Brother International HL-1050 Users Manual - English

Brother International HL-1050 Manual

Get Brother International HL-1050 PDF manuals and user guides View all Brother International HL-1050 manuals
Add to My Manuals
Save this manual to your list of manuals

Brother International HL-1050 manual content summary:

  • Brother International HL-1050 | Users Manual - English - Page 1
    Please read this manual thoroughly before using the printer. HL-800/1000 Series User's Guide Keep this manual in a convenient place for quick and easy reference at all times.
  • Brother International HL-1050 | Users Manual - English - Page 2
    LAMPS AND SWITCH ...3-1 Ready (Paper) Lamp ...3-1 Data (Toner) Lamp ...3-2 Drum Lamp...3- 2 Alarm Lamp...3- 2 Switch ...3-3 Other Control Features 3-3 Sleep Mode ...3-3 Test Print Mode ...3-4 CHAPTER 4 OPTIONS 4-1 SERIAL INTERFACE BOARD RS-100M (HL-1040/1050 Only 4-1 Selecting the RS-422A (Apple
  • Brother International HL-1050 | Users Manual - English - Page 3
    THE TONER CARTRIDGE 5-1 REPLACING THE DRUM UNIT 5-7 CLEANING THE PRINTER 5-11 Cleaning the Printer Exterior 5-11 Cleaning the Printer Interior and Drum Unit 5-12 RE-PACKING THE PRINTER 5-15 CHAPTER 6 TROUBLESHOOTING 6-1 ALARM INDICATIONS AT A GLANCE 6-1 Operator Calls...6-1 Service Calls
  • Brother International HL-1050 | Users Manual - English - Page 4
    The following conventions are used in this User's Guide: Warning Indicates warnings that must be observed to prevent possible personal injury. ! Caution Indicates cautions that must be observed to use the printer properly or prevent damage to the printer. Note Indicates notes and useful tips to
  • Brother International HL-1050 | Users Manual - English - Page 5
    is recommended that you save and use the original packaging. The Printer should also be adequately insured with the carrier. Warning When shipping the Printer, the DRUM UNIT assembly including the TONER CARTRIDGE must be removed from the Printer and placed in the plastic bag. Failure to remove and
  • Brother International HL-1050 | Users Manual - English - Page 6
    In CANADA Printer Customer Support Brother International Corporation 15 Musick Irvine, CA 92718 Brother International Corporation (Canada), Ltd. - Marketing Dept. 1, rue Hôtel de Ville Dollard-des-Ormeaux, PQ, Canada H9B 3H6 BBS For downloading drivers from our Bulletin Board Service, call: In
  • Brother International HL-1050 | Users Manual - English - Page 7
    . (HL-1040/1050 only) 2. Read this On-line User's Guide to get information about the following. • Features and operating environment requirements of your printer - Chapter 1 • Paper Handling - Chapter 2 • Control Panel - Chapter 3 • Options - Chapter 4 • Maintenance - Chapter 5 • Troubleshooting
  • Brother International HL-1050 | Users Manual - English - Page 8
    YOUR PRINTER Printer Overview Paper Support Multi-Purpose Sheet Feeder Top Cover Extension Support Wire Output Tray Fig. 1-1 Front View Paper Guide Manual Feed Slot Control Panel RS-422A/RS-232C Serial Interface Port (HL-1040/1050 only) ON 12 345678 Parallel Interface Port USB Port (HL
  • Brother International HL-1050 | Users Manual - English - Page 9
    ) 10 MB of space available on your hard disk for the printer driver and all fonts Microsoft Windows 95/98, 3.1/3.11 or Windows NT 4.0 ! Caution The HL-820/1020 printer has been designed specifically for Windows 95/98, 3.1/3.11 and Windows NT 4.0. It cannot work in a DOS environment such as MS-DOS
  • Brother International HL-1050 | Users Manual - English - Page 10
    Printer Emulation Support These printers support the following popular printer emulation modes. The HL-1040 supports HP LaserJet IIP, Epson FX-850, and IBM Proprinter XL. The HL-1050 supports HP LaserJet 6P/6L, Epson FX-850 and IBM Proprinter XL. When you use DOS application software or Windows
  • Brother International HL-1050 | Users Manual - English - Page 11
    : when your printer is out of paper, the dialog box will display "Paper Empty" and instructions for the proper corrective action. (For HL-1050 Only) USB For HL-1040/1050 Only) Optional Apple Macintosh® Interface An optional Apple Macintosh serial interface is available, which allows your printer to
  • Brother International HL-1050 | Users Manual - English - Page 12
    of time, sleep mode automatically reduces power consumption. The printer consumes less than 13 W when in sleep mode. Low Running Cost Since the toner cartridge is separate from the drum unit, you need to replace only the toner cartridge after approximately 2,400 pages, which is cost effective and
  • Brother International HL-1050 | Users Manual - English - Page 13
    the ventilation hole of the printer is blocked. Do not place the printer where it is exposed to direct sunlight. Use a blind or a heavy curtain to protect the printer from direct sunlight when the printer is unavoidably set up near a window. Do not place the printer near devices that contain magnets
  • Brother International HL-1050 | Users Manual - English - Page 14
    to strong physical shocks or vibrations. Do not expose the printer to open flames or salty or corrosive gasses. Do not place objects on top of the printer. Do not place the printer near an air conditioner. Keep the printer horizontal when carrying. Do not cover the slots in the top cover. 1-8
  • Brother International HL-1050 | Users Manual - English - Page 15
    CHAPTER 2 PAPER HANDLING CHAPTER 2 PAPER HANDLING PAPER SPECIFICATIONS The printer can handle paper that has the following specifications. Paper Type (in USA) / Xerox 80 Premier Paper (in Europe) or equivalent Label: Avery laser label or equivalent Transparency: 3M CG3300 or equivalent 2-1
  • Brother International HL-1050 | Users Manual - English - Page 16
    has problems feeding from the multi-purpose sheet feeder, use the manual feed slot and try again. Use neutral paper. Do not use acid paper to avoid any damage to the printer drum unit. You can use recycled paper in this printer. Make sure to select the appropriate media type in the printer driver
  • Brother International HL-1050 | Users Manual - English - Page 17
    straighten the paper as much as possible. Feeding curled paper can cause paper jams and misfeeds. Fig. 2-1 Fan the Paper and Straighten the Paper The printer can handle 9" width paper. However, you may get stains on the paper outside 8.5" width or on the back of the paper. If different types of
  • Brother International HL-1050 | Users Manual - English - Page 18
    USER'S GUIDE Envelopes The following types of envelopes are not recommended for use. Damaged, of baggy construction Envelopes not sharply creased Embossed envelopes Envelopes already printed by a laser printer Envelopes pre-printed on the inside Envelopes that cannot be arranged uniformly when placed
  • Brother International HL-1050 | Users Manual - English - Page 19
    size, and orientation in your application software. If your application software does not support your custom paper size, select the next paper size up that is closest . 3. Send your file or document to the printer. When the printer receives data, it begins the print process by loading paper from the
  • Brother International HL-1050 | Users Manual - English - Page 20
    USER'S GUIDE Loading Paper into the Feeder To load paper into the feeder, follow these steps. 1. Open the multi-purpose sheet feeder by gently pulling the lid
  • Brother International HL-1050 | Users Manual - English - Page 21
    Close the multi-purpose sheet feeder. ( ) Fig. 2-5 Moving the Paper Guide and Closing the Feeder Note If the multi-purpose sheet feeder runs out of to cancel the alarm and continue printing. If paper jams in the printer, the Alarm and Paper lamps also blink. If the error is a paper jam, clear it
  • Brother International HL-1050 | Users Manual - English - Page 22
    USER'S GUIDE Two Side Printing (Manual Duplexing) The supplied printer driver for Windows 95/98 or Windows 3.1 enables manual duplex printing. For more information about settings, see the help text in the printer driver. The printer prints all the even numbered pages on one side of the paper first,
  • Brother International HL-1050 | Users Manual - English - Page 23
