Alpine PSU-300ACD Owners Manual

Alpine PSU-300ACD Manual

Get Alpine PSU-300ACD PDF manuals and user guides View all Alpine PSU-300ACD manuals
Add to My Manuals
Save this manual to your list of manuals

Alpine PSU-300ACD manual content summary:

  • Alpine PSU-300ACD | Owners Manual - Page 1
    so that you can use the product correctly. Alpine Electronics bears no responsibility for problems that arise as a result of failure to follow the instructions in the manuals. ˜ This manual includes a number of symbols that are intended to help you use the product safely, to prevent harm to you
  • Alpine PSU-300ACD | Owners Manual - Page 2
    shock or fire. Do not block vents or heat sinks. Doing so could lead to fire or damage equipment. Use the accessories according to the instructions, and attach them securely. Failing to do so could lead to an accident Forbidden or damage equipment. Do not install the product where it may
  • Alpine PSU-300ACD | Owners Manual - Page 3
    Tools Required Panel Removal Tool Wire Cutters T50 Torx Sockets 8mm 10mm Extension Cordless Power Drill Honda Accord ˜ 3/12 Phillips Screwdriver Ratchet Step Drill Bit Accessory List Amplifier Assembly T-Harness Main Harness (10) Cable Ties RCA Adapters Power Cable Lock Washers ½" Wafer
  • Alpine PSU-300ACD | Owners Manual - Page 4
    Factory Equipment Removal Process 1 Use a panel removal tool to remove the center console side covers. Honda Accord ˜ 4/12 2 Remove the push-to-start button panel by pulling the panel towards the back. PUSH AUTO 3 Remove the passenger side dash cover above the glove box by pulling towards the
  • Alpine PSU-300ACD | Owners Manual - Page 5
    Honda Accord ˜ 5/12 Factory Equipment Removal Process (continued) 7 Remove the passenger side under dash cover by pulling down. 8 Remove the glovebox by extracting (3) Phillips Panhead screws on top and (2) 8mm screws on the bottom. 9 Release the shifter panel by pulling up. 10 Press the
  • Alpine PSU-300ACD | Owners Manual - Page 6
    Honda Accord ˜ 6/12 Factory Equipment Removal Process (continued) 13 Extract (4) 14mm screws from the passenger side seat. 14 Tilt the passenger seat towards the back to reveal (3) connectors, disconnect and remove the seat. Front of Vehicle
  • Alpine PSU-300ACD | Owners Manual - Page 7
    Honda Accord ˜ 7/12 Installation 1 Connect the power cable to the Positive (+) battery terminal at the fuse block in the engine compartment. Note: The negative terminal should remain disconnected unit the installation is completed. 2 Route the cable towards the passenger side as shown below. 3
  • Alpine PSU-300ACD | Owners Manual - Page 8
    Honda Accord ˜ 8/12 Installation (continued) 7 Locate the Active Noise Cancelling module behind the passenger side vent and disconnect it. Note: skipping this step will cause the subwoofer to emit unwanted engine rumble. 8 Route the main harness along the side on the center console to the radio
  • Alpine PSU-300ACD | Owners Manual - Page 9
    OEM Head Unit Wiring Diagram To Vehicle Connectors Power/Speaker 24-pin Gray Connector OEM T-HARNESS ADAPTER Front Speakers 4-PIN WHITE CONNECTOR Rear Speakers 4 PIN BLACK CONNECTOR WHITE/GRAY White Connector GREEN/PURPLE Black Connector BROWN/ORANGE Red Connector TO OEM HEAD UNIT Front Rear
  • Alpine PSU-300ACD | Owners Manual - Page 10
    Honda Accord ˜ 10/12 Aftermarket Head Unit Wiring Diagram To Vehicle Connectors Power/Speaker 24-pin Gray Connector OEM T-HARNESS ADAPTER To 3rd party wire harness and radio replacement interface * Wire Harness and Interface sold separately Front Speaker 4-PIN WHITE CONNECTOR Rear Speakers 4-
  • Alpine PSU-300ACD | Owners Manual - Page 11
    BLACK To Chassis Ground BROWN/ORANGE L R Red RCA Adapter For a detailed Alpine Restyle head unit wiring diagram refer to it's corresponding installation manual. RED To Battery Cable HEAD UNIT POWER PACK KTP-445U To Vehicle's Battery POSITIVE (+) Terminal POWER PACK AMPLIFIER KTP-445U Amplifier
  • Alpine PSU-300ACD | Owners Manual - Page 12
    Honda Accord ˜ 12/12 Troubleshooting Guide Symptom 1 System will not turn on 2 Volume the speaker, loose pins, disconnected terminals etc.. Disconnect the battery and re-connect after 5 minutes. If problem is not solved, the vehicle will have to be taken to a Honda dealer. Connect the Remote Turn-
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
Honda Accord
±
1/12
Honda Accord
PSU-300ACD Sound System Upgrade
Installation Manual
±
Model: 4-Door
±
Model Year: 2018 – UP
*Not compatible with EX-L and Touring Models
Introduction
±
Congratulations on purchasing the PSU-300ACD. This installation manual is designed to take you through the
step-by-step installation of the PSU-300ACD into a 2018 - Up Honda Accord. Please familiarize yourself with
the owner’s manual and if you still have additional questions please call 1-800-TECH-101.
Note
±
Design and specifications are subject to change without notice for improvement.
To Ensure Safe Use, Always Follow These Precautions
±
The installation of this product requires specialized skills and experience. We recommend that you have the
product installed by an Alpine authorized dealer.
±
Before you use this product, be sure to carefully read this installation manual and the separate user’s manual
so that you can use the product correctly. Alpine Electronics bears no responsibility for problems that arise as
a result of failure to follow the instructions in the manuals.
±
This manual includes a number of symbols that are intended to help you use the product safely, to prevent
harm to you and others, and to protect against damage to property. These symbols and their meanings are
listed below. Make sure you fully understand these symbols before you begin reading the main text.
Explanations of Injury and Damage That May Result from Incorrect Use
Warning
Ignoring the content marked by this indication and using the product incorrectly may
lead to death or serious injury.
Caution
Ignoring the content marked by this indication and using the product incorrectly may
lead to injury or property damage.
Honda
Model
Year
Accord
2018 – UP
* The specified vehicles have been tested and have met compatibility specs at the time of testing. Compatibility is
not guaranteed if the manufacturer has made production changes to the listed vehicles above.
Warning: Before you begin, remove the ground wire from the NEGATIVE (-)
terminal of the battery. Failing to do so can lead to electric shock, injury or damage
to equipment.