicating a country where - 2008 Toyota Highlander | Navigation Manual - Page 119
in which the volume of data assigned to the picture is changed depending on the picture format has also been adopted. Audio data discs cannot be played at all, or violent scenes are skipped or replaced with other scenes. Level 1: DVD video discs for children can be played. Systems, Inc. 239 - 2008 Toyota Highlander | Navigation Manual - Page 120
a desired disc: Push and hold the " " or " " switch until you hear a beep to change to the next or the previous disc. Repeat this operation until you reach the disc you want to listen to. Vehicles with rear seat entertainment system - While the DVD player is in operation, the chapter or track can be - 2008 Toyota Highlander | Navigation Manual - Page 121
the vehicle may cause a noise from the speakers of the audio/video system which you are listening to. However, this does not indicate a malfunction. RADIO RECEPTION Usually, a problem with radio reception does not mean there is a problem with your radio - it is just the normal result of conditions - 2008 Toyota Highlander | Navigation Manual - Page 122
SYSTEM large objects. Increasing the bass level may reduce static to sound alternately strong and weak electrical noise, such as high tension power lines, lightening, or . On hot days, use the air conditioning to cool the vehicle interior they appear to be working. Remove the disc from the changer - 2008 Toyota Highlander | Navigation Manual - Page 123
AUDIO/VIDEO SYSTEM Audio CDs Audio CDs DVD video discs CD changer D Use only discs marked as shown above. The following products may not be playable on your - 2008 Toyota Highlander | Navigation Manual - Page 124
shown in the illustrations. The use of such discs may damage the player or changer, or it may be impossible to eject the disc. D This system is not designed for use of Dual Disc. Do not use Dual Disc because it may cause damage to the player or changer. " Transparent/translucent - 2008 Toyota Highlander | Navigation Manual - Page 125
Avoid getting fingerprints on them, particularly on the shiny side. D Dirt, scratches, warping, pin holes, or other disc damage could cause the player to skip or to repeat a section of a track. (To see a pin hole, hold the disc up to the light.) D Remove discs from the players when you are not using - 2008 Toyota Highlander | Navigation Manual - Page 126
as an ID3 tag. WMA tags carry information such as track title, artist name. D The emphasis function is available only when playing MP3/WMA files recorded at 32, 44.1 and 48 kHz. (The system can play MP3 files with sampling frequencies of 16, 22.05, and 24 kHz. However, the emphasis function - 2008 Toyota Highlander | Navigation Manual - Page 127
AUDIO/VIDEO SYSTEM 001.mp3 002.wma Folder 1 003.mp3 Folder 2 004.wma 005.mp3 Folder 3 006.mp3 D The play order of the compact disc with the begin more slowly than with a conventional CD or CD−R disc. D Recordings on CD−R/CD−RW cannot be played using the DDCD (Double Density CD) system. 247 - 2008 Toyota Highlander | Navigation Manual - Page 128
AUDIO/VIDEO SYSTEM TERMS Packet write- This is a general term that describes the process of (MPEG) of the ISO (International Standard Organization). MP3 compresses audio data to about 1/10 the size of that on conventional discs. WMA- WMA (Windows Media Audio) is an audio compression format developed - 2008 Toyota Highlander | Navigation Manual - Page 129
APPENDIX SECTION APPENDIX Appendix 8 D Limitations of the navigation system ...256 D Map database information and updates ...258 255 - 2008 Toyota Highlander | Navigation Manual - Page 130
tall buildings, trucks, or even the placement of objects on the instrument panel may obstruct the GPS signals. The GPS satellites may not send signals to repairs or improvements being made to them. Even when the navigation system is receiving clear GPS signals, the vehicle position may not be shown - 2008 Toyota Highlander | Navigation Manual - Page 131
change of direction by going forward and backward, or turning on a turntable in the parking lot. D When leaving a covered parking lot or parking garage. D When a roof carrier is installed. D When driving with tire chains installed. D When the tires are worn. D After replacing not be available for the - 2008 Toyota Highlander | Navigation Manual - Page 132
APPENDIX Map database information and updates - After replacing the tire, implement the operation described in the "D Current position/tire change calibration". (See page 115.) This navigation system uses tire turning data and is designed to work with factory− specified tires for your vehicle. - 2008 Toyota Highlander | Navigation Manual - Page 133
AND CONDITIONS Personal Use Only. You agree to use this Data together with the navigation system for the solely personal, non− commercial purposes for which you were licensed, and not for service bureau, time−sharing or other similar purposes. Accordingly, but subject to the restrictions set forth - 2008 Toyota Highlander | Navigation Manual - Page 134
APPENDIX Warning. The Data may contain inaccurate or incomplete information due to the passage of time, changing circumstances, sources used and OF THESE TERMS OR CONDITIONS, WHETHER IN AN ACTION IN CONTRACT OR TORT OR BASED ON A WARRANTY, EVEN IF [CLIENT] OR ITS LICENSORS HAVE BEEN ADVISED OF THE - 2008 Toyota Highlander | Navigation Manual - Page 135
refuses to use the legend provided herein, the Contracting Officer, federal government agency, or any federal official must notify NAVTEQ prior to seeking additional or alternative rights in the Data. 261 - 2008 Toyota Highlander | Navigation Manual - Page 136
of this Agreement. You shall not alter, obscure or remove any copyright notices, trademark notices or other restrictive legends relating . LIMITATIONS ON USE The DATABASE is restricted for use in the specific system for which it was created. Except to the extent explicitly permitted by mandatory - 2008 Toyota Highlander | Navigation Manual - Page 137
