Brother International DreamMaker„ XE VE2200 Users Manual - English
Brother International DreamMaker„ XE VE2200 Manual
View all Brother International DreamMaker„ XE VE2200 manuals
Add to My Manuals
Save this manual to your list of manuals |
Brother International DreamMaker„ XE VE2200 manual content summary:
- Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 1
Operation Manual Embroidery Machine Product Code: 882-D80/D82 Be sure to read this document before using the machine. We recommend that you keep this document nearby for future reference. - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 2
damages (including, but not limited to, procurement of substitute goods or services; loss of use, data, or profits; or business interruption) however caused . Each company whose software title is mentioned in this manual has a Software License Agreement specific to its proprietary programs - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 3
Please read these safety instructions before attempting to use the machine. DANGER - To reduce the risk of electrical shock 1 Always unplug the machine from the electrical outlet immediately after using, when cleaning, making any user servicing adjustments mentioned in this manual, or if you are - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 4
INSTRUCTIONS suffocation. • Do not use outdoors. 8 For a longer service life: • When storing this machine, avoid direct sunlight troubleshooting table in the back of the operation manual to inspect and adjust the machine yourself. If the problem persists, please consult your local authorized Brother - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 5
above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 6
908) 704-1700 declares that the product Product Name: Model Number: Brother Sewing Machine VE2200, BP2100 This device complies with Part 15 of the FCC Rules. and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 7
supplied sensor pen Page B-52 E Embroidering This section provides instruction to embroider designs with this machine. Chapter 1, "Embroidery", how to create bobbin work Page A-2 Chapter 2 Maintenance and Troubleshooting Find troubleshooting tips and pointers as well as how to keep your machine - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 8
CONTENTS CONTENTS TRADEMARKS INTRODUCTION 1 IMPORTANT SAFETY INSTRUCTIONS 1 WHAT YOU CAN DO WITH THIS MACHINE ..... 5 NAMES OF MACHINE FUNCTIONS 57 SELECTING PATTERNS TO EDIT 58 Selecting Embroidery Patterns/Brother "Exclusives"/Floral Alphabet Patterns/Frame/Bobbin Work Patterns 59 Selecting - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 9
the Maintenance Message 17 ADJUSTING THE SCREEN 18 Adjusting the Brightness of the Screen Display 18 Touch Panel is Malfunctioning 18 TROUBLESHOOTING 19 ERROR MESSAGES 22 SPECIFICATIONS 25 UPGRADING YOUR MACHINE'S SOFTWARE ..... 26 Upgrade Procedure Using USB Media 26 Upgrade Procedure Using - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 10
bobbin. b Pre-tension disk Pass the thread around the pre-tension disk when winding the bobbin thread. (page B-31) c Thread guide for bobbin winding Pass the thread through this thread guide when winding the bobbin thread. (page B-31) d Spool pin Place a spool of thread on the spool pin. (page B-38 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 11
B-36) d Needle plate cover Remove the needle plate cover to clean the race. (page E-22) e Needle plate f Needle bar thread guide Pass the upper thread through the needle bar thread guide. (page B-38) g Needle clamp screw Use the needle clamp screw to hold the needle in place. (page B-45) a Carriage - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 12
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS Operation Buttons a "Start/Stop" button Press this button to begin embroidering. The button changes color according to the machine's operation mode. Green: The machine is ready to embroider or is embroidering. Red: The machine cannot embroider. b " - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 13
Included Accessories 1* 2* 3 4 NAMES OF MACHINE PARTS AND THEIR FUNCTIONS 5 6 7 8 75/11 3 needles 90/14 1 needle 75/11 2 needles 9 10 11 12* 13 14 15 16 17* 18* 19 20 21 22 23* 24 25* 26* 27 28 29* 30* 31* 32 33 34 35 *Included accessories vary depending on the - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 14
W 18 cm (H 12 inches × W 7 inches) SA440 EF76: XC8482-152 28 Brother poly #90 bobbin thread EBT-PE EBT-PEN: XC5996-001 29 Stabilizer material* SA519 XF4569-001 33 Accessory bag XC4487-021 34 Operation manual This manual 35 Quick Reference Guide XF3841-001 (882-D80) XF3637-001 (882-D82 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 15
AND THEIR FUNCTIONS Options The following are available as optional accessories to be purchased separately from your authorized Brother dealer. 1 2 3 4 5 6 7 8 9 10 11 No. Part Name 1 Square embroidery frame H 15 cm x W 15 cm (H 6 inches x W 6 inches) 2 Embroidery foot "W+" with - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 16
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS B-14 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 17
Basic operations This section provides details on the initial setup procedures as well as descriptions of this machine's more useful functions. Page number starts with "B" in this section. Chapter1 Getting Ready B-16 Chapter2 Sensor Functions (For models equipped with the sensor function B-52 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 18
18 LCD SCREEN 20 ■ Home Page Screen 20 ■ Key Functions 21 Using the Machine Setting Mode Key 22 ■ Selecting the "Eco Mode" or "Shutoff Support Mode 25 ■ Changing the Pointer Shape When a USB Mouse Is Used ........ 25 ■ Selecting the Initial Screen Display 25 ■ Choosing the Display Language 26 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 19
unattended, either the main switch of the machine should be turned to OFF or the plug must be removed from the socket-outlet. • When servicing the machine or when removing covers, the machine must be unplugged. • For U.S.A. only This appliance has a polarized plug (one blade wider than the other - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 20
TURNING THE MACHINE ON/OFF a Insert the power supply cord into the power cord receptacle, then insert the plug into a wall outlet. Setting Your Machine for the First Time When you first turn on the machine, set the language and time/date to your language and local time/date. Follow the - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 21
d Press or to set time/date. a b c d a Press to display the time on the screen. b Set the year (YYYY), month (MM) and date (DD). c Select whether 24h or 12h setting to display. d Set the current time. e Press to start using your machine. → The clock starts from 0 second of the time you set. - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 22
LCD SCREEN LCD SCREEN CAUTION • Only touch the screen with your finger or the included touch pen. Do not use a sharp pencil, screwdriver, or other hard or sharp object. It is not necessary to press hard on the screen. Pressing too hard or using a sharp object may damage the screen. ■ Home Page - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 23
■ Key Functions LCD SCREEN a B 1 Getting Ready ed c b No. Display Key Name Explanation Page a Home page screen Press this key anytime it is displayed to return to the home page screen and B-20 key select a different category - "Embroidery" or "Embroidery Edit". b Clock key Press - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 24