    to the paper width you are using. ( ) Fig. 2-7 Moving the Paper Guide When you load more than one sheet of paper manually: Open the Setup dialog box of the supplied Windows printer driver and choose Manual Feed in the Paper Source section. Follow the above instructions to load the first page. The
  • Brother International HL-1050 | Users Manual - English - Page 24
    USER'S GUIDE Note Insert paper firmly into the manual feed slot. Be sure to load sheet by sheet when using the manual feed slot. 2-10
  • Brother International HL-1050 | Users Manual - English - Page 25
    CHAPTER 2 PAPER HANDLING OUTPUT TRAY AND PAPER SUPPORT WIRE The printer ejects paper with printed surfaces face down into the output tray at the front of the printer. When the output tray is closed, the ejected paper comes out sheet by sheet through the slit at the front. When you open the tray,
  • Brother International HL-1050 | Users Manual - English - Page 26
    LAMPS AND SWITCH This section refers to the following lamps and switch on the printer control panel. Drum Alarm PaRpeeardy ToDnaetra Fig. 3-1 Lamps and Switch on Control Panel Note When the power switch is off or the printer is in sleep mode, all lamps including the Ready lamp are off. Ready
  • Brother International HL-1050 | Users Manual - English - Page 27
    REPLACING THE TONER CARTRIDGE" in Chapter 5 and "Operator Calls" in Chapter 6. Drum Lamp The Drum lamp indicates the drum unit is nearly at the end of its life. Lamp Off Printer status The drum unit can be used. On The drum unit is nearly at the end of its life. Installing a new drum unit turns
  • Brother International HL-1050 | Users Manual - English - Page 28
    Ready lamp blinks to indicate that the printer is warming up. You can change the time out for the sleep mode with the supplied printer driver (all models) or Remote Printer Console program (HL1040/1050 only). Refer to the Help section in the printer driver or RPC program for more information about
  • Brother International HL-1050 | Users Manual - English - Page 29
    restored to the factory setting and permanent fonts and macros are cleared. The printer returns to the ready status after printing. (HL-1040/1050 only) The printer can print data as hexadecimal values, so that you can check data errors and problems. To exit from this mode, you have to turn off the
  • Brother International HL-1050 | Users Manual - English - Page 30
    OPTIONS SERIAL INTERFACE BOARD RS-100M (For HL-1040/1050 Only) To connect the printer to a DOS computer with a serial installed onto the main controller board inside the printer. For the details about installation, see the instruction guide which was provided with the serial interface board.
  • Brother International HL-1050 | Users Manual - English - Page 31
    USER'S GUIDE If necessary, select the interface type as follows: 1. Make sure that the printer is in the off-line state. 2. in several different places, within your DOS application, within the Windows Printer Icon (for Windows application software only), or within your AUTOEXEC.BAT file using MODE
  • Brother International HL-1050 | Users Manual - English - Page 32
    CHAPTER 4 OPTIONS If necessary, set the serial interface parameters as follow: 1. Make sure that the printer is in the off-line state. 2. Set the serial interface parameters by moving up (on) or down (off) the selectors of the dual in-line
  • Brother International HL-1050 | Users Manual - English - Page 33
    USER'S GUIDE Table 3: Parity Settings Selector 5 On On Off Selector 6 On Off - Parity Odd Even None Note The factory settings are indicated in bold. If the robust Xon setting is turned on with selector 8, the printer sends Xon signals at one second intervals to the connected computer until it
  • Brother International HL-1050 | Users Manual - English - Page 34
    4 OPTIONS You can connect a parallel and a serial interface cable at the same time. The auto interface selection function allows you to share the printer with two computers. To do this, connect the parallel interface cable and then connect the serial interface cable as follows: 1. Make sure that the
  • Brother International HL-1050 | Users Manual - English - Page 35