together with the system for which it INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR COSTS OF COVER, LOSS OF USE OR BUSINESS INTERRUPTION OR THE BY YOU FOR THE DATABASE. WARNINGS The DATABASE comprises facts and information due to the passage of time, changing circumstances, and due to the nature - 2008 Toyota Highlander | Navigation Manual - Page 138
(commercial computer software clause for civilian agencies), DFARS 252.227−7015 (NOV 1995) (DOD technical data − commercial items clause); FAR 52.227−14 Alternates I, II, and III (JUN 1987) (civilian agency technical data and noncommercial computer software clause); and/or FAR 12.211 and FAR 12.212 - 2008 Toyota Highlander | Navigation Manual - Page 139
You may not transfer the POI Data to third parties, except together with the system for which it was created, provided that you do not retain any copy of , and not for service bureau, time−sharing or other similar purposes. You may not modify the information or remove any copyright notices that - 2008 Toyota Highlander | Navigation Manual - Page 140
OF THESE TERMS OR CONDITIONS, WHETHER IN AN ACTION IN CONTRACT OR TORT OR BASED ON A WARRANTY, EVEN IF DENSO OR ITS LICENSORS HAVE BEEN ADVISED OF END USER NOTICE The marks of companies displayed by this product to indicate business locations are the marks of their respective owners. The use of such - 2008 Toyota Highlander | Navigation Manual - Page 141
APPENDIX - Changing the map DVD−ROM There are two types of areas available for route guidance. In one type of area, primarily around metropolitan centers, detailed route guidance is available for the entire area. In the other type of area, all roads are displayed on the map but route guidance is - 2008 Toyota Highlander | Navigation Manual - Page 142
availability braking system. 2. Touch "Map DVD". INFORMATION Under extremely cold conditions, the display may react slowly or operation sound may become louder. Make sure the version of the database on this screen. To display the disc coverage area, touch "Covered Area". Confirm the covered - 2008 Toyota Highlander | Navigation Manual - Page 143
of the most technologically advanced vehicle accessories ever developed. The system receives satellite signals from the Global Positioning System (GPS) operated by the U.S. Department of Defense. Using these signals and other vehicle sensors, the system indicates your present position and assists in - 2008 Toyota Highlander | Navigation Manual - Page 144
HIGHLANDER_Navi_U (L/O 0708) Please be aware that all current vehicle navigation systems have certain limitations that may affect their ability to perform properly. The accuracy of the vehicle's position depends on the satellite condition, road configuration, vehicle - 2008 Toyota Highlander | Navigation Manual - Page 145
manual For safety reasons, this manual indicates items requiring particular attention with the following marks. Safety Instruction CAUTION This is a warning against anything which may cause injury to people if the warning not use any feature of this system to the extent it becomes a distraction - 2008 Toyota Highlander | Navigation Manual - Page 146
, etc.) frequently change. Therefore, before following any instruction from the system, look to see whether the instruction can be done safely and legally. This system cannot warn about such things as the safety of an area, condition of streets, and availability of emergency services. If unsure - 2008 Toyota Highlander | Navigation Manual - Page 147
Quick guide - - Overview buttons and guidance screen No. 1 2 3 4 5 Name North−up or heading−up symbol Scale indicator Zoom out button "DISP" button "INFO" button "Mark" "Route" Function This symbol indicates a map view with north−up or heading−up. Touching this symbol changes the map orientation. - 2008 Toyota Highlander | Navigation Manual - Page 148
this button to display the foot print map and the building information. Touch this button to change the screen mode. Page 78, 81, 82, 83 9 "AA OFF" 110 7, MAP/VOICE" button "GPS" mark (Global Positioning System) Speech command system indicator Push this button to display the "Destination" screen. - 2008 Toyota Highlander | Navigation Manual - Page 149
- Registering home 1 Push "MENU" button. 0U5074X 2 Touch "My Places". 0U5002F 3 Touch "Register" of the home. 0U5003F 4 There are 13 different methods to search your home. 0U5004F See "Destination search" on page 41. 7 - 2008 Toyota Highlander | Navigation Manual - Page 150
5 Touch "Enter". The "Memory Point" screen is displayed. 0U5005F 6 Touch "OK". 0U5006F Registration of home is complete. You can change the icon, quick access, name, location and phone number. (See " - Editing memory points" on page 94.) 8 - 2008 Toyota Highlander | Navigation Manual - Page 151
- Registering preset memory point (Quick access) 1 Push "MENU" button. 0U5074X 2 Touch "My Places". 0U5007F 3 Touch "Register" of the memory points. 0U5008F 4 There are 13 different methods to search a preset memory point. 0U5009F See "Destination search" on page 41. 9 - 2008 Toyota Highlander | Navigation Manual - Page 152
Access". 0U5011F 7 Touch one of preset buttons 1 to 5. 0U5012F 8 Touch "OK". 0U5013F Registration of the preset memory point is complete. You can change the icon, quick access, name, location and phone number. (See " - Editing memory points" on page 94.) The registered points can be used on - 2008 Toyota Highlander | Navigation Manual - Page 153
methods to search destinations. 0U5014F See "Destination search" on page 41. 3 Touch "Enter". 0U5015F The navigation system performs a search for the route. 4 Touch "Guide", and start driving. 0U5016F Routes other than the one recommended can also be selected. (See "Starting route - 2008 Toyota Highlander | Navigation Manual - Page 154
