Asus Terminator P-III E787 MANUAL TERMINATOR English
Asus Terminator P-III Manual
 |
View all Asus Terminator P-III manuals
Add to My Manuals
Save this manual to your list of manuals |
Asus Terminator P-III manual content summary:
- Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 1
® Terminator Barebone System Installation Guide - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 2
A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Copyright © 2001 ASUSTeK COMPUTER INC. All Rights Reserved. Product Name: Terminator Barebone System Manual Revision - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 3
Center, Building 2 Newark, CA 94560, USA +1-510-608-4555 [email protected] Technical Support Fax: +1-510-608-4555 BBS: +1-510-739-3774 Email: [email protected] WWW: www.asus.com FTP: ftp.asus.com.tw/pub/ASUS ASUS COMPUTER GmbH (Europe) Marketing Address: Fax: Email: Harkortstr. 25, 40880 - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 4
. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer's instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 5
a CPU 16 2.4 Install System Memory 18 2.5 Install a Hard Disk Drive 19 2.6 Install a CD-ROM Drive 21 2.7 Install a Modem Riser Card 23 2.8 Install a PCI Expansion Card 24 2.9 Re-connect Cables 25 2.10 Replace the Cover 26 2.11 Connect External Devices 28 Chapter 3: Motherboard Information - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 6
included in the standard system package. 1) System Chassis 2) Motherboard 3) Switching Power Supply 4) 1.44MB Floppy Disk Drive 5) CD-ROM Drive (optional) 6) 56K PCI Modem Card (optional) 7) Support CD with Drivers and Utilities 8) Installation Guide NOTE If you are assembling the system by yourself - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 7
Introduction You are reading the ASUS Terminator Barebone System Installation Guide. This guide provides general information and installation instructions about the Terminator Barebone System. "About This Guide" contains an introduction on the contents of this document that include target audience - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 8
barebone system through illustrated step-by-step instructions. 4. Chapter 3: Motherboard Information This chapter gives information about the CUSC motherboard that comes with the ASUS Terminator Barebone System.This chapter includes the motherboard layout, jumper settings, and connector locations - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 9
System Introduction Chapter 1 This chapter gives a general description of the ASUS Terminator barebone system. It includes introduction on the front and rear panel features, and the internal features. ASUS Terminator Barebone System 9 - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 10
1.1 Front Panel Features The ASUS Terminator barebone system is composed of the ASUS CUSC motherboard, a power supply, and a floppy disk drive in the ASUS TriOptix form factor chassis. The following figures show the front panel features. NOTE The CD-ROM drive and modem card are optional items and - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 11
1.2 Rear Panel Features The rear panel of the ASUS Terminator barebone system includes the standard PC99 I/O connectors for external devices, power supply socket, and CAUTION! Setting the switch to 115V in a 230V environment will seriously damage the system. ASUS Terminator Barebone System 11 - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 12
you can install the other required components to get the system running. Two 5.25" 3.5" HDD 3.5" Floppy Drive Bays Drive Bay Drive Power Supply Modem Card Motherboard USB/audio Board 12 Chapter 1: System Introduction - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 13
Chapter 2 This chapter tells how to install components into the barebone system through illustrated step-by-step instructions. Basic Installation ASUS Terminator Barebone System 13 - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 14
2.1 Remove the Cover The chassis cover is secured by a thumbscrew located on the rear panel. Follow these steps to remove the chassis cover. 1. Turn the captive thumbscrew counter-clockwise to release the cover. You don't have to remove the thumbscrew from the chassis. Thumbscrew 2. Place your hand - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 15
is not necessary to completely detach the drive frame from the chassis when installing components. 2. Carefully lay the drive frame alongside the main chassis frame. ASUS Terminator Barebone System 15 - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 16
2.3 Install a CPU The ASUS CUSC motherboard that comes installed in the chassis has a Socket 370 that supports an Intel Pentium III/Celeron processor. Follow these steps to install a CPU. 1. Locate the CPU socket on the motherboard. CPU Fan Connector (CPU_FAN) CPU Socket 370 2. Unlock the socket by - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 17
the motherboard. Refer to the picture in step 1. CPU Fan Cable WARNING! The CPU fits only in one orientation. DO NOT force the CPU into the socket to prevent bending the pins and damaging the CPU. If the CPU does not fit completely, check its orientation or check for bent pins. ASUS Terminator - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 18