    USER'S GUIDE ADDITIONAL MEMORY (HL-1050 Only) The HL-820/1020/1040 printers have 2 Mbyte of standard memory and additional memory cannot be fitted. The HL-1050 printer has 4 Mbyte of standard memory and a slot for optional additional memory. The memory can be expanded up to 36 Mbytes total by
  • Brother International HL-1050 | Users Manual - English - Page 36
    CHAPTER 4 OPTIONS Note The HL-1050 can also support DIB graphics with a resolution of 1200 x 600 dpi under Windows 95/98/3.1 with the supplied printer driver. We recommend to expand the printer memory to avoid any memory full error. Note The printer has only one slot for a SIMM upgrade. If you want
  • Brother International HL-1050 | Users Manual - English - Page 37
    USER'S GUIDE 2. Unscrew the screws securing the rear plate of the main controller board to the printer and pull out the main controller or frequently touch the surface of the antistatic package or bare metal on the printer. 4. Install the SIMM into the slot and push it gently towares the vertical until
  • Brother International HL-1050 | Users Manual - English - Page 38
    CHAPTER 4 OPTIONS 5. Install the main controller board into the printer by sliding it into the guide rails. 6. Secure the main controller board with the four screws. 7. Reconnect the interface cable (printer cable) from your computer. Plug the power cord into the AC outlet and turn on the power
  • Brother International HL-1050 | Users Manual - English - Page 39
    seal up the toner cartridge tightly so that toner powder does not spill out of the cartridge. Do not discard used toner cartridges together with domestic rubbish. It is recommended that you clean the printer when you replace the toner cartridge. See "CLEANING THE PRINTER" in this chapter. Drum Alarm
  • Brother International HL-1050 | Users Manual - English - Page 40
    USER'S GUIDE ! Caution Keep the drum unit level after removing the toner cartridge, to avoid possible toner spill or scatter. Follow these steps to replace the toner cartridge: 1. Open the top cover towards you. Remove the drum unit by holding each side of the drum and gently lifting the drum
  • Brother International HL-1050 | Users Manual - English - Page 41
    you open the top cover of the printer, never touch the shaded parts shown in the following illustration. High Temperature Fig. 5-3 Inside the Printer 2. Gently turn the lever on the toner cartridge forward until it stops. Note The toner cartridge cannot be removed unless the shutter is completely
  • Brother International HL-1050 | Users Manual - English - Page 42
    USER'S GUIDE 3. Remove the old toner cartridge from the drum unit by pulling it out gently. Fig. 5-5 Removing the Old Toner Cartridge ! Caution Handle the toner cartridge carefully. If toner scatters on your hands or clothes, wipe or wash it off with cold water immediately. 4. Unpack the new toner
  • Brother International HL-1050 | Users Manual - English - Page 43
    drum unit. Make sure that the toner cartridge guide bar is exactly aligned with the guide slot in the drum unit and pushed fully home into the drum unit to ensure that the toner cartridge and the drum unit fit together correctly. Fig. 5-7 Installing the Toner Cartridge into the Drum Unit 6. Gently
  • Brother International HL-1050 | Users Manual - English - Page 44
    USER'S GUIDE 8. Clean the primary corona wire inside the drum unit by gently sliding the blue tab to the right and left several times. Home Position ( ) Fig. 5-9 Cleaning the Primary Corona Wire 9. Re-install the drum unit into the printer and close the top cover. Fig. 5-10 Close the top cover 5-6
  • Brother International HL-1050 | Users Manual - English - Page 45
    before the Drum lamp lights, then the drum unit should be replaced. Drum Alarm PaRpeeardy ToDnaetra Fig. 5-11 Drum Unit Nearly at the End of its Life ! Caution When removing the drum unit, handle it carefully as it may contain toner. You should clean the printer when you replace the drum unit. See
  • Brother International HL-1050 | Users Manual - English - Page 46
