BenQ MX818ST User manual for MX818ST, MX819
BenQ MX818ST Manual
 |
View all BenQ MX818ST manuals
Add to My Manuals
Save this manual to your list of manuals |
BenQ MX818ST manual content summary:
- BenQ MX818ST | User manual for MX818ST, MX819 - Page 1
MX818ST/MX819ST/MW820ST Digital Projector User Manual - BenQ MX818ST | User manual for MX818ST, MX819 - Page 2
instructions 3 Introduction 7 Projector features 7 Shipping contents 8 Projector exterior view 9 Controls and functions 10 Positioning your projector 47 Care of the projector 47 Lamp information 48 Troubleshooting......... 54 Specifications 55 Projector specifications 55 Dimensions 56 - BenQ MX818ST | User manual for MX818ST, MX819 - Page 3
the instructions mentioned in this manual and marked on the product. Safety Instructions 1. Please read this manual before 5. you operate your projector. your projector through a power stabilizer, surge protector or uninterruptible power supply (UPS). 3. Refer servicing to qualified service - BenQ MX818ST | User manual for MX818ST, MX819 - Page 4
should you ever undo or remove any other covers. Refer servicing only to suitably qualified professional service personnel. 9. Never replace the lamp assembly or any electronic components unless the projector is unplugged. 12. When the projector is under operation, you may sense some heated air - BenQ MX818ST | User manual for MX818ST, MX819 - Page 5
it is not fully horizontal may cause a malfunction of, or damage to, the lamp. 3000 m (10000 feet) 0 m (0 feet) 16. Do not stand the projector on end vertically. Doing so may cause the projector to fall over, causing injury or resulting in damage to the projector. Important safety instructions 5 - BenQ MX818ST | User manual for MX818ST, MX819 - Page 6
. 18. Do not place liquids near or on the projector. Liquids spilled into the projector may cause it to fail. If the projector does become wet, disconnect it from the power supply's power outlet and call BenQ to have the projector serviced. 19. This product is capable of displaying inverted images - BenQ MX818ST | User manual for MX818ST, MX819 - Page 7
AMX supported The projector supports Crestron eControl and RoomView, PJ Link and AMX allowing you to control and manage equipment from a remote computer 3D Function supported Various 3D formats make the 3D function more flexible. By presenting the depth of the images, you can wear BenQ 3D glassed - BenQ MX818ST | User manual for MX818ST, MX819 - Page 8
only supplied in some specific regions. Please consult your dealer for detailed information. Projector QDuigiictkalSPtraortjeGctuoidr e Quick start guide Power cord VGA cable User manual CD Warranty card* Remote control with batteries Optional accessories 1. Spare lamp kit 2. Ceiling mount kit - BenQ MX818ST | User manual for MX818ST, MX819 - Page 9
Projector exterior view Front/upper side 1 2 3 5 6 4 7 8 9 10 Rear/lower side 12 power jack 12. RS232 control port 13. RJ45 LAN input jack 14. USB mini B type port 15. Rear IR remote sensor 16. HDMI-input port 17. RGB signal output jack 18. RGB (PC)/Component Video (YPbPr/ YCbCr) signal - BenQ MX818ST | User manual for MX818ST, MX819 - Page 10
the of the lamp. Lights up lamp has developed a 11. problem. POWER Toggles the projector between standby mode and on. 3. MENU/EXIT Turns on the Down) Manually corrects distorted images resulting from an angled projection. 8. TEMP (Temperature) warning light Lights up red if the projector's - BenQ MX818ST | User manual for MX818ST, MX819 - Page 11
Remote control 1 2 12 6 3 13 4 14 5 6 15 16 7 8 17 9 18 10 19 11 20 21 22 1. ON/ OFF Toggles the projector between standby mode and on. the best picture Down) timings for the displayed image. Manually corrects distorted images resulting from an angled projection. 7. LASER - BenQ MX818ST | User manual for MX818ST, MX819 - Page 12
mode. 21. TEST Displays the test pattern. Remote control effective range The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensor(s) to function correctly. The distance between the remote control and the sensor(s) should not exceed - BenQ MX818ST | User manual for MX818ST, MX819 - Page 13