. Increase the number for louder volume, decrease for softer volume. f Select to save the machine power by setting the "Eco Mode" or the "Shutoff Support Mode" (see page B-25). g Select the initial screen that is displayed when the machine is turned on (see page B-25). h Change the display language - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 25
see page B-56). d Display the service count which is a reminder to take your machine in for regular servicing. (Contact your authorized dealer for details.) machine. Check with your local authorized Brother dealer or at " http://solutions.brother.com " for available updates (see page A-26). - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 26
LCD SCREEN g k h l a m b i c d e j f a Select from among 16 embroidery frame displays (see page E-35). b Change the thread color display on the "Embroidery" screen; thread number, color name (see page E-34). c When the thread number "#123" is selected, select from six thread brands ( - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 27
. Touch the screen or any operational button to continue sewing. "Shutoff Support Mode"; Machine will turn off after set period of time. Turn machine the machine while the machine is in the "Eco Mode" or the "Shutoff Support Mode", wait for about 5 seconds before turning on the machine again. LCD - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 28
LCD SCREEN c Use initial or screen to select display. the setting for the * Opening Screen: When the machine is turned on, the home page screen appears after the opening movie screen is touched. * Home Page: When the machine is turned on, the home page screen appears. * Embroidery Screen: - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 29
d Select the background settings available. color from the 66 a LCD SCREEN ■ Specifying the Size of Pattern Thumbnails The thumbnails for selecting an embroidery pattern B can be set to be displayed at the smaller size or a larger size. The larger size is 1.5 times the smaller size. 1 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 30
LCD SCREEN c Press or thumbnail size. to select the desired ■ Saving a Settings Screen Image to USB Media An image of the settings screen can be saved as a BMP file. A maximum of 100 images can be saved on a single USB media at one time. a Insert the USB media into the the right side of the - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 31
in the movies. Watch these movies for a embroidering, checking the tension, etc. better understanding of the functions. Certain individual threading screens are animated. information. displays troubleshooting displays information about cleaning the machine, etc. Basic operations B-29 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 32
b Press . → The lower half of the screen will change. c Press (upper threading). → The screen shows instructions for threading the machine. d Read the instructions. * To view video, press instructions. of the displayed Press under movie to go back to the beginning. Press to pause. Press - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 33
LOWER THREADING LOWER THREADING Winding the Bobbin Press → → → B ■ Using the Supplemental Spool Pin With this machine, you can wind the bobbin 1 without unthreading the machine. While using the main spool pin to sew, you can conveniently wind the bobbin using the supplemental spool pin. - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 34
the thread spool. With your left hand, near hold the end of the thread, and use both hands to pass the thread through the thread guide. a Thread guide B-32 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 35
the pre-tension disk. h Pass the end of the thread through the guide slit in the bobbin winder seat, and pull the thread to the right pre-tension disks. g Wind the thread clockwise bobbin 5-6 Times. around the a Guide slit (with built-in cutter) b Bobbin winder seat CAUTION • Be sure to - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 36
LOWER THREADING j Press . → Bobbin winding starts automatically. The bobbin stops rotating when bobbin winding is completed. The bobbin winding switch will automatically return to its original position. k Cut the thread with scissors and bobbin. remove the Note • changes to while the - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 37
the bobbin on the shaft. LOWER THREADING f Pass the thread through the thread guide. B 1 Getting Ready a Groove in the bobbin b Spring on the shaft so that the thread unwinds from the front of the spool. a Thread guide g Pass the thread around the pre-tension disk making sure that the thread - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 38
LOWER THREADING a If the thread becomes tangled under the bobbin winder seat, press once to stop the bobbin winding. b Cut the thread with pre-tension disk. scissors near the Setting the Bobbin Press → → → in this order to display a video example of the operation on the LCD (see page - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 39
THREADING e While lightly holding down bobbin with your right hand as shown, guide the thread through the slit (a and b). * At this time, check around the tab with your left hand as shown, lightly pull the thread to guide it through the slit. a Slit b Cutter (Cut the thread with the cutter - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 40
UPPER THREADING UPPER THREADING Upper Threading b Press the "Presser Foot raise the presser foot. Lifter" button to Press → → → in this order to display a video example of the operation on the LCD (see page B-30). Follow the steps explained below to complete the operation. CAUTION • Be - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 41
that f While holding the pull the thread up thread with both hands, from under the thread the thread unwinds from the front of the spool. guide plate. B 1 Getting Ready a Spool pin b Spool cap c Thread spool d Spool felt e Push the spool cap onto the spool pin as far as possible, then - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 42
in the illustration. l Pull the thread up through the thread cutter to cut the thread, as shown in the illustration. a Needle bar thread guide j Press the "Presser Foot lower presser foot. Lifter" button to a Thread cutter Note • When using thread that quickly winds off the spool, such - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 43
be threaded with the needle threader. In this case, instead of B using the needle threader after passing the thread through the needle bar thread guide (marked "6"), manually pass the thread 1 through the eye of the needle from the front to the back. Getting Ready Note • Pulling the loop of - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 44
CHANGING THE EMBROIDERY FOOT CHANGING THE EMBROIDERY FOOT Either embroidery foot "W+" with LED pointer or "W" is included depending on the countries or regions. The embroidery foot is attached to the machine when purchased, with the connector of the embroidery foot "W+" with LED pointer unplugged - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 45
CHANGING THE EMBROIDERY FOOT a Position the embroidery foot "W+" with LED pointer or "W" on the presser foot bar d Press to unlock all keys and by aligning the notch of the presser foot to the large screw. Side view buttons. → All keys and operation buttons are unlocked, and the previous - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 46
