Brother International LB-6800PRW Users Manual - English

Brother International LB-6800PRW Manual

Get Brother International LB-6800PRW PDF manuals and user guides View all Brother International LB-6800PRW manuals
Add to My Manuals
Save this manual to your list of manuals

Brother International LB-6800PRW manual content summary:

  • Brother International LB-6800PRW | Users Manual - English - Page 1
    Computerized Embroidery and Sewing Machine Operation Manual Product Code 885-V31/V32/V33 GETTING READY SEWING BASICS UTILITY STITCHES EMBROIDERY APPENDIX Please visit us at http://solutions.brother.com where you can get product support and answers to frequently asked questions (FAQs).
  • Brother International LB-6800PRW | Users Manual - English - Page 2
  • Brother International LB-6800PRW | Users Manual - English - Page 3
    movements, otherwise you may injure your back or knees. 4 Always keep your work area clear: • Never operate the machine with any air openings blocked. Keep ventilation openings of the sewing machine and foot control free from the build up of lint, dust, and loose cloth. • Do not store objects on the
  • Brother International LB-6800PRW | Users Manual - English - Page 4
    follow the troubleshooting table in the back of the operation manual to inspect and adjust the machine yourself. If the problem persists, please consult your local authorized Brother dealer. Use this machine only for its intended use as described in the manual. Use accessories recommended by the
  • Brother International LB-6800PRW | Users Manual - English - Page 5
    the plug supplied with this equipment, you should contact your authorized dealer to obtain the correct lead. FOR USERS IN AUSTRALIA AND NEW ZEALAND This sewing machine is not intended to be used by young children, and assistance may be required if used by a person with a disability. 3
  • Brother International LB-6800PRW | Users Manual - English - Page 6
    Contents Introduction ...1 Important Safety Instructions 1 Machine Features ...7 Accessories ...8 Included accessories ...8 Optional accessories ...9 Names of Machine Parts and Their Functions 10 Front view...10 Needle and presser foot section ...11 Right-side/rear view ...11 Operation
  • Brother International LB-6800PRW | Users Manual - English - Page 7
    a side zipper ...92 Sewing Stretch Fabrics and Elastic Tape 95 Stretch stitching ...95 Elastic attaching ...96 Appliqué, Patchwork and Quilt Stitching 97 Appliqué stitching ...98 Patchwork (crazy quilt) stitching ...99 Piecing ...99 Quilting ...100 Free-motion quilting ...102 Reinforcement
  • Brother International LB-6800PRW | Users Manual - English - Page 8
    an embroidery card ...138 Embroidering...139 Embroidering a pattern ...139 Appliquéing ...141 Editing and Saving Patterns 143 Adjusting the layout and the size...143 Adjusting the thread tension ...145 Connecting character patterns ...146 Resewing ...147 Thread runs out partway through a design
  • Brother International LB-6800PRW | Users Manual - English - Page 9
    to sew. A red or orange light indicates an error or that the machine is warming up (page 12). h Easy-to-use needle threader You can thread the needle easily by one press of a lever (page 32). i Embroidery You can embroider built-in embroidery patterns, characters, framed decorations, and designs
  • Brother International LB-6800PRW | Users Manual - English - Page 10
    accessories Note z Foot controller: Model T This foot controller can be used on the machine with product code 885-V31/V32/V33.The product code is mentioned on the machine rating plate. z The securing screw on the side of the presser foot holder is available through your authorized dealer. (Part
  • Brother International LB-6800PRW | Users Manual - English - Page 11
    XC2691-023 XC3098-051 XD0810-031 No. Part Name 18 Spool cap (small) 19 Extra spool pin 20 Spool net 4 Zipper foot "I" X59370-021 21 Foot controller 5 Zigzag foot "J" (on machine) 6 Blind stitch foot "R" 7 Button fitting foot "M" 8 Seam ripper 9 Bobbin (4) Bobbin clip (3) 10 Needle set 11 Twin
  • Brother International LB-6800PRW | Users Manual - English - Page 12
    below. Before using the sewing machine, carefully read these descriptions to learn the names of the machine parts. Front view a Thread guide cover (page 24, 33) Pass the thread under this thread guide cover when winding the bobbin thread and threading the machine. b Thread guide (page 24, 33) Pass
  • Brother International LB-6800PRW | Users Manual - English - Page 13
    138) Insert the embroidery card. d Air vent The air vent allows the air surrounding the motor to be exchanged. Do not cover the air vent while the sewing machine is being used. e Main power switch (page 17) Use the main power switch to turn the sewing machine on and off. f Foot controller jack (page
  • Brother International LB-6800PRW | Users Manual - English - Page 14
    changes color according to the machine's operation mode. Green: Red: Orange: The machine is ready to sew or is sewing. The machine can not sew. The machine is winding the bobbin thread, or the bobbin winder shaft is moved to the right side. Memo z When the foot controller is plugged in, (Start
  • Brother International LB-6800PRW | Users Manual - English - Page 15
    , and more. i Sewing machine help key Press to get help on using the sewing machine. Displays simple explanations of setting upper thread / bobbin winding / setting bobbin thread / needle replacement / embroidery unit attachment / embroidery frame attachment / embroidery foot attachment / presser
  • Brother International LB-6800PRW | Users Manual - English - Page 16
    14
  • Brother International LB-6800PRW | Users Manual - English - Page 17
    various preparations required before starting to sew are described in this chapter. Turning the Machine On/Off 16 LCD (Liquid Crystal Display) Operation 18 Winding/Installing the Bobbin 22 Upper Threading ...31 Replacing the Needle 39 Replacing the Presser Foot 43 Sewing Cylindrical Pieces 46
  • Brother International LB-6800PRW | Users Manual - English - Page 18
    On/Off This section explains how to turn the sewing machine on and off. Power supply precautions Be sure to . ● Do not touch the plug with wet hands. Electric shock may result. ● When unplugging the machine, always turn off the main power first. Always grasp the plug to remove it from the outlet.
