BenQ MP610 User Manual
BenQ MP610 - SVGA DLP Projector Manual
 |
UPC - 840046012731
View all BenQ MP610 manuals
Add to My Manuals
Save this manual to your list of manuals |
BenQ MP610 manual content summary:
- BenQ MP610 | User Manual - Page 1
MP610 Digital Projector Portable Series User's Manual Welcome - BenQ MP610 | User Manual - Page 2
or fitness for any particular purpose. Further, BenQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes. *DLP, Digital Micromirror Device and DMD are trademarks of - BenQ MP610 | User Manual - Page 3
safety instructions 1 Introduction 5 Projector features 5 Shipping contents 6 Optional accessories 6 Projector exterior view 7 Front / upper side 7 Rear side ...7 Lower side ...7 Controls and functions 8 External control panel 8 Remote control 9 Remote control effective range 10 Replacing - BenQ MP610 | User Manual - Page 4
image 25 Remote paging operations lamp hour 37 Warning message 37 Replacing the lamp 38 Temperature information 40 Indicators...41 Safety instructions for ceiling mounting of your BenQ projector 43 Troubleshooting 44 Specifications 45 Projector specifications 45 Timing chart 46 Supported - BenQ MP610 | User Manual - Page 5
Limited Warranty 48 Regulation Statements 49 FCC statement 49 EEC statement 49 MIC statement 49 Table of contents v - BenQ MP610 | User Manual - Page 6
vi Table of contents - BenQ MP610 | User Manual - Page 7
on the product. Caution • To prevent shock, do not open the • Refer servicing to qualified service cabinet. There are no user serviceable personnel. parts inside. • Always open the lens shutter or remove the lens cap when the projector lamp is on. • Please read this user's manual before you - BenQ MP610 | User Manual - Page 8
technician when service or repair is required. Incorrect reassembly can cause malfunction of the projector or electric shock when the appliance is subsequently used. 3. Never replace the lamp assembly or any electronic components unless the projector is unplugged. 2 Important safety instructions - BenQ MP610 | User Manual - Page 9
the inside of a car with all windows rolled up. - Do not place inflammables near the projector. - Locations where excessive humidity, it is not fully horizontal may cause a malfunction of, or damage to, the lamp. - Locations near fire alarms - Locations with an ambient temperature above 40°C / - BenQ MP610 | User Manual - Page 10
projector or remote control. 12. Do not place liquids near or on the projector. Liquids spilled into the projector may cause it to fail. If the projector does become wet, disconnect it from the power supply's wall socket and call BenQ to have the projector serviced. 4 Important safety instructions - BenQ MP610 | User Manual - Page 11
and a user-friendly design to deliver high reliability and ease of use. The projector offers the following features: • Selectable password protected function • Compact and portable unit • High quality manual zoom lens • One-key auto-adjustment to display the best picture quality • Digital keystone - BenQ MP610 | User Manual - Page 12
from those illustrated. Projector Soft carry case User's manual User's manual CD Pull the tab before using the remote control. Quick start Remote control guide with battery VGA cable USB cable Optional accessories 1. Macintosh adapter 2. 200W lamp module 3. Ceiling mount kit Power cord - BenQ MP610 | User Manual - Page 13
Projector exterior view Front / upper side 1 2 3 4 5 1. 6 2. 7 3. 4. 5. 6. 7. External control panel (See "External control panel" on page 8 for detailed information.) Ventilation grill Projection lens Front adjuster button Lens cap Focus ring and Zoom ring Front IR remote sensor Rear side Refer - BenQ MP610 | User Manual - Page 14
41 for more information.) Indicates the status of the lamp. Lights up or flashes when the lamp has developed a problem. 7. Temperature warning light (Refer to "Indicators" on page 41 for more information.) Flashes red if the projector's temperature becomes too high. 8. Power indicator light (Refer - BenQ MP610 | User Manual - Page 15
to enlarge the image or rotate counterclockwise to reduce the image size. Remote control 1 7 2 3 8 4 9 5 3 10 11 6 1. II Power (Refer to "Start up" on page 21 and "Shutdown" on page 26 for more information.) Turns the projector on or off. 2. II/ Freeze The image is frozen when Freeze is - BenQ MP610 | User Manual - Page 16
remote control. • Avoid excessive heat and humidity. There may be battery damage if the battery is incorrectly replaced. • Replace only with the same or equivalent type recommended by the battery manufacturer. • Dispose of the used battery according to the manufacturer's instructions. • Never throw - BenQ MP610 | User Manual - Page 17
for quick setup and portability. II. Ceiling front Select this location with the projector suspended upside-down from the ceiling in front of the screen. Purchase the BenQ Projector Ceiling Mounting Kit from your dealer to mount your projector on the ceiling. Set in the Advance > Mirror menu - BenQ MP610 | User Manual - Page 18
the horizontal plane of the projector. When ceiling mounted, this refers to the top edge of the projected image. If the projector is positioned further away from distance. BenQ has provided a table of 4:3-aspect-ratio screen sizes to assist you in determining the ideal location for your projector. - BenQ MP610 | User Manual - Page 19
for these screen sizes, indicates that the 4.5m measured projection distance will fit these screens too. The projector can be adjusted (using the zoom control) to display on these different screen sizes at that projection distance. Be aware that these different screens have different vertical offset - BenQ MP610 | User Manual - Page 20
3048 3500 12 144 3658 4000 15 180 4572 5000 18 216 5436 6000 25 300 7620 Projection distance Distance from Screen in mm Min length Average Max length (with max. (with min. zoom) zoom) tolerance among these numbers due to optical component variations. 14 Positioning your projector - BenQ MP610 | User Manual - Page 21
the computer. 2. Connect the other end of the VGA cable to the D-SUB/COMP IN signal input socket on the projector. 3. If you wish to use the remote paging function (see "Remote paging operations" on page 26), take the supplied USB cable and connect the larger end to the USB port of the - BenQ MP610 | User Manual - Page 22
monitor as well as on the screen, you can connect the RGB signal output socket on the projector to an external monitor with a VGA cable following the instructions below: 1. Connect the projector to a computer as described in "Connecting a computer" on page 15. 2. Take a suitable VGA cable (only one - BenQ MP610 | User Manual - Page 23
Video). Digital TV tuner projector has a built-in mono speaker which is designed to provide basic audio functionality accompanying data presentations for business purposes only. It is not designed for, nor intended for stereo audio reproduction use as might be expected in home theatre or home - BenQ MP610 | User Manual - Page 24
Video output sockets of the Video source device. Match the color of the plugs to the color of the sockets; green to green, blue to blue; 16:9 aspect ratio picture. If you connect the projector to a High Definition TV (HDTV) tuner, the following standards are supported: • 480i • 576i • 720p (50/ 60 - BenQ MP610 | User Manual - Page 25
can continue with this procedure. • If not, you will need to reassess which method you can use to connect to the device. To connect the projector to an S-Video source device: 1. Take the (optional accessory) S-Video cable and connect one end to the S-Video output socket of the Video source device - BenQ MP610 | User Manual - Page 26
can continue with this procedure. • If not, you will need to reassess which method you can use to connect to the device. To connect the projector to an composite Video source device: 1. Take the (optional accessory) Video cable and connect one end to the composite Video output socket of the Video - BenQ MP610 | User Manual - Page 27
control or projector to start the unit. The Power indicator light flashes green and stays green when the unit is on. The start up procedure takes about 30 seconds after pressing Power. In the later stage of start up, a default BenQ logo is projected. 4. If you are prompted for a password, press - BenQ MP610 | User Manual - Page 28
a coded number on the screen. Seek help from the local BenQ service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector. To change the password: 1. Open the on-screen menu and go to Setting > Change - BenQ MP610 | User Manual - Page 29
lamp is on. The strong light from the lamp may cause damage to your eyes. 2. Screw the rear adjuster foot to fine tune the horizontal angle. To retract the foot, hold up the projector in the Picture menu, on the projector control panel, or on the remote control. Auto-adjusting the image In some - BenQ MP610 | User Manual - Page 30
adjust the values by pressing Left 3/ Right 4 on the projector or Left 3/ Right 4on the remote control. For example, 1. Press Left 3 on the projector or 2. Press on the remote control or 3. Press Left 3on the projector or 3 on the remote control when you are in Picture --> Keystone menu. Keystone - BenQ MP610 | User Manual - Page 31
on the projector control panel or the remote control. The selected source name will display at the center of the screen for 3 seconds after each button press. The brightness level of the projected image will change accordingly when you switch between different input signals. Data - BenQ MP610 | User Manual - Page 32
button on the remote control, or the Source button on the projector control panel. Note that projector off. 2. The Power indicator light flashes orange and the lamp shuts down, the fans continue to run for approximately 90 seconds to cool down the projector. • To protect the lamp, the projector - BenQ MP610 | User Manual - Page 33
Time Quick Cooling Password Change Password Reset Mirror Blank Time Source Scan Language Splash Screen High Altitude Mode Auto Off Economic Mode Source Resolution Application Mode Equivalent Lamp Hour Video / S-Video Application Mode Keystone Color Temp Brightness Contrast Color Tint* Auto Resize - BenQ MP610 | User Manual - Page 34
4on the screen menu on. projector or Left 3/ Right 4 on the remote control. 2. Use 3 Left/ Right 4 on the projector or 5. Press5Exit on the projector or Left 3/ Right 4on the remote control press Menu twice* on the to select the Picture menu. remote control to leave and save the setting - BenQ MP610 | User Manual - Page 35
your projector image set-up to suit your program type. You can use the remote control Mode: Is appropriate for playing movies, video clips from digital cameras or DVs through the PC input for best Default): Is suitable for enjoying colorful movies and TV in a home darkened (not bright) lounge - BenQ MP610 | User Manual - Page 36
temperature appears to be reddish white. A white color with a high color temperature appears to have more blue in it. Adjusts the brightness of the image. The higher the value, the brighter the image. And lower the setting, darker the image. Adjust this control so the black areas of the image appear - BenQ MP610 | User Manual - Page 37