home has been registered. (To register "Home", see " - Registering home" on page 100.) 3 Touch "Enter". The navigation system performs a search for the route. 0U5018F 4 Touch "Guide", and start driving. 0U5019F Routes other than the one recommended can also be selected. (See "Starting route - 2008 Toyota Highlander | Navigation Manual - Page 155
FUNCTIONS SECTION ADVANCED FUNCTIONS Descriptions of functions for more effective use 4 D Quick reference ("Menu" screen) ...86 D Quick reference ("Setup" screen) ...87 D Suspending and resuming guidance ...88 D Volume ...89 D User selection ...90 D My places ...92 Registering memory points - 2008 Toyota Highlander | Navigation Manual - Page 156
Displays information regarding the disc version or covered area...268 1 5 "Select User" Up to 3 different settings for different users can be memorized...90 6 "Setup" Enables various settings for the navigation system...87, 106 7 "My Places" Enables changes to "Memory points", "Home" and "Areas to - 2008 Toyota Highlander | Navigation Manual - Page 157
and touch "Setup". 1 "Distance" The distance units "km" or "miles" can be selected...107 2 "Estimated Travel Time" The system to display the travel time and the arrival time to the destination on the route guidance screen can be set...107 3 "Keyboard Layout" Key layout can be changed...108 4 "Time - 2008 Toyota Highlander | Navigation Manual - Page 158
Adjustment of the current vehicle position mark can be done manually, or mis−calculation by changing tire will be adjusted...115 14 "Default" This touch −screen button initializes all of the settings...106 15 "?" Function help for the "Setup - 2008 Toyota Highlander | Navigation Manual - Page 159
The volume of the voice or turn off voice guidance can be adjusted. 2. Touch "Resume Guidance". 1. Push the "MENU" button. The screen will change to the current position map with route guidance. 2. Touch "Volume". To adjust the volume, select the desired level by touching the appropriate number - 2008 Toyota Highlander | Navigation Manual - Page 160
km/h). To turn the "Adaptive Volume Control" system on, touch the button. The indicator will be highlighted. The system can memorize the following settings for up to three users. D Map direction D Map scale D Map configuration D Guidance mode D Setup D Volume D Language D Route trace D Travel time - 2008 Toyota Highlander | Navigation Manual - Page 161
ADVANCED FUNCTIONS D To register D To change user 1. Touch "Memorize". The confirmation screen will be displayed. Touch "User number". touch−screen button that is already registered is touched, the following screen appears. To replace, touch "Yes". To cancel the replacement, touch "No" or . 91 - 2008 Toyota Highlander | Navigation Manual - Page 162
ADVANCED FUNCTIONS My places - D To delete user Points or areas on the map can be registered. The registered points can be used on the "Destination" screen. (See " - Destination search by Home" on page 44 and " - Destination search by Quick access" on page 44.) Registered areas are avoided at the - 2008 Toyota Highlander | Navigation Manual - Page 163
ADVANCED FUNCTIONS - Registering memory points 1. Push the "MENU" button. 2. Touch "My Places". On this screen, the following operations can be performed. 1 Registers memory points. (See " - Registering memory points" on page 93.) 2 Edits memory points. (See " - Editing memory points" on page 94.) - 2008 Toyota Highlander | Navigation Manual - Page 164
ADVANCED FUNCTIONS - Editing memory points The icon, attribute, name, location and/or telephone number of a registered memory point can be edited. 1. Push the "MENU" button. 2. Touch "My Places". 5. Touch "OK". To edit registered information, see " - Editing memory points" on page 94. INFORMATION - 2008 Toyota Highlander | Navigation Manual - Page 165
ADVANCED FUNCTIONS D To change "Icon" 1. Touch "Icon" on the "Memory Point" screen. 5. Touch the touch−screen button to be edited. "Icon": To select icons to be displayed on the - 2008 Toyota Highlander | Navigation Manual - Page 166
Touch "with Sound" on the "Change Icon" screen. D To change "Quick Access" It is possible to change attributes of the quick access points. the vehicle approaches this point in the direction that has been set. 3. To replace the attribute, touch "Yes". To return to the previous screen, touch "No - 2008 Toyota Highlander | Navigation Manual - Page 167
ADVANCED FUNCTIONS DELETING "Quick Access" D To change "Name" 1. Touch "Name" on the "Memory Point" screen. 1. Touch "Del.". 2. Enter the name using the alphanumeric keys. Up to 24 letters can be entered. 3. Touch " - 2008 Toyota Highlander | Navigation Manual - Page 168
ADVANCED FUNCTIONS DISPLAYING MEMORY POINT NAMES The name of a memory point that may be displayed on the map can be set. D To change "Location" 1. Touch "Location" on the "Memory Point" screen. To show the name, touch "ON" on the "Memory Point" screen. To not show it, touch "OFF". 2. - 2008 Toyota Highlander | Navigation Manual - Page 169
ADVANCED FUNCTIONS - Deleting memory points D To change "Phone #" (telephone number) 1. Touch "Phone #" on the "Memory Point" screen. 1. Push the "MENU . "Delete All": To delete all memory points in the system. 5. To delete the memory point, touch "Yes". To cancel the deletion, touch "No". 99 - 2008 Toyota Highlander | Navigation Manual - Page 170
ADVANCED FUNCTIONS - Registering home If home has been registered, that information can be recalled by using the "Home" touch−screen button on the "Destination" screen. (See " - Destination search by Home" on page 44.) 1. Push the "MENU" button. 2. Touch "My Places". When registration of home is - 2008 Toyota Highlander | Navigation Manual - Page 171
as for a destination search, or display the map of the area to be avoided. (See "Destination search" on page 41.) 5. Set the cursor in the center of the area to avoid, and touch "Enter". 101 - 2008 Toyota Highlander | Navigation Manual - Page 172