Dual Inline Memory Module (DIMM) sockets. The sockets support up to 1GB system memory using PC133-compliant Synchronous Dynamic Random Access Memory (SDRAM) DIMMs. Follow these steps to install a DIMM. 1. Locate the DIMM sockets on the motherboard. DIMM Sockets 2. Unlock a DIMM socket by pressing - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 19
until its screw holes align with the holes on the bay. 4. Secure the HDD with two screws on each side of the bay. HDD Screws ASUS Terminator Barebone System 19 - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 20
to Pin 1 Power Cable (HDD) 7. Connect the other end of the IDE ribbon cable to the primary IDE connector (blue connector labeled IDE1) on the motherboard. Primary IDE Connector (IDE1) 20 Chapter 2: Basic Installation - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 21
2.6 Install a CD-ROM Drive A CD-ROM drive is an optional item in the Terminator barebone system. Refer to the instructions in this section if you acquired a model without a CD-ROM. Follow these steps to each side of the bay. 5.25-inch Drive Bay CD-ROM Screws ASUS Terminator Barebone System 21 - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 22
to Pin 1 Power Cable (P6) 8. Connect the other end of the IDE ribbon cable to the secondary IDE connector (black connector labeled IDE2) on the motherboard. 9. Connect the other end of the audio cable to the black 4-pin connector labeled CD on the - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 23
Riser Card The motherboard includes an AMR slot that supports a modem riser card. The modem riser card is an optional item in the Terminator barebone system. Refer to the instructions in this section if a Telephone Set Modem Riser Card Installed on the AMR Slot ASUS Terminator Barebone System 23 - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 24
2.8 Install a PCI Expansion Card The motherboard has two 32-bit PCI slots (one shared with AMR slot). If you wish to install a PCI card, refer to the instructions in this section. The figure on the right shows a sample PCI network card that you can install on the PCI slot. Follow these steps to - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 25
Connect the power switch and power LED cables to their respective leads in the PANEL connector on the motherboard. 2. Connect the HDD LED cable to the 2-pin lead marked IDELED. 3. Connect the Line Out/Mic Lead (for Line Out Cable) MIC2 Lead (for Microphone Cable) ASUS Terminator Barebone System 25 - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 26
2.10 Replace the Cover After you have installed all the internal components and you have connected all the necessary cables, you are now ready to put the system back together. Follow these steps to re-assemble the system. 1. With the chassis lying on its side, hook the swivel edge of the drive - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 27
Firmly push the cover to ensure that it is fully engaged to the chassis. 7. Lock the cover with the captive thumbscrew on the rear panel. ASUS Terminator Barebone System 27 - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 28
2.11 Connect External Devices The figure below shows the specific connectors and devices that you can connect to the rear panel ports. Serial PS/2 KB VGA Line Out Line In Mic RJ-45 Game/MIDI PS/2 Mouse AC Parallel USB 28 Chapter 2: Basic Installation - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 29
Chapter 3 This chapter gives information about the CUSC motherboard that comes with the ASUS Terminator Barebone System.This chapter includes the motherboard layout, jumper settings, and connector locations. It also includes information on the USB/ audio board located on the front panel. In cases - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 30
Refer to the layout below to locate specific motherboard components. The motherboard has a side connector for a detachable extension module) ® Line Out Socket 370 Line In Mic In CPU_FAN RJ-45 CH_FAN LANLED ASUS Mozart USB T: Port0 B: Port1 USBPWR1 CD FLOUT AUX MIC2 PCI Slot 1 Audio - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 31
including two USB, headphone, and microphone connectors. Front Panel Connectors USB T: Port0 B: Port1 USB2P UAEX ® LOUT LO2 MIC MIC2 Connect to USB1 Connector on the Motherboard Connect to FLOUT Lead on the Motherboard Connect to MIC2 Lead on the Motherboard ASUS Terminator Barebone System 31 - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 32
to send to the CPU, DRAM, and PCI buses. JP0 CUSC External Clock (BUS) Frequency Selection CPU 1 1 1 (Default) 66. to allow wake up from S1 sleep state (CPU stopped; RAM refreshed; system running in low up from S3 state (no power to CPU; RAM in slow refresh; power supply in - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 33
the battery. 5. Plug the power cord and turn ON the computer. 6. Hold down the key during the boot process and enter BIOS setup to re-enter data. CUSC ® CLRTC CR2032 3V Lithium Cell CMOS Power CUSC Clear RTC RAM Short solder points to Clear CMOS ASUS Terminator Barebone System 33 - Asus Terminator P-III | E787 MANUAL TERMINATOR English - Page 34
+5V Ground PWR Switch* Ground ExtSMI# SMI Lead PLED Power LED +5 V TB_LED +5 V Message LED * Requires an ATX power supply. CUSC System Panel Connectors 34 Chapter 3: Motherboard Information
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
 |
 |
Barebone System
®
Terminator
Installation Guide