Brother International Innov-ís 950D Users Manual - English
Brother International Innov-ís 950D Manual
View all Brother International Innov-ís 950D manuals
Add to My Manuals
Save this manual to your list of manuals |
Brother International Innov-ís 950D manual content summary:
- Brother International Innov-ís 950D | Users Manual - English - Page 1
Computerized Embroidery and Sewing Machine Operation Manual Product Code 885-V95/V97 GETTING READY SEWING BASICS UTILITY STITCHES EMBROIDERY APPENDIX Please visit us at http://solutions.brother.com where you can get product support and answers to frequently asked questions (FAQs). - Brother International Innov-ís 950D | Users Manual - English - Page 2
- Brother International Innov-ís 950D | Users Manual - English - Page 3
Thank you for purchasing this embroidery and sewing machine. Before using this machine, carefully read the "IMPORTANT SAFETY INSTRUCTIONS", and then study this manual for the correct operation of the various functions. In addition, after you have finished reading this manual, store it where it can - Brother International Innov-ís 950D | Users Manual - English - Page 4
occurs or adjustment is required, first follow the troubleshooting table in the back of the operation manual to inspect and adjust the machine yourself. If the problem persists, please consult your local authorized Brother dealer. Use this machine only for its intended use as described in the - Brother International Innov-ís 950D | Users Manual - English - Page 5
children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play - Brother International Innov-ís 950D | Users Manual - English - Page 6
4 - Brother International Innov-ís 950D | Users Manual - English - Page 7
IMPORTANT SAFETY INSTRUCTIONS 1 Machine Features ...8 Accessories ...9 Included accessories ...9 Optional accessories ...10 Names of Machine Parts and Sewing Cylindrical Pieces and Large Pieces 46 Free-arm sewing ...46 Using extension table ...46 SEWING BASICS 49 Sewing ...50 General sewing - Brother International Innov-ís 950D | Users Manual - English - Page 8
...66 Saving stitch settings ...67 Useful Sewing Tips ...68 Trial sewing ...68 Changing the sewing direction ...68 Sewing curves ...68 Sewing thick fabrics ...68 Sewing hook-and-loop fastener ...69 Sewing thin fabrics ...70 Sewing stretch fabrics ...70 Sewing an even seam allowance ...70 UTILITY - Brother International Innov-ís 950D | Users Manual - English - Page 9
the Memory Function 169 Embroidery data precautions ...169 Transferring embroidery patterns from the computer to machine 171 Saving patterns ...174 APPENDIX 175 Care and Maintenance ...176 Cleaning the machine surface ...176 Cleaning the race ...176 Troubleshooting ...178 Error messages ...183 - Brother International Innov-ís 950D | Users Manual - English - Page 10
Start/Stop button When the green light is on, the machine is ready to sew. A red or orange light indicates an error or that the machine is warming up (page 13). l Embroidery You can embroider built-in embroidery patterns, alphanumeric characters, framed decorations, and designs from optional - Brother International Innov-ís 950D | Users Manual - English - Page 11
-031 X59370-021 5 Zigzag foot "J" (on machine) XC3021-031 6 Blind stitch foot "R" 7 Button Embroidery foot "Q" Embroidery set (medium) 25 H 10 cm X W 10 cm (H 4 inches X W 4 inches) 26 Embroidery bobbin thread (white) 27 Accessory case 28 Hard case 29 Operation manual 30 Quick reference guide - Brother International Innov-ís 950D | Users Manual - English - Page 12
Embroidery bobbin thread (black) 2 Embroidery card Embroidery set (small) 3 H 2 cm u W 6 cm (H 1 inch u W 2-1/2 inches) Embroidery for embroidery 6 Walking foot 7 Open toe quilting foot 8 Side cutter "S" 9 Quilting guide Part service center or visit the website at [http://www.brother. - Brother International Innov-ís 950D | Users Manual - English - Page 13
panel (page 14) Use the keys on this panel to select stitches or embroidery patterns, or check how to use the sewing machine, etc. g Embroidery unit connector slot (page 141) Plug in the connector for the embroidery unit. h Presser foot lever (page 54) Raise and lower the presser foot lever - Brother International Innov-ís 950D | Users Manual - English - Page 14
foot holder. a Handle Carry the sewing machine by its handle when transporting the machine. b Handwheel (page 54) Turn the handwheel toward you (counterclockwise) to raise and lower the needle to sew one stitch. c Embroidery card slot (page 156) Insert the embroidery card. d USB port (for a USB - Brother International Innov-ís 950D | Users Manual - English - Page 15
buttons help you to easily perform various basic sewing machine operations. a Start/stop button Press the start/stop button to start or stop sewing. The machine sews at a slow speed at the beginning of sewing while the button is pressed. When sewing is stopped, the needle is lowered in the - Brother International Innov-ís 950D | Users Manual - English - Page 16
page when there are items that are not displayed on the LCD. e Memory key Press to save character embroidery, combined stitch patterns, My Custom Stitch patterns, etc. in the sewing machine's memory. f Utility stitch key Press this key to select a utility stitch or decorative stitch or to design - Brother International Innov-ís 950D | Users Manual - English - Page 17
preparations required before starting to sew are described in this chapter. Turning the Machine On/Off 16 LCD (Liquid Crystal Display) Operation 18 Winding/Installing the Bobbin 22 Upper Threading ...31 Replacing the Needle 39 Replacing the Presser Foot 43 Sewing Cylindrical Pieces and Large - Brother International Innov-ís 950D | Users Manual - English - Page 18
On/Off This section explains how to turn the sewing machine on and off. Power supply precautions Be sure to . ● Do not touch the plug with wet hands. Electric shock may result. ● When unplugging the machine, always turn off the main power first. Always grasp the plug to remove it from the outlet. - Brother International Innov-ís 950D | Users Manual - English - Page 19
Prepare the included power cord. When you have finished using the sewing machine, Make sure that the sewing machine is turned turn it off. In addition, before transporting the sewing machine to another location, be sure to turn it off. 1 a off (the main power switch is set to " "), and then - Brother International Innov-ís 950D | Users Manual - English - Page 20
unit is attached. The details are explained in "Selecting an embroidery pattern" (page 155). z Refer to "Error messages" (page 183) for messages displayed on the LCD. z Depending on the model of sewing machine, an animation may be displayed when the power is turned on. When an animation - Brother International Innov-ís 950D | Users Manual - English - Page 21
count and the total number of embroidery stitches. The service count is a reminder to take your machine in for regular servicing. (Contact your authorized dealer for details.) NO.: The "NO." is the number for the embroidery and sewing machine. Version: Displays the program version. Lighter - Brother International Innov-ís 950D | Users Manual - English - Page 22
settings are complete, press d (Back key). X The initial stitch screen appears again. Memo z "NO." is the individual number for the sewing machine. z "VERSION" is the program version which is installed in the sewing machine. z Settings that are changed are saved even if the power is turned off. 20 - Brother International Innov-ís 950D | Users Manual - English - Page 23
attachment / Example: Upper threading embroidery frame attachment / embroidery foot attachment / presser foot replacement on the LCD. Turn on the sewing machine. a X The LCD comes on. Press (Sewing machine help key) on b the display panel. X The sewing machine help screen appears. Press the - Brother International Innov-ís 950D | Users Manual - English - Page 24
. Use of any other bobbin may result in injuries or damage to the machine. ● The included bobbin was designed specifically for this sewing machine. If bobbins from other models are used, the machine will not operate correctly. Use only the included bobbin or bobbins of the same type (part code - Brother International Innov-ís 950D | Users Manual - English - Page 25
Turn on the sewing machine. a Place the spool of thread for the bobbin onto e the spool in the direction of the c arrow until it snaps into place. Memo z For embroidering, use the embroidery bobbin thread. Note z If the spool is not positioned so that the thread unwinds correctly, the thread - Brother International Innov-ís 950D | Users Manual - English - Page 26
