Acer S211HL User Manual
Acer S211HL Manual
 |
View all Acer S211HL manuals
Add to My Manuals
Save this manual to your list of manuals |
Acer S211HL manual content summary:
- Acer S211HL | User Manual - Page 1
Acer LCD Monitor User Guide - Acer S211HL | User Manual - Page 2
. Acer Incorporated. All Rights Reserved. Acer LCD Monitor User Guide Original Issue: 03/2010 Changes may be made periodically to the information in this publication without obligation to notify any person of such revisions or changes. Such changes will be incorporated in new editions of this manual - Acer S211HL | User Manual - Page 3
all warnings and instructions marked on the product. Special notes on LCD monitors The following are normal with the LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the power switch and then turn it on again - Acer S211HL | User Manual - Page 4
the power cord from the electrical outlet. Safe listening To protect your hearing, follow these instructions. • Gradually increase the volume until you can hear it clearly and comfortably and without distortion. • After setting the volume level, do not increase it after your ears have adjusted - Acer S211HL | User Manual - Page 5
power supply cord set. If you need to replace the power cord set, make sure that the new power cord meets the following requirements: detachable type, UL listed/CSA certified, type SPT-2, rated 7 A 125 V minimum, VDE approved or its equivalent, 4.6 meters (15 feet) maximum length. Product servicing - Acer S211HL | User Manual - Page 6
instructions. Potentially explosive atmospheres include areas where you would normally be advised to turn off your vehicle engine. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death. Switch off the device near gas pumps at service We at Acer are very - Acer S211HL | User Manual - Page 7
your company's health and safety department. The following section provides tips for more comfortable computer use. Finding your comfort zone Find your comfort zone by adjusting the viewing angle of the monitor, using a footrest, or raising your sitting height to achieve maximum comfort. Observe the - Acer S211HL | User Manual - Page 8
room lighting, poorly focused screens, very small typefaces and low adjusting your display to an awkward viewing angle. • Avoid looking at bright light sources, such as open windows, for extended periods of time. Developing good work habits Develop the following work habits to make your computer - Acer S211HL | User Manual - Page 9
Trade Name: Model Number: SKU Number: LCD Monitor Acer S221HQL/S211HL S221HQL/S211HL 0~9, a ~ z, or A ~ of the restricted substances by weight in homogenous material are: Lead with regard to establishing a framework for the setting of ecodesign requirements for energy-related product. Year - Acer S211HL | User Manual - Page 10
Manufacturer /Importer is responsible for this declaration: Product Name: LCD Monitor Main Model Number: S221HQL/S211HL Series Model Number: S221HQL/S211HL 0~9, a ~ z, A ~ Z or Blank) Name of Responsible Party: Acer America Corporation Address of Responsible Party: 333 West San Carlos - Acer S211HL | User Manual - Page 11
vi LCD pixel statement vii Tips and information for comfortable use vii Declaration of Conformity ix Federal Communications Commission Declaration of Conformity x Unpacking 1 Attaching the base (for selected models) 2 Screen position adjustment 3 Connecting the power cord 3 Power - Acer S211HL | User Manual - Page 12
Troubleshooting 14 VGA mode 14 DVI/HDMI mode 15 - Acer S211HL | User Manual - Page 13
that the following items are present when you unpack the box, and save the packing materials in case you need to ship or transport the monitor in the future. LCD monitor User guide Quick start guide D-sub cable HDMI cable (Optional) AC Power cord DVI cable (Optional) AC Adapter - Acer S211HL | User Manual - Page 14
English 2 Attaching the base (for selected models) Note: Remove the monitor and monitor base from its packaging. Carefully place the monitor face-down on a stable surface -- use a cloth to avoid scratching the screen. 1 Attach the the monitor stand arm to the base. 2 Ensure that the base is locked - Acer S211HL | User Manual - Page 15
