Bernina 800DL Manual
Bernina 800DL Manual
 |
View all Bernina 800DL manuals
Add to My Manuals
Save this manual to your list of manuals |
Bernina 800DL manual content summary:
- Bernina 800DL | Manual - Page 1
BERNINA . Instruction-manual 800 - Bernina 800DL | Manual - Page 2
- Bernina 800DL | Manual - Page 3
Model 800 I he various parts of the machine 14 15 16 1 Free-arm cover-plate 2 Needle-plate 3 Presser-foot 4 Needle-clamp 5 Thread guide 6 Face-plate 7 Lamp switch 8 8 Take-up lever BERNINA' 01 9 9 Winder pre-tension 10 Thread tension and thread guide 11 Tension indicator window 17 12 - Bernina 800DL | Manual - Page 4
manual. tr 0, 4 Electrical Connectior Connecting to supply Warning! First compare voltage specified • on machine with Bernina sewing machines. If Light switch. By pressing switch the dazzle-free light can be switched on and off. Pull out light cover sideways to change the bulb. Press bulb - Bernina 800DL | Manual - Page 5
30 strong 90 40 large 100 40 Correct choice of needle and thread. Use only needle system 705 B for Bernina . . . sewing machine 800. Please ensure that y y~ -,. the needle and thread used conform to .. ' '' the table above. The usual needles for sewing are numbers 80, 90 and 100 . while - Bernina 800DL | Manual - Page 6
unwinds in the direction of the arrow. Draw thread through slot and then under tension spring. Do not hold the bobbin. The bobbin must turn in the direction of the arrow when unwinding. , 6 Insertion of the bobbin case into the hook. Raise needle to top position by turning the handwheel. As - Bernina 800DL | Manual - Page 7
steady. Now draw thread through the thread guide (5) up to the slot of the take-up lever (8) and again down to the needle eye. Thread the needle from the front to the back leaving a loose end of approximately 10 cm (4 ins.). i o tnreaa the macrune The thread tension discs. Bernina has the unique - Bernina 800DL | Manual - Page 8
back of the machine; this will release the top thread tension and the material can be removed easily by pulling to the rear. Thread cutter. The lever easy and perfect work. The patented Bernina presser foot clamping lever permits quick and easy changes. The Bernina principle: "Just clip it on!" - Bernina 800DL | Manual - Page 9
satin stitch displacement becomes greater. The spacing - depending on material and higher the number, the wider the zig- thread - by turning the knob to the zag stitch. The knob may be moved left. while sewing but when the machine is stationary only if the needle is out of the material. I 9 - Bernina 800DL | Manual - Page 10
guide on the buttonhole foot. Move needle downwards to foot level and check that needle needle in work in the middle of the foot. Lift foot. Turn work completely clock- Needle Position: left wise. Lower foot again. 1. Bar Tack: Lift needle needle out of work. depending on material and thread - Bernina 800DL | Manual - Page 11
work and to right of the cord same as for the satin stitch. and lift foot. How to sew the buttonhole with reinforcing cord Set machine. Lower needle to the raised foot and make sure that it is in the center. If not do one stitch by turning the hand wheel towards you - Bernina 800DL | Manual - Page 12
Darning Small darning foot 285 Needle: 80-70 Thread: 50 e7) Darning material Stitch width: 0 Stitch length: 0 Drop feed control: center Needle position: lowered The quick mastering of this work depends on regular guiding. Therefore: - Hold the hoop correctly. - Always work from left to - Bernina 800DL | Manual - Page 13
Small darning foot 285 Needle: 80-70 Thread: 50 Darning fine socks (also sleeves) Stitch width: 0 Stitch length: 0 Needle position: center Drop feed control: lowered Darning fine socks Pull work over ring (not ring over the work) stretch it to its maximum and insert the spring. Remembering - Bernina 800DL | Manual - Page 14
Cleaning and oiling Cleaning the machine. During sewing pieces of thread and fluff collect under the needle plate and around the hook. A The cover plate of the free arm should be removed from time to time so that the sewing fluff can be cleaned away. - 11- X. •ritiVe L. • art• • •"er- \\ X ' - Bernina 800DL | Manual - Page 15
long storage; f) the needle plate hole is pitted by 6. Seam irregularities. A bad uneven needle and needs repolishing (bring seam results: the free arm cover plate or needle plate a) if thread remnants are between the to authorized Bernina dealer); thread tension discs; Important note (safety - Bernina 800DL | Manual - Page 16
Address of my Bernina agency: Subject to changes in design from those shown in text and illustrations.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
 |
 |
BERNINA
.
Instruction
-manual
800