Airlink AIC1620W Quick Installation Guide
Airlink AIC1620W Manual
 |
View all Airlink AIC1620W manuals
Add to My Manuals
Save this manual to your list of manuals |
Airlink AIC1620W manual content summary:
- Airlink AIC1620W | Quick Installation Guide - Page 1
Quick Installation Guide SkyIPCam1620W Wireless N MPEG4 3GPP Network Camera Model # AIC1620W Ver. 1A - Airlink AIC1620W | Quick Installation Guide - Page 2
monitor them simultaneously, it is recommended that you use a computer with higher performance. This Quick Installation Guide only provides basic instructions. For detailed information, including the instructions of the complimentary software, please refer to the User's Manual on the supplied CD. 1 - Airlink AIC1620W | Quick Installation Guide - Page 3
Section 1 Getting to Know Your Camera Front and Top View Screw Hole* is used to attach the camera stand onto the camera by screwing the screw head of the camera stand into the screw hole of the camera. LED Indicators: Power (left, steady amber light) indicates the camera is powered on. Link (right, - Airlink AIC1620W | Quick Installation Guide - Page 4
held for five seconds, the camera will restore the factory default settings. Antenna Connector Ethernet Cable Connector connects the network cable, which supports the NWay protocol so that the camera can detect the network speed automatically. DC Power Connector connects the AC power adapter, in - Airlink AIC1620W | Quick Installation Guide - Page 5
the IP Camera and connect the other end to one of the LAN ports on your router or switch. NOTE You need to connect the camera to the local area network first in order to configure the wireless settings. After the setup finished, you will be able to disconnect the network cable. 4 - Airlink AIC1620W | Quick Installation Guide - Page 6
Step 2.4 Power up the camera by connecting the supplied power adapter. Step 2.5 Please verify the LED status on the front panel and make sure the camera is on and ready to use now. • Power LED: Solid Amber • Link LED: Flashing Green Section 3 Installing SkyIPCam Utility Step 3.1 Insert the provided - Airlink AIC1620W | Quick Installation Guide - Page 7
Step 3.2 Click on Install Utility and Software when the autorun menu pops up on the screen. Note: If you do not see the autorun menu pops up on the screen, please go to your CD-ROM drive > UltraView folder > run "Setup.exe". Step 3.3 Click Install to install the utility. 6 - Airlink AIC1620W | Quick Installation Guide - Page 8
Step 3.4 Click Finish when installation finishes. Section 4 Configuring the Camera Step 4.1 Open SkyIPCam Utility by double clicking on its icon on your desktop. Step 4.2 Click on Search to find the camera on your network. Select the Camera you wish to configure and click on Link. 7 - Airlink AIC1620W | Quick Installation Guide - Page 9
Note If the Camera you wish to configure does not show up in the utility, make sure the camera is properly connected to the same local network as your computer is, and the Green LED should be on. Click on Search to try again. Step 4.3 When you are prompted for the username and password, enter "admin - Airlink AIC1620W | Quick Installation Guide - Page 10
Step 4.4 The camera viewing window will appear. Click on Setup, then click on Smart Wizard. 1 2 Step 4.5 Enter a name for your camera and a location (i.e. Room 1). Create a password and enter it to Admin Password and Confirm Password. This will change the admin password of the camera. It is - Airlink AIC1620W | Quick Installation Guide - Page 11
to set up email alerts that you can receive in the future, enter your email information here. You can get this information from your Email Service Provider. You can set this up at a later time. Click Next. 10 - Airlink AIC1620W | Quick Installation Guide - Page 12
click on Site Survey and select from the list. Select the Authentication and Encryption, and enter the security Key of your wireless network. This information is stored in your wireless AP/router. Click Next. Note You may contact the manufacturer of your wireless router/AP's to find out its SSID and - Airlink AIC1620W | Quick Installation Guide - Page 13
camera is restarted, unplug the network cable from it. It will take around 1 or 2 minutes for the camera connecting to your wireless router/AP. To make sure the wireless connection is successfully established, open the SkyIPCam Utility and click on Search. If the camera shows up in the list, it is - Airlink AIC1620W | Quick Installation Guide - Page 14
Section 5 Viewing Image Method A > Access Camera from SkyIPCam Utility Step 5.1A Open Airlink101 SkyIPCam Utility, select the camera you wish to connect to and click on Link button. Go to Step 5.3. Method B > Access Camera from Web Browser Step 5. - Airlink AIC1620W | Quick Installation Guide - Page 15
Step 5.3 Enter administrator's username and password of the camera, then click OK. The default username and password are both "admin" if you did not make any change to it at Step 4.5. Step 5.4 Internet Explorer User: If this is the first time for your computer to view image from the web - Airlink AIC1620W | Quick Installation Guide - Page 16
Step 5.5 Click on Run, then you will be able to view the image. Note If you are using Mozilla Firefox or Safari and you are not able to view any image, please make sure you have Java and Quick Time add-ons installed. Step 5.6 To get a clear view of images, you can simply rotate the camera's lens - Airlink AIC1620W | Quick Installation Guide - Page 17
-746-3238 Website: www.airlink101.com * AIC1620W supports most of the mobile devices, but compatibility with every mobile device is not guaranteed. ** Monitoring multiple cameras simultaneously demands high performance computer system. *** Theoretical maximum wireless signal rate derived from IEEE
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
 |
 |
Quick Installation Guide
SkyIPCam1620W
Wireless N MPEG4 3GPP Network Camera
Model # AIC1620W
Ver. 1A