The monitor has a universal power supply that allows operation in either 100/120 V AC or 220/240 V AC voltage area. No useradjustment is required. • Plug one end of the AC power cord to the Adapter, and plug the other end into an AC outlet. • For units using 120 V AC: Use a UL-listed cord set, type - Acer S211HL | User Manual - Page 16
plug-and-play. The DDC is a communication protocol through which the monitor automatically informs the host system about its capabilities; for example, supported resolutions and corresponding timing. The monitor supports the DDC2B standard. Connector pin assignment 15-pin color display signal cable - Acer S211HL | User Manual - Page 17
11 TMDS data 1/3 shield 12 NC PIN No. Description 13 NC 14 +5 V power 15 GND (return for +5 V hsync.vsync) 16 Hot-plug detection 17 TMDS data 0- 18 TMDS data 0+ 19 TMDS data 0/5 shield 20 NC 21 NC 22 TMDS clock shield 23 TMDS clock+ 24 DDC TMDS clock- 19-pin - Acer S211HL | User Manual - Page 18
timing table English Mode Resolution 1 640x480 60 Hz 2 VGA 640x480 72 Hz 3 640x480 75 Hz 4 MAC 640x480 66.7 Hz 5 VESA 720x400 70 Hz 6 1280x1024 75 Hz 19 1280x720 60 Hz 20 1280x768 60 Hz VESA 21 1280x768 75 Hz 22 1280x800 60 Hz 23 WXGA 1360x768 60 Hz - Acer S211HL | User Manual - Page 19
both the monitor and computer are powered-OFF. b. Connect the HDMI cable to the computer. 2 Connect the adapter a Connect the AC cord to the adapter. b Connect one end of the adapter to the monitor and the other end to a properly grounded, AC outlet. 3 Turn on the monitor and computer Turn on the - Acer S211HL | User Manual - Page 20
Icon Item Description Power button/ indicator Turns the monitor on/off. Blue indicates power on. Amber indicates standby/power saving mode. / a selection in the OSD. Please refer to "Adjusting the OSD settings" on page 11 for more details. Auto adjust button/Exit If the OSD is active, press - Acer S211HL | User Manual - Page 21
the Auto-adjust button to confirm the mode and exit Acer eColor Management. Features and benefits Main menu Sub menu item Description icon User mode User-defined. Settings can be to read onscreen text. Standard mode Default settings. Reflects native display capability. Graphic mode Movie mode - Acer S211HL | User Manual - Page 22
reference only. Actual product specifications may vary. The OSD can be used for adjusting the settings of your LCD Monitor. Press the Menu key to open the OSD. You can use the OSD to adjust the picture quality, OSD position and general settings. For advanced settings, please refer to following - Acer S211HL | User Manual - Page 23
11 Adjusting the OSD position English 1 Press the Menu key to bring up the OSD. 2 Using the directional keys, select OSD from the onscreen display. Then navigate to the feature you wish to adjust. - Acer S211HL | User Manual - Page 24
12 Adjusting the setting English 1 Press the Menu key to bring up the OSD. 2 Using the / keys, select feature you wish to adjust. Setting from the OSD. Then navigate to the 3 The Setting menu can be used to adjust the screen Menu Language and other important settings. - Acer S211HL | User Manual - Page 25
13 Product information English 1 Press the Menu key to bring up the OSD. 2 Using the / keys, select Information from the OSD. Then the basic information of LCD monitor will show up for current input. - Acer S211HL | User Manual - Page 26
your LCD monitor for servicing, please check the troubleshooting list below to see if you can self-diagnose the problem. VGA mode Problem No picture visible LED status Blue Off Remedy Using the OSD, adjust brightness and contrast to maximum or reset to their default settings. Check the power - Acer S211HL | User Manual - Page 27
15 English DVI/HDMI mode Problem No picture visible LED status Blue Off Remedy Using the OSD, adjust brightness and contrast to maximum or reset to their default settings. Check the power switch. Amber Check if the AC power cord is properly connected to the monitor. Check if the video signal
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
 |
 |
User Guide
Acer LCD Monitor