Boss Audio SLIM10 User Manual
Boss Audio SLIM10 Manual
 |
View all Boss Audio SLIM10 manuals
Add to My Manuals
Save this manual to your list of manuals |
Boss Audio SLIM10 manual content summary:
- Boss Audio SLIM10 | User Manual - Page 1
- Boss Audio SLIM10 | User Manual - Page 2
for choosing our product! Please read the instructions carefully so you will know how to operate your product properly. If there are any technical questions, please contact: Customer care: (805) 751-4853 & Live chat Online support: www.bossaudio.com/support IMPORTANT Please enter below the Serial No - Boss Audio SLIM10 | User Manual - Page 3
Input Wiring ...7 Power Connection ...8 Subwoofer Level Control Connection...9 Troubleshooting...9 Specifications...11 Introduction This product is designed as a car x Remote subwoofer level control • 4 x mounting brackets, 8 x screws • 1 x spare ATO fuse (25A) • User manual and warranty card - 2 - - Boss Audio SLIM10 | User Manual - Page 4
use your product. If you do not follow the instructions in this manual, we are not responsible for injury or damage resulting damage to the system. • Servicing must only be carried out by a technician. Contact our technical support for any service question. Installation precautions • WARNING: - Boss Audio SLIM10 | User Manual - Page 5
Panel Controls and Features 11 10 9 8 7 6 5 4 3 2 1 1. Power terminals GND: Connect to the closest point on the chassis of your vehicle. REM: Connect to the remote output wire of your head unit. No need to make the remote connection if you use high-level input connection and auto power on - Boss Audio SLIM10 | User Manual - Page 6
LED: the subwoofer is in protection mode and not operational. This problem is caused by input overload, short circuit or high temperature. maximum unless your input level requires it. • Failure to notice these instructions will result in an input overload to the subwoofer and excessive audio - Boss Audio SLIM10 | User Manual - Page 7
Protection Mode When protection mode triggers, the red LED on the subwoofer turns on and the subwoofer shuts down. One of the following reasons can trigger protection mode: input overload, short circuit and extremely high temperature. When the red LED turns on, take the following measures. • Check - Boss Audio SLIM10 | User Manual - Page 8
Wiring See the section "Installation precautions" on page 3. For safety, disconnect the negative terminal of the vehicle battery prior to wiring. Use only high quality wires for reliable installation to minimize signal or power loss. Make sure wires are not squeezed or damaged by sharp edges. Use - Boss Audio SLIM10 | User Manual - Page 9
Black To the closest chassis point Gray Blue White Red L+ To the speaker wires L- of your head unit R+ R- • Using the supplied high-level input wire harness, connect the black wire to the closest point on the metal frame (chassis) of your vehicle, and connect the other four colored wires to - Boss Audio SLIM10 | User Manual - Page 10
similar location where using it will not distract the driver. Troubleshooting If you have problems using this product, check the following points before you request service. If you still have a problem, contact our technical support. Problem No power Solution Check that the subwoofer is properly - Boss Audio SLIM10 | User Manual - Page 11
Problem Protection/Red LED lights up No sound Low output Hissing sound Squealing noise it off and on again. If the protection still lights up, the subwoofer is faulty and needs servicing. Check that audio input connection is correctly and securely made. If using low-level input connection, check - Boss Audio SLIM10 | User Manual - Page 12
Specifications Audio Output power 1000 high output Driver size 10" Speaker impedance 2.6Ω Total harmonic distortion (THD 4% Frequency response 20Hz - 150Hz Signal-to-noise ratio 68dB Input sensitivity 50mV (low level/RCA); 0.3V (high level) Low pass filter (LPF 50Hz - 150Hz Bass boost 0 to - Boss Audio SLIM10 | User Manual - Page 13
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
 |
 |