    are extremely hot. When you open the top cover of the printer, never touch the shaded parts shown in the following illustration. High Temperature Fig. 5-13 Inside the Printer 2. Remove the toner cartridge from the drum unit and keep it in a safe place. For more information, see "REPLACING THE
  • Brother International HL-1050 | Users Manual - English - Page 47
    Sheet Only unpack a drum unit immediately before installing it into the printer. If an unpacked drum unit is subjected to excessive direct sunlight or room light, the unit may be damaged. Handle the toner cartridge and the drum unit carefully as it contains toner. If toner scatters and your hands
  • Brother International HL-1050 | Users Manual - English - Page 48
    USER'S GUIDE 4. Install the toner cartridge into the new drum unit. For more information, see "REPLACING THE TONER CARTRIDGE" in this chapter. 5. Install the new drum unit into the printer. Fig. 5-17 Installing the Drum Unit 6. Close the top cover. 7. The printer automatically ejects the starter
  • Brother International HL-1050 | Users Manual - English - Page 49
    exterior and interior periodically. If printed pages get stained with toner, clean the printer interior and drum unit. Cleaning the Printer Exterior Clean the printer exterior as follows: 1. Turn off the power switch and unplug the power cord. Warning There are high voltage electrodes inside the
  • Brother International HL-1050 | Users Manual - English - Page 50
    USER'S GUIDE Cleaning the Printer Interior and Drum Unit Clean the printer interior and the drum unit as follows: 1. Turn off the power switch and unplug the power cord. Warning There are high voltage electrodes inside the printer. Before cleaning the printer, make sure to turn off the power switch
  • Brother International HL-1050 | Users Manual - English - Page 51
    USER'S GUIDE 4. Gently wipe the scanner window with a soft dry cloth. Scanner Window Fig. 5-22 Cleaning the Scanner Window ! Caution Do not touch the scanner window with your fingers. Do not wipe the scanner window with cleaning alcohol (isopropyl). 5. Turn the drum unit upside down carefully. !
  • Brother International HL-1050 | Users Manual - English - Page 52
    USER'S GUIDE 6. Clean the primary corona wire inside the drum unit by gently sliding the tab to the right and left several times. Home Position ( ) Fig. 5-23 Cleaning the Primary Corona Wire 7. Return the tab to the home position ( mark position) before reinstalling the drum unit. ! Caution Be sure
  • Brother International HL-1050 | Users Manual - English - Page 53
    AC outlet. Remove the AC cord and the extention wire of the paper tray from the printer. 2. Open the top cover. 3. Remove the drum unit assembly, referring to the previous section. Note Remove the drum unit assembly with the toner cartridge included. Fig. 5-24 Removing the Drum Unit Assembly 5-15
  • Brother International HL-1050 | Users Manual - English - Page 54
    material. 7. Place any documents (manual and any documentation describing the reason for repacking the printer) and the drum unit assembly in the carton box as shown below. 8. Close the carton box and tape it. Manuals Drum Unit Including Toner Cartridge Printer Carton Fig. 5-26 Repacking the
  • Brother International HL-1050 | Users Manual - English - Page 55
    and press the panel switch. Reinstall the paper and press the panel switch. Indicates that the printer has approximately 100 pages of printing left before the toner cartridge is empty. Prepare a new toner cartridge. Toner Empty Replace the toner cartridge with a new one referring to Chapter 5. 6-1
  • Brother International HL-1050 | Users Manual - English - Page 56
    USER'S GUIDE For errors shown below, the printer indicates an operator call by blinking the Alarm lamp. If you use the printer with the supplied Windows driver, the status monitor will appear to indicate the error on your computer screen. The HL-1040/1050 printer also prints some error messages on
  • Brother International HL-1050 | Users Manual - English - Page 57
    CHAPTER 6 TROUBLESHOOTING Error Action Serial Interface Overrun Press the panel switch to resume printing. Error The interface hardware may be damaged. Consult your (For HL-1040/1050 Only) dealer. Serial Interface Input Press the panel switch to resume printing. Buffer Overflow Check the
