American Standard Cadet-3 Installation Instructions
American Standard Cadet-3 - 3011.016.165 Tropic Round Front Toilet Bowl Manual
 |
UPC - 033056671351
View all American Standard Cadet-3 manuals
Add to My Manuals
Save this manual to your list of manuals |
American Standard Cadet-3 manual content summary:
- American Standard Cadet-3 | Installation Instructions - Page 1
INSTALLATION INSTRUCTIONS CARE AND MAINTENANCE Tropic Cadet®3 2-piece Round Front, Elongated, Right Height™ Toilets Models 2455 / 2457 / 2459 / 2791 Triumph Cadet®3 2-piece Round Front, Elongated, Right Height™ Toilets Models 2490 / 2491 / 2492 Thank you for selecting American Standard - the - American Standard Cadet-3 | Installation Instructions - Page 2
SEAT Install toilet seat in accordance with manufacturer's directions. 9b 9a Before continuing, determine the type of water supply connecation you have from the chart below and use the appropriate assembly parts required to properly reconnect the water supply. DO NOT use plumber's putty to seal - American Standard Cadet-3 | Installation Instructions - Page 3
(replace with a new flapper). IF FILL VALVE WON'T TURN ON OR SHUT OFF or REFILL OF TANK WATER IS SLOW after valve has been in use for some time, Fluidmaster Model 242 Replacement Seal may be needed. Go to our website at www.fluidmaster.com for more solutions to toilet problems. For troubleshooting - American Standard Cadet-3 | Installation Instructions - Page 4
. (see Step 13) Poor or sluggish flush c. Flush valve chain too loose or disconnected. d. Sand or debris lodged in water control. a. Bowl water level too low. Toilet leaks Toilet does not shut off b. Supply valve partly closed. c. Partially clogged trapway and/or drain pipe and/or vent
-
1 -
2 -
3 -
4
 |
 |
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Adjustable Wrench
Sealant
Tape Measure
Hacksaw
Wax Ring/Gasket
Flexible Supply Tube
Closet Bolts
Carpenters Level
1
REMOVE OLD TOILET
a.
Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b.
Disconnect and remove supply line. NOTE:
If replacing valve, first shut off main water supply!
c.
Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d.
Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE:
Mounting surface must be clean and level
before
new toilet is installed!
S
AV
E
F
O
R
F
U
T
U
R
E
U
S
E
3
2
CLOSET FLANGE
CLOSET BOLTS
7301102-100 Rev. K
A
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2011
NOTE:
Pictures may not exactly define contour of china and components.
Tropic Cadet
®
3 2-piece Round Front,
Elongated, Right Height
™
Toilets
Models 2455 / 2457 / 2459 / 2791
Triumph Cadet
®
3 2-piece Round Front,
Elongated, Right Height
™
Toilets
Models 2490 / 2491 / 2492
FINISHED WALL
FINISHED
FLOOR
SUPPLY
AS
REQ'D.
12"
(305mm)
WAX RING
SEALANT
5
4
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage), and
install wax ring evenly around waste flange (horn), with
tapered end of ring facing toilet. Apply a thin bead of
sealant around toilet base.
POSITION TOILET ON FLANGE
a.
Unplug floor waste opening and install toilet on closet flange so bolts project
through mounting holes.
b.
Loosely install retainer washers and nuts. Side of washers marked "THIS
SIDE UP"
must
face up!
CLOSET
BOLT
NUT
TAPERED
WASHER
FLANGE
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
Thank you
for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly,
please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your
installation conforms to local codes.
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90
°
, and slide
into place 6" (152 mm) apart and parallel to wall.
!
For 4007 Tanks:
12" (305mm)
ROUGHING-IN DIMENSIONS:
NOTE:
Distance from wall to closet flange centerline must be as listed below: