Bosch DS860 Installation Instructions

Installation Instructions

for the DS860 Series

TriTech Microwave/PIR Intrusion Detectors

1.0

Specifications

•

Dimensions (HxWxD):

5 in. x 2.8 in. x 2.2 in.

(12.7 cm x 7.1 cm x 5.6 cm)

•

Input Power:

9 to 15 VDC, 16 mA DC nominal

(up to 48 mA DC during walk testing or

trouble conditions). Useonly an

Approved Limited Power Source.

•

Standby Power:

No internal standby battery.

Standby power

must

be provided by

an Approved Limited Power Source.

Sixteen mAh required for each hour of

standby time needed.

For UL Listed

Requirements, four hours (64 mAh)

minimum are required.

•

Alarm Relay:

Silent operating Normally Closed

reed relay. Contacts rated 3 watts,

125 mA, 28 VDC maximum for DC

resistive loads; and protected by a

4.7 ohm, 0.5 watt resistor in the

common "C" leg of the relay. To be

connected to a SELV (Safety Extra-Low

Voltage) circuit only. Do

not

use with

capacitive or inductive loads.

•

Temperature Range:

-40°F to +120°F (-40°C to +49°C).

For UL Listed Requirements, the

temperature range is +32°F to +120°F

(0°C to +49°C).

•

Microwave Frequency:

DS860:

10.525 GHz (UL Listed)

DS860A:

10.687 GHz (Export only,

not

UL

Listed)

DS860B:

9.9 GHz (Export only,

not

UL Listed))

•

Coverage:

Broad (standard):

60 ft. by 60 ft. (18 m by 18 m)

Long Range (optional):

100 ft. by 10 ft. (30 m by 3 m)

•

Internal Pointability:

+2° to –10° Vertical, ±10° Horizontal.

•

Tamper:

Normally Closed (with cover on).

Contacts rated at 28 VDC, 125 mA

max. To be connected to a SELV

(Safety Extra-Low Voltage) circuit

only. Connect tamper circuit to 24-hour

protection circuit.

•

Options:

B328 Gimbal Mount Bracket, B335

Low Profile Swivel Mount Bracket,

B338 Ceiling Mount Bracket, OLR92

Long Range Barrier Lens

NOTE:

Use of a bracket may reduce range and increase dead

zone areas.

•

U.S. Patent Numbers:

Protected under one or more of the

following U.S. Patent Numbers:

#4,660,024, #4,764,755,

#5,077,548, #5,208,567,

#5,262,783, and #5,450,062. Other

patents pending.

•

Compliance:

This device complies with Part 15 of the FCC

Rules and with RSS-210 of Industry and Science Canada.

Operation is subject to the following two conditions:

(1)

this device may not cause harmful interference, and

(2)

this device must accept any interference received,

including interference that may cause undesirable

operation.

Changes or modifications not expressly approved by Bosch

Security Systems can void the user’s authority to operate the

equipment.

2.0

Installation Considerations

NOTE:

The DS860 is

not

recommended for installations

containing pets or small animals. Use the DS820 or

DS835 for such installations.

•

Never

install the detector in an environment that causes an

alarm condition in one technology. Good installations start with

the LED

OFF

when there is no target motion. It should never be

left to operate with the tri-color LED in a constant or intermittent

green, yellow, or red condition.

•

Point the unit away from outside traffic (roads/alleys).

NOTE:

Microwave energy will pass through glass and most

common non-metallic construction walls.

•

Avoid installations where rotating machines (e.g. ceiling fans)

are normally in operation within the coverage pattern. Point the

unit away from glass exposed to the outdoors and objects that

may change temperature rapidly.

NOTE:

The PIR detector will react to objects rapidly changing

temperature within its field-of-view.

•

Eliminate interference from nearby outside sources.

3.0

Mounting

•

Select a location likely to intercept an intruder moving

across

the coverage pattern. The surface should be solid and

vibration-free. Mounting height range is 6 to 8 ft. (1.8 to

2.4 m). Recommended mounting height is 7.5 ft. (2.3 m).

•

Remove the cover. Insert a flathead screwdriver into the locking

tab hole at the bottom front of the detector. Pull the cover up

and forward.

Vertical

Adjust

Screw

Tri-color

LED

Terminal

Strip

LED

On/Off

Pins

MW

0°

- 4°

- 8°

On

Off

Microwave

Range Adjust

PIR

Sensitivity

Selection Pins

Vertical Adjust

Scale

Look Down Lens

MIN

MAX

Face of Lens

(masking area)

Corner Mount

Knockout (4)

Surface Mount

Knockout (2)

Wire

Entrances

Bracket Mount

Knockout

Vertical Adjust

Screw Mount

Cover Tab and

Locking Screw Hole

Wire

Entrances

•

Remove the circuit board from the base. Loosen the Vertical

Adjust Screw and slide the circuit board down, then out.

•

Break away the appropriate thin-wall wire entrance and

mounting hole coverings in the base.

•

Using the base as a template and aligning it so that the

detector will be mounted with the terminal block at the top and

the PIR lens at the bottom, mark the location of the mounting

holes on the mounting surface. Pre-start the mounting screws.

Bosch DS860 Installation Instructions

Bosch DS860 Manual

Bosch DS860 manual content summary: