Behringer U-CONTROL UMX490 Manual - Page 12
°CH°1°, °CH°16°, °°8°°, °°9°°, °°0°°
View all Behringer U-CONTROL UMX490 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 12 highlights
12 U-CONTROL UMX610/UMX490 User Manual b) Sequential scrolling in program libraries. 4.2.10 Velocity sensitivity Most sound producers have the option to store presets in a separate bank (frequently called a User Bank). If the sequence of songs to be played at a concert is defined by your band, you can store all of the sounds used for the gig in the User Bank in the sequence they occur in the concert and completely concentrate on your playing. A cumbersome search for sounds in the sound producers is no longer required thanks to the OCTAVE SHIFT push-buttons. 1) Press the ASSIGN push-button and hold it down. 2) Press the PROG +/- key. 3) Release the ASSIGN push-button. The sensitivity of the UMX can be regulated so that the velocity of the keys has an effect on the volume level. 1) Press the ASSIGN button and keep it pressed. 2) Use the number keys to enter the keyboard velocity (see Table 4.1). 3) Release the ASSIGN button. 4) Confirm your selection with ENTER. To discard your assignments either press the CANCEL key or the ASSIGN button again. In all 3 cases the ASSIGN LED goes out. 4) Finally, press the ENTER key. In order to discard your assignments, please press the CANCEL key or press the ASSIGN push-button again. The ASSIGN LED will go off in all 3 cases. Pressing the right hand one of the two push-buttons now causes your external device to switch one preset number upward to be switched upward in your external device; pressing the left hand causes a step downward in your preset library. By pressing both push-buttons you jump to Preset 0 in the current bank. Please note that you must assign an individual MIDI channel to the OCTAVE SHIFT push-buttons if you do not want to work in the GLOBAL CHANNEL (refer to Chapter 4.2.2). KEY EFFECT ON KEY VELOCITY 0 OFF: velocity value is fixed to 110. Change of key pressure has no effect on volume level. 1 SOFT: key pressure is very sensitive; low velocity changes create high changes in volume level 2 MEDIUM: key pressure is "normal"; (very) hard hit notes are (very) loud, (very) soft hit notes produce (very) low volume 3 HARD: key pressure is more unsusceptible compared to all other settings 4-9 invalid input Tab. 4.1: Effect of RANGE definition on keyboard velocity ◊ In case of the stepwise search function, the channel assignment always affects both the push-buttons. The assignment of a separate channel to one of the 2 push-buttons is not supported. c) Optional controller functions Please note that the OCTAVE SHIFT push-buttons generate switch controllers in the event of a controller assignment. One of the two values 0 or 127 will always be produced. ◊ There are two exceptions: if you assign controller CC 07 (Channel Volume) to the OCTAVE SHIFT push-buttons, pressing one of the push-buttons will always generate the value 0. In case of controller CC 10 (panning), pressing a push-button will always produce the value 64. ◊ Please note that pressing both push-buttons simultaneously does not generate anything when assigning a controller. 1) Press the ASSIGN button and keep it pressed. 2) Press the one of the two OCTAVE SHIFT buttons to which you want to assign a controller. 4.2.11 The factory reset command To reset all settings on your UMX, proceed as follows: 1) Press the ASSIGN push-button and hold it down. 2a) To cause a temporary FACTORY RESET, simultaneously press both OCTAVE SHIFT push-buttons. All temporarily changed control elements are returned to their factory settings. The USER MEMORY, however, is retained and will not be reset. 2b) Simultaneously press the ( 8 ), ( 9 ) and ( 0 ) keys to perform a complete FACTORY RESET. In this case, the USER memory is also overwritten, in addition to resetting all control elements of the FACTORY MEMORY. 3) Release the ASSIGN push-button again. The LED of the ASSIGN push-button stays on. 4) Finally, press the ENTER key. If you do not wish to perform the RESET command, please press either the CANCEL key or press the ASSIGN push-button again. 3) Release the ASSIGN button. 4) Assign the channel. Press one of the 16 channel keys ( CH 1 ) to ( CH 16 ). You can assign each of both the OCTAVE SHIFT buttons to an individual MIDI channel. 5) Press the CC key to be found under BUTTON ASSIGN . 6) Press the number keys on the keyboard to enter the controller number of your choice (as described in Chapter 4.2.7). 7) Confirm your selection with ENTER. To discard your assignments either press the CANCEL key or the ASSIGN button again. In all 3 cases the ASSIGN LED goes out.