  • Brother International HL-1050 | Users Manual - English - Page 58
    USER'S GUIDE Service Calls If an unrecoverable error occurs, the printer indicates the need for a service call by lighting all the lamps and then the following combination of lamps alternately: Service Call Drum Alarm Ready Data Fuser malfunction Laser BD malfunction Scanner malfunction ROM
  • Brother International HL-1050 | Users Manual - English - Page 59
    PAPER JAMS CHAPTER 6 TROUBLESHOOTING Before you can clear a paper jam error, you need to find the location of the paper jams. Locate the position referring to the following figure. Paper Top Cover Multi-Purpose Sheet Feeder Drum Unit Fig. 6-1 Locating Paper Jam Position After locating the
  • Brother International HL-1050 | Users Manual - English - Page 60
    USER'S GUIDE ! Caution Do not pull jammed paper from the output tray. Be sure to open the top cover to remove the jam, or the fuser may get dirty with toner powder and may result in toner a torn piece of paper does not remain inside the printer referring to the next section. Fig. 6-4 Paper Jam in
  • Brother International HL-1050 | Users Manual - English - Page 61
    CHAPTER 6 TROUBLESHOOTING Paper Jam near the Drum Unit or at the Paper Output Tray If a paper jam has occurred near the drum unit, open the top cover and remove the drum unit. Then, pull the jammed paper upwards and out of the printer. Install the drum unit and close the top cover. Fig. 6-5 Paper
  • Brother International HL-1050 | Users Manual - English - Page 62
    the protective parts have been removed. The toner cartridge and drum unit are installed properly. The interface cable is securely connected between the printer and computer. Check to see if the Alarm lamp is blinking. If the lamp is blinking, refer to the Operator Call section of this manual. Check
  • Brother International HL-1050 | Users Manual - English - Page 63
    print resolution or reduce the complexity of your document and try again. (For HL-1050) Expand the printer memory by adding a commercially available SIMM. (For HL-1050) Change the following settings in the supplied Windows driver and try again. The best combination of the following settings may vary
  • Brother International HL-1050 | Users Manual - English - Page 64
    USER'S GUIDE Setting Up the Printer for DOS (For HL-1040/1050 Only) Question I cannot print from my application software. The printer prints, but it prints incorrect information. Sometimes it prints a couple of characters and then ejects the page, etc. The printer does not print when I press the
  • Brother International HL-1050 | Users Manual - English - Page 65
    TROUBLESHOOTING Setting Up the Printer for Apple Macintosh Computers When the Optional RS-100M Serial Interface Is Installed into Your Printer (For HL-1040/1050 Only) Question I cannot print from my application software. Recommendation Make sure that the supplied Macintosh printer driver manual
  • Brother International HL-1050 | Users Manual - English - Page 66
    USER'S GUIDE Printing Question The printer prints unexpectedly or it prints garbage. The printer cannot print full pages of a document. An error message "PRINT OVERRUN" occurs. The printer prints the first couple of pages correctly, then some pages have text missing. (For HL-1040/1050 Only)
  • Brother International HL-1050 | Users Manual - English - Page 67
    TROUBLESHOOTING Question The printer cannot print full pages of a document. A "MEMORY FULL" error message occurs. (For HL-1040/1050 Only) Recommendation (For HL-1050) Change the following settings in the supplied Windows driver your application software. Most laser printers have a restricted area
  • Brother International HL-1050 | Users Manual - English - Page 68
    the primary corona wire of the toner cartridge. See "Cleaning the Printer Interior and Drum Unit" in Chapter 5. Make sure that the tab of the corona wire is at the home position. If the same print problem occurs and the Drum lamp is still on after cleaning, replace the drum unit with a new one. Fig