area can be edited. 1. Push the "MENU" button. 2. Touch "My Places". 6. Touch either or to change the size of the area to be avoided. 7. Touch "OK". 3. Touch "Edit". INFORMATION D If a destination is input in the area to avoid or the route calculation cannot be made without running through the - 2008 Toyota Highlander | Navigation Manual - Page 173
D To change "Name" 1. Touch "Name" on the "Edit Area to Avoid" screen. 5. Touch the touch−screen button to be edited. "Name": To edit the name of the area to avoid. The names can be displayed on the map. (See page 103.) "Location": To edit area location. (See page 104.) "Area Size": To - 2008 Toyota Highlander | Navigation Manual - Page 174
NAMES OF AREAS TO BE AVOIDED The name of an area to be avoided that may be displayed on the map can be set. D To change "Location" 1. Touch "Location" on the "Edit Area to Avoid" screen. To show the name, touch "ON" on the "Edit Area to Avoid" screen. To not - 2008 Toyota Highlander | Navigation Manual - Page 175
Touch either or to change the size of the area to be avoided. 3. Touch "OK". The previous screen will be displayed. 3. Touch "Delete" on the "My Places" screen. 4. Touch the touch−screen button to be deleted. "Delete All": To delete all registered areas to avoid in the system - 2008 Toyota Highlander | Navigation Manual - Page 176
Points". 1. Push the "MENU" button. 4. Touch the touch−screen button you want to delete. "Delete All": To delete all previous points in the system. 2. Touch "Setup". 3. Touch the items to be set. 5. To delete the point, touch "Yes". To cancel the deletion, touch "No". 4. Touch "OK". The previous - 2008 Toyota Highlander | Navigation Manual - Page 177
D Distance unit Distance unit can be changed. 1. Push the "MENU" button. 2. Touch "Setup" on the "Menu" screen. D OK". 3. Touch "Set Speed" of the "Estimated Travel Time". INFORMATION This function is available only in English or Spanish. To switch language, see "Select language" on page 183 - 2008 Toyota Highlander | Navigation Manual - Page 178
FUNCTIONS D Input key layout INFORMATION D The displayed time to the destination is the approximate driving time that is calculated based on the to 99 hours 59 minutes. Key layout can be changed. 1. Push the "MENU" button. 2. Touch "Setup" on the "Menu" screen. 3. Touch "ABC" or "QWE" - 2008 Toyota Highlander | Navigation Manual - Page 179
ADVANCED FUNCTIONS LAYOUT TYPE D Time zone Time zone can be changed. 1. Push the "MENU" button. 2. Touch "Setup" on the "Menu" screen. " "ABC" type 3. Touch "Change" of "Time Zone". The "Adjust Time Zone" screen will be displayed on the display. " "QWE" type The selected button is highlighted. - 2008 Toyota Highlander | Navigation Manual - Page 180
touch−screen button and current street name on the map screen can be displayed or hidden. 1. Push the "MENU" button. 2. Touch "Setup" on the "Menu" screen. D POI category change (Display POI Icons) Select from among the 6 icons displayed on the "Display POI Icons" top screen, so that setting of the - 2008 Toyota Highlander | Navigation Manual - Page 181
the "Display Building Shapes" feature is turned on, the system will display the building shape on the map screen using a m). To turn the "Display Building Shapes" on: 1. Push the "MENU" button. 2. Touch "Setup" on the "Menu" screen. 5. Touch the category button to be displayed on the "Display POI - 2008 Toyota Highlander | Navigation Manual - Page 182
traffic restriction When the "Traffic Restrict. Notification" feature is turned on, the system notifies you of traffic or seasonal restrictions. To turn the "Traffic Restrict. Notification" on: 1. Push the "MENU" button. 2. Touch "Setup" on the "Menu" screen. Then touch to display page 2 of the - 2008 Toyota Highlander | Navigation Manual - Page 183
off, voice guidance cannot be heard when using the audio/video system. To turn the "Voice Guidance in All Modes" on: 1. Push the "MENU" button. 2. Touch "Setup" on the "Menu" screen. Then touch to display page 2 of the "Setup" screen. D Auto voice guidance When the "Auto Voice Guidance" feature is - 2008 Toyota Highlander | Navigation Manual - Page 184
" on the "Menu" screen. Then touch twice to display page 3 of the "Setup" screen. When the "Pop−up Message" is turned off, following messages are not displayed. This message appears when the system is in the POI mode and the map scale is over 0.5 mile (800 m) or greater. 3. Touch "ON" of "Pop - 2008 Toyota Highlander | Navigation Manual - Page 185
change calibration The current vehicle position mark can be adjusted manually. Miscalculation of the distance caused by tire replacement can also be adjusted. 1. Push the "MENU" button. 2. Touch "Setup of a current vehicle position, see "Limitations of the navigation system" on page 256. 115 - 2008 Toyota Highlander | Navigation Manual - Page 186
FUNCTIONS TIRE CHANGE CALIBRATION The tire change calibration function will be used when replacing the tires. This function will adjust the mis−calculation caused by the circumference difference between the old and new tires. If this procedure is not performed when tires are replaced, the current - 2008 Toyota Highlander | Navigation Manual - Page 187
information setting ...Dealer setting ...D Calendar with memo ...Adding a memo ...Editing a memo ...Memo list ...D Hands−free system (for cellular phone) ... D Speech command system ...174 D Help screen ...177 D Screen adjustment ...178 D Screen setting ...180 D Beep setting ...183 D Select language - 2008 Toyota Highlander | Navigation Manual - Page 188
120.) If "ON" is selected, the system gives maintenance information with the "Information" screen when the system is turned on. (See page 23.) If "OFF" is selected, the "Information" screen is disabled. When the vehicle needs to be serviced, the touch−screen button color will change to orange. 118 - 2008 Toyota Highlander | Navigation Manual - Page 189