  • Brother International LB-6800PRW | Users Manual - English - Page 19
    supply cord into the power supply jack on the right side of the Make sure that the machine is not sewing. a machine. Press the left side of the main power switch on b the right side of the machine to turn the Insert the plug of the power supply cord into a b house hold electrical outlet
  • Brother International LB-6800PRW | Users Manual - English - Page 20
    the front of the sewing machine. Change the screen on Presser foot to be used c Stitches d Stitch settings and twin needle sewing e sewing and needle stop position Memo z A different screen is displayed when the embroidery unit is attached. The details are explained in "Selecting an embroidery
  • Brother International LB-6800PRW | Users Manual - English - Page 21
    Details Settings Specifies where the needle is positioned when the sewing machine is stopped. Down Up Allows the stitch width to be adjusted with the sewing speed controller (page 58). Changes the thread color display on the embroidery screen (page 133). Thread color/Time to embroider/Needle
  • Brother International LB-6800PRW | Users Manual - English - Page 22
    settings are complete, press d (Back key). X The initial stitch screen appears again. Memo z "NO" is the individual number for the sewing machine. z "VERSION" is the program version which is installed in the sewing machine. z Settings that are changed are saved even if the power is turned off. 20
  • Brother International LB-6800PRW | Users Manual - English - Page 23
    to the item 1 selection screen. bobbin winding / setting bobbin thread / needle replacement / embroidery unit attachment / Example: Upper threading embroidery frame attachment / embroidery foot attachment / presser foot replacement on the LCD. Turn on the sewing machine. a X The LCD comes on
  • Brother International LB-6800PRW | Users Manual - English - Page 24
    the machine. ● The included bobbin was designed specifically for this sewing machine. If bobbins from other models are used, the machine will not operate correctly. Use only the included bobbin or bobbins of the same type (part code: SA156, SFB (XA5539-151)). 11.5 mm (7/16 inch) Actual size This
  • Brother International LB-6800PRW | Users Manual - English - Page 25
    be damaged. ● Three spool cap sizes are available, allowing you to choose a spool cap that best fits the size of spool being used. If the spool cap is too small for the spool being used, the thread may catch on the slit in the spool or the machine may be damaged. ● Winding/Installing the Bobbin 23
  • Brother International LB-6800PRW | Users Manual - English - Page 26
    , pulling it in as far as possible. c d a Spool net b Spool c Spool cap d Spool pin Pull the thread from the spool and pass the g thread under the hook of thread guide. a a Thread guide 24 a a Bobbin-winding thread guide Make sure that the thread passes under the pretension disk. b c d b Hook
  • Brother International LB-6800PRW | Users Manual - English - Page 27
    /stop button) once to stop the machine. When the foot controller is plugged in, remove your foot from the foot controller. X The bobbin winding will stop. CAUTION ● When the bobbin winding stops or becomes slow, stop the machine. Otherwise, the sewing machine may be damaged. Winding/Installing the
  • Brother International LB-6800PRW | Users Manual - English - Page 28
    presser, otherwise the machine may be damaged; you cannot wind off the thread by removing the screw. a a Screw of the bobbin winder presser If the thread become tangled under the bobbin a winder seat, press (Start/stop button) once to stop the bobbin winding. When the foot controller is plugged in
  • Brother International LB-6800PRW | Users Manual - English - Page 29
    shown below. ● The included bobbin was designed specifically for this sewing machine. If bobbins from other models are used, the machine will not operate correctly. Use only the included bobbin or bobbins of the same type (part code: SA156, SFB (XA5539-151)). Actual size 11.5 mm (7/16 inch) This
  • Brother International LB-6800PRW | Users Manual - English - Page 30
    ) once or a twice to raise the needle, and then raise the presser foot lever. a Insert the bobbin into the bobbin case with f your right hand. b a Needle position button b Presser foot lever Turn off the sewing machine. b Slide the bobbin cover latch to the right. c a b • Be sure to insert the
  • Brother International LB-6800PRW | Users Manual - English - Page 31
    is finished. You can begin sewing without pulling up the bobbin thread. Next, thread the upper thread. Continue with the procedure in "Upper Threading" (page 31). Memo z When making gathers or before free-motion quilting, pull up the bobbin thread by following the procedure in "When pulling
  • Brother International LB-6800PRW | Users Manual - English - Page 32
    upward to pull e out the end of the bobbin thread. Pull out about 10-15 cm (4-5 inches) of the f bobbin thread under the presser foot toward the rear of the machine. Reattach the bobbin cover. g Insert the tab in the lower-left corner of the bobbin cover, and then lightly press down on the right
  • Brother International LB-6800PRW | Users Manual - English - Page 33
    threading the upper thread, carefully follow the instructions. If the upper threading is not correct, the thread may become tangled or the needle may bend or break. ● The needle threader can be used with a 75/11 through 100/16 home sewing machine needle. When using special thread such as transparent
  • Brother International LB-6800PRW | Users Manual - English - Page 34
    button) until it is. Raise the presser foot lever. b a a a Presser foot lever X The presser foot is raised. Memo z If the presser foot is not raised, the sewing machine cannot be threaded. a Mark on handwheel Pick up the spool pin and remove the spool d cap that is inserted onto the spool pin
  • Brother International LB-6800PRW | Users Manual - English - Page 35
    below. 1 CAUTION ● If the spool or the spool cap is not positioned correctly, the thread may become tangled around guide. a a Thread guide a b d c a Thread guide cover b Thread guide spring c Thread d When the presser foot lever is lowered Note z When passing the thread behind the thread guide
  • Brother International LB-6800PRW | Users Manual - English - Page 36
    the thread with your right hand, as shown. a b a a Notch of the thread guide b Thread guide disc Cut the thread with the cutter on the left side n of the machine. a a Thread cutter a Needle bar thread guide Lower the presser foot lever to lower the l presser foot. a a Presser foot lever 34
  • Brother International LB-6800PRW | Users Manual - English - Page 37
