Home » ASRock Manuals » Motherboards » ASRock ALiveNF6G-VSTA » Manual Viewer

ASRock ALiveNF6G-VSTA RAID Installation Guide

ASRock ALiveNF6G-VSTA Manual

View all ASRock ALiveNF6G-VSTA manuals

Add to My Manuals
Save this manual to your list of manuals

ASRock ALiveNF6G-VSTA manual content summary:

ASRock ALiveNF6G-VSTA | RAID Installation Guide - Page 1
NVIDIA RAID Installation Guide 1. NVIDIA BIOS RAID Installation Guide 2 1.1 Introduction to RAID 2 1.2 RAID Configurations Precautions 3 1.3 Create Disk Array 4 2. NVIDIA Windows RAID Installation Guide 8 2.1 NVIDIA Windows RAID Installation Guide for Windows 2000 / XP / XP 64-bit Users
ASRock ALiveNF6G-VSTA | RAID Installation Guide - Page 2
NVIDIA RAID Utility under BIOS environment. After you make a SATA / SATAII driver diskette, press to enter BIOS setup to set the option to RAID mode by following the detailed instruction of the "User Manual" in our support CD or "Quick Installation Guide perform the same work as a single drive
ASRock ALiveNF6G-VSTA | RAID Installation Guide - Page 3
next drive in the array. When any member disk fails, it will affect the entire array. JBOD is not really a RAID, and it does not support fault tolerance. RAID 5 RAID 5 stripes both data and parity information across three or more hard disk drives. Among the advantages of RAID 5configuration include
ASRock ALiveNF6G-VSTA | RAID Installation Guide - Page 4
Power on your system. After adjusting the system BIOS to RAID mode, the below window appears. After rebooting your computer, wait until seconds to press before the window disappears. After you press , the NVIDIA RAID Utility - Define a New Array window appears. By default, RAID Mode is
ASRock ALiveNF6G-VSTA | RAID Installation Guide - Page 5
RAID 0 for example to show you how to use NVRAID RAID Utility to create RAID 0 (Striping). If you plan to use NVRAID RAID Utility to create other RAID arrays, the operation procedures are similar to the steps of creating RAID 0. 5
ASRock ALiveNF6G-VSTA | RAID Installation Guide - Page 6
have to assign the disks. The disks that you enabled from the RAID Config BIOS setup page appear in the Free Disks block. These are the drives that are array disk, A. Tab to the Free Disks section. The first disk in the list is selected. B. Move it from the Free Disks block to the Array Disks
ASRock ALiveNF6G-VSTA | RAID Installation Guide - Page 7
for Serial ATA drives. 0: Controller M: M means Master, S means Slave Serial ATA 1 . 0 . M Channel 1, controller 0, Master 1 . 1 . M Channel 1, controller 1, Master Finally, the Array List window appears, where you can review the RAID arrays that you have set up. Healthy NVIDIA STRIPING 74.53G 7
ASRock ALiveNF6G-VSTA | RAID Installation Guide - Page 8
. Please follow the instructions below according to the OS you install. 2.1 NVIDIA Windows RAID Installation Guide for Windows 2000 / XP / XP 64-bit Users A. Enter NVRAIDMAN RAID driver is built in NVIDIA ALL in one driver provided in our support CD. After you finish the driver installation, you can
ASRock ALiveNF6G-VSTA | RAID Installation Guide - Page 9
motherboard according to the SATA / SATAII HDDs amount you install. Please refer to the RAID functions your motherboard provides in advance and follow the instruction Go to the system BIOS and make sure that the drives that you want to use are RAID enabled. B. Boot to Windows and launch the NVRAIDMAN
ASRock ALiveNF6G-VSTA | RAID Installation Guide - Page 10
D. Click Next and the following screen shot will appear. E. Click the RAID Mode list arrow and select Striping, and leave the "Stripe Size" with its default value as shown in the following screen shot. 10
ASRock ALiveNF6G-VSTA | RAID Installation Guide - Page 11
F. Click Next, and the following screen shot will appear. G. Select the two disks that you want to include in the stripe set. 11