oil filter "ROTATION": Rotate tires "TIRES": Replace tires "BATTERY": Replace battery "BRAKE PAD": Replace brake linings "WIPERS": Replace wiper blades "LLC": Replace engine coolant "BRAKE OIL": Replace brake fluid "ATF": Replace ATF "SERVICE": Scheduled maintenance "AIR FILTER": Replace air filter - 2008 Toyota Highlander | Navigation Manual - Page 190
OTHER FUNCTIONS - Dealer setting It is possible to register a dealer in the system. With dealer information registered, route guidance to the dealer is available. 1. Push the "INFO" button. 2. Touch "Maintenance". 3. Touch "Set Dealer" on the "Maintenance" screen. 4. If the dealer has not been - 2008 Toyota Highlander | Navigation Manual - Page 191
OTHER FUNCTIONS D To edit "Dealer" or "Contact" 1. Touch "Dealer" or "Contact" on the "Edit Dealer" screen. D To edit "Location" 1. Touch "Location" on the "Edit Dealer" screen. 2. Enter the name using the alphanumeric keys. Up to 24 letters can be entered. 3. Touch "OK". The previous screen will - 2008 Toyota Highlander | Navigation Manual - Page 192
number) 1. Touch "Phone #" on the "Edit Dealer" screen. It is possible to enter memos for particular dates on the calendar. The system informs you of the memo entry when the system is turned on. (See page 23.) Memos can also be used for route guidance if the memo has been registered with - 2008 Toyota Highlander | Navigation Manual - Page 193
of the mark displayed next to the date. To default the mark color, touch "Delete" on the "Mark color" screen. "Date f": To change the color of the date. To default the date color, touch "Delete" on the "Date color" screen. "Prev. Day": To go to the "Memo" screen of the previous date. "Today": To - 2008 Toyota Highlander | Navigation Manual - Page 194
OTHER FUNCTIONS - Adding a memo If a memo is added, the system informs of the memo entry when the system is started on the memo date. (See page 23.) 1. Push the "INFO" button. 2. Touch "Calendar". 3. Touch the date you want to add a memo on the " - 2008 Toyota Highlander | Navigation Manual - Page 195
period. (See page 126.) 5. Touch the item to be edited. "Memo": To edit a memo. (See " - Adding a memo" on page 124.) "Location": To change a registered location. (See " - Adding a memo" on page 124.) "Enter ": To set the registered location as a destination. (See "Starting route guidance" on page - 2008 Toyota Highlander | Navigation Manual - Page 196
OTHER FUNCTIONS D To display memos for a specified period of time 1. Touch "Period" on the "Memo Search" screen. 5. To delete and/or edit the memo, touch the desired memo button. "Delete All": To delete all the displayed memos. A message will be displayed. 6. To delete, touch "Yes". To cancel the - 2008 Toyota Highlander | Navigation Manual - Page 197
or placed on a cradle. If your cellular phone does not support Bluetoothr, this system can not function. CAUTION While you are driving, do not cellular phone in the car. The temperature indoor may be high and damage the phone. INFORMATION In the following conditions, the system may not function. D - 2008 Toyota Highlander | Navigation Manual - Page 198
the amount of battery charge left. Empty Full It is not displayed while the Bluetoothr is connecting or the phone book data is being transferred. The amount left does not always correspond with the one of your cellular phone. This system doesn't have a charging function. 3 Indicates the receiving - 2008 Toyota Highlander | Navigation Manual - Page 199
the display (behind the seat or in the glove box and console box). D Your cellular phone touches or is covered with metal materials. Leave the Bluetoothr phone on the place where "Blue" indication is displayed. Bluetooth is a trademark owned by Bluetooth SIG, Inc. When you sell your car: A lot of - 2008 Toyota Highlander | Navigation Manual - Page 200
received, including interference that may cause undesired operation. CAUTION Changes or modifications not expressly approved by the party responsible for and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is - 2008 Toyota Highlander | Navigation Manual - Page 201
with at least 20 cm and more between the radiator and person's body (excluding extremities: hands, wrists, feet and legs). Co−location: This . (a) Enter a Bluetoothr phone To use the hands−free system, you need to enter your phone into the system. Once you have registered it, you can make a hands - 2008 Toyota Highlander | Navigation Manual - Page 202
input the Passkey displayed on the screen into the phone. For the operation of the phone, see the manual that comes with your cellular phone. If you want to cancel it, touch "Cancel". 4. Touch "Bluetooth∗" to display the "Bluetooth the system. ∗: Bluetooth is a registered trademark of Bluetooth SIG - 2008 Toyota Highlander | Navigation Manual - Page 203
displayed. This screen appears when the Bluetoothr phone is first connected after the "ENGINE START STOP" switch is in ACCESSORY or IGNITION ON mode. Vehicles without smart key system - When the engine switch is in "ACC" or "ON" position, the selected Bluetoothr phone will be automatically connected - 2008 Toyota Highlander | Navigation Manual - Page 204
connect Bluetoothr manually. Touch "Connect" after enabling the Bluetoothr connection on the phone. the Bluetoothr phone Vehicles with smart key system - If the Bluetoothr phone is disconnected with a poor reception from the Bluetoothr network when the "ENGINE START STOP" switch is in ACCESSORY or - 2008 Toyota Highlander | Navigation Manual - Page 205
FUNCTIONS (b) Call on the Bluetooth r (ii) By phone book You can call by phone book data which phone After you enter the Bluetoothr phone, you can call by using hands−free system. You can call using the 7 methods described below. (i) By dial You can call by inputting the telephone number. This - 2008 Toyota Highlander | Navigation Manual - Page 206
dialed number. The system memorizes up to 5 dialed numbers. If it is more than 5, the oldest number is deleted. This cannot be operated while driving. Touch or push the steering wheel. switch of the 1. Touch "Call Log" to display "Outgoing Calls" screen. D When you call by phone book, the name - 2008 Toyota Highlander | Navigation Manual - Page 207