CHANGING THE EMBROIDERY FOOT ■ Adjusting the LED Pointer (For Embroidery foot "W+" with LED pointer user only) Adjust the LED pointer if it indicates a point different than the actual needle drop point. Before adjusting the LED pointer, mark the actual needle drop point on the fabric to be - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 47
CHANGING THE NEEDLE CHANGING THE NEEDLE CAUTION • Always press on the screen before changing the needle. If is not pressed and the Start/Stop button or another operation button is pressed accidentally, the machine will start and injury may result. • Use only embroidery machine needles made - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 48
is probably the most important part of the machine. Choosing the proper needle for your embroidering project will result in a beautiful finish and fewer problems. Below are some things to keep in mind about needles. • Use needle 75/11 for embroidery. • It is recommended that a 90/14 needle should - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 49
BEFORE EMBROIDERING About the Embroidery Unit ■ Removing the Embroidery Unit a Press either (Embroidery) or (Embroidery Edit), then press . → The carriage will move to the removal position. CAUTION B • Do not carry the embroidery unit by holding the release button compartment. 1 Getting - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 50
BEFORE EMBROIDERING b Insert the embroidery unit connection into the machine connection port. The spring hinge on the connection port cover will allow easy access to the port. Push lightly on the connection port cover until the unit clicks into place. a Embroidery unit connection b Machine - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 51
force. Check the orientation of the connector. • For details on the position of the USB port on the computer (or USB hub), refer to the instruction manual for the corresponding equipment. Basic operations B-49 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 52
of operations in the screens. Note • If a mouse other than the optional USB mouse is used, it may not perform as described in this Operation Manual. ■ Changing Pages Rotate the mouse wheel to switch through the tabs of the pattern selection screens. Memo • If page numbers and a vertical scroll bar - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 53
Getting Ready USING FUNCTIONS BY CONNECTING THE ACCESSORY TO THE MACHINE B 1 Basic operations B-51 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 54
BBasic operations 2 Chapter Sensor Functions (For models equipped with the sensor function) You can activate this function after connecting the sensor pen to the machine. The sensor pen is included with the machine in some countries or regions. CONNECTING THE SENSOR PEN 53 Using the Sensor Pen - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 55
CONNECTING THE SENSOR PEN CONNECTING THE SENSOR PEN B When connecting the sensor pen to the machine, make sure that the arrow on the sensor pen connector faces up, lines up with the arrow on the machine, and that the connector is firmly inserted into the jack. 2 a Using the point end of the - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 56
CONNECTING THE SENSOR PEN c Set the sensor pen in the sensor pen holder with the pen tip pointing downward, and then connect the sensor pen to the machine. B-54 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 57
correctly read. • Do not drag the sensor pen tip on the machine, otherwise the sensor pen tip may be chipped off. • If there is any problem with the guideline marker, the sensor function may not operate correctly. Memo • The sensor pen can be used to touch on the screen as a touch - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 58
USING THE SENSOR PEN Calibrating the Sensor Pen d First touch the green dot marking on the needle plate cover using the sensor pen. Before using the sensor pen for the first time be sure to calibrate it to the screen. Doing so allows the machine to learn the position you usually hold a pen. Hold - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 59
Sensor Functions (For models equipped with the sensor function) f Press repeat the to finish the calibration. To calibration touch the first point again using the sensor pen, and continue with step e. USING THE SENSOR PEN B 2 * Press to return to the original screen without finishing the - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 60
USING SENSOR FUNCTIONS IN "EMBROIDERY"/"EMBROIDERY EDIT" MODE USING SENSOR FUNCTIONS IN "EMBROIDERY"/"EMBROIDERY EDIT" MODE Before using the sensor functions, carefully read the procedure in "Embroidery" and "Embroidery Edit" to familiarize yourself with the machine operations. Specifying the - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 61
h Press . USING SENSOR FUNCTIONS IN "EMBROIDERY"/"EMBROIDERY EDIT" MODE c With the sensor pen, touch the point fabric corresponding to corner a in on the the screen. B 2 → The embroidering position selection screen appears. Sensor Functions (For models equipped with the sensor function) i - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 62
USING SENSOR FUNCTIONS IN "EMBROIDERY"/"EMBROIDERY EDIT" MODE f Press to move the LED pointer on the fabric for adjusting the first position. ■ Selecting the Embroidering Position by the Pattern Center a Press in the following screen. g Press to apply the setting. h Press to move the LED - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 63
Sensor Functions (For models equipped with the sensor function) USING SENSOR FUNCTIONS IN "EMBROIDERY"/"EMBROIDERY EDIT" MODE d Press to move the LED pointer B on the fabric for adjusting the first position. 2 e Press to apply the setting. f Press to move the LED pointer on the fabric for - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 64
USING SENSOR FUNCTIONS IN "EMBROIDERY"/"EMBROIDERY EDIT" MODE B-62 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 65
Embroidering This section provides instruction to embroider designs with this machine. Page number starts with "E" in this section. The screen display and machine illustration may vary slightly, depending on the countries or regions. Chapter1 Embroidery E-2 Chapter2 Embroidery Edit E-56 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 66
E Embroidering 1 Chapter Embroidery SELECTING PATTERNS 3 ■ Copyright Information 3 Selecting Embroidery Patterns/Brother "Exclusives"/Floral Alphabet/Bobbin Work Patterns 4 Selecting Character Patterns 5 Selecting Frame Patterns 7 Selecting Patterns from Embroidery Cards 7 ■ About Embroidery - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 67
patterns stored in the machine's memory (see the "Quick Reference Guide" for a full summary of patterns in the machine's memory). You . a b c d e f g h i j a Embroidery patterns b Brother "Exclusives" c Floral alphabet patterns d Frame patterns e Character patterns f Bobbin work - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 68
SELECTING PATTERNS Selecting Embroidery Patterns/Brother "Exclusives"/Floral Alphabet/Bobbin Work Patterns c Press to create a mirror image of the pattern as needed. * If a mistake has been made when selecting the pattern, - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 69
Selecting Character Patterns Example: Entering "We Fly". a Press . b Press the key embroider. of the font you want to SELECTING PATTERNS * If you want to change the size of a character, select the character and then press to change the size. The size changes each time you press the - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 70