into position. Stop when it clicks into place. • Avoid leaving the remote control and batteries in an excessive heat or humid environment like the kitchen, • Dispose of the used batteries according to the manufacturer's instructions and local environment regulations for your region. • Never throw - BenQ MX818ST | User manual for MX818ST, MX819 - Page 14
Set Rear Ceiling in the SYSTEM SETUP: Basic > Projector Installation menu after you turn the projector on. 2. Front Ceiling Select this location with the projector suspended upside-down from the ceiling in front of the screen. Purchase the BenQ Projector Ceiling Mount Kit from your dealer to mount - BenQ MX818ST | User manual for MX818ST, MX819 - Page 15
size. Projection dimensions Refer to "Dimensions" on page 56 for the center of lens dimensions of this projector before calculating the appropriate position. MX818ST/MX819ST (a) Screen Center of lens (c) (b) The screen aspect ratio is 4:3 and the projected picture is 4:3 (a) Screen size Diagonal - BenQ MX818ST | User manual for MX818ST, MX819 - Page 16
. All measurements are approximate and may vary from the actual sizes. BenQ recommends that if you intend to permanently install the projector, you should physically test the projection size and distance using the actual projector in situ before you permanently install it, so as to make allowance - BenQ MX818ST | User manual for MX818ST, MX819 - Page 17
electronics stores. • The connection illustrations below are for reference only. The rear connecting jacks available on the projector vary with each projector model. Monitor Notebook or desktop computer A/V device (VGA) (DVI) 12 3 19 45 9 6 7 8 Speakers 9 or or 1. VGA cable 6. Audio - BenQ MX818ST | User manual for MX818ST, MX819 - Page 18
use this connection method when the projector is in standby mode, make sure the Monitor Out function is turned on in the SYSTEM SETUP: Advanced menu. See "Standby Settings" on page 45 for details. Connecting video source devices You need only connect the projector to a video source device using just - BenQ MX818ST | User manual for MX818ST, MX819 - Page 19
projector is activated for the first time, select your OSD language following the onscreen instructions. 4. If you are prompted for a password, press the arrow keys to enter a six-digit is found. You can also press SOURCE on the projector or remote control to select your desired input signal. See " - BenQ MX818ST | User manual for MX818ST, MX819 - Page 20
from. Auto-adjusting the image In some cases, you may need to optimize the picture quality. To do this, press AUTO on the projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture - BenQ MX818ST | User manual for MX818ST, MX819 - Page 21
is not perpendicular to the screen. To correct this, follow ONE of these steps: • Press / on the projector or remote control to display the Keystone correction page. Press to correct keystoning at the top of the image. Press to correct keystoning at Press / . the bottom - BenQ MX818ST | User manual for MX818ST, MX819 - Page 22
Sub-menu DISPLAY Wall Color Aspect Ratio Keystone Position Phase H. Size Digital Zoom 3D Teaching Template Off Auto ENTER 0 0 Highlight Current input BenQ BenQ Analog RGB MENU Exit 4. Press / / / to select a preferred language and press MODE/ENTER. 5. Press MENU/EXIT on the projector or remote - BenQ MX818ST | User manual for MX818ST, MX819 - Page 23
Lock function is activated, you have to enter the correct password to turn on the projector. IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you - BenQ MX818ST | User manual for MX818ST, MX819 - Page 24
projector or remote control for 3 seconds. The RECALL PASSWORD projector will display a coded number on the screen. 2. Write down the number and turn off your Please write down the recall code, and contact BenQ Customer Center. projector. Recall Code: 3. Seek help from the local BenQ service - BenQ MX818ST | User manual for MX818ST, MX819 - Page 25
you want the projector to automatically search for the signals. To select the source: 1. Press SOURCE on the projector or remote control. A source Video Network Display • The native display resolution of this projector is in a 4:3 (MX818ST/MX819ST)/16:10 (MW820ST) aspect ratio. For best display - BenQ MX818ST | User manual for MX818ST, MX819 - Page 26
the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal. To change the projected picture ratio (no matter what aspect the source is): • Using the remote control - BenQ MX818ST | User manual for MX818ST, MX819 - Page 27