  • Brother International HL-1050 | Users Manual - English - Page 69
    after the first 10-20 pages with the new toner cartridge. If you still have the same problem and the Drum lamp is on, replace the drum unit with a new one. Wipe the electric terminals referring to "Cleaning the Printer Interior and Drum Unit" in Chapter 5. Never use heat-sensitive paper as it
  • Brother International HL-1050 | Users Manual - English - Page 70
    drum unit with the toner cartridge installed. Try shaking them from side to side. You may clear the problem by wiping the scanner windows with a soft cloth. (See "Cleaning the Printer Interior and Drum Unit.") If the same problem occurs after cleaning and Drum lamp is still on, replace the drum unit
  • Brother International HL-1050 | Users Manual - English - Page 71
    PRINTER SPECIFICATIONS Printing Print Method Laser Resolution Electrophotography by semiconductor laser beam scanning Wavelength: 780 nm Output: 5 mW max HL-820/1020: 600 dots/inch (under Brother Printing Solution for Windows) HL-1040: 600 dots/inch (under Brother Printing Solution for Windows
  • Brother International HL-1050 | Users Manual - English - Page 72
    FX-850, or IBM Proprinter XL Printer Driver Windows 3.1/3.11, Windows 95/98 and Windows NT 4.0 driver, supporting Brother Native Compression mode and bidirectional capability Optional Macintosh driver available for System 6.0.7 or higher (For HL-1040/1050 Only) Interface Bi-directional parallel
  • Brother International HL-1050 | Users Manual - English - Page 73
    CHAPTER 7 APPENDIX Memory Diagnostics HL-820/1020/1040 : 2 MB HL-1050: 4 MB Expandable up to 36 MB by installing an industry standard SIMM Self- x 245 x 365 mm (14.4 x 9.8 x 13.9 inches) (when the output tray is closed.) Weight Approx. 7.2 kg (14.3 lb.) including the drum unit A-3
  • Brother International HL-1050 | Users Manual - English - Page 74
    USER'S GUIDE PARALLEL INTERFACE SPECIFICATIONS Note To ensure best quality performance use an IEEE 1284 compliant parallel cable between the printer and your computer. Only IEEE 1284 cables support all of the advanced printing capabilities, like bi-directional communication. These cables will be
  • Brother International HL-1050 | Users Manual - English - Page 75
    CHAPTER 7 APPENDIX Note To use bi-directional communication, an interface cable which has the pin connections above must be used. Pin 1 18 2 19 3 4 20 5 6 21 7 8 22 9 10 24 11 23 12 13 14 25 16 15 17 Shield Pin 1 19 2 20 3 21 4 22 5 23 6 24 7 25 8 26 9 27 10 28 11 29 12 17 13 15 14 30 31 33 32 34
  • Brother International HL-1050 | Users Manual - English - Page 76
    USER'S GUIDE UNIVERSAL SERIAL BUS (USB) INTERFACE (HL-1050 only) Interface Connector 2 1 4 Pin Assignment Pin No. 1 2 3 4 Signal Vcc (+5V) - Data + Data Ground 3 Serial Data Serial Data + A-6
  • Brother International HL-1050 | Users Manual - English - Page 77
    CHAPTER 7 APPENDIX RESIDENT FONTS The following bitmapped fonts are resident in this printer. Note HL-820/1020 printer does not have resident fonts inside the printer. HL-1040 : Bitmapped Fonts Brougham 10 (12 point) upright/normal upright/bold italic/normal italic/bold Brougham 12 (10 point
  • Brother International HL-1050 | Users Manual - English - Page 78
    USER'S GUIDE Intellifont Compatible Fonts Alaska (Extrabold) Antique Oakland (Oblique, Bold) Brougham (Oblique, , BoldItalic) PC Brussels Light (Italic, Demi, DemiItalic) Utah (Oblique, Bold, BoldOblique) Utah Condensed (Oblique, Bold, BoldOblique) Microsoft Windows 3.1 TrueType Compatible Fonts
  • Brother International HL-1050 | Users Manual - English - Page 79
    used. OCR-A OCR-B HP LaserJet IIP Mode ( HL-1040 ) ISO14 JIS ASCII ISO57 Chinese ISO11 Swedish HP Spanish (17U) PC-775 (26U) PC-1004 (9J) PC-8 Turkish (9T) Windows Latin1 (19U) Windows Latin2 (9E) Windows Latin5 (5T) Windows Baltic (19L) Legal (1U) Ventura Math (6M) Ventura Intl (13J) Ventura
  • Brother International HL-1050 | Users Manual - English - Page 80
    USER'S GUIDE EPSON Mode ( HL-1040/1050 ) US ASCII PC-8 PC-8 D/N PC-850 PC-852 PC-860 PC-863 PC-865 PC-8 Turkish German UK ASCII I French I Danish I Italy Spanish Swedish IBM Mode ( HL-1040/1050 ) PC-8 PC-8 D/N PC form" option in the Direct Access Menu of the Remote Printer Console Program. A-10