SELECTING PATTERNS g Press again and enter "F". i Press . h Press and then enter "ly". → The embroidery screen is displayed. j Proceed to "VIEWING THE EMBROIDERING SCREEN" on page E-9 to embroider the pattern. * To return to the previous screen to select another pattern, press . E-6 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 71
Selecting Frame Patterns a Press . SELECTING PATTERNS e Proceed to "VIEWING THE EMBROIDERING SCREEN" on page E-9 to embroider the pattern. E * To return to the previous screen to select another pattern, press . 1 Embroidery b Press the key to embroider of in the the frame shape - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 72
SELECTING PATTERNS a Plug the optional embroidery card Reader/USB card writer module into the USB port on the machine. c Press the key of the USB port. a USB port b Embroidery card Reader/USB card writer module b Insert the card completely into the Reader/USB card writer module. card * - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 73
VIEWING THE EMBROIDERING SCREEN VIEWING THE EMBROIDERING SCREEN E hi a j 1 b k Embroidery c l d e m f g a Shows the presser foot code. Attach embroidery foot "W+" or "W" for all embroidery projects. When the foot presser symbol is displayed on the screen, you are able to sew. b - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 74
VIEWING THE EMBROIDERING SCREEN ■ Key Functions Using these keys, you can change the size of the pattern, rotate the pattern, etc. Note Q • Some operations or functions are not available for certain patterns. If the key display is light gray, you cannot use that function or operation with the - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 75
Iron-on Stabilizers (Backing) to the Fabric For best results in your embroidery projects, always use stabilizer material for embroidery. Follow the package instructions for the stabilizer being used. When using fabrics that cannot be ironed (such as towel or fabrics that have loops which expand when - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 76
PREPARING THE FABRIC b Iron the iron-on stabilizer wrong side of the fabric. material to the a Fusible side of stabilizer b Fabric (wrong side) Memo • When embroidering on thin fabrics such as organdy or lawn, or on napped fabrics such as towel or corduroy, use water soluble stabilizer (sold - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 77
PREPARING THE FABRIC Hooping the Fabric in the Embroidery Frame ■ Types of Embroidery Frames The types and numbers of supplied embroidery frame are differs depending on the countries and regions. E 1 Extra Large Large Medium Embroidery Embroidery field 30 cm × 18 cm (approx. 12 inches × 7 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 78
PREPARING THE FABRIC ■ Inserting the Fabric Note • If the fabric is not securely held in the embroidery frame, the embroidery design will sew out poorly. Insert the fabric on a level surface, and gently stretch the fabric taut in the frame. Follow the steps below to insert the fabric correctly. a - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 79
you made on the fabric. E 1 Embroidery Memo • You can use the included screwdriver when you loosen or tighten the frame adjustment screw. a Inner frame b Guide line c Gently stretch the fabric so folds or wrinkles, and press there are the inner no frame into the outer frame. ■ Using the - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 80
■ Embroidering Ribbons or Tape Secure with double-sided tape or a temporary spray adhesive. Use an embroidery stabilizer to provide extra support. After embroidering, remove the stabilizer carefully. Attach the stabilizer as shown in the following examples. We recommend using a stabilizer for - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 81
bobbin before attaching the embroidery frame. 1 Embroidery a Press the "Presser Foot raise the presser foot. Lifter" button to b Align the embroidery frame guide with the right edge of the embroidery frame holder. d Lower the frame-securing lever to be level with the frame to secure the - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 82
ATTACHING THE EMBROIDERY FRAME b Pull the embroidery frame toward you. E-18 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 83
CONFIRMING THE PATTERN POSITION CONFIRMING THE PATTERN POSITION E The pattern is normally positioned in the center of the embroidery frame. If the pattern needs to be repositioned for better placement on the garment, you can check the layout before starting embroidery. 1 Embroidery Checking - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 84
CONFIRMING THE PATTERN POSITION Previewing the Completed Pattern a Press . → An image of the pattern as it will be embroidered appears. b Press used in the preview. to select the frame * Frames displayed in light gray cannot be selected. * Press to enlarge the image of the pattern. * The - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 85
SEWING AN EMBROIDERY PATTERN SEWING AN EMBROIDERY PATTERN E Embroidery Attractive Finishes 1 There are many factors that go into beautiful embroidery. Using the appropriate stabilizer (see page E-11) and hooping the fabric in the frame (see page E-13) are two important factors mentioned earlier - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 86
SEWING AN EMBROIDERY PATTERN ■ Embroidery Needle Plate Cover Under some conditions, based on the type of fabric, stabilizer, or thread being used, there may be some looping in the upper thread. In this case, attach the included embroidery needle plate cover to the needle plate. Attach the cover by - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 87
b Lower the presser foot, then press the "Start/Stop" button to start embroidering. After 5-6 stitches, press the "Start/Stop" button again to stop the machine. c Trim the excess thread at the end of the seam. If the end of the seam is under the presser foot, raise the presser foot, then trim - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 88
SEWING AN EMBROIDERY PATTERN a Attach side of an iron-on stabilizer to the appliqué material. the wrong d Place the frame. base material into the embroidery a Appliqué material (cotton, felt, etc.) b Iron-on stabilizer b Place the appliqué material into the embroidery frame, and then - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 89
g Press the "Start/Stop" button. Memo • Some patterns may not show all three appliqué steps. Sometimes the "APPLIQUE" step will be shown as a color. → The appliqué will then be completed. h Change the rest the upper thread and of the embroidering. then carry out SEWING AN EMBROIDERY PATTERN - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 90
ADJ USTMENTS DURING THE EMBROIDERY PROCESS ADJUSTMENTS DURING THE EMBROIDERY PROCESS Note • Be careful not to bump the embroidery unit carriage or the presser foot when removing or attaching the embroidery frame. Otherwise, the pattern will not embroider correctly. If the Bobbin Runs Out of Thread - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 91
ADJ USTMENTS DURING THE EMBROIDERY PROCESS If the Thread Breaks During Sewing a Press the "Start/Stop" machine. button to stop the b If the upper thread is broken, redo the upper threading. If the bobbin thread is broken, press and follow the directions in steps a through e from the - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 92
