Bissell PowerForce Vacuum User Guide - English - Page 5

Warning - parts

Get Bissell PowerForce Vacuum PDF manuals and user guides View all Bissell PowerForce Vacuum manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

How to use this guide This User's Guide has been designed to help you get the utmost satisfaction from your BISSELL PowerForce. You'll find assembly and operating instructions, safety precautions, as well as maintenance and troubleshooting instructions. Please read this Guide thoroughly before assembling your vacuum cleaner. Pay particular attention to the product diagram, assembly instructions, and part names. Locate and organize all parts before assembly. Following this User's Guide will greatly enhance your ability to get the most performance from your BISSELL PowerForce for many years. Warning: Plastic film can be dangerous. To avoid danger of suffocation, keep away from babies and children. 1. 3. Assembly The only tool you'll need to assemble your vacuum cleaner is a Phillips screwdriver. Attach handle to vacuum 1. Stand the vacuum upright and slide the base of the handle firmly into the grooves at the top of the vacuum body. 2. Check to be sure the handle is fitted to the 1. vacuum body. If there is a gap in front, continue to push firmly until the handle is flush. 3. Insert one screw from the assembly packet into the existing hole in the back of the handle. Tighten securely with a screwdriver. Attach vacuum hose and tools 1. Position the hose collar on the back of the vacuum as shown. 2. Attach the hose collar with two screws from the assembly packet. Tighten securely with a screwdriver. 4. 3. Line up the tabs on the base of the Twist 'n Snap Hose with the corresponding tab notches on the hose collar as shown. Turn the Twist 'n Snap Hose to the left to lock the hose into place. 4. Grasping the Quick Reach® Handle, slide the end of the hose wand onto the suction intake opening. Snap the hose into the hose clip. NOTE: The powerfoot will not operate effectively unless the hose wand is firmly attached to the suction intake opening. 5. Place the crevice tool inside the extension wand and slide them into the storage clip as shown. 6. Snap the combination upholstery/dusting brush tool into the storage clip as shown. www.bissell.com Hose Collar 3. 5. 6. 800.237.7691 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
5
www.bissell.com
800.237.7691
H
ow to use this guide
A
ssembly
WARNING:
Plastic film can be
dangerous. To avoid
danger of suffocation,
keep away from babies
and children.
4.
1.
1.
3.
Hose
Collar
3.
This User’s Guide has been designed to help you
get the utmost satisfaction from your BISSELL
PowerForce. You’ll find assembly and operating
instructions, safety precautions, as well as
maintenance and troubleshooting instructions.
Please read this Guide thoroughly before
assembling your vacuum cleaner.
Pay particular attention to the product diagram,
assembly instructions, and part names. Locate
and organize all parts before assembly. Following
this User’s Guide will greatly enhance your ability
to get the most performance from your BISSELL
PowerForce for many years.
The only tool you’ll need to assemble your
vacuum cleaner is a Phillips screwdriver.
Attach handle to vacuum
1.
Stand the vacuum upright and slide the base
of the handle firmly into the grooves at the top
of the vacuum body.
2.
Check to be sure the handle is fitted to the
vacuum body. If there is a gap in front, continue
to push firmly until the handle is flush.
3.
Insert one screw from the assembly packet
into the existing hole in the back of the
handle. Tighten securely with a screwdriver.
Attach vacuum hose and tools
1.
Position the hose collar on the back of the
vacuum as shown.
2.
Attach the hose collar with two screws from
the assembly packet. Tighten securely with
a screwdriver.
3.
Line up the tabs on the base of the Twist ‘n Snap
Hose with the corresponding tab notches on the
hose collar as shown. Turn the Twist ‘n Snap Hose
to the left to lock the hose into place.
4.
Grasping the Quick Reach
®
Handle, slide the
end of the hose wand onto the suction intake
opening. Snap the hose into the hose clip.
NOTE: The powerfoot will not operate
effectively unless the hose wand is firmly
attached to the suction intake opening.
5.
Place the crevice tool inside the extension wand
and slide them into the storage clip as shown.
6.
Snap the combination upholstery/dusting brush
tool into the storage clip as shown.
5.
6.