long, fold it to fit the size of the spool. When the spool net is used, the upper thread tension may become tighter. Before sewing, refer to "Adjusting the thread tension" (page 62). a b a a Thread guide cover Pull the thread to the right, pass it under the i hook of the bobbin-winding thread - Brother International Innov-ís 950D | Users Manual - English - Page 27
the end of the thread through the guide k slit in the bobbin winder seat machine. When the foot controller is plugged in, remove your foot from the foot controller. X The bobbin winding will stop. CAUTION ● When the bobbin winding stops or becomes slow, stop the machine. Otherwise, the sewing machine - Brother International Innov-ís 950D | Users Manual - English - Page 28
thread is not passed under the pretension disk of the bobbinwinding thread guide correctly, the thread may become tangled under the bobbin winder seat. not move. (Sewing is impossible.) Slide the sewing speed controller back to its p original position. Memo z When the sewing machine is started or - Brother International Innov-ís 950D | Users Manual - English - Page 29
guide Slide the bobbin winder shaft to the left, and c then remove the bobbin from the shaft. Hold the thread end with your left hand, and d wind off the thread clockwise near the bobbin with your right hand as shown below. ● The included bobbin was designed specifically for this sewing machine - Brother International Innov-ís 950D | Users Manual - English - Page 30
your right hand. b a Needle position button b Presser foot lever Turn off the sewing machine. b Slide the bobbin cover latch to the right. c a b • Be incorrect. Lightly hold down the bobbin with your right g hand, and then guide the thread as shown with your left hand. a Bobbin cover b Latch X - Brother International Innov-ís 950D | Users Manual - English - Page 31
cover, and then lightly press down on the right side. a b 2 1 a Tab b Lower-left corner X The bobbin threading is finished. You can begin sewing without pulling up the bobbin thread. Next, thread the upper thread. Continue with the procedure in "Upper Threading" (page 31). Memo z When making - Brother International Innov-ís 950D | Users Manual - English - Page 32
end of the bobbin thread. Pull out about 10-15 cm (4-5 inches) of the f bobbin thread under the presser foot toward the rear of the machine. Reattach the bobbin cover. g Insert the tab in the lower-left corner of the bobbin cover, and then lightly press down on the right side - Brother International Innov-ís 950D | Users Manual - English - Page 33
instructions. If the upper threading is not correct, the thread may become tangled or the needle may bend or break. ● The needle threader can be used with a 75/11 through 100/16 home sewing machine cannot be used, refer to "Threading the needle manually (without using the needle threader)" (page 36). - Brother International Innov-ís 950D | Users Manual - English - Page 34
machine. Press (Needle position button) once or c twice to raise the needle. a CAUTION ● When threading the upper thread, carefully follow the instructions is raised. Memo z If the presser foot is not raised, the sewing machine cannot be threaded. a Mark on handwheel Pick up the spool pin and - Brother International Innov-ís 950D | Users Manual - English - Page 35
the spool pin or the needle may break. Pull the thread from the spool and pass the g thread under the hook of the thread guide. a a Thread guide a b d c a Thread guide cover b Thread guide spring c Thread d When the presser foot lever is lowered Note z When passing the thread behind the thread - Brother International Innov-ís 950D | Users Manual - English - Page 36
the thread with your right hand, as shown. a b Ta a Notch of the thread guide b Thread guide disk Cut the thread with the cutter on the left side n of the machine. Ta a Thread cutter a Needle bar thread guide Lower the presser foot lever to lower the l presser foot. a a Presser foot lever 34 - Brother International Innov-ís 950D | Users Manual - English - Page 37
. Do not touch the start/stop button, needle position button or reverse/reinforcement stitch button. If one of the buttons is accidentally pressed, the machine will begin sewing and your finger may be pricked with the needle or the needle may break. ● When pulling out the thread, do not pull it with - Brother International Innov-ís 950D | Users Manual - English - Page 38
thread" (page 32). Manually thread the left needle with the upper c thread. Pass the thread through the eye of the needle from the front. CAUTION ● The needle threader cannot be used with the twin needle. If the needle threader is used with the twin needle, the sewing machine may be damaged. 36 - Brother International Innov-ís 950D | Users Manual - English - Page 39
upper thread. Without passing the thread through the needle f bar thread guide, manually thread the right needle. Pass the thread through the eye of the needle. If the needle threader is used with the twin needle, the sewing machine may be damaged. Attach zigzag foot "J". g For details on changing - Brother International Innov-ís 950D | Users Manual - English - Page 40
X The initial screen appears again, and appears. Note z When changing the sewing direction, press (Needle position button) to raise the needle from the fabric, needle in the down position, otherwise the needle may break or the machine may be damaged. CAUTION ● When using the twin needle, be sure - Brother International Innov-ís 950D | Users Manual - English - Page 41
use bent needles. Bent needles can easily break, possibly resulting in injuries. Selecting the needle depending on the thread and fabric types The sewing machine needle that should be used depends on the fabric and thread thickness. Refer to the following table when choosing the thread and needle - Brother International Innov-ís 950D | Users Manual - English - Page 42
a 90/14 to 100/16 needle, regardless of the fabric or thread. ■ Embroidery needles Use a 75/11 home sewing machine needle. When embroidering on thick fabrics such as denim, use a 90/14 or 100/16 home sewing machine needle. CAUTION z The appropriate fabric, thread and needle combinations are shown in - Brother International Innov-ís 950D | Users Manual - English - Page 43
and a needle that has been determined to be straight according to the instructions in "Checking the needle" (page 40). Press (Needle position button) or tightening the needle clamp screw, otherwise certain parts of the sewing machine may be damaged. Place fabric or paper under the presser foot - Brother International Innov-ís 950D | Users Manual - English - Page 44
GETTING READY While holding the needle with your left hand, g use the screwdriver to tighten the needle clamp screw. Install the twin needle in the same way. CAUTION z Be sure to insert the needle until it touches the needle stopper and securely tighten the needle clamp screw with the screwdriver. - Brother International Innov-ís 950D | Users Manual - English - Page 45
Replace the presser foot as described below. Memo z For details on attaching the embroidery foot "Q", refer to "Attaching the Embroidery Foot" (page 138). z Zigzag foot "J" is already installed when the sewing machine is purchased. Press (Needle position button) once or a twice to raise the needle - Brother International Innov-ís 950D | Users Manual - English - Page 46
should be used appears in the screen. Check that the correct presser foot is attached before starting to sew. If the wrong presser foot is installed, turn off the sewing machine, attach the correct presser foot, and then select the desired stitch again. b c a Presser foot holder b Notch c Pin - Brother International Innov-ís 950D | Users Manual - English - Page 47
Remove the presser foot holder when cleaning the sewing machine or when installing a presser foot that Align the presser foot holder with the lower- 1 does not use the presser foot holder, such as the b left side of the presser bar. embroidery foot, optional free-motion open toe quilting foot - Brother International Innov-ís 950D | Users Manual - English - Page 48
bed attachment X With the flat bed attachment removed, freearm sewing is possible. Slide the part that you wish to sew onto the b arm, and then sew from the top. a a Cover of embroidery unit (extension table) CAUTION ● Do not move the sewing machine with the extension table attached. ● Do not use - Brother International Innov-ís 950D | Users Manual - English - Page 49
in their original positions. 1 Attach the extension table to the sewing c machine arm. Keep the extension table horizontal and push it in slowly until it stops. Memo ● When you do not use the extension table, use it as the cover of the embroidery unit. Memo ● If the extension table is not stable - Brother International Innov-ís 950D | Users Manual - English - Page 50