stopped Note • Do not remove the embroidery unit or the memory will no longer remember your design. a Turn the main power to ON. b Follow the instructions shown on the and remove the embroidery frame. screen → The following message will appear. E-28 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 93
c Attach the embroidery frame and press . ADJ USTMENTS DURING THE EMBROIDERY PROCESS E 1 Embroidery → The previous embroidery screen displayed before the machine was turned off appears. Memo • If you want to start a new embroidery pattern, press so the pattern selection screen appears. d - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 94
MAKING EMBROIDERY ADJUSTMENTS MAKING EMBROIDERY ADJUSTMENTS Adjusting Thread Tension a Press . When embroidering, the thread tension should be set so that the upper thread can slightly be seen on the wrong side of the fabric. ■ Correct Thread Tension The pattern can be seen from the wrong side - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 95
MAKING EMBROIDERY ADJUSTMENTS b Press to tighten the upper thread To adjust the bobbin tension for embroidery function, using the bobbin case (with no color on tension. (The tension number will increase.) the screw), turn the slotted-head screw (-) with a (small) screwdriver. E 1 Embroidery - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 96
MAKING EMBROIDERY ADJUSTMENTS ■ Bobbin Thread is Too Tight a Press . Upper thread on the right side of fabric seems to be lifting/looping and bobbin thread is not seen on the wrong side of fabric. a Right side b Wrong side If this occurs, turn the slotted-head screw (-) counterclockwise, being - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 97
Note • When this function is turned on, use the included ball point needle 75/11 for embroidering patterns with short jump stitches such as alphabet characters. Using other needles may cause the thread to break. a Press . MAKING EMBROIDERY ADJUSTMENTS ■ Selecting the Length of Jump Stitch Not to - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 98
MAKING EMBROIDERY ADJUSTMENTS Memo • "spm" is the number of stitches sewn in one minute. • Decrease the sewing speed when embroidering on thin, thick, or heavy fabrics. • The sewing speed can be changed after an embroidery has been started. • The maximum sewing speed setting does not change until a - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 99
Changing the "Embroidery Frame Display" a Press . b In the "Embroidery Frame Display", use to change the embroidery frame display mode. * There are 16 choices. MAKING EMBROIDERY ADJUSTMENTS E 1 Embroidery * For the optional embroidery frame. a Extra large frame embroidering area 30 cm × 18 cm - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 100
REVISING THE PATTERN REVISING THE PATTERN CAUTION • When you have revised the pattern, check the display of available embroidery frames and use an appropriate frame. If you use an embroidery frame not displayed as available for use, the presser foot may strike the frame and possibly cause injury. - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 101
a Mark the embroidery fabric, as shown. start position on the REVISING THE PATTERN d Press . E e Use to align the needle and the mark on the fabric, and begin embroidering the 1 pattern. Embroidery b Press . Changing the Size of the Pattern a Press . c Press . a b a Start - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 102
REVISING THE PATTERN a a Size of the pattern Rotating the Pattern a Press . Memo • Some patterns or characters can be enlarged more than others. • Some patterns or characters can be enlarged to a greater degree if they are rotated 90 degrees. • You can change the size of the pattern by rotating - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 103
a Degree of rotation REVISING THE PATTERN Creating a Horizontal Mirror Image E Press so it appears as to create a 1 horizontal mirror image of the selected pattern. Press again to return the pattern to normal. Embroidery a 0° Memo • You can rotate the pattern by rotating the mouse wheel. - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 104
REVISING THE PATTERN Changing the Density (Alphabet Character and Frame Patterns Only) The thread density for some alphabet character and frame patterns can be changed. A setting between 80% and 120% in 5% increments can be specified. a Press . * Press to display all the function keys on the screen. - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 105
b After a character is sewn, change the thread color, and then sew the next character. b Press . REVISING THE PATTERN E 1 Embroidery Embroidering Linked Characters c Press . Follow the procedure described below to embroider linked characters in a single row when the entire pattern extends - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 106
REVISING THE PATTERN d Press . e Press . h After the characters are embroidered, cut the threads to a generous length, remove the embroidery frame, and then attach the embroidery frame again so that the remaining characters ("DEF") can be embroidered. f Press to turn off the thread - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 107
m Use to align the needle with the end of embroidering for the previous pattern. REVISING THE PATTERN E 1 Embroidery n Press the "Start/Stop" button to begin embroidering the remaining character patterns. → The thread color displayed on the screen will be grayed out. Uninterrupted - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 108
USING THE MEMORY FUNCTION USING THE MEMORY FUNCTION Embroidery Data Precautions Observe the following precautions when using embroidery data other than that created and saved in this machine. CAUTION • When using embroidery data other than our original patterns, the thread or needle may break when - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 109
USING THE MEMORY FUNCTION • Do not create folders in "Removable Disk" on a computer. If embroidery data is stored in a folder in "Removable Disk", that embroidery data cannot be retrieved by the machine. • Even if the embroidery unit is not attached, the machine will recognize embroidery data. ■ - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 110
USING THE MEMORY FUNCTION b Select the pattern you want to delete. Saving Embroidery Patterns to USB Media When sending embroidery patterns from the machine to USB media, plug the USB media into the machine's USB port. c Press . a b a Amount of memory used by the pattern to be deleted b Amount - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 111
force. Check the orientation of the connector. • For details on the position of the USB port on the computer (or USB hub), refer to the instruction manual for the corresponding equipment. Embroidering E-47 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 112
USING THE MEMORY FUNCTION c Press when the pattern you want to save is in the embroidery screen. Retrieving Patterns from the Machine's Memory a Press . d Press * Press saving. . to return to the original screen without → The machine displays the patterns currently in the memory. b Press - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 113
Recalling from USB Media You can recall a specific embroidery pattern from either direct USB media or a folder in the USB media. If the pattern is in a folder, check each folder to find the embroidery pattern. Note • The processing speed may vary by quantity of data. a Insert the USB media into - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 114
