Asus RS700-E11-RS12U 1U Height Full Extension Ball bearing Type Rail Kit Instr
Asus RS700-E11-RS12U Manual
View all Asus RS700-E11-RS12U manuals
Add to My Manuals
Save this manual to your list of manuals |
Asus RS700-E11-RS12U manual content summary:
- Asus RS700-E11-RS12U | 1U Height Full Extension Ball bearing Type Rail Kit Instr - Page 1
(Pre-installed) For 9.5 Square hole frame : Install slide rail as usual. Ⓗ7.1 Round Hole For 7.1 Round hole frame : Please refer to the manual:Replacing the suitable pin. ⒾM5-Bracket screw Rear Bracket Ⓘ Front Bracket Ⓗ Ⓖ Ⓖ Ⓗ Ⓘ ⒶM4x4L-P0.7 Ⓑ#6-32X4L ⒸRound hole pin Ⓓ#10-32X13L ⒺM5X20-P0 - Asus RS700-E11-RS12U | 1U Height Full Extension Ball bearing Type Rail Kit Instr - Page 2
R 5 Insert the chassis to complete the installation ➊➋ Pull the middle rails fully extended in lock position, ensure ball bearing retainer is located at the front of the middle rails. ➌ Horizontally insert the chassis into middle-outer rails. ➍ When hit a stop, please pull/push the blue release tab
➋
Electronic File
inner rail
middle rail
outer rail
Click!
Click!
➊
Pull tab forward and take out inner rail.
➋
Push (a) and slide middle rail back.
➎
Please repeat installation steps for the other side.
⑤
Please repeat the detached steps for the other side.
Copyright © 2021 King Slide. All Rights Reserved
White
(a)
➊
Key Hole
.
①-④
➋
Screw Hole.
Pull
②
lide inner rail
forward to remove inner rail.
Pull the latch upward and
remove the keyhole from
standoff and s
Click
Front bracket
Rear bracket
Front bracket
➊
➍
Click
➌
➋
Push
①
Loosen screw.
→
Click
Pull.
Ⓗ
7.1
Round Hole
Ⓖ
9.5
(
)
Square Hole
Pre-installed
Ⓘ
M
Bracket screw
5-
Front Bracket
For 9.5 Square hole frame : Install slide rail as usual.
3)
Check hole type on rack post. Choose
suitable pin of bracket to install if needed.
Rear Bracket
For 7.1 Round hole frame
Please refer to the
manual
Replacing the suitable pin.
:
:
Ⓐ
M4x4L-P0.7
Ⓑ
6-32X4L
Push
Push
Rear bracket
①
②
③
④
Please choose
or
screw for inner rail
depends on chassis spec.
Ⓐ
Ⓑ
Ⓖ
Ⓗ
Ⓘ
Ⓖ
Ⓗ
Ⓘ
Push
●
i
Detach nner rail from standoff
●
i
●
b
r
p
Detach
racket from
ack
ost
●
b
r
p
SCREW SACK
Ⓐ
M4x4L-P0.7
Inner rail
Ⓑ
#6-32X4L
Inner rail
Ⓒ
Round hole pin
ForØ7.1Round Hole
Ⓓ
#10-32X13L
For#10-32 Thread Hole
Ⓔ
M5X20-P0.8
For Shipping
Ⓕ
M5x13.5L-P0.8
For Shipping
①
②
①
②
③
④
Install the inner rail onto the chassis
Install
the
inner
rail
onto
the
chassis
3
Fix the outer rail/bracket assembly to the frame
4
Remove the inner rail
Check hole type on rack post
1
2
R