Bosch SHX7ER55UC Instructions for Use - Page 8

Dishwasher Setup - dishwasher model

Page 8 highlights

Dishwasher Setup Water Softening System Your dishwasher requires soft water to ensure proper washing results and is equipped with an internal water softening system. However, if you have a household water softening system, the internal system provided is not needed. For the water softening system to function properly, it will need to use the dishwasher water softening salt. The amount of salt dispensed can be set from "H:00" to "H:07". Salt is not required at H:00 (this is the default factory setting). The amount of salt required depends on the degree of hardness of your tap water. See Table 1. 1 Open the door and turn the unit on using the [ON/OFF] button. 2 Hold down the "A" button (see page 4) and press [START] until the display indicates "H:00". 3 Release both buttons. 4 Press the "C" button to select the desired setting. 5 Save the selected setting by pressing [START] and close the door. Using the water hardness test strip Dip the test strip into tap water for a second. Shake off excess water and wait approximately 1 minute before comparing results. After 1 minute the test strip will show you the correct setting Setting of internal water softener Fill water softener with salt? 0 H:00 no 1 H:00 no 2 H:02 yes 3 H:04 yes 4 H:06 yes Salt Refill the salt container, using a funnel to pour, right before turning on the unit to ensure that salt overflow is immediately washed away. This prevents corrosion. See Figure 1. 1 Open the screw cap of the salt container. 2 Fill the container with water (only required when turning on the unit for the first time). 3 Add dishwasher salt until the was is displaced and runs out. 4 Refill with salt as soon as the salt refill indicator is lit. Figure 1 Warning: Never fill the salt dispenser with detergent. It will destroy the water softening system. To prevent corrosion, refill with salt and immediately begin any cycle. Note: Refill salt only when the "Refill Salt" LED or the salt refill symbol is lit (model dependent). Do not use salt tablets or any salt other than dishwasher water softening salt. For more information about ordering salt please contact Customer Service. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64

6
Dishwasher Setup
Water Softening System
Your dishwasher requires soft water to ensure proper washing results
and is equipped with an internal water softening system. However, if
you have a household water softening system, the internal system pro-
vided is not needed.
For the water softening system to function properly, it will need to use
the dishwasher water softening salt. The amount of salt dispensed can
be set from “H:00” to “H:07”. Salt is not required at H:00 (this is the
default factory setting). The amount of salt required depends on the
degree of hardness of your tap water. See
Table 1
.
1
Open the door and turn the unit on using the
[ON/OFF]
button.
2
Hold down the
“A”
button (see page 4) and press
[START]
until
the display indicates
“H:00”
.
3
Release both buttons.
4
Press the
“C”
button to select the desired setting.
5
Save the selected setting by pressing
[START]
and close the door.
Using the water hardness test strip
Salt
Refill the salt container, using a funnel to pour, right before turning on the unit
to ensure that salt overflow is immediately washed away. This prevents corro-
sion. See
Figure 1
.
1
Open the screw cap of the salt container.
2
Fill the container with water (only required when turning on the unit for the
first time).
3
Add dishwasher salt until the was is displaced and runs out.
4
Refill with salt as soon as the salt refill indicator is lit.
Warning:
Never fill the salt dispenser with detergent. It will destroy the water
softening system. To prevent corrosion, refill with salt and immediately begin any cycle.
Note: Refill salt only when the “Refill Salt” LED or the salt refill symbol is lit (model dependent).
Do not use salt tablets or any salt other than dishwasher water softening salt.
For more information about ordering salt please contact Customer Service.
Dip the test strip into tap water for a second. Shake
off excess water and wait approximately 1 minute
before comparing results.
After 1 minute
the test strip will
show you the
correct setting
Setting of
internal
water
softener
Fill water
softener with
salt?
0
H:00
no
1
H:00
no
2
H:02
yes
3
H:04
yes
4
H:06
yes
Figure 1