USING THE MEMORY FUNCTION Recalling from the Computer d Press . a Plug the USB cable connector into the corresponding USB ports for the computer and for the machine (see page E-47). b On the computer, open "Computer computer)" then go to "Removable (My Disk". → The patterns in the computer - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 115
EMBROIDERY APPLICATIONS EMBROIDERY APPLICATIONS E Using a Frame Pattern to Make an Appliqué (1) c Apply a thin layer of fabric glue or a temporary spray adhesive to the rear of the 1 appliqué created in step a. Attach the appliqué to the base fabric matching the Embroidery You can use - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 116
EMBROIDERY APPLICATIONS Using a Frame Pattern to Make an Appliqué (2) d Remove the embroidery frame from the embroidery unit, and cut around the outside of the stitches. This is a second method to make appliqué using embroidery patterns. You do not have to change the fabric in the embroidery - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 117
to create a single pattern after each section is sewn. For details on creating split embroidery patterns and for more detailed sewing instructions, refer to the Instruction manual included with PE-DESIGN Ver.7 or later, or PE-DESIGN NEXT. The following procedure describes how to read the split - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 118
EMBROIDERY APPLICATIONS c Press . e Press the "Start/Stop" the pattern section. button to embroider f When embroidering is finished, the following screen appears. Press . d If necessary, edit the pattern. → A screen appears so that a section of the split embroidery pattern can be - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 119
Embroidery EMBROIDERY APPLICATIONS E 1 Embroidering E-55 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 120
E Embroidering 2 Chapter Embroidery Edit EXPLANATION OF FUNCTIONS 57 SELECTING PATTERNS TO EDIT 58 Selecting Embroidery Patterns/Brother "Exclusives"/Floral Alphabet Patterns/Frame/Bobbin Work Patterns 59 Selecting Alphabet Character Patterns 59 EDITING PATTERNS 61 ■ Key Functions 62 Moving - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 121
EXPLANATION OF FUNCTIONS EXPLANATION OF FUNCTIONS E With the "Embroidery Edit" functions, you can combine embroidery patterns and character patterns, change the size of patterns, rotate patterns, and perform many other editing functions. This machine can perform the 9 functions listed below. 2 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 122
instructions on "BEFORE EMBROIDERING" of "Basic operations", and press , then to display the screen below. a b c d e f g h i j a Embroidery patterns b Brother unit for storage. Memo • See included "Quick Reference Guide" for more information on each category's selection screen. E-58 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 123
SELECTING PATTERNS TO EDIT Selecting Embroidery Patterns/Brother "Exclusives"/Floral Alphabet Patterns/Frame/Bobbin Work Patterns Selecting Alphabet Character Patterns E When you select character patterns from the "Embroidery Edit" screen, you can edit - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 124
SELECTING PATTERNS TO EDIT c Press to change the layout of the pattern. * If the characters are too small to see, press to view a display of all entered characters. f After you finish your selections, press . d Select the layout. (Example: ) When selecting an arc, use and to change the - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 125
EDITING PATTERNS d a a b b c e c EDITING PATTERNS E 2 d e Embroidery Edit a Shows the size of the entire combined pattern. b Shows the size of the pattern currently selected. c Shows the distance from the center of the frame. d Shows the color sequence and times of each step of the - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 126
EDITING PATTERNS ■ Key Functions a b c d fe g h i p no m l k j No. Display Key Name Explanation a Magnify key Press this key to magnify the pattern by 200% in the screen. Page E-63 b Thread palette key Press this key to change the colors of the displayed pattern. E-67 c Rotate key - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 127
EDITING PATTERNS Moving the Pattern Displaying Patterns in the Screen Magnified by 200% E For details on moving the pattern, refer to "Moving the Pattern" on page E-36. a Press . 2 Rotating the Pattern Embroidery Edit For details on rotating the pattern, refer to "Rotating the Pattern" - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 128
EDITING PATTERNS Changing the Configuration of Character Patterns a Press . Changing Character Spacing a Press . b Press the key embroider. of the layout you want to * See page E-60 for more information about layout types. b Use to change the spacing. * Press to increase the - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 129
not recommended to edit data and transfer to other or older version machines. Same features do not apply in other machines, so problems may occur. • Character spacing can be reduced only when characters are arranged normally on a straight line. Separating Combined Character Patterns E Combined - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 130
EDITING PATTERNS c Use to select where the pattern is to be separated, and then press to separate it. For this example, the pattern will be separated between "T" and "a". Changing the Color of Each Alphabet Character in a Pattern a Press so you can assign a thread color to each character. - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 131
EDITING PATTERNS Embroidering Linked Characters You can embroider linked characters exampled below, in a single row when the pattern extends beyond the embroidery frame. For details on embroidering linked characters, refer to "Embroidering Linked Characters" on page E-41. Example: Linking "DEF" to - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 132
Anton thread colors contained in the custom thread table. 300 Robison-Anton thread colors table data can be downloaded from our website " http://solutions.brother.com ". a In the pattern editing screen, press and then press . c Use to select one of the thread brands in the machine. d Use to - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 133
e Press . g Press EDITING PATTERNS to return to the original screen. E 2 Embroidery Edit b a a Thread brand b Entered thread color number → The selected thread color is set in the custom thread table. Note • If is not pressed, the thread color number will not be changed. f Repeat the - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 134
EDITING PATTERNS e Repeat the previous steps until thread colors are specified. all desired * To delete a specified color from the palette, select the color to be deleted, and then press . * To delete all the specified color from the palette, press . f Press to return to the original - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 135
EDITING PATTERNS a Insert the USB media containing the custom thread table data into the USB port. d The recalled custom thread displayed on the screen. table is E Choosing a Color from the Custom Thread Table 2 You can select a color from the up to 300 thread colors you have set in the - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 136
EDITING PATTERNS c Press . a Designing Repeated Patterns ■ Sewing Repeated Patterns Using the border function, you can create stitches using repeated patterns. You can also adjust the spacing of the patterns within a repeated pattern stitch. a Select a pattern, and then press . b Press . a - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 137
EDITING PATTERNS e Adjust the spacing of the repeated pattern. * To widen spacing, press . E * To tighten spacing, press . 2 Embroidery Edit b d e a Vertical direction b Horizontal direction c Repeating and deleting vertical keys d Repeating and deleting horizontal keys e Spacing keys → - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 138
EDITING PATTERNS ■ Repeating One Element of a Repeated Pattern c Press . By using the Cut function, you can select one element of a repeated pattern and repeat only that single element. This function allows you to design complex repeated patterns. a Choose the direction pattern will be cut. - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 139
color can be continuously sewn. This allows you to continue sewing without repeatedly changing the upper thread or changing the sewing order manually. Memo • In combined stitch patterns that contain two or more border patterns or other patterns combined with border patterns, the sewing order - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 140
EDITING PATTERNS a Press . b Press . d Press . c Press sewn. to select the thread mark to be Embroidering the Pattern Repeatedly After creating the repeated pattern, rehoop the embroidery frame and keep sewing for the next pattern. Memo • The optional border frame allows you to easily - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 141
EDITING PATTERNS a Create the repeated pattern with the thread mark at the center of the end of the pattern. e Rehoop the fabric in the embroidery frame. * Refer to "Assigning Thread Marks" on page E-75. Note E • Adjust the position of the fabric so that the embroidering area for the next - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 142
EDITING PATTERNS g Touch to set the starting point to the center top of the pattern. Duplicating a Pattern a Press . h Touch . i Press the positioning keys to move the embroidery frame until the starting point is aligned with the thread mark on the fabric. → The duplicate is positioned - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 143
After Editing a Press . EDITING PATTERNS E 2 Embroidery Edit * To combine the pattern with other patterns, select (see page E-80). * See page E-21 for more information about sewing patterns. Memo • If you want to return to the edit screen after pressing , press . Embroidering E-79 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 144
COMBINING PATTERNS COMBINING PATTERNS Editing Combined Patterns Example: Combining alphabet characters with an embroidery pattern and editing b Select . a Press pattern. to select an embroidery c Press . E-80 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 145
d Press . COMBINING PATTERNS f Select and enter "Flower". * After selecting , press to change the character case, then enter the remaining characters. E 2 Embroidery Edit e Press to enter the alphabet characters. * Press to return to the previous screen. → The characters you enter - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 146
COMBINING PATTERNS j Press to characters. change the color of the * See page E-67 for more information about changing the color. Memo • Use to select patterns that are overlapping and cannot be selected by clicking them or by touching the screen. k When all editing is finished, press . - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 147
Sewing Combined Patterns Combined patterns will be embroidered in the order they were entered. In this example, the embroidery order will be as follows: b Embroider → COMBINING PATTERNS . E 2 Embroidery Edit Note • Follow the directions in "Sewing Embroidery Patterns" on page E-22. a Embroider - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 148
VARIOUS EMBROIDERING FUNCTIONS VARIOUS EMBROIDERING FUNCTIONS Uninterrupted Embroidering (Monochrome - Using a Single Color) A selected pattern can be stitched out in one color instead of multicolor. The machine will hesitate but not stop between color steps, and then continue till the pattern is - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 149
Memo • To cancel the setting, press . → Basting is added to the beginning of the sewing order. f Press the "Start/Stop" embroidering. button to begin USING THE MEMORY FUNCTION g When embroidering basting stitching. is finished, remove the E 2 Embroidery Edit USING THE MEMORY - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 150
USING THE MEMORY FUNCTION E-86 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 151
section provides important information for operating this machine. Please read this section to find troubleshooting tips and pointers as well as how to keep your machine in the best working countries or regions. Chapter1 How to Create Bobbin Work A-2 Chapter2 Maintenance and Troubleshooting A-14 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 152
Embroidering 10 ADJUSTING THE THREAD TENSION 12 ■ Adjusting the upper thread tension 12 ■ Adjusting the tension of the bobbin thread 12 TROUBLESHOOTING 13 ■ The thread was accidentally cut automatically and the bobbin thread is caught inside the machine 13 ■ Correcting bobbin work tension - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 153
How to Create Bobbin Work Refer to the "Quick Reference Guide" about the bobbin work patterns. PREPARING FOR BOBBIN WORK Required that bobbin case tension not be applied. Refer to page A-6 for more detailed instructions. Note • Do not use thread heavier than No.5 hand embroidery thread. • Some - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 154
PREPARING FOR BOBBIN WORK ■ Upper thread Embroidery thread (polyester thread) or monofilament (transparent nylon) thread. If you do not wish for the upper thread to be visible, we recommend using transparent nylon monofilament thread or polyester light weight thread (50wt. or above) that is the same - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 155
PREPARING FOR BOBBIN WORK f Wipe the bobbin case free cloth to clean it. (gray) with a soft lint h Wind a decorative thread around the bobbin by hand. After winding the bobbin g Insert the bobbin case so that the S mark on the bobbin case aligns with the ● mark on the machine. so it is - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 156
in the thread catching on the tension spring of the bobbin case, the thread completely becoming tangled or damage to the machine. • Do not guide the bobbin thread through the groove in the needle plate cover, otherwise the lower threading cannot be done correctly. k Pull out about 8 bobbin thread - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 157
m Gently pull the upper thread to bring the bobbin thread up through the needle plate. PREPARING FOR BOBBIN WORK p Install the needle cover with tabs. plate cover and bobbin For details on installing the needle plate cover, refer to A "Cleaning the Race" on page A-15. 1 How to Create - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 158
with an amount of thread for pattern. adequate Note • For an estimated length of bobbin thread required for each pattern, refer to the "Quick Reference Guide" included with the machine. Be sure to use a bobbin wound with enough thread. If the bobbin runs out of thread while sewing, the embroidery - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 159