    machine as much as possible to make the hook turn. Raise the needle threader lever slowly. p Ta a 1 a Needle threader lever a Needle threader lever Raise the presser foot a button. If a button is accidentally pressed, the machine starts sewing, and your finger may be pricked with the needle or
  • Brother International LB-6800PRW | Users Manual - English - Page 38
    thread" (page 32). Manually thread the left needle with the upper c thread. Pass the thread through the eye of the needle from the front. CAUTION ● The needle threader cannot be used with the twin needle. If the needle threader is used with the twin needle, the sewing machine may be damaged. 36
  • Brother International LB-6800PRW | Users Manual - English - Page 39
    f bar thread guide, manually thread the right needle. Pass the thread through the eye of the needle from the front. 1 a Bobbin winder shaft b needle, the sewing machine may be damaged. Attach zigzag foot "J". g For details on changing the presser foot, refer to "Replacing the Presser Foot" (page 43
  • Brother International LB-6800PRW | Users Manual - English - Page 40
    the sewing direction, press (Needle position button) to raise the needle from the fabric, and then raise the presser foot lever and turn the fabric. CAUTION ● Do not try turning the fabric with the twin needle left down in the fabric, otherwise the needle may break or the machine
  • Brother International LB-6800PRW | Users Manual - English - Page 41
    in injuries. Selecting the needle depending on the thread and fabric types The sewing machine needle should be used depends on the fabric and thread thickness. Refer to thread Silk thread Synthetic thread Silk thread Size 60-90 50 60-90 50 30 50 50-60 50-60 50-90 50 50 Size of Needle 75/11-90/14
  • Brother International LB-6800PRW | Users Manual - English - Page 42
    a 90/14 to 100/16 needle, regardless of the fabric or thread. ■ Embroidery needles Use a 75/11 home sewing machine needle. When embroidering on thick fabrics such as denim, use a 90/14 or 100/16 home sewing machine needle. CAUTION z The appropriate fabric, thread and needle combinations are shown in
  • Brother International LB-6800PRW | Users Manual - English - Page 43
    clamp screw • Do not apply a strong force when loosening or tightening the needle clamp screw, otherwise certain parts of the sewing machine may be damaged. Place fabric or paper under the presser foot c and cover the holes on the needle plate. Note z Before replacing the needle, place fabric or
  • Brother International LB-6800PRW | Users Manual - English - Page 44
    GETTING READY While holding the needle with your left hand, g use the screwdriver to tighten the needle clamp screw. Install the twin needle in the same way. CAUTION z Be sure to insert the needle until it touches the needle stopper and securely tighten the needle clamp screw with the screwdriver.
  • Brother International LB-6800PRW | Users Manual - English - Page 45
    feet designed specifically for this sewing machine. Use of any other presser foot may result in injuries or damage to the machine. Replacing the presser foot Replace the presser foot as described below. Memo z For details on attaching the embroidery foot "Q", refer to "Attaching the Embroidery Foot
  • Brother International LB-6800PRW | Users Manual - English - Page 46
    is selected, the icon for the presser foot that should be used appears in the screen. Check that the correct presser foot is attached before starting to sew. If the wrong presser foot is installed, turn off the sewing machine, attach the correct presser foot, and then select the desired stitch again
  • Brother International LB-6800PRW | Users Manual - English - Page 47
    side of the presser bar. embroidery foot, optional free-motion open toe quilting foot "O" and optional walking foot. Use the screwdriver to remove the presser foot holder. CAUTION z Before attaching/removing the presser foot, be sure to turn off the sewing machine. Otherwise, injuries may occur
  • Brother International LB-6800PRW | Users Manual - English - Page 48
    attachment. a a a Flat bed attachment X With the flat bed attachment removed, freearm sewing is possible. Slide the part that you wish to sew onto the b arm, and then sew from the top. a a Arm When you have finished free-arm sewing, c install the flat bed attachment back in its original position. 46
  • Brother International LB-6800PRW | Users Manual - English - Page 49
    2 SEWING BASICS The necessary preparations for sewing are described in this chapter. Sewing...48 Setting the Stitch ...57 Useful Functions...61 Useful Sewing Tips 65
  • Brother International LB-6800PRW | Users Manual - English - Page 50
    power before replacing the presser foot. For details on replacing the presser foot, refer to "Replacing the presser foot" (page 43). ↓ 2 Turn on the machine. Turn on the sewing machine. For details on turning on the machine, refer to "Turning on the machine" (page 17). ↓ 3 Select the stitch
  • Brother International LB-6800PRW | Users Manual - English - Page 51
    should be used appears on the screen. Check that the correct presser foot is attached before starting to sew. If the wrong presser foot is installed, turn off the sewing machine, attach the correct presser foot, and then select the desired stitch again. Memo z For details on setting the automatic
  • Brother International LB-6800PRW | Users Manual - English - Page 52
    SEWING BASICS Positioning the fabric Be sure that the fabric pieces are sewn in the correct order and that the right and wrong sides of the fabric are aligned correctly. Turn on the machine under the presser foot. c Memo z If the seam allowance is positioned on the right side, sewing in a straight
  • Brother International LB-6800PRW | Users Manual - English - Page 53
    Once you are ready to start sewing, you can start the sewing machine. Sewing can be started and stopped using the operation button (Start/stop button) or the foot controller. For details on the foot controller, refer to next page. Memo z When the foot controller is plugged in, (Start/stop button
  • Brother International LB-6800PRW | Users Manual - English - Page 54
    side of the sewing machine. a a a Sewing speed controller X The speed set using the sewing speed controller is the foot controller's maximum sewing speed. Once you are ready to start sewing, slowly e press down on the foot controller. Pressing down on the foot controller increases the sewing speed
  • Brother International LB-6800PRW | Users Manual - English - Page 55
    be used for a long period of time, unplug the foot controller, otherwise a fire or an electric shock may occur. Press (Start/stop button), or press down on b the foot controller. At this time, if (Start/stop button) is held down, the machine sews at a slow speed. • For details, refer to "Starting
