Bosch WFL2090UC Installation Instructions
Bosch WFL2090UC - Axxis Series 24" High Efficiency Washer Manual
 |
UPC - 825225843702
View all Bosch WFL2090UC manuals
Add to My Manuals
Save this manual to your list of manuals |
Bosch WFL2090UC manual content summary:
- Bosch WFL2090UC | Installation Instructions - Page 1
Safety information d RISK OF INJURY! d The washing machine is heavy. Lift with caution. CAUTION Frozen hoses can tear/burst. Do not install the washing machine outdoors or in an area exposed to frost. Be sure to observe all listed warnings and cautions. These installation instructions are - Bosch WFL2090UC | Installation Instructions - Page 2
On the rear of the appliance: The bag contains: - Water drain hose. - Mains cable with plug. - Elbow for attaching the drain hose, e.g. into a wash basin. C = cold water connection H = hot water connection - Covers to be placed over the holes for the transport bolts (after removing it). - Wrench - Bosch WFL2090UC | Installation Instructions - Page 3
Dimensions a = 600 mm // 23 5/8" b = 590 mm // 22 1/2" c = 852 mm // 33 1/2" Approx. weight = 69 kg // 152 lbs. Installation area WARNING Never ground the washer to plastic plumbing lines, gas lines or hot water pipes. Appliance stability is important to make sure the washing machine does not walk - Bosch WFL2090UC | Installation Instructions - Page 4
washing machine must not wobble. a 570 mm minimum // 22 7/16" b 600 mm minimum // 23 5/8" c 850 mm minimum // 33 1/2" Minimum Installation mm) Note: Closet with dryer, please check the openings and ventilation requirements for the used dryer. Level the washing machine with the assistance of the - Bosch WFL2090UC | Installation Instructions - Page 5
screws 1, 2, 3 and 4 using the wrench until they can be moved freely. q Completely remove all transport bolts by reachĆ ing through the open washing machine door and pulling the drum slightly forward. Storing the transport bolts Always keep the transport bolts for future transĆ portation of the - Bosch WFL2090UC | Installation Instructions - Page 6
connection Water supply CAUTION The washing machine must only be operated with cold and hot (max. 140 °F // 60 °C) tap water. Do not connect the appliance to the mixer tap of an unpressurized hotĆwater boiler. If in any doubt, have the water connection installed by an authorized technician. The - Bosch WFL2090UC | Installation Instructions - Page 7
CAUTION Do not bend or pull the water drainage hose. Height difference between the placement area of washer and the drainage point: Maximum 110 cm // 43 inches. Standpipe or In Wall Installation or Cold water connection only with YĆpiece min. 10 mm q Use the UĆbracket. Attach the UĆbracket to - Bosch WFL2090UC | Installation Instructions - Page 8
be connected to an individual branch circuit and using a propĆ erly installed socket outlet which is grounded. The mains voltage must correspond to the voltage specification on the washing machine (nameplate). Connection specifications as well as the required fuses are stipulated on the appliance - Bosch WFL2090UC | Installation Instructions - Page 9
use an extention cord or an adapter to connect the washer to the electrical power supply. In the event that 22), - Disconnect the washing machine from the mains. - Dismantle the supply and drainage hose, - Install all transport bolts. Having transported the appliance and ensured proper installation
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
 |
 |
26
Installation,
Connection
and Transportation
Safety
± information
d
RISK
± OF
± INJURY!
d
The
washing
machine
is
heavy.
Lift
with
caution.
CAUTION
Frozen
hoses
can
tear/burst.
Do
not
install
the
washing
machine
outdoors
or
in
an
area
exposed
to
frost.
Be
sure
to
observe
all
listed
warnings
and
cautions.
These
installation
instructions
are
intended
for
use
by
qualified
installers.
In
addition
to
these
instructions
the
washer
shall
be
installed:
-
In
the
United
States,
in
accordance
with
the
National
Electric
Code,
ANSI/NFPA70±~
latest
edition/State
and
Municipal
codes
and/or
local
codes.
-
In
Canada,
in
accordance
with
the
Canadian
Electric
Code
C22.1±~
latest
edition/State
and
Municipal
codes
and/or
local
codes.
If
the
washing
machine
is
located
in
a
room
which
will
be
exposed
to
temperatures
below
the
freezing
point,
or
if
it
is
located
in
a
cabin
that
is
being
shut
down
for
the
winter,
any
residual
water
in
the
pump
or
water
inlet
hose(s)
must
be
drained.
To
drain
the
pump
refer
to
page±20.
To
drain
the
water
hose(s)
refer
to
page±22.
Take
care
not
to
damage
the
washing
machine.
Do±not
hold
onto
protruding
parts
(e.g.±loading
door)
when
lifting.
In
addition
to
the
safety
information
listed
here,
the
local±water
and
electricity
supplier
may
have
special
requirements.
In
case
of
doubt,
have
the
appliance
connected
by
an
authorized
technician.
FactoryĆsupplied
± equipment
There
is
a
packet
of
accessory
parts
supplied
with±your
washer.
Check
to
make
sure
that
all
the
accessory
parts
supplied
for
your
model
are
there.
If
any
parts
are
missing
contact
your
dealer
immediately.
Inside
the
drum:
-
Water
supply
hoses
(cold
and
hot
water).
Any
dampness
lift
inside
the
drum
was
caused
by
the
final
testing
which
every
washing
machine
is
subject
to
before
leaving
the
factory.