3Com 3C16611 User Guide

3Com 3C16611 - SuperStack II Dual Speed Hub 500 Manual

Get 3Com 3C16611 - SuperStack II Dual Speed Hub 500 PDF manuals and user guides
UPC - 662705140582
View all 3Com 3C16611 manuals
Add to My Manuals
Save this manual to your list of manuals

3Com 3C16611 manual content summary:

  • 3Com 3C16611 | User Guide - Page 1
    SuperStack® II Dual Speed Hub 500 12-Port TP (3C16610) and 24-Port TP (3C16611) User Guide INTRODUCTION The SuperStack® II Dual Speed Hub 500 is an easy-to-use, 10/100 autosensing manageable and stackable hub (repeater). It is ideal for users that want the power of Fast Ethernet and the
  • 3Com 3C16611 | User Guide - Page 2
    stack and provides full SNMP and RMON support. Management allows you to configure the way the Dual Speed Hub 500 operates and monitor the way your Dual Speed Hub 500 is described in the user guide that accompanies the Management Module. Refer to the "Products" section in this guide for information
  • 3Com 3C16611 | User Guide - Page 3
    Dual Speed Hub 500, or a power cord of the same type. 8 Type 2 RPS Connector Only connect a 3Com SuperStack II Advanced Redundant Power System (3C16070) to this socket. An appropriate power module and cable is required. For details, follow the installation instructions in the guide that accompany
  • 3Com 3C16611 | User Guide - Page 4
    Console Port Used to connect your management station to the unit for local management; refer to the user guide is not restricted (3Com recommend that you that cables are supported so that they do Instructions" section in this guide. Power Up Use the following sequence to power up the Dual Speed Hub
  • 3Com 3C16611 | User Guide - Page 5
    a public telecommunications system. This can only be achieved using the console port on the unit and an approved modem. France and Peru Si vous entassez l'unité avec les unités SuperStack II, l'unité doit être installée en dessous des unités Dual Speed Hub 500 plus étroites. s Brancher l'unité
  • 3Com 3C16611 | User Guide - Page 6
    Figure 3 Rack Mounting TECHNICAL INFORMATION Related Standards The SuperStack® II Dual Speed Hub 500 has been designed and certified to the Depth Height Weight Mounting 440mm (17.3in.) 230mm (9in.) 44mm (1.7in.) or 1U 3C16610: 2.55kg (5.6lb) / 3C16611: 2.66kg (5.8lb) free standing, or 19in. rack
  • 3Com 3C16611 | User Guide - Page 7
    years +5 Lifetime Limited Warranty The SuperStack II Dual Speed Hub 500 (3C16610 and 3C16611) benefits from 3Com's enhanced +5 Lifetime Limited Warranty. This provides a full 5 years of advanced hardware exchange from your date of purchase in accordance with 3Com's standard terms and conditions
  • 3Com 3C16611 | User Guide - Page 8
    SuperStack II Advanced Redundant Power System World Wide Web Site Access the latest networking information on 3Com Corporation's World Wide Web site by entering our URL into your Internet browser: http://www.3Com.com/ This service features news and information about 3Com products, customer service
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
The SuperStack® II Dual Speed Hub 500 is an easy-to-use, 10/100
autosensing manageable and stackable hub (repeater). It is ideal for
users that want the power of Fast Ethernet and the flexibility to connect
10Mbps devices (workstations and other equipment) in the same hub or
stack.
The Dual Speed Hub 500 has 12 or 24 shielded RJ45 10/100 autosensing
ports on the front panel which can both be used to connect 10BASE-T
(Ethernet) or 100BASE-TX (Fast Ethernet) devices to the hub. There are
two segments (10Mbps and 100Mbps) in the hub, which are linked by a
switch, so your 10Mbps and 100Mbps workstations and equipment can
communicate.
The hub also has two transceiver module slots that can be fitted with a
Management Module, or 3Com 10Mbps or 100Mbps modules to provide
you with additional types of network connection. For information on
what modules can be used, refer to the “
Products
” section in this guide.
The Dual Speed Hub 500 comes with:
■
One power cord for use with the Dual Speed Hub 500
■
Four self-adhesive rubber pads
■
Mounting kit
■
A Warranty Registration card for you to fill out and return
The Dual Speed Hub 500 is suited for office use where it can be free
standing, wall-mounted, or rack-mounted (in a wiring closet or
equipment room).
The unit can be powered either from the AC mains supply, or through
an optional 3Com SuperStack II Advanced Redundant Power System
(3C16070). Contact your supplier for details.
To provide maximum flexibility and expandability, the Dual Speed
Hub 500 can be used with a range of other equipment:
■
Using Cascade Cables, you can connect up to eight Dual Speed
Hub 500 units to form a logical repeater (called a
stack
), providing
up to 208 ports per stack. The 10Mbps and 100Mbps segments in
each hub are connected by the Cascade Cables. Using additional
Hot Swap Cascade Units, you can add resilience to the cascade
connections so that you can remove units at any time without it
affecting communication across the other units in the stack.
■
Using the MDI switch on the front panel, you can connect a
10BASE-T or 100BASE-TX unit or stack to the Dual Speed Hub 500.
■
Using a Dual Speed Hub – PS Hub Cascade Converter Kit, you can
stack Dual Speed Hub 500 units with existing SuperStack II
PS Hubs. The whole stack can be managed as a single entity. The
maximum number of units that you can connect this way to form
a stack is eight.
Refer to the “
Products
” section in this guide for information on obtaining
these products.
I
NTRODUCTION
1
SuperStack® II Dual Speed Hub 500
12-Port TP (3C16610) and 24-Port TP (3C16611)
User Guide
DUA1661-0AAA02