be displayed on those unused black areas. 1. Auto: Scales an image proportionally to fit the projector's native resolution in its horizontal or vertical width. This is suitable for the incoming image MX818ST/ MW820ST MX819ST which is neither in 4:3 nor 16:9 and you want to make most use of the - BenQ MX818ST | User manual for MX818ST, MX819 - Page 28
can follow one of the following steps. • Press MODE/ENTER on the projector or remote control repeatedly until your desired mode is selected. • Go to the PICTURE Cinema mode: Is appropriate for playing colorful movies, video clips from digital cameras or DVs through the PC input for best viewing in a - BenQ MX818ST | User manual for MX818ST, MX819 - Page 29
functions may not be available. Based on your needs, you can make adjustments to these functions by highlighting them and pressing / on the projector or remote control. Adjusting Brightness The higher the value, the brighter the image. And the lower the setting, the darker the image. Adjust this - BenQ MX818ST | User manual for MX818ST, MX819 - Page 30
test patterns and can be used to test the color presentation on monitors, TVs, projectors, etc, you can project any image from the disc on and highlight 3D Color Management. 2. Press MODE/ENTER on the projector or remote control and the 3D Color Management page displays. 3. Highlight Primary Color - BenQ MX818ST | User manual for MX818ST, MX819 - Page 31
Please refer to the illustration to the right for how the colors relate to each other. For example, if you select Red and set its range at 0, only pure red in the projected picture will be selected. Increasing its range will include red close to yellow and red close to magenta. 5. Press to - BenQ MX818ST | User manual for MX818ST, MX819 - Page 32
correctly made and the mouse driver on your computer is updated to the latest version. The remote paging function cannot work with the screen. To release the function, press any key on the projector or remote control. If your remote control has the following keys, please note that they cannot be - BenQ MX818ST | User manual for MX818ST, MX819 - Page 33
Hiding the image In order to draw the audience's full attention to the presenter, you can use ECO BLANK on the projector or remote control to hide the screen image. When this function is activated with an audio input connected, the audio can still be sheard. You can set - BenQ MX818ST | User manual for MX818ST, MX819 - Page 34
/ENTER. The Audio Settings page displays. 3. Highlight Mute and press / to select On. If available, you can also press MUTE on the remote control to toggle projector audio between on and off. Adjusting the sound level To adjust the sound level, press / , or: 1. Repeat steps 1-2 above. 2. Press to - BenQ MX818ST | User manual for MX818ST, MX819 - Page 35
Using the teaching templates The projector provides several preset patterns for various teaching purposes. To activate the pattern: 1. Open the OSD menu and go to the DISPLAY > Teaching Template menu and - BenQ MX818ST | User manual for MX818ST, MX819 - Page 36
flashes orange, the projection lamp shuts down, and the fans will continue to run for approximately 90 seconds to cool down the projector. To protect the lamp, the projector will not respond to any commands during the cooling process. To shorten the cooling time, you can also activate the Quick - BenQ MX818ST | User manual for MX818ST, MX819 - Page 37
display (OSD) menus vary according to the signal type selected and the projector model you are using. Main menu Sub-menu Options 1. DISPLAY 2. PICTURE Ratio Auto/Real/4:3/16:9/16:10 Keystone Position Phase H. Size Digital Zoom 3D 3D Mode Auto/Top Bottom/Frame Sequential/ Frame Packing - BenQ MX818ST | User manual for MX818ST, MX819 - Page 38
Count Down/Count Up Sound Reminder On/Off On/Off Language 4. SYSTEM SETUP: Basic Projector Installation Front Table/Rear Table/Rear Ceiling/ Front Ceiling Menu Display Time 5 sec/10 hr/2 hr/3 hr/4 hr/8 hr/ 12 hr Remote Receiver Front+Rear/Front/Rear Panel Key Lock On/Off Background Color - BenQ MX818ST | User manual for MX818ST, MX819 - Page 39
