Behringer CP35 ATTENUATORS Quick Start Guide
Behringer CP35 ATTENUATORS Manual
 |
View all Behringer CP35 ATTENUATORS manuals
Add to My Manuals
Save this manual to your list of manuals |
Behringer CP35 ATTENUATORS manual content summary:
- Behringer CP35 ATTENUATORS | Quick Start Guide - Page 1
Quick Start Guide CP35 ATTENUATORS Legendary Analog Attenuator and Multiples Module for Eurorack Controls Power Connection (1) (2) (3) (4) (1) IN and OUT JACKS - A single input connected to the first attenuator will pass to all 4 outputs. Additional inputs will break the chain from the previous - Behringer CP35 ATTENUATORS | Quick Start Guide - Page 2
V Voltage References Negative 6 V output Positive 6 V output Impedance Power Power supply Current draw Physical Dimensions Rack units Weight 4 x passive rotary attenuators 4 x 3.5 mm jack, half normalled, DC coupled < 25 kΩ, unbalanced +20 dBu 4 x 3.5 mm jack, DC coupled < 25 kΩ, unbalanced +20 dBu
-
1 -
2
 |
 |
Quick Start Guide
CP35 ATTENUATORS
Legendary Analog Attenuator and
Multiples Module for Eurorack
Controls
(2)
(3)
(4)
(1)
(1)
IN and OUT JACKS
– A single input connected to the first
attenuator will pass to all 4 outputs. Additional inputs
will break the chain from the previous input. For example,
input 1 will initially feed all 4 outputs. If you add a signal
to input 2, then input 1 will only feed output 1, and input 2
will feed outputs 2, 3, and 4.
(2)
ATTENUATOR KNOBS
– Adjust the level of the input
signal passively from -∞ to unity (0 dB).
(3)
6 VOLT OUTPUTS
– These outputs give a reference
voltage of -6 Volts on one output pair, and +6 Volts on
the other pair.
(4)
MULTIPLES
– Connect an input signal to one of the 4-jack
sections, then send up to 3 copies of the same signal to
other devices.
Power Connection
The module comes with the required power cable for connecting
to a standard Eurorack power supply system. Follow these
steps to connect power to the module. It is easier to make these
connections before the module has been mounted into a rack
case.
1.
Turn the power supply or rack case power off and
disconnect the power cable.
2.
Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector has
a tab that will align with the gap in the socket, so it cannot
be inserted incorrectly. If the power supply does not have
a keyed socket, be sure to orient pin 1 (-12 V) with the red
stripe on the cable.
3.
Insert the 10-pin connector into the socket on the back of
the module. The connector has a tab that will align with the
socket for correct orientation.
4.
After both ends of the power cable have been securely
attached, you may mount the module in a case and turn on
the power supply.
Installation
The necessary screws are included with the module for mounting
in a Eurorack case. Connect the power cable before mounting.
Depending on the rack case, there may be a series of fixed holes
spaced 2 HP apart along the length of the case, or a track that
allows individual threaded plates to slide along the length of the
case. The free-moving threaded plates allow precise positioning
of the module, but each plate should be positioned in the
approximate relation to the mounting holes in your module
before attaching the screws.
Hold the module against the Eurorack rails so that each of the
mounting holes are aligned with a threaded rail or threaded
plate. Attach the screws part way to start, which will allow small
adjustments to the positioning while you get them all aligned.
After the final position has been established, tighten the
screws down.