Airlink AWLH1201 Quick installation guide

Model: AWLH1201

Quick Installation Guide

This Installation Guide will lead you through the installation of WLAN PCI Adapter and the

software.

To establish your wireless network connection, the following steps should be executed.

1.

Install the software using the installation CD.

2.

Install the WLAN PCI Adapter.

The product is designed to operate in, Windows 98, Windows Me, Windows 2000 and

Windows XP. And the installation procedure for each operating system is about the

same.

Install WLAN PCI Adapter Driver for

Windows 98, ME, 2000 and XP

After inserting in the WLAN PCI Adapter into the computer’s PCI Slot, insert the WLAN

PCI Adapter CD ROM into computer, as the Windows operating system is detecting the

driver, refer to the “D:\Drivers\2k_me_98\Netr8180.inf ” or “D:\ Drivers\xp\Netr8180.inf” in

the box (D:\ will depends on where the CD-ROM drive is located) and click

OK

.

Install WLAN PCI Adapter Utility for

Windows 98, ME, 2000 and XP

1.

When plugging in the WLAN PCI Adapter into the computer’s PCI Slot. Insert the

WLAN PCI Adapter CD ROM into computer and the CD will automatically runs a

setup menu. Then select

Install Software

from the menu. Or proceed manually

using the Windows Start

→

Run

→

type “ D:\Utility\Setup.exe ” in the box (D:\

will depends on where the CD-ROM drive is located) and click

OK

.

2.

The Install Shield tool will help you to setup the WLAN PCI Adapter’s driver.

3.

Restart your computer, then the WLAN PCI Adapter Utility is ready to use.

4.

After the restart, you may check the right side bottom of the computer screen. If

there is an antenna icon

, the WLAN PCI Adapter is ready, otherwise, the icon

will not appear in the taskbar.

Wireless LAN Monitor Utility

With the WLAN PCI Adapter utility, users can configure all the functions provided by the

WLAN Monitor Utility. Double-click the utility icon that appears in the taskbar.

The monitor Utility includes four tabs: Configuration, Link State, Security and Statistics.

In Ad Hoc mode, the Channel and SSID must be the same among stations so that the

computers can communicate within the local LAN properly. Moreover, all connected

computers should have the same net ID and subnet ID, you can follow the procedure

below to check whether you have the same net ID and subnet ID among stations for

Windows 98/ME (Windows 2000 and XP uses similar procedures to check the network

ID):

1.

Right-click on the Network Neighborhood on your desktop and then click on

“Properties”.

2.

In Configuration, click on “TCP/IP -> Wireless PCI Adapter” and then click on

“Properties”.

3.

Click on “IP Address”.

4.

Click on “Specify an IP Address” and make sure having the same net ID and

subnet ID of all the connected computers.

Configuration

¾

Network Type:

If you want to connect with Access Point, please set the mode as” Infrastructure”

mode. If you have more stations and need to link these stations each other without

using an Access Point, set the network type as ” Ad-Hoc” mode.

¾

Channel:

It shows radio channel numbers that used for networking. The Channel number must

be the same among stations, so that computers can communicate within the local

LAN. It can be changed only under the Ad-Hoc mode. If the Mode was set to

Infrastructure mode, this parameter will not be active.

¾

SSID:

SSID is the group name that will be shared by every member of your wireless network .All

the SSID must be the same among stations so that computers can communicate within

the local wireless LAN properly.

The default setting for the SSID will be “ANY”, it will detect the strongest signal of the AP

around you.

¾

Data Rate Select:

You can choose one of the transmission rates as follows, 1Mbps, 2Mbps, 5.5Mbps,

11Mbps, and Auto (it will automatically adjust the transfer rate to have a best connection).

Link State

¾

Site Survey

The screen shows all the messages of Wireless devices around your Wireless PCI

Adapter. The messages of the wireless devices include Network Type, SSID,

BSSID and the Signal.

You can click the Refresh button to find the new wireless devices, and then you can

double-click the BSSID to choose the wireless station that you want to connect.

To display the detail information, click on the “Detail” button.

¾

Other information:

The Signal Strength and Signal Quality will be shown in the screen below under the

Link State of the utility,

Security

You may desire an additional measure of security in your wireless network, which

can be achieved by using the Security function.

¾

Data Encryption

Select WEP for data encryption or No Encryption.

¾

Auth Algorithm:

Open System Authentication algorithm is mostly used. Shard Key Authentication

algorithms use packets with encryption by transferring a challenge text. In order to

choose which authentication algorithm will be used, you must know which one the

AP supports first. Most AP only supports Open System.

¾

Key Setting

You can choose one of the four Keys you typed (Key1~Key4) as the WEP Key.,

and select the key length as 64 bits or 128 bits.

! Caution:

WEP Key needs to be the same for all IEEE802.11b stations.

Follow the steps below to set your WEP:

1.

Select the Encryption type: 64bit or 128bit.

2.

Type WEP Key: If you select 64bit, you must type 10 values in the

following range (0~F, hexadecimal) from Key1 to Key 4 space. Besides, if

you select 128 bit, you must type 26 values (0~F, hexadecimal) in each

WEP Key from Key 1 to Key 4.

3.

Select WEP Key: Select one of WEP Key from Key1 to Key4 for using.

4.

Select the Authentication Type: Open System or Shared Key.

After all the settings are completed, click on Submit button to save the setting.

Statistics

The following screen shows various statistics including the Data Packets,

Management Packets and Rejected Packets in transmitting and receiving status.

You can click the Reset button to reset Statistics Tab.

Checking you connection

1.

Check the icon

that appears in the bottom of the taskbar.

2.

Check if the SSID is the same between the linking stations.

3.

Check if the security key is the same between the linking stations.

4.

Check between the linking stations if it is set on the same the IP network.

Notice: Check the User’s Guide attach in the CD-ROM for detail

information.

Technical support

Email:

[email protected]

Web:

www.airlinkplus.com

P/N: 1907WLB12007050

Airlink AWLH1201 Quick installation guide

Airlink AWLH1201 Manual

Airlink AWLH1201 manual content summary: