Brother International BAS-310 Programmer Instruction Manual - English
Brother International BAS-310 Manual
View all Brother International BAS-310 manuals
Add to My Manuals
Save this manual to your list of manuals |
Brother International BAS-310 manual content summary:
- Brother International BAS-310 | Programmer Instruction Manual - English - Page 1
PROGRAMMABLE ELECTRONIC PATTERN SEWER WITH CYLINDER BED PROFILE S III PROGRAMMER INSTRUCTION MANUAL BAS-304 - Brother International BAS-310 | Programmer Instruction Manual - English - Page 2
sections 16 is To program a stitch pattern by tracing the design 17 E To program a design with recurring patterns 18 is To program a zigzag sewing operation 19 is To program enlargement/reduction patterns 23 E If a command key is pressed accidentally 23 HOW TO WRITE DATA TO DISK 24 Ej - Brother International BAS-310 | Programmer Instruction Manual - English - Page 3
is pressed, i.e., only if they are operating properly. Feed key After the thread trimming operation is completed this key is to be used if the sewing operation is not to be restarted immediately following the position at which the thread trimming operation was performed. Mirror key This key is to be - Brother International BAS-310 | Programmer Instruction Manual - English - Page 4
is used. • It also indicates the various numerical input commands. • If the programmable sewing speed becomes Fess than 500 spm while in the ( ) mode, the display will . Program key This switch is to be used to select either the sewing mode or the program mode. Reset key If this key is pressed - Brother International BAS-310 | Programmer Instruction Manual - English - Page 5
press the key (program key) to enter the program mode. When programming is completed, press the [1] key again to cancel the program mode and enable sewing. - Brother International BAS-310 | Programmer Instruction Manual - English - Page 6
direction. (2) Turn the power switch Q on. /1 (3) Manually rotate the pulley to move the needle point along the stitch pattern. Outline of the needle movement Bring into close proximity Cautions on sewing • The sewing speed of this machine is automatically regulated according to the stitch - Brother International BAS-310 | Programmer Instruction Manual - English - Page 7
to the initial stitch position. (7) Press the R/W switch to write the pattern to disk. (Refer to page 24.) Press the key to enter the sewing mode. To program with the enlarged input mode • Programming a fine pattern stitch by stitch is simplified by enlarging the pattern and entering it with - Brother International BAS-310 | Programmer Instruction Manual - English - Page 8
to the initial stitch position. (11) Press the R/W switch to write the pattern to disk. (Refer to page 24.) Press the [1] key to enter the sewing mode. -6- - Brother International BAS-310 | Programmer Instruction Manual - English - Page 9
work clamp to the initial stitch position. (X-0, Y-0) ® El • - 030- • E•"789".E O0 Any desired point (3) Use the direction keys to position the needle at sewing g start position 0 on the pattern, and then press the key. The first stitch is now programmed. (4) Use the numeral keys to enter the - Brother International BAS-310 | Programmer Instruction Manual - English - Page 10
stitch position. (18) Press the RAN switch to write the pattern to disk. "789" • • "111"• (Refer to page 24.) Press the [1) key to enter the sewing mode. Note 1 Note 2 At corners such as © and 0, be sure to break the pattern. If the pattern is not broken, these corners will also be - Brother International BAS-310 | Programmer Instruction Manual - English - Page 11
light. (2) Use the direction keys to move the work clamp to the initial stitch position. (3) Use the direciton keys to position the needle at the sewing start position 0 on the pattern, and then press ID key. The first stitch is now programmed. (4) Use the numerical keypad to display "2OO" in - Brother International BAS-310 | Programmer Instruction Manual - English - Page 12
operation • After the thread trimming operation is completed, if the sewing operation is to be continued without lifting the work clamp, use the Ej key (Feed key) to facilitate the R/W switch to write the pattern to disk. (Refer to page 24.) Press the 0 key to enter the sewing mode. Pattern 2 - Brother International BAS-310 | Programmer Instruction Manual - English - Page 13
light. (2) Use the direction keys to move the work clamp to the initial stitch position. (3) Use the direction keys to position the needle at the sewing start position ® on the pattern, and then pess the g key. The first stitch is now programmed. g (4) Use the direction keys and key to program - Brother International BAS-310 | Programmer Instruction Manual - English - Page 14
M key, and then press the key. (6) Press the R/W switch to write the pattern to disk. (Refer to page 24.) Press the key to enter the sewing mode. Note 1 Note 2 When the key is used to compose a symmetrical mirror image, the program will be input with the initial stitch position as the - Brother International BAS-310 | Programmer Instruction Manual - English - Page 15
to the initial stitch position. (9) Press the R/W switch to write the pattern to disk. (Refer to page 24.) Press the El key to enter the sewing mode. Repeat Y-axis (442), origin point (440), and X-axis (441) to program pattern (443). (X-0, Y-0) -111- (11 • "442" "440" "441" "443 - Brother International BAS-310 | Programmer Instruction Manual - English - Page 16
to the initial stitch position. (9) Press the R/W switch to write the pattern to disk. (Refer to page 24.) >K Press the [I] key to enter the sewing mode. Repeat Y-axis (442), origin point (440), and X-axis (441) to program pattern (443). 0 (X-0, Y-0) 0 "111" • E] Ei • "442" • "440" "441" "443 - Brother International BAS-310 | Programmer Instruction Manual - English - Page 17
to To input a split program • This is a method of programming an independent sewing operation or a sequential sewing operation of a pattern subdivided into smaller portions. Example: Program the pattern in the figure at pattern to disk. (Refer to page 24.) Press the E key to enter the sewing mode. - Brother International BAS-310 | Programmer Instruction Manual - English - Page 18
mode. (Operation) 0 Set the work piece as shown in the figure above, and press the starting pedal. 0The sewing machine will sew from 0 to ®, the thread will be cut at ®, the needle will rise, and the machine will stop. Remove the work clamp (inner clamp), and press the starting pedal again. 0 The - Brother International BAS-310 | Programmer Instruction Manual - English - Page 19
programming operation is performed according to the regular procedure, the first 1 stitch and the last 2 stitches will be automatically performed at low speed. If the sewing speed is to be reduced during the sewing operation (e.g., at acute angles), use the [] key (Load key) to perform a low speed - Brother International BAS-310 | Programmer Instruction Manual - English - Page 20
write the pattern to disk. (Refer to page 24.) ▪ Press the El key to enter the sewing mode. Note 1 Note 2 Sections of the pattern, such as sharp corners or especially intricate areas, which require special care when sewing should be programmed with the El key. g The El and keys can be used during - Brother International BAS-310 | Programmer Instruction Manual - English - Page 21
. The command indicator "F" will illuminate. (6) Operate the direction keys to move the work clamp to the proper sewing position. (7) Align the tip of the needle with the position at which the sewing operation © is to be performed. Then, press the key. (8) Press the numeral key 0 3 times to indicate - Brother International BAS-310 | Programmer Instruction Manual - English - Page 22
"770" on the STEP display. Note Set the zigzag width and stitch length so that areas corresponding to ( )number 0 to 9 are positive numbers. g (5) Press the key. to disk. (Refer to page 24.) Press the EJ key to enter the sewing mode. Note The E1 key is to be pressed, only at procedure 5 mentioned - Brother International BAS-310 | Programmer Instruction Manual - English - Page 23
the 1 key. The command indicator "F" will illuminate. (9) Operate the direction keys to move the work clamp to the initial stitch position of the next sewing operation. (10) Press the E key when the tip of the needle becomes aligned with the initial stitch position (11) Operate the direction keys so - Brother International BAS-310 | Programmer Instruction Manual - English - Page 24
the El key. The command indicator "F" will illuminate. (16) Operate the direction keys to move the work clamp to the initial position of the next sewing operation. (17) Press the 0 key when the tip of the needle becomes aligned with the initial.stitch position ®. (18) Indicate the proper pitch on - Brother International BAS-310 | Programmer Instruction Manual - English - Page 25
