Alpine INE-S920HD Owner's Manual (english) - Page 102

Installation, INE-Z928HD/INE-NAV-38 users - installation manual

Page 102 highlights

Installation INE-Z928HD/INE-NAV-38 users To install the INE-Z928HD/INE-NAV-38, refer to the manual in the separately purchased installation kit for each car type. Caution Do not block the unit's fan or heat sink, thus preventing air circulation. If blocked, heat will accumulate inside the unit and may cause a fire. Air ventilation hole Heat sink Rear of the Unit 3 Mounting the GPS Antenna inside the vehicle. 1 Clean the mounting location. 2 Put on the GPS Antenna mounting plate. 3 Mount the GPS Antenna. GPS Antenna Antenna mounting plate • Mount the GPS Antenna on a flat plane of the dash board or rear tray. • Some thermal reflection type or thermal absorption type glass may interrupt high frequency waves. If reception is poor with the antenna installed inside the car, try to mount the antenna outside the car. • Make sure the GPS Antenna is not covered (obstructed) by any metallic surface or object. Caution concerning the installation location 1 Before installing, make sure that the opening and closing of the display will not interfere with operation of the gear shift. (INE-Z928HD/INE-NAV-38 only) Movable Display 2 Angle of installation Install at an angle between horizontal and 30°. Note that installing at an angle outside of this range will result in a loss of performance and possibly damage. 0 -30° 102-EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116

102
-EN
Installation
Caution concerning the installation location
1
Before installing, make sure that the opening and
closing of the display will not interfere with
operation of the gear shift. (INE-Z928HD/INE-NAV-38
only)
2
Angle of installation
Install at an angle between horizontal and 30°. Note
that installing at an angle outside of this range will
result in a loss of performance and possibly
damage.
3
Mounting the GPS Antenna inside the vehicle.
1
Clean the mounting location.
2
Put on the GPS Antenna mounting plate.
3
Mount the GPS Antenna.
Mount the GPS Antenna on a flat plane of the dash board or
rear tray.
Some thermal reflection type or thermal absorption type glass
may interrupt high frequency waves. If reception is poor with
the antenna installed inside the car, try to mount the antenna
outside the car.
Make sure the GPS Antenna is not covered (obstructed) by any
metallic surface or object.
INE-Z928HD/INE-NAV-38 users
To install the INE-Z928HD/INE-NAV-38, refer to the
manual in the separately purchased installation kit for
each car type.
Caution
Do not block the unit’s fan or heat sink, thus preventing
air circulation. If blocked, heat will accumulate inside
the unit and may cause a fire.
Air ventilation hole
Rear of the Unit
Heat sink
<example>
Movable Display
0 -30°
Antenna mounting plate
GPS Antenna