GETTING READY 48 - Brother International Innov-ís 950D | Users Manual - English - Page 51
2 SEWING BASICS The necessary preparations for sewing are described in this chapter. Sewing...50 Setting the Stitch ...61 Useful Functions...64 Useful Sewing Tips 68 - Brother International Innov-ís 950D | Users Manual - English - Page 52
on replacing the presser foot, refer to "Replacing the presser foot" (page 43). p 2 Turn on the machine. Turn on the sewing machine. For details on turning on the machine, refer to "Turning on the machine" (page 17). p 3 Select the stitch. Select the stitch appropriate for the area to be sewn - Brother International Innov-ís 950D | Users Manual - English - Page 53
for selected stitch. If the wrong presser foot is used, the needle may hit the presser foot and bend or break. Turn on the sewing machine. c • When an animation is displayed on the screen, touch the LCD with your finger. X The straight stitch (left needle position) or the straight stitch - Brother International Innov-ís 950D | Users Manual - English - Page 54
that should be used appears on the screen. Check that the correct presser foot is attached before starting to sew. If the wrong presser foot is installed, turn off the sewing machine, attach the correct presser foot, and then select the desired stitch again. Memo z For details on setting automatic - Brother International Innov-ís 950D | Users Manual - English - Page 55
select the correct character • To select a different character style, press , and then select the desired character style. • Press to view a sample of the selected pattern. Sewing 53 - Brother International Innov-ís 950D | Users Manual - English - Page 56
SEWING BASICS Positioning the fabric Be sure that the fabric pieces are sewn in the correct order and that the right and wrong sides of the fabric are aligned correctly. Turn on the machine. a While holding the end of the thread and the d fabric with your left hand, turn the handwheel toward you - Brother International Innov-ís 950D | Users Manual - English - Page 57
Once you are ready to start sewing, you can start the sewing machine. Sewing can be started and stopped using the operation button (Start/stop button) or the foot controller. For details on the foot controller, refer to next - Brother International Innov-ís 950D | Users Manual - English - Page 58
slower speed, or slide the speed controller to the right to sew at a faster speed. Turn off the sewing machine. a Note z When connecting the foot controller, be sure to turn off the sewing machine in order to prevent the machine from accidentally being started. Insert the foot controller plug into - Brother International Innov-ís 950D | Users Manual - English - Page 59
so that the needle stays up when Lower the needle into the fabric at the sewing is stopped, refer to "Changing the machine settings" (page 18). a beginning of the stitching, then lower the presser foot. 2 CAUTION z Do not allow thread or dust to accumulate in the foot controller, - Brother International Innov-ís 950D | Users Manual - English - Page 60
. At this time, if (Start/stop button) is held down, the machine sews at a slow speed. X The machine starts sewing in the normal sewing direction. After sewing to the end of the stitching, the i sewing machine stops. Release (Start/stop button) or foot controller. a 3 Press 1 Press 2 Press - Brother International Innov-ís 950D | Users Manual - English - Page 61
When you wish to finish the stitching, press a (Thread cutter button) once. 2 a b a Reverse stitching b Reinforcement stitching Memo z The sewing machine can be set to automatically sew reverse or reinforcement stitches at the beginning and end of the stitching. For details, refer to "Automatic - Brother International Innov-ís 950D | Users Manual - English - Page 62
nylon or metallic threads, or other special threads, use the thread cutter on the side of the machine to cut the threads. When you wish to finish the stitching and the a sewing machine is stopped, press (Needle position button) once to raise the needle. a a Needle position button Raise the presser - Brother International Innov-ís 950D | Users Manual - English - Page 63
). z Stitch settings return to their defaults if they are changed, when the machine is turned off or a different stitch is selected before the stitch setting is zigzag width. For details, refer to "Satin stitching using the sewing speed controller" (page 107). CAUTION z After adjusting the stitch - Brother International Innov-ís 950D | Users Manual - English - Page 64
be adjusted. z Press default. to return the setting to its CAUTION z If the stitches are bunched together, increase the stitch length. Continuing to sew with the stitches bunched together may result in the needle bending or breaking. c d a Wrong side of fabric b Right side of fabric c Upper - Brother International Innov-ís 950D | Users Manual - English - Page 65
bobbin correctly. z The level "4" on the tension dial is a guide for working normal fabrics (medium weight). However, the actual stitch should always sew a stitch sample and adjust stitch tension before beginning on the actual piece to be worked. z The machine may stop sewing if tension - Brother International Innov-ís 950D | Users Manual - English - Page 66
reverse/ reinforcement stitches Position the fabric under the presser foot, and d then press (Start/stop button) once. The sewing machine can be set to automatically sew reverse or reinforcement stitches at the beginning and end of the stitching. Depending on the selected stitch, reverse stitches - Brother International Innov-ís 950D | Users Manual - English - Page 67
is set for programmed thread-cutting and automatic reverse/reinforcement stitching. 2a 4 3b a Stop the machine and change the sewing direction. b Start the machine again. Automatically cutting the thread The sewing machine can be set to automatically cut the threads at the end of the stitching - Brother International Innov-ís 950D | Users Manual - English - Page 68
Memo z Press (Start/stop button) when you want to stop the sewing machine in the middle of sewing without programmed thread-cutting (for example, when you want to change the sewing direction). The sewing machine stops without programmed thread cutting. Press (Reverse/reinforcement stitch button) at - Brother International Innov-ís 950D | Users Manual - English - Page 69
only with utility stitches. The settings you saved will not be cleared if the machine is turned off. ■ To use a stitch length of 2.0 mm for stitch pattern is selected, the last settings saved are displayed even if the machine was turned off. If the settings are changed again and is pressed, - Brother International Innov-ís 950D | Users Manual - English - Page 70
stitching and the number of layers of fabric sewn, perform the trial sewing under the same conditions that will be used with your project. Changing the sewing direction When the stitching reaches a corner, stop the a sewing machine. Leave the needle lowered (in the fabric). If the needle remained up - Brother International Innov-ís 950D | Users Manual - English - Page 71
that the needle passes through the hookand-loop fastener by turning the handwheel and lower the needle into the hook-and-loop fastener before sewing. And then, sew the edge of the hookand-loop fastener at a slow speed. If the needle does not pass through the hook-andloop fastener, replace the needle - Brother International Innov-ís 950D | Users Manual - English - Page 72
fabric is aligned with either the right edge of the presser foot or a marking on the needle plate. ■ Aligning the fabric with the presser foot Sew while keeping the right edge of the presser foot aligned with a fixed distance from the edge of the fabric. a Seam b Presser foot c Centimeters d Inches - Brother International Innov-ís 950D | Users Manual - English - Page 73
. Stitch Setting Chart 72 Overcasting Stitches 78 Basic Stitching ...82 Blind Hem Stitching 84 Buttonhole Stitching/Button Sewing 87 Zipper Insertion...94 Sewing Stretch Fabrics and Elastic Tape 99 Appliqué, Patchwork and Quilt Stitching 101 Reinforcement Stitching 108 Eyelet Stitching...113 - Brother International Innov-ís 950D | Users Manual - English - Page 74
Foot Stitch Name Pattern Application Stitch Width [mm (inch)] Auto Manual 1 J Basic stitching, sewing gathers or pintucks, etc. 0.0 (0) 0.0-7.0 (0-1/4) Stitch Length [mm (inch)] Auto Manual Reverse/ Reinforcement Stitching 2.5 0.2-5.0 Yes (3/32) (1/64-3/16) (J) Reverse No Left - Brother International Innov-ís 950D | Users Manual - English - Page 75