  • Brother International HL-1050 | Users Manual - English - Page 81
    HP LaserJet IIP / HP LaserJet 6P CHAPTER 7 APPENDIX The following table shows characters available only in the corresponding character set. The numbers at the top of the table are code values with which characters are to be replaced in the Roman 8 character set. For other characters, see the
  • Brother International HL-1050 | Users Manual - English - Page 82
    USER'S GUIDE HP LaserJet IIP/6P, EPSON FX-850, IBM Propritner XL EPSON FX-850 A-12
  • Brother International HL-1050 | Users Manual - English - Page 83
    CHAPTER 7 APPENDIX The following table shows characters available only in the corresponding character set. The numbers at the top of the table are code values with which characters are to be replaced in the US ASCII character set. For other characters, see the character set of US ASCII. A-13
  • Brother International HL-1050 | Users Manual - English - Page 84
    . All other brand and product names mentioned in this User's Guide are registered trademarks of their respective companies. Compilation and Publication Notice Under the supervision of Brother Industries Ltd., this manual has been compiled and published, covering the latest product's descriptions
  • Brother International HL-1050 | Users Manual - English - Page 85
    Brother Laser Printer HL-820, HL-1020, HL-1040, HL-1040DX, HL-1050, HL-1050DX Model Numbers : HL-8L, HL-8h Product Options : ALL complies with Part used in accordance with the instructions, may cause harmful interference turning the equipment off and on, the user is encouraged to try to correct the
  • Brother International HL-1050 | Users Manual - English - Page 86
    USER'S GUIDE Radio Interference (220-240 V Model Only) This printer complies with EN55022(CISPR Publication 22)/ the printer indicates compliance with the FDA regulations and must be attached to laser products marketed in the United States. MANUFACTURED: Brother Corporation (Asia) Ltd. Brother Buji
  • Brother International HL-1050 | Users Manual - English - Page 87
    Brother International Europe Ltd. European Technical Services Division IEC 825 Specification (For 220-240 V Model Only) This printer is a Class 1 laser product manual may result in hazardous radiation exposure. The following caution label is attached near the scanner unit. CAUTION INVISIBLE LASER
  • Brother International HL-1050 | Users Manual - English - Page 88
    USER'S GUIDE For Finland and Sweden LUOKAN 1 LASERLAITE KLASS 1 LASER APPARAT Varoitus! Laitteen käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasers . Disconnect device This printer must be installed near
  • Brother International HL-1050 | Users Manual - English - Page 89
    in accordance with the following code: Green and yellow: Blue: Brown: Ground Neutral Live The colours of the wiring in the power lead of this printer may not correspond with the markings which identify the terminals in your plug. If you need to fit a different plug, proceed as follows. Remove
  • Brother International HL-1050 | Users Manual - English - Page 90
    drum unit 5-7 life 5-7, A-2 duplex printing 2-8 E economy mode 1-6 emulation 1-4, A-2 envelope 2-1, 2-4 error message 6-2 recoverable 6-1 unrecoverable 6-4 extension wire 1-2 F Factory Reset 2-1 type 2-1 paper guide 1-2 Paper lamp 3-1, 6-1 paper support 1-2 parallel interface pin
  • Brother International HL-1050 | Users Manual - English - Page 91
    area 2-4 printer driver A-2 printer status monitor 1-5 R Ready lamp 3-1 Remote Printer Console 1-4 resident font A-7 resolution 1-3, A-1 RPC 1-4 RS-232C 4-2 RS-422A 4-2 S scanner window 5-13 serial interface 4-1 cable 4-4 parameter 4-3 RS-422A/RS-232C port 1-2 service call 6-4 sleep
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
Please read this manual thoroughly before using the printer.
±²³´µ¶²·¸¹º¶²·»²¼½´¶²
±²³´µ¶²·¸¹º¶²·»²¼½´¶²
±²³´µ¶²·¸¹º¶²·»²¼½´¶²
±²³´µ¶²·¸¹º¶²·»²¼½´¶²
HL-800/1000 Series
User’s Guide
Keep this manual in a convenient place for quick and easy reference at all times.