  • Brother International LB-6800PRW | Users Manual - English - Page 56
    stop button), or press down on h the foot controller. At this time, if (Start/stop button) is held down, the machine sews at a slow speed. X The machine starts sewing in the normal sewing direction. After sewing to the end of the stitching, the i sewing machine stops. Release (Start/stop button) or
  • Brother International LB-6800PRW | Users Manual - English - Page 57
    (Thread cutter button) if there is no fabric under the presser foot or while the machine is sewing, otherwise damage to the machine may occur. Memo z The machine can be set so that the threads will be cut automatically when sewing is finished. For details, refer to "Automatically cutting the thread
  • Brother International LB-6800PRW | Users Manual - English - Page 58
    you wish to finish the stitching and the a sewing machine is stopped, press (Needle position button) once to raise the needle. a a Needle position button Raise the presser foot lever. b a a Presser foot lever Pull the fabric to the left side of the machine, c and then pass the threads through the
  • Brother International LB-6800PRW | Users Manual - English - Page 59
    Stitch settings return to their defaults if they are changed, when the machine is turned off or a different stitch is selected before the stitch setting the setting to its default. z If the foot controller is connected, the sewing speed controller can be used to adjust the zigzag width. For
  • Brother International LB-6800PRW | Users Manual - English - Page 60
    the stitch width. If the sewing machine is set so that the stitch width can be adjusted using the sewing speed controller, the stitch width can quickly and easily be adjusted. In this case, the sewing speed is adjusted with the foot controller. Connect the foot controller. a • For details, refer to
  • Brother International LB-6800PRW | Users Manual - English - Page 61
    being used. ■ Correct thread tension The upper thread and the bobbin thread should cross near the center of the fabric. Only the upper the stitches are bunched together, increase the stitch length. Continuing to sew with the stitches bunched together may result in the needle bending or breaking
  • Brother International LB-6800PRW | Users Manual - English - Page 62
    may stop sewing if tension is set extremely low. This is not a sign that there is anything wrong with your machine. Simply adjust to the correct stitch tension and begin again. b c d a Wrong side of fabric b Right side of fabric c Upper thread d Bobbin thread e The upper thread is visible from
  • Brother International LB-6800PRW | Users Manual - English - Page 63
    reverse/ reinforcement stitches Position the fabric under the presser foot, and d then press (Start/stop button) once. The sewing machine can be set to automatically sew reverse or reinforcement stitches at the beginning and end of the stitching. Depending on the selected stitch, 2 reverse
  • Brother International LB-6800PRW | Users Manual - English - Page 64
    a Stop the machine and change the sewing direction. b Start the machine again. Automatically cutting the thread The sewing machine can be set is also set. Turn on the machine. a Memo z To turn programmed thread cutting off, press . Position the fabric under the presser foot, and d then press (Start/
  • Brother International LB-6800PRW | Users Manual - English - Page 65
    left and right). has been selected, this operation is unnecessary. X After the reverse stitching or reinforcement Turn on the machine. a stitching has been done, the sewing machine stops, and the thread is cut. 2 X The LCD comes on. Select a stitch. b • For details on selecting a stitch, refer
  • Brother International LB-6800PRW | Users Manual - English - Page 66
    SEWING BASICS Saving stitch settings This machine is preset with the default settings for the stitch . When the same stitch pattern is selected, the last settings saved are displayed even if the machine was turned off. If the settings are changed again and is pressed, or if is pressed
  • Brother International LB-6800PRW | Users Manual - English - Page 67
    direction When the stitching reaches a corner, stop the a sewing machine. Leave the needle lowered (in the fabric). If the needle remained up when the machine stopped sewing, press (Needle position button) to lower the needle. Raise the presser foot lever, and then turn the b fabric. Turn the
  • Brother International LB-6800PRW | Users Manual - English - Page 68
    . a Press the black button (presser foot holding b pin) on the left side of zigzag foot "J". Keep the button held in and lower the presser foot. CAUTION z Use only the ungummed hook-and-loop fastener which is for sewing. If the glue is attached to the needle or the bobbin hook race, it may cause
  • Brother International LB-6800PRW | Users Manual - English - Page 69
    the stretch stitches or the thread for knits gives 2 3 an attractive finishes. 4 5 9 10 34 6 Sewing an even seam allowance To sew an even seam, start sewing so that the seam allowance is to the right of the presser foot, and the edge of the fabric is aligned with either the right edge of
  • Brother International LB-6800PRW | Users Manual - English - Page 70
    SEWING BASICS 68
  • Brother International LB-6800PRW | Users Manual - English - Page 71
    Chart 70 Overcasting Stitches 74 Basic Stitching ...78 Blind Hem Stitching 80 Buttonhole Stitching 83 Zipper Insertion...90 Sewing Stretch Fabrics and Elastic Tape 95 Appliqué, Patchwork and Quilt Stitching 97 Reinforcement Stitching 103 Eyelet Stitching...108 Decorative Stitching 109
  • Brother International LB-6800PRW | Users Manual - English - Page 72
    Needle Walking Foot Presser Foot Stitch Name Pattern Application Stitch Width [mm (inch)] Auto Manual 1 J Basic stitching, sewing gathers Overcasting and attaching appliqués 3.5 0.0-7.0 1.4 0.0-4.0 Yes (1/8) (0-1/4) (1/16) (0-3/16) (J) Reverse No 8 J Beginning sewing from the right
  • Brother International LB-6800PRW | Users Manual - English - Page 73
    foot) Straight stitch that 23 looks hand-sewn (for quilting) J Straight stitch quilting that looks hand-sewn 0.0 (0) 0.0-7.0 (0-1/4) 2.5 (3/32) 1.0-4.0 (1/16-3/16) No Reinforcement No Zigzag stitch 24 (for quilting) J Appliqué quilting, free J stitching and sewing overcasting on both
  • Brother International LB-6800PRW | Users Manual - English - Page 74
    Foot Twin Needle Walking Foot Stitch Name Pattern Application 35 J Decorative stitching Stitch Width [mm (inch)] Auto 4.0 (3/16) Manual 0.0-7.0 (0-1/4) Stitch Length [mm (inch)] Auto Manual ) (1/64-3/16) (J) Reinforcement No 39 Lace sewing, decorative N hemming, heirloom stitching, etc.
  • Brother International LB-6800PRW | Users Manual - English - Page 75
    Foot Stitch Name Pattern Application 48 A Horizontal buttonholes on thin and mediumweight fabrics Stitch Width [mm (inch)] Stitch Length [mm (inch)] Auto Manual Auto Manual 58 Darning stitch 59 60 Bar tack stitch 61 Button-sewing stitch 62 Eyelet stitch 63 A Darning mediumweight fabrics
  • Brother International LB-6800PRW | Users Manual - English - Page 76
    Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual Presser Foot 3.5 2.0 (1/8) (1/16) 2.5-5.0 machine starts sewing. Attach overcasting foot "G". a G Position the fabric with the edge of the fabric c against the guide of the presser foot, and then lower the presser foot
  • Brother International LB-6800PRW | Users Manual - English - Page 77
    16) CAUTION ● Be sure to turn off the main power before replacing the pressor foot. Otherwise, injuries may occur if (Start/stop button) is accidentally pressed and the machine starts sewing. Attach zigzag foot "J". a J Sew along the edge of the fabric with the c needle dropping off the edge at
  • Brother International LB-6800PRW | Users Manual - English - Page 78
    /stop button) is accidentally pressed and the machine starts sewing. Position the side cutter so that side cutter pin c is aligned with the notch in the presser foot holder, and then slowly lower the presser foot lever. Note z Thread the needle manually when using the side cutter, or only attach
  • Brother International LB-6800PRW | Users Manual - English - Page 79
    Raise the presser foot lever to check that the d side cutter is securely attached. Pass the upper thread under the side cutter, e and then pull it out toward the rear of the sewing machine. Position the fabric in the side cutter. h The cut in the fabric should be positioned over the guide plate of
  • Brother International LB-6800PRW | Users Manual - English - Page 80
    inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual - - Presser Foot 1 Straight stitch Basic stitching and sewing gathers or and the machine starts sewing. Basting Attach zigzag foot "J". a • For details on replacing the presser foot, refer to "Replacing the presser foot" (page 43
  • Brother International LB-6800PRW | Users Manual - English - Page 81
    is changed (between 0 and 7.0 mm (1/4 inch)), the needle position will also change. By changing the stitch width and sewing with the right side of the presser foot aligned with the edge of the fabric, a seam allowance can be sewn with a fixed width. 0.0 2.0 5.5 7.0 a Stitch width setting
  • Brother International LB-6800PRW | Users Manual - English - Page 82
    to turn off the main power before replacing the pressor foot. Otherwise, injuries may occur if (Start/stop button) is accidentally pressed and the machine starts sewing. Sew a blind hem according to the following procedure. Memo z When the size of cylindrical pieces is too small to slide onto the
  • Brother International LB-6800PRW | Users Manual - English - Page 83
    h free-arm sewing possible. • For details on free-arm sewing, refer to "Freearm sewing" (page 46). Slide the part that you wish to sew onto the against the guide of the presser foot, and then lower the presser foot lever. R 1 b c a Wrong side of fabric b Fold of hem c Guide Adjust the stitch
  • Brother International LB-6800PRW | Users Manual - English - Page 84
    . 1 2 a Wrong side of fabric b Right side of fabric Memo z For details, refer to "Adjusting the stitch width" (page 57). Sew with the fold of the hem against the l presser foot guide. Remove the basting stitching and reverse the m fabric. 1 2 a Wrong side of fabric b Right side of fabric 82
  • Brother International LB-6800PRW | Users Manual - English - Page 85
    stitches are available for sewing one-step buttonholes, one for sewing on buttons. Stitch Name Pattern Application 48 Horizontal buttonholes on thin and mediumweight fabrics Stitch Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual Presser Foot 49 Horizontal buttonholes on
  • Brother International LB-6800PRW | Users Manual - English - Page 86
    pressed and the machine starts sewing. The names of parts of buttonhole foot "A", which is used for sewing buttonholes, are indicated below. Use chalk to mark on the fabric the position a and length of the buttonhole. 1 2 5 6 3 4 A a Button guide plate b Presser foot scale c Pin d Marks
  • Brother International LB-6800PRW | Users Manual - English - Page 87
    the diameter and thickness of the button, and then set the button guide plate to the calculated length. (The distance between the markings on the presser foot scale is 5 mm (3/16 3 inch).) a b c a Presser foot scale b Length of buttonhole (diameter + thickness of button) c 5 mm (3/16 inch
  • Brother International LB-6800PRW | Users Manual - English - Page 88
    lever The buttonhole lever is positioned behind the bracket on the buttonhole foot. a a a Seam ripper For keyhole buttonholes, use the eyelet punch g your left hand, and then start sewing. X Once sewing is completed, the machine automatically sews reinforcement stitches, then stops. 86 a
  • Brother International LB-6800PRW | Users Manual - English - Page 89
    the seam ripper in any other way than how it is intended. ■ Sewing buttonholes on stretch fabrics When sewing buttonholes on stretch fabrics, use a gimp thread. Hook the gimp thread onto the part of a buttonhole foot "A" shown in the illustration. ■ Changing the density of the stitching Adjust the
  • Brother International LB-6800PRW | Users Manual - English - Page 90
    and lower the presser foot lever. Raise the presser foot lever, and then slide the b drop feed lever, located at the rear of the machine on the base, to the needle goes into the two holes toward the rear of the sewing machine, and then sew them in the same way. Turn the handwheel toward you g (
  • Brother International LB-6800PRW | Users Manual - English - Page 91
    Start sewing. h Set the sewing speed controller to the left (so that the speed will be slow). X The sewing machine automatically stops after sewing reinforcement stitches. Note z Do not press (Thread cutter button). 3 Pull the upper thread at the end of the i stitching to the wrong side of
  • Brother International LB-6800PRW | Users Manual - English - Page 92
    (inch)] Auto Manual Presser Foot 3.5 0.0-7.0 2.5 0.2-5.0 (1/8) (0-1/4) (3/32) (1/64-3/16) I CAUTION ● Be sure to turn off the main power before replacing the pressor foot. Otherwise, injuries may occur if (Start/stop button) is accidentally pressed and the machine starts sewing. There are many
  • Brother International LB-6800PRW | Users Manual - English - Page 93
    on the right side b Needle drop point • For details on replacing the presser foot, refer to "Replacing the presser foot" (page 43). a Stitching b Right side of fabric c Basting stitching d End of zipper opening CAUTION ● When sewing, be sure that the needle does not touch the zipper, otherwise the
  • Brother International LB-6800PRW | Users Manual - English - Page 94
    will describe how to stitch on the left side, as shown in the illustration. Attach zigzag foot "J". a J • For details on replacing the presser foot, refer to "Replacing the presser foot" (page 43). Sew straight stitches up to the zipper opening. b With the right sides of the fabric facing each
  • Brother International LB-6800PRW | Users Manual - English - Page 95
    5 cm (2 inches) from the j end of the zipper, stop the sewing machine with the needle lowered (in the fabric), and then raise the presser foot lever. Open the zipper and continue sewing. k CAUTION ● When using zipper foot "I", be sure to select the straight stitch (center needle position), and
  • Brother International LB-6800PRW | Users Manual - English - Page 96
    not touch the zipper, otherwise the needle may bend or break. When you are about 5 cm (2 inches) from the o end of the zipper, stop the sewing machine with the needle lowered (in the fabric), and then raise the presser foot lever. Remove the basting stitching, open the zipper, p and then continue
  • Brother International LB-6800PRW | Users Manual - English - Page 97
    Width [mm (inch)] Auto Manual 0.0 0.0-7.0 (0) (0-1/4) Stitch Length [mm (inch)] Auto Manual Presser Foot 2.5 1.5-4.0 (3/32) (1/16 foot. Otherwise, injuries may occur if (Start/stop button) is accidentally pressed and the machine starts sewing. Stretch stitching Attach zigzag foot "J". a J Sew
  • Brother International LB-6800PRW | Users Manual - English - Page 98
    right hand. 1 2 a Elastic tape b Pin Attach zigzag foot "J". b J • For details on replacing the presser foot, refer to "Replacing the presser foot" (page 43). Select a stitch. c • For details, refer to "Selecting stitching" (page 49). CAUTION ● When sewing, be sure that the needle does not touch
  • Brother International LB-6800PRW | Users Manual - English - Page 99
    appliqués (center baseline/reverse stitching) Appliqué quilting, free-motion quilting, satin stitching Stitch Width [mm (inch)] Auto Manual 0.0-7.0 3.5 (0-1/4) (1/8) Stitch Length [mm (inch)] Auto Manual 1.4 0.0-4.0 (1/16) (0-3/16) Presser Foot 19 Appliqué stitch 25 Attaching appliqu
  • Brother International LB-6800PRW | Users Manual - English - Page 100
    . 1 a Basting stitching Attach zigzag foot "J". d J • For details on replacing the presser foot, refer to "Replacing the presser foot" (page 43). When sewing around corners, stop the machine with the needle in the fabric just outside of the appliqué, raise the presser foot lever, and then turn the
  • Brother International LB-6800PRW | Users Manual - English - Page 101
    the presser foot with the edge of the fabric, and sew using stitch 21 . 1 Piecing Sewing together zigzag foot "J". b J • For details on replacing the presser foot, refer to "Replacing the presser foot" the left side of the presser foot with the edge of the fabric, and sew using stitch 22 . 1 a
  • Brother International LB-6800PRW | Users Manual - English - Page 102
    , and then tighten the screw with the screwdriver. a Walking foot Quilting guide Note z When sewing with the walking foot, sew at a speed between slow and medium. z When quilting, use a 90/14 home sewing machine needle. z The walking foot can only be used with straight or zigzag stitch patterns
  • Brother International LB-6800PRW | Users Manual - English - Page 103
    Insert the stem of the quilting guide into the a hole at the rear of the walking foot or presser foot holder. † Walking foot 3 † Presser foot holder Adjust the stem of the quilting guide so that b the guide aligns with the seam that has already been sewn. Appliqué, Patchwork and Quilt Stitching 101
  • Brother International LB-6800PRW | Users Manual - English - Page 104
    free-motion quilting foot "O" by b positioning the pin of the quilting foot above the needle clamp screw and aligning the lower-left of the quilting foot and the presser bar. 1 3 2 a a Drop feed lever (as seen from the rear of the machine) X The feed dogs are lowered. Turn on the sewing machine
  • Brother International LB-6800PRW | Users Manual - English - Page 105
    Stitch Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual Presser Foot Triple stretch 4 stitch Reinforcing the seams replacing the pressor foot. Otherwise, injuries may occur if (Start/stop button) is accidentally pressed and the machine starts sewing. Triple stretch
  • Brother International LB-6800PRW | Users Manual - English - Page 106
    do not push in the front of the presser foot, otherwise the bar tack will not be sewn with the correct size. Attach buttonhole foot "A". b • For details on replacing the presser foot, refer to "Replacing the presser foot" (page 43). Select stitch 60 . c • For details, refer to "Selecting stitching
  • Brother International LB-6800PRW | Users Manual - English - Page 107
    Gently hold the end of the upper thread in f your left hand, and then start sewing. X Once sewing is completed, the sewing machine automatically sews reinforcement stitches, then stops. Raise the presser foot lever, remove the fabric, g and then cut the threads. Raise the buttonhole lever to its
  • Brother International LB-6800PRW | Users Manual - English - Page 108
    shown below. a a Reinforcement stitching Determine the desired length of the darning. a Set the button guide plate on buttonhole foot "A" to the desired length. (The distance between the markings on the presser foot scale is 5 mm (3/16 inch).) a Select stitch 58 or 59 . c • For details, refer to
  • Brother International LB-6800PRW | Users Manual - English - Page 109
    foot, otherwise the darning will not be sewn with the correct size. Gently hold the end of the upper thread in f your left hand, and then start sewing. a a Do not reduce the gap. Pull down the buttonhole lever as far as e possible. X Once sewing is completed, the sewing machine automatically sews
  • Brother International LB-6800PRW | Users Manual - English - Page 110
    (inch)] Auto Manual 7.0, 6.0 or 7.0 5.0 (1/4) (1/4, 15/64 or 3/16) Presser Foot N CAUTION ● Be sure to turn off the main power before replacing the pressor foot. Otherwise, injuries may occur if (Start/stop button) is accidentally pressed and the machine starts sewing. Attach monogramming
  • Brother International LB-6800PRW | Users Manual - English - Page 111
    Sewing two pieces of fabric together across an open seam Stitch Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual Presser Foot 2.5-7.0 (3/25-1/4) 0.5 0.1-1.0 (1/32) (1/64-3/16) 39 3.5 Lace sewing, decorative (1/8) hemming, heirloom stitching, 40 etc. 6.0 (15/64)
  • Brother International LB-6800PRW | Users Manual - English - Page 112