Stitch Width [mm (inch)] Stitch Length [mm (inch)] Auto Manual Auto Manual Reverse/ Reinforcement Stitching 00 3m - o3 2.0 (1/16) 1.0-3.5 (1/ 64-3/16) (J) Reinforcement No Patchwork stitching, decorative J stitching and sewing overcasting on both pieces of fabric, such as 5.0 (3/16) - Brother International Innov-ís 950D | Users Manual - English - Page 76
[mm (inch)] Auto 4.0 (3/16) Manual 0.0-7.0 (0-1/4) Stitch Length [mm (inch)] Auto Manual Reverse/ Reinforcement Stitching 3.0 (1/8) 2.0-4.0 1.0 0.2-4.0 Yes (1/16) (1/64-3/16) (J) Reinforcement No Lace sewing, decorative N hemming, heirloom stitching, etc. 3.5 (1/8) 1.5-7.0 (1/16-1/4) - Brother International Innov-ís 950D | Users Manual - English - Page 77
[mm (inch)] Stitch Length [mm (inch)] Auto Manual Auto Manual Reverse/ Reinforcement Stitching 5.0 (3/16) 3.0-5.0 (1/8-3/16) 0.5 Automatic reinforcement No 58 Darning stitch 59 60 Bar tack stitch 61 Button-sewing stitch 62 Eyelet stitch 63 A Darning mediumweight fabrics 7.0 (1/4) 2.5-7.0 - Brother International Innov-ís 950D | Users Manual - English - Page 78
UTILITY STITCHES Other stitches Presser Foot Twin Needle Pattern Size Adjustable Stitching Density Adjustable Pattern Length/width Left/Right Flipping Stitch Type Pattern 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Decorative stitches N No - No Yes Yes 21 22 23 24 25 26 27 28 29 - Brother International Innov-ís 950D | Users Manual - English - Page 79
Presser Foot Twin Needle Pattern Size Adjustable Stitching Density Adjustable Pattern Length/width Left/Right Flipping Stitch Type Pattern 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Character stitches N (Gothic font) 31 32 33 34 35 36 37 38 39 40 - Brother International Innov-ís 950D | Users Manual - English - Page 80
that fray easily Stitch Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual Presser Foot 3.5 2.0 (1/8) (1/16) 2.5-5.0 (3/32 and the machine starts sewing. Attach overcasting foot "G". a G Position the fabric with the edge of the fabric c against the guide of the presser - Brother International Innov-ís 950D | Users Manual - English - Page 81
sew overcasting stitches with zigzag foot "J". Stitch Name Pattern Application Stitch Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual /stop button) is accidentally pressed and the machine starts sewing. Attach zigzag foot "J". a J Sew along the edge of the fabric with the - Brother International Innov-ís 950D | Users Manual - English - Page 82
[mm (inch)] Auto Manual 0.0 0.0-2.5 (0) (0-3/32) 3.5 (1/8) 5.0 (3/16) 3.5-5.0 (1/8-3/16) Stitch Length [mm (inch)] Auto Manual 2.5 0.2-5.0 (3/32) may occur if (Start/stop button) is accidentally pressed and the machine starts sewing. Position the side cutter so that side cutter pin c is aligned - Brother International Innov-ís 950D | Users Manual - English - Page 83
upper thread under the side cutter, e and then pull it out toward the rear of the sewing machine. Position the fabric in the side cutter. h The cut in the fabric should be positioned over the guide plate of the side cutter. Select a stitch. f • For details, refer to "Selecting stitching" (page 51 - Brother International Innov-ís 950D | Users Manual - English - Page 84
Auto Manual Stitch Length [mm (inch)] Auto Manual - - Presser Foot 1 Straight stitch Basic stitching and sewing gathers or injuries may occur if (Start/stop button) is accidentally pressed and the machine starts sewing. Basting Attach zigzag foot "J". a • For details on replacing the presser - Brother International Innov-ís 950D | Users Manual - English - Page 85
position) and the straight stitch (center needle position). a b When sewing is finished, cut the thread. f • For details, refer to )), the needle position will also change. By changing the stitch width and sewing with the right side of the presser foot aligned with the edge of the fabric - Brother International Innov-ís 950D | Users Manual - English - Page 86
[mm (inch)] Auto Manual Presser Foot 00 3m - o3 2.0 (1/16) 1.0-3.5 (1/16-1/8) R CAUTION ● Be sure to turn off the main power before replacing the presser foot. Otherwise, injuries may occur if (Start/stop button) is accidentally pressed and the machine starts sewing. Sew a blind hem according - Brother International Innov-ís 950D | Users Manual - English - Page 87
h free-arm sewing possible. • For details on free-arm sewing, refer to "Freearm sewing" (page 46). Slide the item that you wish to sew onto the i arm fabric with the edge of the folded j hem against the guide of the presser foot, and then lower the presser foot lever. R c 1 b a Wrong - Brother International Innov-ís 950D | Users Manual - English - Page 88
Wrong side of fabric b Right side of fabric Memo z For details, refer to "Adjusting the stitch width" (page 61). Sew with the fold of the hem against the l presser foot guide. Remove the basting stitching and reverse the m fabric. 1 2 a Wrong side of fabric b Right side of fabric - Brother International Innov-ís 950D | Users Manual - English - Page 89
stitches are available for sewing one-step buttonholes, and one stitch is available for attaching the button. Stitch Name Pattern Application 48 Horizontal buttonholes on thin and mediumweight fabrics Stitch Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual Presser Foot 49 - Brother International Innov-ís 950D | Users Manual - English - Page 90
pressed and the machine starts sewing. The names of parts of buttonhole foot "A", which is used for sewing buttonholes, are indicated below. Use chalk to mark on the fabric the position a and length of the buttonhole. 1 2 5 6 3 4 A a Button guide plate - Brother International Innov-ís 950D | Users Manual - English - Page 91
: For a button with a diameter of 15 mm (9/16 inch) and a thickness of 10 mm (3/8 inch), the button guide plate should be set to 25 mm (1inch) on the scale. 1 Position the fabric with the front end of the e refer to "Replacing the presser foot" (page 43). Buttonhole Stitching/Button Sewing 89 - Brother International Innov-ís 950D | Users Manual - English - Page 92
lever The buttonhole lever is positioned behind the bracket on the buttonhole foot. a Memo z If programmed thread-cutting is set, the sewing machine will sew reinforcement stitching, and then cut the thread automatically at the end of the stitching. Refer to "Automatically cutting the thread" (page - Brother International Innov-ís 950D | Users Manual - English - Page 93
use the seam ripper in any other way than how it is intended. Memo z For details, refer to "Adjusting the stitch width" (page 61). z Before sewing buttonholes, check the stitch length and width by sewing a trial buttonhole on a scrap piece of fabric. Buttonhole Stitching/Button - Brother International Innov-ís 950D | Users Manual - English - Page 94
woven fabrics, use a gimp thread. Hook the gimp thread onto the part of a buttonhole foot "A" shown in the illustration. Button sewing Buttons can be sewn on with the sewing machine. Buttons with two or with four holes can be attached. Measure the distance between the holes in the a button to be - Brother International Innov-ís 950D | Users Manual - English - Page 95
two holes closest to you. Then, slide the button so that the needle goes into the two holes toward the rear of the sewing machine, and then sew them in the same way. Pull the upper thread at the end of the i stitching to the wrong side of the fabric, and then tie - Brother International Innov-ís 950D | Users Manual - English - Page 96
(inch)] Auto Manual Presser Foot 3.5 0.0-7.0 2.5 0.2-5.0 (1/8) (0-1/4) (3/32) (1/64-3/16) I CAUTION ● Be sure to turn off the main power before replacing the presser foot. Otherwise, injuries may occur if (Start/stop button) is accidentally pressed and the machine starts sewing. There are many - Brother International Innov-ís 950D | Users Manual - English - Page 97
foot, refer to "Replacing the presser foot" (page 43). a Stitching b Right side of fabric c Basting stitching d End of zipper opening CAUTION ● When sewing, be sure that the needle does not touch the zipper, otherwise the needle may bend or break. Remove the basting stitching. j Zipper Insertion - Brother International Innov-ís 950D | Users Manual - English - Page 98
reverse stitches after reaching the zipper opening. • For details, refer to "Basic stitching" (page 82). Using a basting stitch, continue sewing to the c edge of the fabric. 1 3 2 4 a Wrong side of fabric Press the seam allowance so that the right side e (the side that will not be - Brother International Innov-ís 950D | Users Manual - English - Page 99
When you are about 5 cm (2 inches) from the j end of the zipper, stop the sewing machine with the needle lowered (in the fabric), and then raise the presser foot lever. Open the zipper and continue sewing. k CAUTION ● When using zipper foot "I", be sure to select the straight stitch (center needle - Brother International Innov-ís 950D | Users Manual - English - Page 100
not touch the zipper, otherwise the needle may bend or break. When you are about 5 cm (2 inches) from the o end of the zipper, stop the sewing machine with the needle lowered (in the fabric), and then raise the presser foot lever. Remove the basting stitching, open the zipper, p and then continue - Brother International Innov-ís 950D | Users Manual - English - Page 101
fabrics Stitch Width [mm (inch)] Auto Manual 0.0 0.0-7.0 (0) (0-1/4) Stitch Length [mm (inch)] Auto Manual Presser Foot 2.5 1.5-4.0 (3/32) (1/16 button) is accidentally pressed and the machine starts sewing. Stretch stitching Attach zigzag foot "J". a J Sew the fabric without stretching it. - Brother International Innov-ís 950D | Users Manual - English - Page 102
of the a fabric. Pin the elastic tape to the fabric at a few points to make sure that the tape is uniformly positioned on the fabric. Sew the elastic tape to the fabric while d stretching the tape so that it is the same length as the fabric. While pulling the fabric behind - Brother International Innov-ís 950D | Users Manual - English - Page 103
quilting, satin stitching Stitch Width [mm (inch)] Auto Manual 0.0-7.0 (0-1/4) 3.5 (1/8) Stitch Length [mm (inch)] Auto Manual 1.4 0.0-4.0 (1/16) (0-3/16) Presser Foot 19 (Start/stop button) is accidentally pressed and the machine starts sewing. Appliqué, Patchwork and Quilt Stitching 101 - Brother International Innov-ís 950D | Users Manual - English - Page 104
Basting stitching Attach zigzag foot "J". d J • For details on replacing the presser foot, refer to "Replacing the presser foot" (page 43). When sewing around corners, stop the machine with the needle in the fabric just outside of the appliqué, raise the presser foot lever, and then turn the fabric - Brother International Innov-ís 950D | Users Manual - English - Page 105
43). a 6.5 mm (1/4 inch) ■ For a seam allowance on the left side Align the left side of the presser foot with the edge of the fabric, and sew using stitch 22 . 1 a 6.5 mm (1/4 inch) Memo z To change the width of the seam allowance (needle position), refer to "Changing the needle position" (page 83 - Brother International Innov-ís 950D | Users Manual - English - Page 106
Quilting guide Note z Thread the needle manually when using the walking foot, or only attach the walking foot after threading the needle using the needle threader. z When sewing with the walking foot, sew at a speed between slow and medium. z When quilting, use a 90/14 home sewing machine needle - Brother International Innov-ís 950D | Users Manual - English - Page 107
Use the quilting guide to sew parallel stitches that are equally spaced. Insert the stem of the quilting guide into the a hole at the rear of the walking foot or presser foot holder. Walking foot 3 Presser foot holder Adjust the stem of the quilting guide so that b the guide aligns with the - Brother International Innov-ís 950D | Users Manual - English - Page 108
freely in any direction. When free-motion quilting, use the following instructions with the optional free-motion open toe quilting foot "O" (SA187, a Drop feed lever (as seen from the rear of the machine) X The feed dogs are lowered. Turn on the sewing machine, and then select a e stitch 3 or 24 . • - Brother International Innov-ís 950D | Users Manual - English - Page 109
. Select a stitch. f Attach zigzag foot "J". b J 3 • For details on replacing the presser foot, refer to "Replacing the presser foot" (page 43). Turn on the sewing machine, and then press c (Settings key) on the operation panel. • For details, refer to "Selecting stitching" (page 51). While - Brother International Innov-ís 950D | Users Manual - English - Page 110
. Stitch Name Pattern Application Stitch Width [mm (inch)] Auto Manual Triple stretch 4 stitch Reinforcing the seams of sleeves 0.0 and if (Start/stop button) is accidentally pressed and the machine starts sewing. Triple stretch stitching Use triple stretch stitching to reinforce sleeve - Brother International Innov-ís 950D | Users Manual - English - Page 111
Determine the desired length of the bar tack. a Set the button guide plate on buttonhole foot "A" to the desired length. (The distance between the markings on the presser foot scale is 5 mm (3/16 inch).) 1 • Pass the upper - Brother International Innov-ís 950D | Users Manual - English - Page 112
the needle is raised. Raise the presser foot lever, and then remove h the fabric. Memo z If programmed thread-cutting is set, the sewing machine will sew reinforcement stitching, and then cut the thread automatically at the end of the stitching. Refer to "Automatically cutting the thread" (page 65 - Brother International Innov-ís 950D | Users Manual - English - Page 113
torn can be darned. Darning is sewn as shown below. a 3 a a Reinforcement stitching Determine the desired length of the darning. a Set the button guide plate on buttonhole foot "A" to the desired length. (The distance between the markings on the presser foot scale is 5 mm (3/16 inch).) Select - Brother International Innov-ís 950D | Users Manual - English - Page 114
the needle is raised. Raise the presser foot lever, and then remove h the fabric. Memo z If programmed thread-cutting is set, the sewing machine will sew reinforcement stitching, and then cut the thread automatically at the end of the stitching. Refer to "Automatically cutting the thread" (page 65 - Brother International Innov-ís 950D | Users Manual - English - Page 115
)] Auto Manual 7.0, 6.0 or 7.0 5.0 (1/4) (1/4, 15/64 or 3/16) Presser Foot N CAUTION ● Be sure to turn off the main power before replacing the presser foot. Otherwise, injuries may 3 occur if (Start/stop button) is accidentally pressed and the machine starts sewing. Attach monogramming - Brother International Innov-ís 950D | Users Manual - English - Page 116
Sewing two pieces of fabric together across an open seam Stitch Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual stitching 2.5-7.0 (3/25-1/4) 0.5 0.1-1.0 (1/32) (1/64-3/16) 39 3.5 Lace sewing, decorative (1/8) hemming, heirloom stitching, 40 etc. 6.0 (15/64) 2.5 - Brother International Innov-ís 950D | Users Manual - English - Page 117
37 38 Decorative stitching Stitch Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual Presser Foot 6.0 (15/64) 1.5-7.0 1.6 1.0-4.0 5.0 if (Start/stop button) is accidentally pressed and the machine starts sewing. Fagoting Stitching across an open seam is called "fagoting". - Brother International Innov-ís 950D | Users Manual - English - Page 118
foot" (page 43). Select stitch 27 . b • For details, refer to "Selecting stitching" (page 51). Stitch along the edge of the fabric, making sure c not to sew directly on the edge of the fabric. Memo z For better results, apply spray starch onto the fabric and press with a hot iron before it is - Brother International Innov-ís 950D | Users Manual - English - Page 119
refer to "Adjusting the stitch length" (page 62) and "Adjusting the thread tension" (page 62). Pull out the threads for the straight stitches. g Sew parallel stitching at intervals of 1 cm (3/8 c inch). 1 a 1cm (3/8 inch) At the end of the stitching, the thread is pulled out about 5 cm (2 inches - Brother International Innov-ís 950D | Users Manual - English - Page 120
43). Select stitch 20 , and then increase the c thread tension. • For details, refer to "Selecting stitching" (page 51) and "Adjusting the thread tension" (page 62). Sew while making sure that the needle drops d slightly off the edge of the fabric. a a Needle drop point 118 - Brother International Innov-ís 950D | Users Manual - English - Page 121
the needle" (page 41). 3 Memo z Use a 130/705H 100/16 wing needle. z The needle threader cannot be used with the wing needle, otherwise the sewing machine may be damaged. Manually pass the thread through the eye of the needle from the front to the back. For details, refer to "Threading the needle - Brother International Innov-ís 950D | Users Manual - English - Page 122
with the wing needle, select a stitch width of 6.0 mm (15/64 inch) or less. Start sewing. d Attach monogramming foot "N". b CAUTION ● When sewing with the wing needle, select a stitch width of 6.0 mm (15/64 inch) or less, otherwise the needle may bend or break. ● After adjusting the stitch - Brother International Innov-ís 950D | Users Manual - English - Page 123