the 1 key. The command indicator "F" will illuminate. (9) Operate the direction keys to move the work clamp to the initial stitch position of the next sewing operation. (10) Press the key when the tip of the needle becomes aligned with the initial stitch position (11) Operate the direction keys so - Brother International BAS-310 | Programmer Instruction Manual - English - Page 26
at which "888" EI key was pressed as the reference point. Note 2 If the stitch length of an enlarged pattern exceeds 8.0 mm, or if the sewing area exceeds X = 50 mm and Y = 50 mm, all indicators will go out, and enlargement/reduction will be terminated. If this happens, use a different ratio and - Brother International BAS-310 | Programmer Instruction Manual - English - Page 27
written to disk. When the indicator 0 goes out, an alarm will sound to indicate the program was successfully written. Press the (I) key to enter the sewing mode. a (Back side) Slide the write protect tab 0 down after writing data to disk. Data cannot be written to or erased from disk when the - Brother International BAS-310 | Programmer Instruction Manual - English - Page 28
move from point 4 -. 5' - 6' - 7'- 8. (12) Press the R/W switch to write the pattern to disk. (Refer to page 24.) (13) Press the El Ice r to enter the sewing mode. - Brother International BAS-310 | Programmer Instruction Manual - English - Page 29
second stitch position. (6) Press the R/W switch to write the pattern to disk. (Refer to page 24.) (7) Press the key to enter the sewing mode. El To cancel the initial stitch of a pattern and reprogram the newly-established initial stitch position 2 34 5 6 (X-0 • Y-0) (1) Set the power source - Brother International BAS-310 | Programmer Instruction Manual - English - Page 30
position 1 will be programmed. (10) Press the R/W switch to write the pattern to disk. (Refer to page 24.) (11) Press the key to enter the sewing mode. To program a shunting point prior to the initial stitch position of the pattern which has already been programmed. In the event that work clamp - Brother International BAS-310 | Programmer Instruction Manual - English - Page 31
newly-established shunting point B. (8) Press the R/W switch to write the pattern to disk. (Refer to page 24.) (9) Press the key to enter the sewing mode. E To cancel the shunting point A • 01 2 3 4 5 6 7 (1) Set the power source switch to the ON position. (2) Press theEl key. The work clamp - Brother International BAS-310 | Programmer Instruction Manual - English - Page 32
move the tip of the needle to the newly-established starting position of the sewing operation. Then, press the 111 key. (5) Press the R/W switch to easily be brought to this position when the pulley is turned manually. (11) Turn the pulley manually to raise the needle to the highest position. (12) - Brother International BAS-310 | Programmer Instruction Manual - English - Page 33
(7) above to move the needle tip to point 3, and use the "777 F " code to return pattern C to its original position. (8) Press the R/W switch to write the enter the sewing mode. El To set a constant sewing speed irrespective of stitch length • The sewing speed on this machine is normally - Brother International BAS-310 | Programmer Instruction Manual - English - Page 34
g When thread trimming is not used at the sewing end Basting can be ended without thread trimming. M. The distance from C) to C) is the length of one stitch. (4) Feed to any point O. If the machine is not fed to add a point © after the last stitch 0, thread trimming will be performed at point 0. (5) - Brother International BAS-310 | Programmer Instruction Manual - English - Page 35
HOW TO USE AND MAINTAIN THE FLOPPY DISK -) Follow the suggestions mentioned below to obtain the maximum useful life of the micro disk. 1 Do not touch the magnetic surface of the memory disc. Fingerprints not only cause the disk to become dirty, but also always cause an error in the program. :.:.,:i - Brother International BAS-310 | Programmer Instruction Manual - English - Page 36
BROTHER INDUSTRIES, LTD. NAGOYA, JAPAN 151-304 192304-012 1990,9B C) Printed in Japan
PROGRAMMABLE
ELECTRONIC
PATTERN
SEWER
WITH
CYLINDER
BED
PROFILE
S
III
PROGRAMMER
BAS
-304
INSTRUCTION
MANUAL