Behringer DIGITAL REVERB/DELAY DR400 Manual
Behringer DIGITAL REVERB/DELAY DR400 Manual
 |
View all Behringer DIGITAL REVERB/DELAY DR400 manuals
Add to My Manuals
Save this manual to your list of manuals |
Behringer DIGITAL REVERB/DELAY DR400 manual content summary:
- Behringer DIGITAL REVERB/DELAY DR400 | Manual - Page 1
DIGITAL REVERB/DELAY DR400 Digital Stereo Reverb/Delay Effects Pedal Thank you for showing your confidence in us by purchasing the BEHRINGER DIGITAL REVERB/ DELAY DR400. This Reverb/Delay effects pedal delivers 24-bit high-resolution stereo reverb and delay effects. Experience state-of-the-art - Behringer DIGITAL REVERB/DELAY DR400 | Manual - Page 2
DIGITAL REVERB/DELAY DR400 The BATTERY COMPARTMENT is located underneath the pedal cover. To install or replace the 9 V battery (not included), press the hinges with a ballpoint pen and remove the pedal cover. Be careful not to scratch the unit. ◊ The DR400 has no On/Off switch. It is operable as
-
1 -
2
 |
 |
DIGITAL REVERB/DELAY DR400
Digital Stereo Reverb/Delay Effects Pedal
Thank you for showing your confidence in us by purchasing the BEHRINGER DIGITAL REVERB/
DELAY DR400. This Reverb/Delay effects pedal delivers 24-bit high-resolution stereo reverb and
delay effects. Experience state-of-the-art sounds comparable to studio processors in one compact pedal.
1.
Controls
(4)
(1)
(3)
(8)
(6)
(7)
(5)
(2)
(1)
Select the effect mode via the
MODE
switch (see table below).
(2)
Depending on the selected mode,
this knob adjusts the reverb time or
the delay time.
(3)
Use the ¼" TS
IN
connector to plug in
the instrument cable.
(4)
The
BALANCE
control determines
the balance between the direct
(dry instrument) signal and the
effect sound.
(5)
In REVERB mode, this knob adjusts
the reverbs’ tonal character. In delay
and DLY+rev mode, this knob
adjusts the amount of feedback
(number of repetitions).
(6)
The two ¼" TS connectors
OUT A
and
OUT B
send the signal to your amp or other effects devices.
Use both connectors if you want to achieve a full stereo effect. For mono use, just plug in OUT A.
(7)
The
ON/BATT
LED illuminates when the effect is activated. It also serves as a
battery level indicator.
(8)
Use the foot switch to activate/deactivate the effect. When pressing the foot switch
2 seconds or longer, you can tap in the delay time (ON/BATT LED flashes).
(9)
Use the
DC IN
connection at the front of the unit to plug in a 9 V power supply (not included).
1
Effect description
2
3
8
DELAY
1
Short delay (32 - 128 ms)
Delay time
Feedback
Tap delay time
2
Medium delay (128 - 500 ms)
Delay time
Feedback
3
Long delay (500 - 2000 ms)
Delay time
Feedback
DLY + REV
4
Delay+small room (32 - 2000 ms)
Delay time
Feedback
5
Delay+big room (32 - 2000 ms)
Delay time
Feedback
6
Delay+concert hall (32 - 2000 ms)
Delay time
Feedback
7
Delay+reverb plate (32 - 2000 ms)
Delay time
Feedback
REVERB
8
Simulates the reverb of a small room
Reverb time
Tone
—
9
Simulates the reverb of a big room
Reverb time
Tone
10
Simulates the reverb of a concert hall
Reverb time
Tone
11
Simulates the sound of a reverb plate
Reverb time
Tone