the screen is mirrored. Pull out several threads from two sections of a the fabric, separated by an unfrayed section of about 4 mm (3/16 inch). 3 Sew along the other edge of the frayed section f so that it looks like the previous stitching. N Press , and set the horizontal mirror g image key - Brother International Innov-ís 950D | Users Manual - English - Page 124
and threads When sewing thin, mediumweight or stretch fabrics, use the ball point needle. When sewing thick fabrics, use a 90/14 home sewing machine needle. In achieved. Be sure to sew a trial piece of fabric before sewing your project. In addition, while sewing, be sure to guide the fabric with your - Brother International Innov-ís 950D | Users Manual - English - Page 125
size is selected, small patterns can be combined and connected. z If multiple patterns have been combined, the size of each selected pattern can be specified. Sewing the Various Built-in Decorative Patterns 123 - Brother International Innov-ís 950D | Users Manual - English - Page 126
UTILITY STITCHES Changing the length for satin stitches The length for one satin stitch can be changed in five gradations. Press (Utility stitch key) on the a operation panel, and then select (Satin stitch). Adjusting the character spacing The space between alphanumeric characters can be - Brother International Innov-ís 950D | Users Manual - English - Page 127
a If the pattern is not sewn correctly, follow the steps below to adjust the sewing. Press f panel. (Settings key) on the operation 3 • For details, refer adjustment is sewn. X The sewing machine stops after sewing the pattern has finished. Sewing the Various Built-in Decorative Patterns 125 - Brother International Innov-ís 950D | Users Manual - English - Page 128
or combined utility stitch types. Press h (Back key). X It returns to the screen for adjusting the pattern. Select once again, start the sewing i machine and check the stitching. X Continue adjusting the pattern until it is sewn correctly. Select the first pattern. b X The first pattern is - Brother International Innov-ís 950D | Users Manual - English - Page 129
For details, refer to "Saving patterns" (page 129). Memo z If repeated sewing is set, the pattern is repeatedly sewn until the sewing machine is stopped. z If the sewing machine is turned off, the repeated/single sewing setting returns to its default setting. z If pressed again, it turns to - Brother International Innov-ís 950D | Users Manual - English - Page 130
UTILITY STITCHES ■ Mirroring a pattern image After a single pattern has been selected, press a to mirror the pattern image horizontally. ■ Checking the pattern When the specified pattern is not displayed on the screen, check the pattern using the following steps. Press . a X The screen for - Brother International Innov-ís 950D | Users Manual - English - Page 131
X "Saving..." appears while the pattern is being saved. After the pattern is saved, the initial screen appears again. • Do not turn off the sewing machine while the pattern is being saved, otherwise the pattern data may be lost. ■ Retrieving a pattern Press . a Recall the saved pattern. X The saved - Brother International Innov-ís 950D | Users Manual - English - Page 132
UTILITY STITCHES ■ Deleting a saved pattern A saved pattern in a pocket can be deleted. Press . a Select the pocket where the pattern you wish b to delete is saved. indicates pockets where patterns are already saved. X The selected pocket is shown in reverse highlighting, and the saved pattern - Brother International Innov-ís 950D | Users Manual - English - Page 133
intersections in the grid, and then link those points with a continuous straight line. Draw a sketch of the pattern on the grid sheet a set. 3 Determine the sewing order. d Draw the pattern as one continuous line and with the start point and the end point of the design at the same height. 10 - Brother International Innov-ís 950D | Users Manual - English - Page 134
Follow the pattern drawn on the grid sheet and program the pattern into the sewing machine. Attach monogramming foot "N". a • For details, refer to "Replacing the is single stitching, and gives triple stitching. X The embroidery screen appears. Specify the various stitching settings, such as h - Brother International Innov-ís 950D | Users Manual - English - Page 135
Editing the pattern data To edit the pattern you entered, press . The screen for editing the pattern appears. You can move, insert and delete points. When you have finished editing the pattern, press to go back to the screen for entering the pattern, and then follow steps f through h on - Brother International Innov-ís 950D | Users Manual - English - Page 136
UTILITY STITCHES Examples of designs Enter each of the points indicated in the table to sew the sample stitch. Point Point 1 0 0 21 38 13 2 12 0 22 35 14 3 18 3 23 32 13 4 22 6 24 30 10 5 23 10 25 32 6 6 21 - Brother International Innov-ís 950D | Users Manual - English - Page 137
embroidering are described in this chapter. Embroidering Neatly 136 Attaching the Embroidery Foot 138 Attaching the Embroidery Unit 141 Preparing the Fabric 144 Attaching the Embroidery Frame 148 Selecting Embroidery Patterns 150 Embroidering ...157 Editing and Saving Patterns 162 Using the - Brother International Innov-ís 950D | Users Manual - English - Page 138
does not hang off the table where the sewing machine is placed. If embroidery is done with the fabric hanging off, the embroidery unit movement may be impaired, this could cause the pattern to sew incorrectly. For the bobbin thread, use the embroidery bobbin thread. For details, refer to "Optional - Brother International Innov-ís 950D | Users Manual - English - Page 139
. For details on adjusting the layout and the size, refer to "Adjusting the layout and the size" (page 162). p 9 Embroidery thread setup Set up embroidery thread according to the pattern. For details on setting up the thread, refer to "Upper Threading" (page 31). Embroidering Neatly 137 - Brother International Innov-ís 950D | Users Manual - English - Page 140
Foot This section describes how to attach the embroidery foot "Q". Attaching the embroidery foot Attach the embroidery foot "Q" when embroidering. Have the included embroidery foot "Q" and a screwdriver ready. Turn off the sewing machine. b a b a Embroidery foot bar b Caught by the presser foot - Brother International Innov-ís 950D | Users Manual - English - Page 141
in the lever with your finger, fit g the embroidery foot bar over the needle clamp screw to attach the embroidery foot to the presser foot bar. c b a needle may hit the presser foot and break or bend. ● Before sewing, always turn the handwheel toward you (counterclockwise) slowly to make sure - Brother International Innov-ís 950D | Users Manual - English - Page 142
Attach the presser foot holder. e • For details, refer to "Removing and attaching the presser foot holder" (page 45). CAUTION z Before removing the embroidery foot, be sure to turn off the sewing machine. Otherwise, injuries may occur if one of the operation buttons is accidentally pressed and the - Brother International Innov-ís 950D | Users Manual - English - Page 143
unit ready. Note z Do not touch the connector in the Turn off the sewing machine. a 4 embroidery unit connector slot. The connector could be damaged, and it may cause malfunctions. z Do not lift up on the embroidery carriage, and do not forcefully move it. It may cause malfunctions. Note - Brother International Innov-ís 950D | Users Manual - English - Page 144
insert the connector into the connection port. z Do not push on the carriage when attaching the embroidery unit to the machine, otherwise damage to the embroidery unit may result. Turn on the sewing machine. d a Carriage CAUTION ● Do not put your hands or other objects near the carriage. It may - Brother International Innov-ís 950D | Users Manual - English - Page 145
unit Make sure that the sewing machine is completely stopped and follow the instructions below. Remove the embroidery frame. a • For details on removing the embroidery frame, refer to "Removing the embroidery frame" (page 149). Press , and then press . b Hold the release button on the - Brother International Innov-ís 950D | Users Manual - English - Page 146
parts, visit [http://www.brother.com/], or [http:// www.brothermall.com] (in USA). a c b a Fabric b Size of embroidery frame c Stabilizer material with a steam iron. CAUTION ● Always use stabilizer material when sewing embroidery projects. The needle may break or bend if you embroider without - Brother International Innov-ís 950D | Users Manual - English - Page 147