    stitching Stitch Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual Presser Foot 6.0 (15/64) 1.5-7.0 1.6 1.0-4.0 5.0 replacing the pressor foot. Otherwise, injuries may occur if (Start/stop button) is accidentally pressed and the machine starts sewing. Fagoting Stitching
  • Brother International LB-6800PRW | Users Manual - English - Page 113
    on the collars of blouses and to decorate the edges of projects. Attach monogramming foot "N". a After sewing is finished, remove the paper. g • For details on replacing the presser foot, refer to "Replacing the presser foot" (page 43). Select stitch 27 . 3 b • For details, refer to "Selecting
  • Brother International LB-6800PRW | Users Manual - English - Page 114
    on replacing the presser foot, refer to "Replacing the presser foot" (page 43). Select the straight stitch, and then adjust the b stitch length to 4.0 mm (3/16 inch) and loosen the thread tension. • Pull up the bobbin thread. For details, refer to "When pulling up the bobbin thread may be necessary
  • Brother International LB-6800PRW | Users Manual - English - Page 115
    3 b J • For details, refer to "Replacing the presser foot" (page 43). Select stitch 20 , and then increase the c thread tension. • For details, refer to "Selecting stitching" (page 49) and "Adjusting the thread tension" (page 59). Sew while making sure that the needle drops d slightly off the
  • Brother International LB-6800PRW | Users Manual - English - Page 116
    wing needle, otherwise the sewing machine may be damaged. Manually pass the thread through the eye of the needle from the front to the back. For details, refer to "Threading the needle manually (without using the needle threader)" (page 36). Attach monogramming foot "N". b • For details on replacing
  • Brother International LB-6800PRW | Users Manual - English - Page 117
    with the wing needle, select a stitch width of 6.0 mm (15/64 inch) or less. Start sewing. d Attach monogramming foot "N". b CAUTION ● When sewing with the wing needle, select a stitch width of 6.0 mm (15/64 inch) or less, otherwise the needle may bend or break. ● After adjusting the stitch
  • Brother International LB-6800PRW | Users Manual - English - Page 118
    key back to OFF. 1 a 4 mm (3/16 inch) Attach monogramming foot "N" . b • For details on replacing the presser foot, refer to "Replacing the presser foot" (page 43). Select stitch 42 . c • For details, refer to "Selecting stitching" (page 49). Sew along the center of the unfrayed section. d N 116
  • Brother International LB-6800PRW | Users Manual - English - Page 119
    steps for embroidering are described in this chapter. Embroidering Neatly 118 Attaching the Embroidery Foot 120 Attaching the Embroidery Unit 123 Preparing the Fabric 126 Attaching the Embroidery Frame 130 Selecting Embroidery Patterns 132 Embroidering...139 Editing and Saving Patterns 143
  • Brother International LB-6800PRW | Users Manual - English - Page 120
    cause the pattern to sew incorrectly. For the bobbin thread, use the embroidery bobbin thread. For details, refer to "Optional accessories" (page 9). Memo z For good quality embroidery designs be sure to use embroidery thread designed for embroidery machines. z Before starting to sew, be sure there
  • Brother International LB-6800PRW | Users Manual - English - Page 121
    thread and set it in place. For details on setting up the bobbin thread, refer to "Winding/Installing the Bobbin" (page 22). 5 Fabric preparation ↓ 4 Attach a stabilizer material to the fabric, and hoop it in an embroidery frame. For details on preparing the fabric, refer to "Preparing the
  • Brother International LB-6800PRW | Users Manual - English - Page 122
    Attaching the Embroidery Foot This section describes how to attach the embroidery foot "Q". Attaching the embroidery foot Attach the embroidery foot "Q" when embroidering. Have the included embroidery foot "Q" and a screwdriver ready. Turn off the sewing machine. b a b a Embroidery foot bar
  • Brother International LB-6800PRW | Users Manual - English - Page 123
    the presser foot and break or bend. ● Before sewing, always turn the handwheel toward you (counterclockwise) slowly to make sure that the needle does not hit the presser foot. The needle may break or bend. a Presser bar b Needle clamp screw c Embroidery foot bar Attaching the Embroidery Foot 121
  • Brother International LB-6800PRW | Users Manual - English - Page 124
    at the back of the d embroidery foot with your finger, loosen the presser foot holder screw, and then remove embroidery foot "Q". Turn the screwdriver toward the back. a a Needle position button Turn off the sewing machine. b a Screwdriver Attach the presser foot holder. e • For details, refer to
  • Brother International LB-6800PRW | Users Manual - English - Page 125
    Unit This section describes how to attach the embroidery unit. Embroidery unit precautions Attaching the embroidery unit CAUTION ● Do not move the sewing machine with the embroidery unit in place. The embroidery unit may be dropped and cause injury. ● Keep your hands and other objects away
  • Brother International LB-6800PRW | Users Manual - English - Page 126
    insert the connector into the connection port. z Do not push on the carriage when attaching the embroidery unit to the machine, otherwise damage to the embroidery unit may result. Turn on the sewing machine. d a Carriage CAUTION ● Do not put your hands or other objects near the carriage. It may
  • Brother International LB-6800PRW | Users Manual - English - Page 127
    unit Make sure that the sewing machine is completely stopped and follow the instructions below. Remove the embroidery frame. a • For details on removing the embroidery frame, refer to "Removing the embroidery frame" (page 131). Press , and then press . b Hold the release button on the
  • Brother International LB-6800PRW | Users Manual - English - Page 128
    to prevent poor quality embroidery designs. Memo z We recommend the optional stabilizer material for embroidery. Use a water soluble sheet on thin materials like organdy and fabrics with a nap like towels. To obtain optional accessories or parts, visit [http://www.brother.com/], or [http:// www
  • Brother International LB-6800PRW | Users Manual - English - Page 129
    frame. Tighten the adjustment screw by hand just d enough to secure the fabric. CAUTION ● Use the embroidery frame that matches the size of the pattern being embroidered. Otherwise, the embroidery frame may be hit by the presser foot and cause injury or needle breakage. Preparing the Fabric 127
  • Brother International LB-6800PRW | Users Manual - English - Page 130
    (right side) d Stabilizer material e Ledge of outer frame • Press down firmly until the inner frame is securely pressed against the ledge of the outer frame. Embroidery sheet (large) [option] Make a mark with a chalk pen at the center of a the position for the pattern to be embroidered
