Asus RS720-E11-RS12U 15U Height Full Extension Ball bearing Type Rail Kit Inst
Asus RS720-E11-RS12U Manual
View all Asus RS720-E11-RS12U manuals
Add to My Manuals
Save this manual to your list of manuals |
Asus RS720-E11-RS12U manual content summary:
- Asus RS720-E11-RS12U | 15U Height Full Extension Ball bearing Type Rail Kit Inst - Page 1
(Pre-installed) For 9.5 Square hole frame : Install slide rail as usual. Ⓒ 7.1 Round Hole For 7.1 Round hole frame : Please refer to the manual:Replacing the suitable pin. Ⓘ M5 Bracket Screw (Pre-Installed) Front bracket ⒼⒸ Rear bracket ⒼⒸ Ⓘ 3 Install the inner rail onto the chassis ● Detach - Asus RS720-E11-RS12U | 15U Height Full Extension Ball bearing Type Rail Kit Inst - Page 2
R 5 Insert the chassis to complete the installation ➊➋ Pull the middle rails fully extended in lock position, ensure ball bearing retainer is located at the front of the middle rails. ➌ Horizontally insert the chassis into middle-outer rails. ➍➎ When hit a stop, please pull/push the blue release
➋
inner rail
middle rail
outer rail
Click!
Click!
➊
Pull tab forward and take out inner rail.
➋
Push and slide middle rail back.
*
Please repeat installation steps for the other side.
*
Please repeat the detached steps for the other side.
Copyright © 2021 King Slide. All Rights Reserved
Remove the inner rail
Check hole type on rack post
Install the inner rail onto the chassis
Fix the outer rail/bracket assembly to the frame
●
i
Detach nner rail from standoff
●
i
●
b
r
p
Detach
racket from ack
ost
●
b
r
p
1
2
3
4
White
➊
Key Hole
.
①-⑥
➋
Screw Hole.
Pull
②
lide inner rail forward to
remove inner rail.
Pull the latch upward and remove the keyhole
from standoff and s
Front bracket
→
Click
Pull.
Front bracket
**Check hole type on rack post. Choose suitable pin of
bracket to install if needed.
Rear bracket
Ⓐ
M4x4L-P0.7
Ⓑ
6-32x4L
Rear bracket
⑥
⑤
②
④
①
③
Front bracket
➎
➍
➏
Push
Rear bracket
➊
➋
Push
Push
Push
➌
Ⓖ
Ⓘ
9.5
(
)
7.1
5
Square Hole
Round Hole
Pre-installed
(Pre-Installed)
Ⓒ
M
Bracket Screw
For 9.5 Square hole frame : Install slide rail as usual.
For 7.1 Round hole frame
Please refer to the manual
Replacing the suitable pin.
:
:
①
②
③
①
Loosen screw.
Choose by
chassis spec
①
②
③
④
Ⓖ
Ⓒ
Ⓘ
Ⓖ
Ⓒ
Ⓐ
M4x4L-P0.7
Inner rail
Ⓑ
#6-32x4L
Inner rail
Ⓒ
Round hole pin
For Ø7.1 Round Hole
Ⓓ
#10-32x13L
For #10-32 Thread Hole
Ⓔ
M5x9.0L-P0.8
For Shipping
Ⓕ
M3x4.0L-P0.5
For CMA BKT
SCREW SACK
Electronic File
R