ASRock ALiveNF6G-VSTA | RAID Installation Guide - Page 12
To create a striped array with more disks, select additional disks from the list. H. Click Next and the following screen shot will appear. I. Click Finish and the following screen shot will appear. The RAID 0 is created successfully. C. Initializing NVRAID
ASRock ALiveNF6G-VSTA | RAID Installation Guide - Page 13
B. Double click on Administrative Tools. C. Double click on Computer Management. D. Click on Disk Management. The following screen is displayed. E. The 153.38 GB is for the two disk striped array that was created earlier. To create a partition on it, right click on the Unallocated partition and
ASRock ALiveNF6G-VSTA | RAID Installation Guide - Page 14
D. Deleting a RAID Array NVRAIDMAN can be used to delete an Array. To delete an Array, please do the following. A. Launch the NVRAIDMAN application and right click on the RAID array that you want to delete (assuming that you have a RAID array already created) as shown in the following screen shot.
ASRock ALiveNF6G-VSTA | RAID Installation Guide - Page 15
. A similar process can be applied to delete any array created by NVIDIA RAID. E. Rebuilding a RAID Array Rebuilding is the process of restoring data can rebuild the array using the following steps: A. Go to Windows and run the NVIDIA RAID Management utility. B. Right-click on Mirroring. Then the
ASRock ALiveNF6G-VSTA | RAID Installation Guide - Page 16
D. Click Next. The Disk Selection page appears. E. Select the drive that you want to rebuild by clicking it from the list, then click Next. The Completing the NVIDIA Rebuild Array page appears. 16
ASRock ALiveNF6G-VSTA | RAID Installation Guide - Page 17
the background so as not to affect the performance of the system. Rebuilding Applies Only to RAID 1, RAID 0+1, or RAID 5 Arrays Rebuilding an array works only when using RAID 1, RAID 0+1, or RAID 5. Rebuilding does not apply to RAID 0 and JBOD arrays. Rebuilding applies to a degraded fault tolerant
ASRock ALiveNF6G-VSTA | RAID Installation Guide - Page 18
be completed in a short period of time. 2.2 NVIDIA Windows RAID Installation Guide for Windows Vista / Vista 64-bit Users A. Enter Storage RAID driver is built in NVIDIA ALL in one driver provided in our support CD. After you finish the driver installation, you can create, delete, or rebuild any
ASRock ALiveNF6G-VSTA | RAID Installation Guide - Page 19
Click "Create array". Then you can start to build up RAID. B. Creating RAID Arrays Click Next and the following screen shot will appear. 19
ASRock ALiveNF6G-VSTA | RAID Installation Guide - Page 20
Select a configuration that best suits your storage needs. It is recommended to select "Custom". Click Next. Then, select the type of RAID array to create. You need to choose the RAID Mode first and click Next. Here we take Striping (RAID 0) for example to show you how to use Storage to create
ASRock ALiveNF6G-VSTA | RAID Installation Guide - Page 21
After you decide the RAID Mode, you are allowed to select the Stripe Size. The default value of this item is 64K. Then click Next. Select the disks to add to the new RAID array, and click Next. Select the disk with data to preserve, and click Next. 21
ASRock ALiveNF6G-VSTA | RAID Installation Guide - Page 22
Click Next to confirm that you agree to use the default settings for RAID configurations. Click Finish to complete the steps of creating RAID array. C. Initializing NVRAID Array Disks Now that the two-disk array has been created, it needs to be partitioned and formatted. A. Click on Start → Settings
ASRock ALiveNF6G-VSTA | RAID Installation Guide - Page 23
Right-click on the unallocated partition and select New Simple Volume. Follow the Wizard for setting up and formatting the partition. Once that is done, you can start using the newly created stripped array. 23