Bernina 810 Manual - Page 44

Rectangular

Get Bernina 810 PDF manuals and user guides View all Bernina 810 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Applique work Sewing the corners 2. Pointed corner: Stop sewing 'h cm 3. Blunt corner: Sew until the needle (12/ ") in front of the corner. Then turn is in the middle of the angle. Then 1. Rectangular corner: Put the needle back zigzag while sewing on 0. Raise sew out from centre, replacing the on the outer edge, turn the work and presser foot and turn the material. needle in the middle after every continue sewing. The corner will now Set zigzag onto 112/ again and care- stitch, raising the presser foot and be oversewn. fully continue sewing. turning the work slightly. Curves: Using the same method as for blunt corners. Muill-coloured applique work 2. Trim away surplus applique mate- 3. When covering the contours leave The lower part: rial, cutting as closely as possible to the straight stitched edge uncovered. zigzag stitches. Where a straight This will be covered again by the next 1. Only this part of the applique ma- stitch has been used leave V) cm part. terial should be tacked on. Sew ('/o") beyond stitches. around: Where the colours overlap Top part: Complete in the usual man- use straight stitch and zigzag the ner for applique work. other contours. 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
Applique
work
Sewing
the
corners
1.
Rectangular
corner:
Put
the
needle
on
the
outer
edge,
turn
the
work
and
continue
sewing.
The
corner
will
now
be
oversewn.
Muill-coloured
applique
work
The
lower
part:
1.
Only
this
part
of
the
applique
ma-
terial
should
be tacked
on.
Sew
around:
Where
the
colours
overlap
use
straight
stitch
and
zigzag
the
other
contours.
2.
Pointed
corner:
Stop
sewing
'h
cm
(
1
/
2
")
in
front
of
the
corner.
Then
turn
back
zigzag
while
sewing
on
0.
Raise
presser
foot
and
turn
the
material.
Set
zigzag
onto
1
1
/
2
again
and
care-
fully
continue
sewing.
2.
Trim
away
surplus
applique
mate-
rial,
cutting
as
closely
as
possible
to
zigzag
stitches.
Where
a
straight
stitch
has
been
used
leave
V)
cm
('/o")
beyond
stitches.
3.
Blunt
corner:
Sew
until
the
needle
is
in
the
middle
of
the
angle.
Then
sew
out
from
centre,
replacing
the
needle
in
the
middle
after
every
stitch,
raising
the
presser
foot
and
turning
the
work
slightly.
Curves:
Using
the
same
method
as
for
blunt
corners.
3.
When
covering
the
contours
leave
the
straight
stitched
edge
uncovered.
This
will
be
covered
again
by
the
next
part.
Top
part:
Complete
in
the
usual
man-
ner
for
applique
work.
43