Enable On/Off Caption Version CC1/CC2/CC3/CC4 Network On/Off Standby Monitor Out On/Off Settings Audio Pass Off/Audio in 1/Audio in 2/Audio Version Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the - BenQ MX818ST | User manual for MX818ST, MX819 - Page 40
selected. Adjusts the clock phase to reduce image distortion. H. Size Digital Zoom 3D This function is only available when a PC signal (analog Magnifying and searching for details" on page 26 for details. This projector features a 3D function which enables you to enjoy the 3D problem. 40 Operation - BenQ MX818ST | User manual for MX818ST, MX819 - Page 41
details. Picture Mode Reference Mode Brightness Contrast Color Tint Sharpness Brilliant Color Pre-defined picture modes are provided so you can optimize your projector image set-up to suit your program type. See "Selecting a picture mode" on page 28 for details. Selects a picture mode that best - BenQ MX818ST | User manual for MX818ST, MX819 - Page 42
Space" on page 25 for details. Presentation Timer Language Projector Installation Menu Settings Reminds the presenter to finish the Display (OSD) menus. See "Using the menus" on page 22 for details. The projector can be installed on a ceiling or behind a screen, or with one or more mirrors - BenQ MX818ST | User manual for MX818ST, MX819 - Page 43
. See "Hiding the image" on page 33 for details. Sleep Timer Sets the auto-shutdown timer. Allows you to enable all the remote receivers or one specific remote receiver on the projector. Panel Key Lock Background Color Splash Screen Disables or enables all panel key functions except POWER on the - BenQ MX818ST | User manual for MX818ST, MX819 - Page 44
baud rate that is identical with your computer's so that you can connect the projector using a suitable RS-232 cable and update or download the projector's firmware. This function is intended for qualified service personnel. See "Using the test pattern" on page 34 for details. Closed Caption Enable - BenQ MX818ST | User manual for MX818ST, MX819 - Page 45
The projector is able to provide the network function when it is in standby mode. Monitor Out Selecting On enables the function. The projector can output LAN See BenQ Network Projector Operation Guide for details. AMX Device Discovery When AMX Device Discovery is On, the projector can be detected - BenQ MX818ST | User manual for MX818ST, MX819 - Page 46
, PAL, SECAM, YUV, or RGB. Equivalent Lamp Displays the number of hours the lamp has been used. Firmware Version Shows the firmware version of your projector. 46 Operation - BenQ MX818ST | User manual for MX818ST, MX819 - Page 47
the instructions below: • Make sure the temperature and humidity of the storage area are within the recommended range for the projector. Please refer to "Specifications" on page 55 or consult your dealer about the range. • Retract the adjuster feet. • Remove the battery from the remote control - BenQ MX818ST | User manual for MX818ST, MX819 - Page 48
in normal mode SmartEco LampCare Saves up to 70% lamp power consumption to offer a longer lamp life • Setting Auto Power Off This function allows the projector to turn off automatically if no input signal is detected after a set period of time to prevent unnecessary waste of lamp life. To set Auto - BenQ MX818ST | User manual for MX818ST, MX819 - Page 49
>XXXX Hours Lamp usage time exceeded Order a new lamp at lamp.benq.com OK The lamp MUST be replaced before the projector will operate normally. Press MODE/ENTER to dismiss the message. WARNING Out of Lamp Usage Time Replace lamp (refer to User Manual) Then reset lamp timer Order a new lamp at lamp - BenQ MX818ST | User manual for MX818ST, MX819 - Page 50
that you use respirators, safety glasses, goggles or face shield and wear protective clothing such as gloves. 1. Turn the power off and disconnect the projector from the power outlet. If the lamp is hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled. 2. Loosen the - BenQ MX818ST | User manual for MX818ST, MX819 - Page 51
the lamp in locations where water might splash on it, children can reach it, or near flammable materials. • Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images. 8. As - BenQ MX818ST | User manual for MX818ST, MX819 - Page 52