CREATING BOBBIN WORK How to Create Bobbin Work CAUTION • When sewing bobbin work, be sure to select an embroidery pattern for bobbin work. If any other type of pattern is selected, the machine may be damaged. Note • Bobbin work embroidery sewing speed defaults to 100 spm when a bobbin work - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 160
CREATING BOBBIN WORK Start Embroidering a Hoop the fabric so the right side of the fabric is facing down with the stabilizer lying on the top. Use an embroidery frame that fits the size of the pattern and then attach the frame to the machine. These patterns are embroidered from the wrong - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 161
k Stop the machine, and thread and the bobbin then tie the upper thread together to secure the threads. CREATING BOBBIN WORK o Remove the fabric from the embroidery frame, and check the finished embroidery. A 1 How to Create Bobbin Work l Start sewing again to finish the pattern. m Raise - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 162
ADJUSTING THE THREAD TENSION ADJUSTING THE THREAD TENSION After embroidering trial patterns and checking the results, adjust the thread tensions if necessary. After adjusting the tensions, be sure to embroider trial patterns again in order to check the results. ■ Adjusting the upper thread - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 163
How to Create Bobbin Work TROUBLESHOOTING A Several solutions for minor problems are described below. If the problem persists, contact your dealer or nearest authorized Brother dealer. 1 ■ The thread was accidentally cut ■ Correcting bobbin work tension automatically and the bobbin - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 164
Maintenance Message 17 ADJUSTING THE SCREEN 18 Adjusting the Brightness of the Screen Display 18 Touch Panel is Malfunctioning 18 TROUBLESHOOTING 19 ERROR MESSAGES 22 SPECIFICATIONS 25 UPGRADING YOUR MACHINE'S SOFTWARE........ 26 Upgrade Procedure Using USB Media 26 Upgrade Procedure Using - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 165
shock or injury may result. Maintenance and Troubleshooting Restrictions on oiling Cleaning the Machine Casing In , making periodic oiling unnecessary. If problems occur, such as difficulty turning the authorized dealer or the nearest authorized service center. Precautions on storing the machine - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 166
CARE AND MAINTENANCE g Use the cleaning brush to remove any lint and or a vacuum cleaner dust from the race and bobbin thread sensor and the surrounding area. a Cleaning brush b Race c Bobbin thread sensor Note • Do not apply oil to the bobbin case. • If lint or dust collects on the bobbin - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 167
used. Clean the cutter when the thread is not easily cut. Maintenance and Troubleshooting a Follow steps a through e in "Cleaning the Race" on page A- to take your machine to an authorized dealer or nearest authorized service center for a regular maintenance check. Although this message will - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 168
ADJUSTING THE SCREEN ADJUSTING THE SCREEN Adjusting the Brightness of the Screen Display If the screen does not look very clear under certain situation, you can adjust the brightness of the screen display. a Press . → The settings screen appears. b Display page 3 of the settings screen. c - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 169
. If you need additional help, the Brother Solutions Center offers the latest FAQs and troubleshooting tips. Visit us at " http://solutions.brother.com ". If the problem persists, contact your dealer or the nearest authorized service center. Problem Cause Solution The thread is tangled on - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 170
TROUBLESHOOTING Problem Cause Solution Bobbin thread does The thread is not passed through the bobbin not wind neatly on the winding thread guide correctly. bobbin. Bobbin spins slowly. Correctly pass the thread through the bobbin winding thread guide. Press [+] in the bobbin winding window - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 171
TROUBLESHOOTING Problem . opposite direction. Contact your dealer or the nearest authorized service center. The LCD screen is fogged up. Condensation has having a very uneven surface, the position is not correctly aligned. Manually adjust the position according to the thickness of the fabric. The - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 172
ERROR MESSAGES Problem Cause Specifying with sensor pen cannot be done accurately : Turn the main power to OFF and unplug the machine. If you restart the machine, follow the instructions for operating the machine correctly. ERROR MESSAGES If the machine is not properly set and the "Start/Stop - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 173
. Thread the upper thread from the beginning. This message appears when the machine is in the shutoff support mode. Turn off the machine once to start the machine again. (see page B-25) This message of compatible file formats. (see page E-44) Maintenance and Troubleshooting A 2 Appendix A-23 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 174
by USB This message is displayed when you try to use incompatible USB media. For a list of compatible USB media, visit " http://solutions.brother.com ". This message is displayed while the USB media is transmitting. Turn off the power and replace the needle plate. USB media error This - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 175
(approx. 8.5 lb) Approx. 6.0 kg (approx. 13.2 lb) Approx. 27.0 kg (approx. 59.5 lb) * Please be aware that some specifications may change without notice. Maintenance and Troubleshooting A 2 Appendix A-25 - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 176
USB media or a computer to upgrade software for your machine. When an upgrade program is available on " http://solutions.brother.com ", please download the files following the instructions on the website and steps below. Note • When using USB media to upgrade the software, check that no data other - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 177
the main power to ON. 2 → The following screen will appear on the LCD. b Press . e When the message disappears, press . Maintenance and Troubleshooting c Plug the USB cable connector into the corresponding USB ports for the computer and for the machine. → "Removable Disk" will appear in - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 178
INDEX INDEX A Accessories options B-13 Adjusting the LED pointer B-44 Air vent B-8 Aligning the position E-36 Alphabet characters embroidery E-5 embroidery edit E-59 Appliqué embroidery patterns E-23 using an embroidery frame pattern E-51 , Array key E-60 E-64 , Arrow keys E-36 E-81 , - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 179
settings B-22 thread tension E-30 thread trimming E-32 Shutoff support mode B-25 , Size key E-37 E-63 Speaker guide B-8 B-32, B-35 Thread guide plate B-8, B-35, B-38 Thread marks E-75 Thread palette key E-66, E-67, E-71 Top cover B-8 , Touch pen E-67 A-18 Trial key E-19 Troubleshooting - Brother International DreamMaker„ XE VE2200 | Users Manual - English - Page 180
Please visit us at http://solutions.brother.com where you can get product support and answers to frequently asked questions (FAQs). English 882-D80/D82 Printed in Taiwan XF3635-001
Operation Manual
Embroidery Machine
Product Code: 882-D80/D82
Be sure to read this document before using the machine.
We recommend that you keep this document nearby for future reference.