Asus P5LD2 SE Motherboard Installation Guide - Page 47

Internal connectors

Get Asus P5LD2 SE PDF manuals and user guides View all Asus P5LD2 SE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

2.7.2 Internal connectors 1. Floppy disk drive connector (34-1 pin FLOPPY) This connector is for the provided Floppy Disk Drive (FDD) signal cable. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. Pin 5 on the connector is removed to prevent incorrect cable connection when using a FDD cable with a covered Pin 5. P5LD2 SE Top:Line In Center:Line Out Below:Mic In R FLOPPY NOTE: Orient the red markings on the floppy ribbon cable to PIN 1. PIN 1 P5LD2 SE Floppy Disk Drive Connector 2. ICH7 Primary IDE connector (40-1 pin PRI_IDE) This connector is for an Ultra DMA 133/100/66 signal cable. The Ultra DMA 133/100/66 signal cable has three connectors: a blue connector for the primary IDE connector on the motherboard, a black connector for an Ultra DMA 133/100/66 IDE slave device (optical drive/hard disk drive), and a gray connector for an Ultra DMA 133/100/66 IDE master device (hard disk drive). If you install two hard disk drives, you must configure the second drive as a slave device by setting its jumper accordingly. Refer to the hard disk documentation for the jumper settings. • Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable. • Use the 80-conductor IDE cable for Ultra DMA 133/100/66 IDE devices. P5LD2 SE Top:Line In Center:Line Out Below:Mic In R NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. P5LD2 SE IDE Connector ASUS P5LD2 SE PIN 1 PRI_IDE 2-25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
ASUS P5LD2 SE
2-25
2.
ICH7 Primary IDE
connector (40-1 pin PRI_IDE)
This connector is for an Ultra DMA 133/100/66 signal cable. The Ultra
DMA 133/100/66 signal cable has three connectors: a blue connector
for the primary IDE connector on the motherboard, a black connector
for an Ultra DMA 133/100/66 IDE slave device (optical drive/hard
disk drive), and a gray connector for an Ultra DMA 133/100/66 IDE
master device (hard disk drive). If you install two hard disk drives,
you must configure the second drive as a slave device by setting its
jumper accordingly. Refer to the hard disk documentation for the
jumper settings.
•
Pin 20 on the IDE connector is removed to match the covered hole
on the Ultra DMA cable connector. This prevents incorrect insertion
when you connect the IDE cable.
•
Use the 80-conductor IDE cable for Ultra DMA 133/100/66 IDE
devices.
PRI_IDE
PIN
1
NOTE:
Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
P5LD2 SE IDE Connector
P5LD2
SE
2.7.2 Internal connectors
1.
Floppy disk drive
connector (34-1 pin FLOPPY)
This connector is for the provided Floppy Disk Drive (FDD) signal
cable. Insert one end of the cable to this connector, then connect the
other end to the signal connector at the back of the floppy disk drive.
Pin 5 on the connector is removed to prevent incorrect cable connection
when using a FDD cable with a covered Pin 5.
FLOPPY
NOTE:
Orient the red markings on
the floppy ribbon cable to PIN 1.
PIN 1
P5LD2 SE Floppy Disk Drive Connector
P5LD2
SE