cover. • Loose screw may cause a bad connection, which could result in malfunction. • Do not over tighten the screw. 14. Connect the power and restart the projector. Do not turn the power on with the lamp cover removed. Resetting the lamp timer 15. After the startup logo, open the On-Screen Display - BenQ MX818ST | User manual for MX818ST, MX819 - Page 53
Indicators Light Status & Description Orange Green Flashing Green Orange Flashing Red Green Red Flashing Red Red Green Green Off Off Off Off Off Off Off Red Green Off Green Off Off Off Off Red Red Green Red Red Flashing Red Power events Off Stand-by mode. Off Powering up. Off Normal - BenQ MX818ST | User manual for MX818ST, MX819 - Page 54
Troubleshooting The projector does not turn on. Cause Remedy There is no power from the power cord. Attempting to turn the projector on again during the cooling process. Plug the power cord into the AC power jack on the projector projector if necessary. Open the lens cover. Remote control does - BenQ MX818ST | User manual for MX818ST, MX819 - Page 55
Specifications Projector specifications All specifications are subject to change without notice. Optical Control Resolution (MX818ST/MX819ST) 1024 x 768 XGA Speaker (Stereo) 10 watt x 1 Audio signal output PC audio jack x 1 Digital - HDMI V1.4 x 1 Audio signal input Audio in PC audio jack x 2 - BenQ MX818ST | User manual for MX818ST, MX819 - Page 56
Dimensions 232.6 114.4 Ceiling mount installation Ceiling Mount screw: M4 (Max L = 25 mm; Min L = 20 mm) 207.6 287.3 62 62 Unit: mm 77 76.5 34.5 199.6 78 445.95 397.90 364.40 83.38 141.88 287.3 56 Specifications 123.0 232.6 Unit: mm - BenQ MX818ST | User manual for MX818ST, MX819 - Page 57
floor to bottom f 900 900 900 900 900 900 900 of image (mm) Distance from screen surface to a 790 950 790 970 970 780 950 projector rear case (mm) Distance from top case to the top of b image (mm) 94 124 94 126 126 92 124 Distance from top of wall - BenQ MX818ST | User manual for MX818ST, MX819 - Page 58
1171 1181 Image Width (mm) W 1874 1874 1887 Distance from floor to bottom of image (mm) f 900 900 900 Distance from screen surface to projector lens (mm) a 916 916 926 Distance from top case to the top of image (mm) b 6.8 6.8 7.5 Distance from top of wall mount to ceiling (mm - BenQ MX818ST | User manual for MX818ST, MX819 - Page 59
BenQ recommends that if you intend to permanently install the projector, you should physically test the projection size and distance using the actual projector guide only and may differ depending on several factors relating to any specific installation. • The dimensions are based on the projector - BenQ MX818ST | User manual for MX818ST, MX819 - Page 60
108 1024 x 576 1024 x 600 1280 x 720 1280 x 768 BenQ Notebook Timing BenQ Notebook Timing 1280 x 720_60* 1280 x 768_60* 60.0 64.995 Supported timing for 3D signal with Frame Sequential, Top Bottom and Side by Side formats. **Supported timing for 3D signal with Frame Sequential format. ***Supported - BenQ MX818ST | User manual for MX818ST, MX819 - Page 61
. It is possible that some timings cannot be chosen. Supported timing for HDMI (HDCP) input Vertical Horizontal Pixel Resolution 59.87 47.776 79.5 1024 x 576@60Hz BenQ Notebook Timing 60.00 35.820 46.996 1024 x 600@65Hz BenQ Notebook Timing 1280 x 720 1280 x 720_60* 64.995 - BenQ MX818ST | User manual for MX818ST, MX819 - Page 62
DVI HDMI/DVI HDMI/DVI HDMI/DVI HDMI/DVI HDMI/DVI HDMI/DVI Supported timing for Component-YPbPr input Timing 480i* 480p 576i 576p 720/50p 720 25 30 33.75 74.25 50 56.25 148.5 60 67.5 148.5 • *Supported timing for 3D signal with Frame Sequential format. • Displaying a 1080i(1125i)@60Hz or - BenQ MX818ST | User manual for MX818ST, MX819 - Page 63
(kHz) 15.73 15.63 15.63 15.73 15.63 15.73 15.73 Vertical Frequency (Hz) 60 50 50 60 50 60 60 *Supported timing for 3D signal with Frame Sequential format. Color sub-carrier Frequency (MHz) 3.58 4.43 4.25 or 4.41 3.58 3.58 4.43 4.43 Specifications 63 - BenQ MX818ST | User manual for MX818ST, MX819 - Page 64
BenQ's written instructions, especially the ambient humidity must be inbetween 10% and 90%, temperature in-between 0°C and 35°C, altitude lower than 4920 feet, and avoiding to operate the projector manual or otherwise, without the prior written permission of BenQ Corporation. Disclaimer BenQ
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
 |
 |
MX818ST/MX819ST/MW820ST
Digital Projector
User Manual