on b top of the outer frame. Have the right side of the cloth up. ■ Embroidery frame (small) [option] Patterns with a height of up to 2 cm (1 inch) fabric. Line up on the inner frame and on outer frame. ■ Embroidery frame (large) [option] Embroidery can be done in an area with a height of up to - Brother International Innov-ís 950D | Users Manual - English - Page 148
(right side) d Stabilizer material e Ledge of outer frame • Press down firmly until the inner frame is securely pressed against the ledge of the outer frame. Embroidery sheet (large) [option] Make a mark with a chalk pen at the center of a the position for the pattern to be embroidered - Brother International Innov-ís 950D | Users Manual - English - Page 149
thin pieces like ribbon are being embroidered, use stabilizer material as a base to stretch on the frame. We recommend stabilizer material for all embroidery. a b c a b a Base line b Mark Place the inner frame with the fabric on the d outer frame and stretch the fabric. • For details, refer to page - Brother International Innov-ís 950D | Users Manual - English - Page 150
, the presser foot may hit the embroidery frame, resulting in injury. CAUTION ● Do not touch the start/stop button, needle position button or reverse/ reinforcement stitch button. If one of the buttons is accidentally pressed, the machine will begin sewing and your finger may be pricked with - Brother International Innov-ís 950D | Users Manual - English - Page 151
lever even further. Make sure that the sewing machine is completely stopped and follow the instructions below. Raise the presser foot lever. a a a Presser foot lever Press (Needle position button) once or b twice to raise the needle. a Remove the embroidery frame. e CAUTION ● Do not touch the - Brother International Innov-ís 950D | Users Manual - English - Page 152
embroidery patterns available and the procedure for selecting a pattern. Copyright information Embroidery pattern types The patterns saved in the sewing machine and embroidery according to the instructions displayed on the screen. For details, refer to "Selecting an embroidery pattern" (page 155 - Brother International Innov-ís 950D | Users Manual - English - Page 153
language or change the thread color display or other settings. e Press to get help on embroidery unit attachment, embroidery frame attachment, etc. f Press this key to save embroidery patterns and the alphanumeric characters in the machine's memory. Selecting Embroidery Patterns 151 - Brother International Innov-ís 950D | Users Manual - English - Page 154
) THREAD# is selected.) •EMBROIDERY (POLYESTER) THREAD# •COUNTRY (COTTON) THREAD# •MADEIRA POLY THREAD# •MADEIRA RAYON THREAD# •SULKY THREAD# •ROBISON-ANTON POLY THREAD# When a specific pattern is selected, press this key and then, press to switch the display. The sewing settings such as the - Brother International Innov-ís 950D | Users Manual - English - Page 155
Press this key when you want to change the color, character by character in character embroidery. Since the sewing machine stops at the end of each character, the upper thread is changed as you sew. Press this key again to cancel multicolor. Memo z Keys that appear surrounded with a dotted line - Brother International Innov-ís 950D | Users Manual - English - Page 156
Memo z When "The pattern is too large for the embroidery frame" is displayed, no more characters can be input. z Characters from different fonts (sans serif and serif, etc.) cannot be combined. Select the alphanumeric characters. a - Brother International Innov-ís 950D | Users Manual - English - Page 157
in the machine's memory. 70 Embroidery patterns Memo z Refer to "Embroidery Pattern Color Change Table" in the Quick reference guide for samples 12 stitch types. Memo z Refer to "Frame patterns" in the Quick reference guide for frame pattern shapes and stitches. Press . a 4 X The pattern - Brother International Innov-ís 950D | Users Manual - English - Page 158
using (Previous page key) and (Next page key), and select from the 12 stitches. Insert the embroidery card in the embroidery b card slot on the right side of the sewing machine. Face the arrow on the embroidery card toward you, and insert it in the direction of the arrow. X When a stitch is - Brother International Innov-ís 950D | Users Manual - English - Page 159
the steps for embroidering and appliquéing. Checking the pattern before embroidering X The frame moves to indicate the entire embroidering area. The embroidery frame is moved to indicate the embroidering position. Closely watch the frame to check that the pattern will be sewn at the correct - Brother International Innov-ís 950D | Users Manual - English - Page 160
embroidery thread of the color shown a on the screen. c a b d e a Embroidery frames crystal display) operation" (page 151). Set the embroidery thread, and thread the b needle. • Refer to lower the presser foot. Pass the thread through the embroidery foot c hole, and hold it lightly in your left - Brother International Innov-ís 950D | Users Manual - English - Page 161
Set up embroidery thread for the next color, i and repeat steps b through h. X When the last color is sewn, "Finished sewing." will embroidery frame may be hit by the presser foot and cause injury or needle breakage. After progressing 5-6 stitches, press f (Start/stop button) to stop the machine - Brother International Innov-ís 950D | Users Manual - English - Page 162
base fabric on the embroidery e frame. Set up the thread for appliquéing. f Lower the presser foot lever, and press g (Start/stop button). Lower the presser foot lever, and press c (Start/stop button). X The cut-out for the appliqué piece is sewn, and the sewing machine stops. a b a Cut-out line - Brother International Innov-ís 950D | Users Manual - English - Page 163
the appliqué is stitched, and the sewing machine stops. 4 Memo z When "APPLIQUE MATERIAL", "APPLIQUE POSITION" and "APPLIQUE" are displayed, a specific color thread does not appear. Use a proper color thread to match the appliqué piece. Follow the instructions on the screen, and j change thread - Brother International Innov-ís 950D | Users Manual - English - Page 164
d Change position keys e Size key/Layout key f Rotation key g Horizontal mirror image key h Trial key i Starting point key j Distance from the center k Embroidery size Embroidery frame size The size of embroidery frame that can be used is displayed. When the smaller mark is grayed out in the display - Brother International Innov-ís 950D | Users Manual - English - Page 165
position. Use the Change position keys after you have changed the size of the pattern or reversed it. z The embroidery patterns you have edited or adjusted can be saved in the sewing machine's memory. For details, refer to "Saving patterns" (page 174). Layout key Press this key to move to rotation - Brother International Innov-ís 950D | Users Manual - English - Page 166
z You can also check the pattern size and distance from the center by pressing after beginning embroidering. z The embroidery patterns you have edited or adjusted can be saved in the sewing machine's memory. For details, refer to "Saving patterns" (page 174). Adjusting the thread tension It is very - Brother International Innov-ís 950D | Users Manual - English - Page 167
end of the thread longer than usual. Then reset the fabric in the embroidery frame, in a position where you can sew "DEF". Press c (Back key). 4 a b a Embroidery start position b Embroidery end position Enter "DEF" and press . i Press . d Press . j Press . e Press k to turn it - Brother International Innov-ís 950D | Users Manual - English - Page 168
of "ABC". a a Embroidery end position Lower the presser foot, and then press m (Start/Stop button) to embroider "DEF". Resewing When the wrong upper thread color has been sewn, it can be resewn with the correct color. Press (Start/stop button) to stop the a sewing machine. Press . b Press - Brother International Innov-ís 950D | Users Manual - English - Page 169
is stopped before it is complete, check the current needle count and layout before turning off the sewing machine. Memo z When the sewing machine is turned off, the embroidery size and layout return to the original setting. If you have changed the layout, you need to adjust it again. Press - Brother International Innov-ís 950D | Users Manual - English - Page 170
color you want to embroider. Note z Always detach the embroidery unit when you move the sewing machine. Turn on the sewing machine, and then select f the pattern. Memo z If you have changed the embroidery size and/or layout before turning off the machine, make the same setting changes again before - Brother International Innov-ís 950D | Users Manual - English - Page 171