towards the screen to increase the image size if necessary. You may also need to refocus the projector after making these adjustments. There are two aspect ratio settings. Aspect Ratio (4:3) H Position (0) 1. 4:3 (for a standard screen) 2. 16:9 (for a wide screen) 16:9 aspect ratio is only - BenQ MP610 | User Manual - Page 38
. Print out this manual (if necessary) and write the password you used in this manual, and keep the manual in a safe place for later recall. The password can be entered by using either the buttons on the projector or the remote control. Change Password Reset The password will display on-screen - BenQ MP610 | User Manual - Page 39
sets the language for the OSD control menus. Use Left 3/ Right 4on the projector or Left 3/ Right 4on the remote control to select your desired language. Allows you to select which logo screen will display during projector startup. Three modes are available: Default (BenQ logo), black screen or blue - BenQ MP610 | User Manual - Page 40
projector will be used for extended periods of time (>10 hours) without shutdown. To activate the High Altitude Mode, select On by pressing Left 3/ Right 4on the projector or remote control mode is used for protecting projector from extreme environment and may cause high fan speed. Operation under " - BenQ MP610 | User Manual - Page 41
you the current operating status of the projector. Some picture adjustments are available only when certain input sources are in use. Unavailable adjustments are not shown on the screen. FUNCTION Source Resolution Application Mode Equivalent Lamp Hour System DESCRIPTION Shows the current signal - BenQ MP610 | User Manual - Page 42
the instructions below: • Make sure the temperature and humidity of the storage area are within the recommended range for the projector. Please refer to "Specifications" on page 45 or consult your dealer about the range. • Retract the adjuster feet. • Remove the batteries from the remote control - BenQ MP610 | User Manual - Page 43
mode. That is, using the projector in Economic mode helps to extend the lamp hour by 1/4. Warning message When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the - BenQ MP610 | User Manual - Page 44
• To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing the lamp. • To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp. • To reduce the risk of injuries to fingers and damage - BenQ MP610 | User Manual - Page 45
might splash on it, children can reach it, or near flammable materials. • Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images. 7. As shown in the figure, hold the new - BenQ MP610 | User Manual - Page 46
the projector or on the remote control to reset the lamp hour to "0". iii. Wait about 5 seconds to let the OSD disappear. Temperature information When the Temperature warning light is on, it is warning you of the following possible problems: 1. The internal temperature is too high. 2. The fans are - BenQ MP610 | User Manual - Page 47
, it will shutdown again. Please contact your dealer for assistance. Light Status & Description Power Temp Lamp Lamp events O - - - The projector has shutdown automatically. If you try to re-start R the projector, it will shutdown again. Please contact your dealer for assistance. 1. The - BenQ MP610 | User Manual - Page 48
Thermal events - R - - R R - R G The projector has shutdown automatically. If you try to re-start R R R the projector, it will shutdown again. Please contact your dealer for assistance. G R R O R R - G R 42 Maintenance - BenQ MP610 | User Manual - Page 49
Safety instructions for ceiling mounting of your BenQ projector We want you to have a pleasant experience using your BenQ projector, so we need to bring this safety matter to your attention to prevent damage to person and property. If you intend to mount your projector on the ceiling, we strongly - BenQ MP610 | User Manual - Page 50
DOES NOT WORK Cause The battery is out of power. There is an obstacle between the remote control and the projector. You are too far away from the projector. Remedy Replace the battery with a new one. Remove the obstacle. Stand within 6 meters (19.5 feet) of the projector. 44 Troubleshooting - BenQ MP610 | User Manual - Page 51
Specifications Projector specifications All specifications are subject to change without notice. General Product name Model name Digital Projector MP610 Optical Resolution Display system Lens F/Number Lamp 800 x 600 SVGA 1-CHIP DMD F=2.6 to 2.77, f= 20.4 to 23.5 mm 200W lamp Electrical - BenQ MP610 | User Manual - Page 52
Supported SVGA_60 SVGA_72 SVGA_75 SVGA_85 XGA_60 XGA_70 XGA_75 XGA_85 SXGA_60 Supported timing for Component-YPbPr input Signal Format 480i(525i 00 50.00 60.00 50.00 60.00 50.00 Supported timing for Video and S-Video inputs Video mode NTSC PAL Color subcarrier Frequency (MHz) 3.58 4.43 4.25 or 4.41 3.58 - BenQ MP610 | User Manual - Page 53
Dimensions Unit: mm Specifications 47 - BenQ MP610 | User Manual - Page 54
replacement of any defective parts (labor included). To obtain warranty service, immediately notify the dealer from which you purchased the product of any defects. Important: The above warranty shall be void if the customer fails to operate the product in accordance with BenQ's written instructions - BenQ MP610 | User Manual - Page 55
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one Reorient or relocate the receiving antenna. - Increase the distance between the equipment and receiver. - Connect the equipment for household purpose, this product can be used in any
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
 |
 |
Welcome
MP610 Digital Projector
Portable Series
User’s Manual