while driving. D When a telephone number registered in the phone book is received, the name and the number are displayed. D Received calls which you did not answer are also memorized in the system and "Abs." is displayed on the left side of the number. D Received calls which you refused are also - 2008 Toyota Highlander | Navigation Manual - Page 208
you selected from a phone book, dialed numbers and received calls the operation and command of voice recognition, see "Speech command system" on page 174 and "Help screen" on page 177.) screen. 2. Touch the desired number to call. You can change the page by touching "Speed Dial 2" or "Speed Dial - 2008 Toyota Highlander | Navigation Manual - Page 209
by giving a voice tag registered in the phone book. For setting the voice recognition, see "Setting the voice recognition" on page 157. Example: Call DAD You: System: Push the talk switch. "After the beep, please say the name." You: "DAD" System: "DAD chosen, when ready, please briefly push the - 2008 Toyota Highlander | Navigation Manual - Page 210
can call by giving a desired number. D Sending a tone You can send a tone by giving a desired number. You: System: Push the talk switch. "After the beep, please say the number." You: "812387" System: "When ready, please briefly push the talk switch or push the off−hook switch to dial." You: Push - 2008 Toyota Highlander | Navigation Manual - Page 211
OTHER FUNCTIONS (vii) By POI call (c) Receive on the Bluetoothr phone You can call by touching when it is displayed on the screen from Navigation system. (See page 31 for details.) When a call is received, this screen is displayed with a sound. Touch or push the switch of the steering wheel to - 2008 Toyota Highlander | Navigation Manual - Page 212
the Bluetooth r input a Key: Touch "0−9". To transfer the call Touch "Transfer Call". You cannot change from Hands−free call to cellular phone call while driving. When you change of the phone, see the manual that comes with your cellular phone. Touch the desired number to input the key. To hang up - 2008 Toyota Highlander | Navigation Manual - Page 213
number. (ex. 056133p0123w#1:) You can do this operation when you want to operate an answering machine or use a telephone service in bank for example. You can register the phone number and the code number in the phone book. 1. Touch "Speed Tone". 2. Touch the desired switch to send a tone. 143 - 2008 Toyota Highlander | Navigation Manual - Page 214
number from phone book, dialed numbers and received calls. Up to 17 speed dial numbers can be registered. The 6th entry is the speed dial for redialing. Touch "Settings" to display "Settings" screen. 1. Touch "Speed Dial" to display the "Speed Dial Settings" screen. You can change the settings of - 2008 Toyota Highlander | Navigation Manual - Page 215
OTHER FUNCTIONS D Deleting the speed dial individually You can delete "01" − "17" of the speed dial individually. If you delete them all at once, all of 17 numbers are deleted. 4. Touch the desired telephone number. 1. Touch "Delete" of "Speed Dial". 5. Touch the touch−screen button you want to - 2008 Toyota Highlander | Navigation Manual - Page 216
to 6 speed tone numbers can be registered. 1. Touch "Delete All" of "Speed Dial". 1. Touch "Register" of "Speed Tone". 2. Touch "Yes". 2. Use the software keyboard to input the name. 3. Input the number and touch "OK". 146 - 2008 Toyota Highlander | Navigation Manual - Page 217
screen is displayed. Touch "Yes" if you want to overwrite it. 2. Touch the touch−screen button you want to edit. 3. Use the software keyboard to input the name. 147 - 2008 Toyota Highlander | Navigation Manual - Page 218
D Deleting the speed tone individually. You can delete "1" to "6" of the speed tone. If you delete them all at once, all of 6 numbers are deleted. 4. Input the number and touch "OK". 1. Touch "Delete" of "Speed Tone". 2. Touch the touch−screen button you want to delete. 3. Touch "Yes". 148 - 2008 Toyota Highlander | Navigation Manual - Page 219
OTHER FUNCTIONS D Deleting all the speed tone (iii) Setting the volume 1. Touch "Delete All" of "Speed Tone". 1. Touch "Volume" to display the "Volume Settings" screen. 2. Touch "Yes". 2. Touch "−" or "+" to adjust the "Voice Volume" or "Ring Volume". "Voice Volume" ...Adjusting the other party - 2008 Toyota Highlander | Navigation Manual - Page 220
OTHER FUNCTIONS D Automatic volume settings for high speed You can set the volume one step up when the speed is over 80 km/h. (When it is under 70 km/h, previous volume is back.) Each time you touch "Adaptive Volume Control", you can switch on or off. D Initializing the settings You can initialize - 2008 Toyota Highlander | Navigation Manual - Page 221
is received, the Hands−free screen is displayed and you can operate it on the screen. "Icon mode" ...The message is displayed on the upper side of the screen. You can only operate the steering switch. 2. Do the detail settings of the screen and touch "OK". 151 - 2008 Toyota Highlander | Navigation Manual - Page 222
Answer" and "−" or "+" to adjust the waiting time of auto answer within 1 − 60 seconds. Vehicles with smart key system - When the "ENGINE START STOP" switch is in ACCESSORY or IGNITION ON mode and the Bluetoothr is automatically connected, the connection check is displayed. Vehicles without smart - 2008 Toyota Highlander | Navigation Manual - Page 223
FUNCTIONS D Initializing the settings You can initialize the settings. (v) Setting the phone book You can register phone numbers in the phone book. Touch "Default". Touch "Phone Book" to display the "Phone Book Management" screen. Touch "Yes". You can do the detail settings of phone book. 153 - 2008 Toyota Highlander | Navigation Manual - Page 224
