Airlink APO1200 Quick Installation Guide

Airlink APO1200 Manual

Get Airlink APO1200 PDF manuals and user guides View all Airlink APO1200 manuals
Add to My Manuals
Save this manual to your list of manuals

Airlink APO1200 manual content summary:

  • Airlink APO1200 | Quick Installation Guide - Page 1
    Wireless N/A 5GHz 200mW Outdoor AP Model: APO1200 Quick Installation Guide V.1.0
  • Airlink APO1200 | Quick Installation Guide - Page 2
    1. Before You Start Package Contents • APO1200 x 1 • Quick Installation Guide x 1 • CD-ROM (with User Manual and QIG) x 1 • Power Adapter DC24V 0.5A x 1 • PoE injector x 1 • Mounting Kit x 2 System Requirement 9 Web Browser : Internet Explorer (7.0 or above), Firefox, Safari 9 A
  • Airlink APO1200 | Quick Installation Guide - Page 3
    Application in Wireless Network APO1200 is a multiple mode system which can be configured either as a wireless gateway or an access point as desired. It also can be used as a WDS link for Ethernet network expansion. This section depicts different applications on Router AP Mode, AP Mode, WDS Mode,
  • Airlink APO1200 | Quick Installation Guide - Page 4
    2. Hardware Installation 1. Connect N-type antenna to the N-type connector on the rear panel 2. Connect one end of a RJ-45 cable into the AP's PoE connector 3. Connect the opposite end of the RJ-45 cable to the P+DATA OUT port on the Power over Ethernet Injector 4. Connect one end of another RJ-45
  • Airlink APO1200 | Quick Installation Guide - Page 5
    the Access Point from a wired computer. Before the Access Point can be configured, if you connect the AP to your computer directly, you must manually assign a static IP address to your computer's network adapter in the subnet of 192.168.2.x (Refer to Section 7, How to configure TCP/IP settings
  • Airlink APO1200 | Quick Installation Guide - Page 6
    WPA2-PSK. If you select WPA-PSK or WPA2-PSK, make sure your wireless adapters support WPA or WPA2. If your wireless adapters do not support WPA or WPA2, then select WEP. 8. Select the desired Security Type. 9. Select the APO1200's configuration and advanced settings, please refer to User Manual. 5
  • Airlink APO1200 | Quick Installation Guide - Page 7
    4. Configuring for WDS Link Note : 1. The system provide WDS function on Router AP Mode, AP Mode and WDS Mode. 2. WDS Link requires at least 2 APO1200. The Two wire networks(LAN) need the same subnet. 3. The WDS Link needs to be set at same Channel and with same Security Type. 4. Please install and
  • Airlink APO1200 | Quick Installation Guide - Page 8
    3. Enter the desired Channel/Frequency , then click Next button. 4. Click Enable and enter the Remote APO1200's MAC Address. 5. Select the desired Security Type between WDS link, then click Finish button. 6. Wait 35 seconds while the Access Point reboots. Setting Up the Remote APO1200 (Remote Base
  • Airlink APO1200 | Quick Installation Guide - Page 9
    5. Configuring for Client Bride Note : 1. This section will walk you through the steps of sharing (bridging) an internet connection in one building, and extending that same internet to another building. 2. The "Main Base Station" provide Access Point with SSID "Main_AP" 3. The Two wire networks(LAN)
  • Airlink APO1200 | Quick Installation Guide - Page 10
    Setting Up the Client Bridge (Client Station) 1. Follows steps 1-6 (Select "Client Bridge" mode on step 4) in Section 3 Configuring the Access Point. Make sure you change the IP address of the Client Station to be different. 2. Configure the DHCP Server settings to match your demandand then click
  • Airlink APO1200 | Quick Installation Guide - Page 11
    5. Set Client Bridge associate to ESSID "Main_AP" with corrent Pre-shared key. Then click Next button. 6. Select Disable to deactivate Repeater AP. Then click Finish button. 7. Wait 35 seconds while the Access Point reboots. 8. Click Status->Remote AP, the Connection Information should be display.
  • Airlink APO1200 | Quick Installation Guide - Page 12
    is recommended to enable wireless encryption. 2. The examples below are for WEP. If you select WPA-PSK or WPA2-PSK, make sure your wireless adapters support WPA or WPA2. If your wireless adapters do not
  • Airlink APO1200 | Quick Installation Guide - Page 13
    3. Select the desired Security Type. 4. Select the Authentication Type for WEP. 5. Select WEP Key Index and Key, then click Finish. Make sure to copy down the encryption key. 6. Wait 35 seconds while the Access Point reboots. 7. Click Status->Remote AP, the Connection Information should be display.
  • Airlink APO1200 | Quick Installation Guide - Page 14
    7. How to configure TCP/IP settings on your PC Windows XP/2000 1. Go into the Control Panel, double-click the Network Connections icon and then right-click the Local Area Connection icon and then click Properties. 2. Click Internet Protocol (TCP/IP) and then click Properties. Then click on Use the
  • Airlink APO1200 | Quick Installation Guide - Page 15
    Technical Support E-mail: [email protected] Toll Free: 1-888-746-3238 Web Site: www.airlink101.com *Theoretical maximum wireless signal rate derived from IEEE standard 802.11 specifications. Actual
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
Wireless N/A 5GHz 200mW Outdoor AP
Model: APO1200
Quick Installation Guide
V.1.0