. Using data other than that saved using one of our embroidery software programs or sewing machines may cause the embroidery machine to malfunction. ■ Types of USB Media That Can Be Used Embroidery data can be retrieved from a USB flash drive (USB flash memory) of any size. 4 Note z Only a USB - Brother International Innov-ís 950D | Users Manual - English - Page 172
designs contain too many colors (this number may vary within the designs themselves), it may not be possible to transfer an embroidery pattern to the machine, even if there are less than 200 files (including folders) in the USB media. If this occurs, you will also need to reduce the number - Brother International Innov-ís 950D | Users Manual - English - Page 173
precautions" (page 169 to 170). Note z Be sure to read the all precautions of "Embroidery data precautions" (page 169 to 170) and observe them. Otherwise, the pattern files may not be retrieved into the machine correctly. Safely remove the USB media from the USB e port on the computer. (Refer to - Brother International Innov-ís 950D | Users Manual - English - Page 174
EMBROIDERY Insert the USB media into the USB port on the f machine. Memo z Names of folders are appears, the USB media may contain either more than 200 patterns (including folders) or the embroidery designs may contain too many colors (although there may be no more than 200 patterns). In - Brother International Innov-ís 950D | Users Manual - English - Page 175
you have selected a folder *1) The display of this part differs depending 4 on the operation in step h. X The saved pattern is retrieved. X The embroidery screen appears, and you can embroider the retrieved pattern. X Pattern files in the folder are displayed. Go to step i. ■ When you have - Brother International Innov-ís 950D | Users Manual - English - Page 176
patterns and the alphanumeric characters you have customized can be saved in the sewing machine's memory. Since the saved patterns will not be erased when the power is turned off, you can always retrieve them for embroidery. This is convenient for saving names and the like. You can save up - Brother International Innov-ís 950D | Users Manual - English - Page 177
5 APPENDIX The various maintenance and troubleshooting procedures are described in this chapter. Care and Maintenance 176 Troubleshooting ...178 Upgrading Your Machine's Software Using USB Media 188 Index ...189 - Brother International Innov-ís 950D | Users Manual - English - Page 178
. Turn off the sewing machine. a Unplug the power supply cord from the power b supply jack on the right side of the sewing machine. a a Needle plate before cleaning the machine. Otherwise, injuries or an electric shock may occur. Remove the flat bed attachment or the c embroidery unit if either - Brother International Innov-ís 950D | Users Manual - English - Page 179
scratched. Otherwise, the upper thread may become tangled, the needle may break or sewing performance may suffer. For a new bobbin case (part code: XE7560-001 (green marking)), contact your nearest authorized service center. ● Be sure that the bobbin case is correctly installed, otherwise the needle - Brother International Innov-ís 950D | Users Manual - English - Page 180
://solutions.brother.com]. If the problem persists, contact your dealer or the nearest authorized service center. Symptom Probable Cause Remedy The machine is not turned on. Turn on the machine. The start/stop button was not pressed. Press the start/stop button. The sewing machine does not - Brother International Innov-ís 950D | Users Manual - English - Page 181
your dealer or the nearest authorized service center. - A bobbin designed specifically for this machine is not used. Incorrect bobbins will . Correctly pass the thread through the bobbin-winding thread guide. Move the sewing speed controller to the right (so that the speed Troubleshooting 179 - Brother International Innov-ís 950D | Users Manual - English - Page 182
machine. The thread is tangled on the wrong side of the fabric. The upper thread was not threaded correctly. Correct the upper threading. The upper thread was not threaded correctly. Correct the upper threading. Make sure that the thread is hanged on the thread guide or sew with stitch - Brother International Innov-ís 950D | Users Manual - English - Page 183
the correct position. Press the needle position button. page 32 The sewing lamp The sewing lamp is damaged. does not come on. The machine is not turned on. Contact your dealer or the nearest authorized service center. Turn on the machine. page 17 Nothing appears in the LCD. The brightness of - Brother International Innov-ís 950D | Users Manual - English - Page 184
and the fabric is hanging off the table. If embroidery is done with the fabric hanging off the table, the embroidery unit movement will be impaired. Support the fabric while embroidering. The fabric is catching. It is pinched. Stop the sewing machine and set the fabric up correctly. The carriage - Brother International Innov-ís 950D | Users Manual - English - Page 185
at a LCD screen other than the sewing LCD screen. The start/stop button machine is deleting a previously saved pattern while in embroidery edit mode. The start/stop button was pressed while the foot controller was 8 connected. You tried to use the foot controller for embroidery. Troubleshooting - Brother International Innov-ís 950D | Users Manual - English - Page 186
, cross stitches or combined utility stitches. 17 The memory is full and the pattern cannot be saved. 18 You pressed the back key or the embroidery key when a pattern was selected or the utility stitch key when a stitch is selected. 184 - Brother International Innov-ís 950D | Users Manual - English - Page 187
by pressing the manual memory key. You tried to select an embroidery pattern or change the layout when 20 the needle was down. The machine is turned on while the needle is lowered and the embroidery unit is attached 27 Bobbin thread has run out. Little bobbin thread remains. Troubleshooting 185 - Brother International Innov-ís 950D | Users Manual - English - Page 188
and hitting the needle plate, etc., so the sewing machine stops (refer to page 178). 31 You tried to use a function that cannot be used when the embroidery unit is attached. An Embroidery Memory Card that may not compatible with your machine has been inserted. • Certain licensed designs cannot - Brother International Innov-ís 950D | Users Manual - English - Page 189
setting screen appears. Press c (Next page key) twice. Press OFF for the buzzer. d Turn off the sewing machine, then turn it on d again. Operation beep Each time a key is pressed you will hear one beep. If . Press e (Back key). X The initial stitch screen appears again. Troubleshooting 187 - Brother International Innov-ís 950D | Users Manual - English - Page 190
sewing machine. When an upgrade program is available on our website at "http://solutions.brother.com", please download the file(s) following the instructions the machine's software is upgraded, saved combinations of character and decorative stitches are erased. However, saved embroidery patterns - Brother International Innov-ís 950D | Users Manual - English - Page 191
types 150 bobbin winding 22 bobbin-winding thread guide 11, 24 embroidery sets 9 embroidery sheet 146 button sewing 92 buttonhole lever 12, 90 embroidery threads 136 embroidery unit connector slot 11 buttonhole sewing 88 embroidery unit installation 141 buttonhole stitching 87 - Brother International Innov-ís 950D | Users Manual - English - Page 192
LCD button 152 LCD messages 183 LCD operation 18 M machine surface cleaning 176 main power switch 12, 17 maintenance 176 manual needle threading 36 memory key 14 mirroring stitches 66 My Custom Stitch 131 N needle bar thread guide 12, 34 needle condition 40 needle plate 12, 70 needle - Brother International Innov-ís 950D | Users Manual - English - Page 193
thread guide disk 12, 34 thread spools 31 thread take-up lever 11, 34 thread tension adjustment 62, 164 threading 31 threading bobbin 22 threading needle 31 threading needle manually 36 tips 68 touch panel 14 trial sewing 68 triple stretch stitch 82, 99, 108 troubleshooting 178 Index - Brother International Innov-ís 950D | Users Manual - English - Page 194
- Brother International Innov-ís 950D | Users Manual - English - Page 195
- Brother International Innov-ís 950D | Users Manual - English - Page 196
English 885-V95/V97 XE7929-001 Printed in China
Product Code
885-V95/V97
GETTING READY
SEWING BASICS
UTILITY STITCHES
EMBROIDERY
APPENDIX
Computerized Embroidery and Sewing Machine
Operation Manual
Please visit us at
where you can get product support and answers to
frequently asked questions (FAQs).