appears while transferring. To cancel it, touch "Cancel". If the transferring is interrupted on the way, the phone book data transferred until then can be memorized in the system. 1. Touch "Transfer Data" to display "Select Group" screen. 5. When this screen is displayed, the transfer is completed - 2008 Toyota Highlander | Navigation Manual - Page 225
data. D Editing the name When you don't input the name, the number is displayed. 1. Touch "Register" of "Phone Book". 1. Touch "Name". 2. Touch the desired touch−screen button to edit the phone book. 2. Use the software keyboard to input the name. 3. When you complete the edit, touch "OK". 155 - 2008 Toyota Highlander | Navigation Manual - Page 226
select "No group" or "Group 01" to "Group 19". "No group" is displayed if you don't set the group. 1. Touch "TEL1" or "TEL2". 1. Touch "Group". 2. Input the number and touch "OK". 2. Select the desired group. 3. Select the desired icon. 156 - 2008 Toyota Highlander | Navigation Manual - Page 227
can set the voice recognition. Up to 20 numbers can be registered for the voice recognition. D Adding the data to the phone book You can add data to the phone book. 1. Touch "Add to". 1. Touch "Voice Rec.". 2. Select the data you want to add log data to. 2. Select the phone number and - 2008 Toyota Highlander | Navigation Manual - Page 228
OTHER FUNCTIONS D Editing the data You can edit the registered data. When you also touch "Edit" on this screen, you can edit it. 1. Touch "Edit". 2. Select the data you want to edit. 3. Touch the desired touch−screen button. When you edit the data, touch "OK". 158 - 2008 Toyota Highlander | Navigation Manual - Page 229
Deleting the data You can delete the data. When you release your car, delete all your data on the system. You can also delete it in the following way. 1. Touch "Phone Book". 1. Touch "Delete" of "Phone Book". 2. Select the desired data. 2. Touch the desired touch−screen button. 3. Touch "Delete - 2008 Toyota Highlander | Navigation Manual - Page 230
OTHER FUNCTIONS D Deleting all the phone data 4. Touch "Yes". 1. Touch "Delete All" of "Phone Book". 2. Select the deleting method. "Group Data" ...Deleting all the phone data in group. "All Contact Data" ...Deleting all the phone data. 160 - 2008 Toyota Highlander | Navigation Manual - Page 231
OTHER FUNCTIONS 3. When you select "Group Data", the "Select Group" screen is displayed. You can also delete it in the following way. 4. Select the desired group. 1. Touch "Phone Book". 5. Touch "Yes". 2. Touch "Delete All". 3. Touch "Yes". 161 - 2008 Toyota Highlander | Navigation Manual - Page 232
FUNCTIONS D Registering a group name You can register 20 groups. "No Group", "Group 01" − "Group 19" is registered by default. You can change "Group 01" − "Group 19" into desired names. D Selecting a group icon 1. Touch "Icon". 1. Touch "Register" of "Group Name". 2. Select the desired icon - 2008 Toyota Highlander | Navigation Manual - Page 233
a group name, that group will return to the default setting. (excluding "No Group") 1. Touch "Name". 1. Touch "Delete" of "Group Name". 2. Use the software keyboard to input the name. 2. Select the group you want to delete the name of. 3. Touch "Yes". 163 - 2008 Toyota Highlander | Navigation Manual - Page 234
group name D Deleting the log data You can delete the log data individually or all at once. When you release your car, delete all the data on the system. (a) Individually 1. Touch Name". "Delete All" of "Group 1. Touch "Delete" on the "Log Data" screen. 2. Touch "Yes". 2. Touch "Yes". 164 - 2008 Toyota Highlander | Navigation Manual - Page 235
from using some functions of the Hands−free system. It is useful when you leave your car with the hotel or you don't want others to see the data you registered. When you set or unlock the security, you have to input the security code. Be sure to change - 2008 Toyota Highlander | Navigation Manual - Page 236
but also the memory points in the navigation system, etc. will be deleted. (See "D Initializing the security code" on page 168.) 3. Input the current code. Each time you touch A, an inputted digit is deleted. 4. Input a new code. 1. Touch "Phone Book Lock". 5. Touch "Yes". 2. Touch "Change". 166 - 2008 Toyota Highlander | Navigation Manual - Page 237
locked. D Display of the phone book screen and transferring, registering, editing, deleting the phone book data. D Display of speed dial screen dialed numbers and received numbers. D Display of phone information screen. D Changing the security code. When you set this function, the speed dial - 2008 Toyota Highlander | Navigation Manual - Page 238
phone In case you register more than one Bluetoothr phone, you need to choose a favorite one. 1. Touch "Default". 1. Touch "Settings" to display "Settings" screen. 2. Input the security code and touch "OK". 2. Touch "Select Telephone" to display "Select Telephone" screen. 3. Touch "Yes". 168 - 2008 Toyota Highlander | Navigation Manual - Page 239
Bluetoothr phone is trying to connect, this screen is displayed. Touch "Yes" or "No". Although you can register up to 6 Bluetoothr phones in the system, only one Bluetoothr phone can function at a time. 3. Touch "OK". When the result message is displayed, you can use the Bluetoothr phone. 169 - 2008 Toyota Highlander | Navigation Manual - Page 240
...The name of Bluetoothr phone which is displayed on the screen. You can change it into a desired name. "Bluetooth∗ Device Address" ...The address peculiar to the system. You cannot change it. 2. Touch "Change". 3. When you complete the setting, 1. Select the desired phone and touch "Information - 2008 Toyota Highlander | Navigation Manual - Page 241
peculiar to the system. You can not change it. If you have registered two Bluetoothr phones with the same Device Name or Passkey and you cannot distinguish one from the other, refer to it. ∗: Bluetooth is a registered trademark of Bluetooth SIG. Inc. 2. Use the software keyboard to input the Device - 2008 Toyota Highlander | Navigation Manual - Page 242
Use the software keyboard to input the Device Name. You can input up to 20 characters. 2. Touch "Change" of "Device Name" or "Passkey". ∗: Bluetooth is a registered trademark of Bluetooth SIG. Inc. 4. Input a Passkey with 4 − 8 digits. When you touch A, the inputted number is deleted. 5. When you - 2008 Toyota Highlander | Navigation Manual - Page 243
settings You can initialize the settings. D Deleting a Bluetoothr phone 1. Touch "Default". 1. Touch "Delete" of "Bluetooth∗ Telephone". 2. Touch "Yes". 2. Select the telephone you want to delete and touch "OK". 3. Touch "Yes". ∗: Bluetooth is a registered trademark of Bluetooth SIG. Inc. 173 - 2008 Toyota Highlander | Navigation Manual - Page 244
enables you to operate the navigation system and audio/video system by giving a command. 1. Select the telephone you want to display the information about. 1. Push the talk switch. A beep sounds and on screen message is displayed with an indicator at the top left. 2. When you complete confirming - 2008 Toyota Highlander | Navigation Manual - Page 245
switch and try again. If no command is given, a beep sounds and the indicator disappears 6 seconds later. If the system does not recognize your speech, the system will respond with this message ("System does not recognize this command, please rephrase your command."). Start the operation from the - 2008 Toyota Highlander | Navigation Manual - Page 246
.∗ (ex. say "Woodridge Avenue".) ∗: "Hawaii" or Hawaii area is not covered by the voice recognition. If your home is not registered, you will hear destination", and the system starts searching for a route to your home. (If the destination is already registered, "Add" or "Replace" is displayed on - 2008 Toyota Highlander | Navigation Manual - Page 247
OTHER FUNCTIONS Help screen This system has a function which displays the voice recognition help screen. You can see the command list and operating guide on it. (a) Command List (b) Operating Guide 1. Touch the "Command List" tab on the upper side of the screen and the touch−screen buttons on the - 2008 Toyota Highlander | Navigation Manual - Page 248
can be adjusted depending on the brightness of your surroundings. You can also turn the display off. If your vehicle is equipped with the rear seat entertainment system, the rear screen turns on or off when "Rear" is touched. The screen goes off when "Screen Off" is touched. To turn the display - 2008 Toyota Highlander | Navigation Manual - Page 249
seat entertainment system) You can adjust the color and the tone while the DVD video and video CD are being played. "Color" "R": Strengthens the red color of the screen. "Color" "G": Strengthens the green color position of the headlight switch, the screen changes to either day mode or night mode. - 2008 Toyota Highlander | Navigation Manual - Page 250
OTHER FUNCTIONS Screen setting (a) Automatic transition You can select a function that enables automatic return to the navigation screen from the audio screen. 1. Push the "INFO" button. Select "ON" or "OFF" and then touch "OK". "ON": The navigation screen automatically returns from the audio - 2008 Toyota Highlander | Navigation Manual - Page 251
OTHER FUNCTIONS (b) Switch color You can select a color of touch−screen buttons. (c) Rear system lock (with rear seat entertainment system) If the vehicle is equipped with the rear seat entertainment system, the rear seat entertainment system can be locked to prevent rear passengers from operating - 2008 Toyota Highlander | Navigation Manual - Page 252
points D Areas to avoid D Previous points D Route trace D User selection settings D Phone book data D Dialed numbers and received calls D Speed dial D Bluetoothr phone data D Security code This function is available only when the vehicle is not moving. 1. Touch "Delete personal data". The "Delete - 2008 Toyota Highlander | Navigation Manual - Page 253
You can turn the beep sound off. Select language The language of the touch−screen buttons, pop−up messages and the voice guidance can be changed. 1. Push the "INFO" button. 1. Push the "INFO" button. 2. Touch "Beep Off". "Beep Off" is highlighted. To set the beep sound on, touch "Beep Off" again - 2008 Toyota Highlander | Navigation Manual - Page 254
OTHER FUNCTIONS 184 - 2008 Toyota Highlander | Navigation Manual - Page 255
REAR VIEW MONITOR SYSTEM SECTION REAR VIEW MONITOR SYSTEM Rear view monitor system 7 D Rear view monitor system ...250 249 - 2008 Toyota Highlander | Navigation Manual - Page 256
your Toyota dealer. As the camera has a water proof construction, do not detach, disassemble or modify it. This may cause incorrect operation. If the temperature changes rapidly, such as when hot water is poured on the vehicle in cold weather, the system may not operate normally. D D D D D 250 - 2008 Toyota Highlander | Navigation Manual - Page 257
please consult your Toyota dealer. If you replace the tires, the area displayed on the screen may change. D Area displayed on screen Image is displayed approximately level on screen. " Corners of bumper The area detected by the camera is limited. The camera does not detect objects which are close - 2008 Toyota Highlander | Navigation Manual - Page 258
The area displayed on the screen may vary according to vehicle orientation or road conditions. The rear view monitor system camera is located on the back door as shown in the illustration. The camera uses a special lens. The distance of the image that appears on the screen differs from the actual - 2008 Toyota Highlander | Navigation Manual - Page 259
VIEW MONITOR SYSTEM If a bright light (for example, sunlight reflected off the vehicle body) is picked up by the camera, the smear effect∗ peculiar to the camera may occur. ∗: Smear effect-A phenomenon that occurs when a bright light (for example, sunlight reflected off the vehicle body) is picked - 2008 Toyota Highlander | Navigation Manual - Page 260
REAR VIEW MONITOR SYSTEM 254