  • Brother International LB-6800PRW | Users Manual - English - Page 131
    thin pieces like ribbon are being embroidered, use stabilizer material as a base to stretch on the frame. We recommend stabilizer material for all embroidery. a b c a b a Base line b Mark Place the inner frame with the fabric on the d outer frame and stretch the fabric. • For details, refer to page
  • Brother International LB-6800PRW | Users Manual - English - Page 132
    correctly. CAUTION ● Correctly set the embroidery frame into the embroidery frame holder. Otherwise, the presser foot may hit the embroidery frame, resulting in injury. CAUTION ● Do not touch a button. If a button is accidentally pressed, the machine starts sewing, and your finger may be pricked
  • Brother International LB-6800PRW | Users Manual - English - Page 133
    Removing the embroidery frame Pass the embroidery frame under the presser d foot while raising the presser foot lever even further. Make sure that the sewing machine is completely stopped and follow the instructions below. Raise the presser foot lever. a a a Presser foot lever Press (Needle
  • Brother International LB-6800PRW | Users Manual - English - Page 134
    pattern. Copyright information The patterns saved in the sewing machine and embroidery cards are intended for private use only. Any public changing the upper thread according to the instructions displayed on the screen. For details, refer to "Selecting an embroidery pattern" (page 137). b Character
  • Brother International LB-6800PRW | Users Manual - English - Page 135
    to adjust language or change the thread color display or other settings. e Press to get help on embroidery unit attachment, embroidery frame attachment, etc. f Press this key to save embroidery patterns and the alphabet characters in the machine's memory. Selecting Embroidery Patterns 133
  • Brother International LB-6800PRW | Users Manual - English - Page 136
    ) THREAD# is selected.) •EMBROIDERY (POLYESTER) THREAD# •COUNTRY (COTTON) THREAD# •MADEIRA POLY THREAD# •MADEIRA RAYON THREAD# •SULKY THREAD# •ROBISON-ANTON POLY THREAD# When a specific pattern is selected, press this key and then, press to switch the display. The sewing settings such as the
  • Brother International LB-6800PRW | Users Manual - English - Page 137
    refer to "Adjusting the layout and the size" (page 143). 4 Press this key when you want to change the color, character by character in character embroidery. Since the sewing machine stops at the end of each character, the upper thread is changed as you sew. Press this key again to cancel multicolor
  • Brother International LB-6800PRW | Users Manual - English - Page 138
    When "The pattern is too large for the embroidery frame" is displayed, no more characters can be input. z Characters from different fonts (sans serif and serif, etc.) cannot be combined. Select the alphabet characters. a Select the font. b Enter the characters. c Memo z If a character is pressed
  • Brother International LB-6800PRW | Users Manual - English - Page 139
    in the machine's memory. 70 Embroidery patterns Memo z Refer to "Embroidery Pattern Color Change Table" in the Quick reference guide for samples 12 stitch types. Memo z Refer to "Frame patterns" in the Quick reference guide for frame pattern shapes and stitches. Press . a 4 X The pattern
  • Brother International LB-6800PRW | Users Manual - English - Page 140
    using (Previous page key) and (Next page key), and select from the 12 stitches. Insert the embroidery card in the embroidery b card slot on the right side of the sewing machine. Face the arrow on the embroidery card toward you, and insert it in the direction of the arrow. X When a stitch is
  • Brother International LB-6800PRW | Users Manual - English - Page 141
    shown a on the screen. c a b d e Set the embroidery thread, and thread the b needle. 4 a Embroidery frames that can be used for embroidering b Current color step/Number of colors in design c Current name of color d Current color part e Next color part • Refer to "Threading the upper thread
  • Brother International LB-6800PRW | Users Manual - English - Page 142
    button CAUTION ● Use the embroidery frame that matches the size of the pattern being embroidered. Otherwise, the embroidery frame may be hit by the presser foot and cause injury or needle breakage. After progressing 5-6 stitches, press f (Start/stop button) to stop the machine. Use scissors to cut
  • Brother International LB-6800PRW | Users Manual - English - Page 143
    lever, and press g (Start/stop button). embroidery frame. 4 Lower the presser foot lever, and press c (Start/stop button). X The cut-out for the appliqué piece is sewn, and the sewing machine stops. a b a Cut-out line b Appliqué piece fabric X "APPLIQUE POSITION" will be displayed on the screen
  • Brother International LB-6800PRW | Users Manual - English - Page 144
    EMBROIDERY Apply a thin layer of fabric glue or spray h adhesive to the back of the appliqué piece, and attach it in the appliqué position. Lower the presser foot lever, and press i (Start/stop button). X The position for the appliqué is stitched, and the sewing machine stops. Memo z When "APPLIQUE
  • Brother International LB-6800PRW | Users Manual - English - Page 145
    key/Layout key f Rotation key g Horizontal mirror image key 4 X The sewing screen is displayed. h Trial key i Starting point key j Distance from the center k Embroidery size Press . b Embroidery frame size The size of embroidery frame that can be used is displayed. When the smaller mark is
  • Brother International LB-6800PRW | Users Manual - English - Page 146
    of the pattern or reverse it, the embroidery which have been moved will return to its initial position. Use the Change position keys after you have changed the size of the pattern or reversed it. z You can save patterns you have changed the size and position in the machine's memory. Refer to "Saving
  • Brother International LB-6800PRW | Users Manual - English - Page 147
    setting. z You can also check the pattern size and increase the upper thread tension. distance from the center by pressing after beginning embroidering. z The embroidery patterns you have edited or adjusted can be saved in the sewing machine's memory. For details, refer to a b a Right side
  • Brother International LB-6800PRW | Users Manual - English - Page 148
    point is set to lower left of the design. Lower the presser foot, and then press g (Start/stop switch) to begin sewing. When embroidering is finished, trim the thread h leaving the end of the thread longer than usual. Then reset the fabric in the embroidery frame, in a position where you can
  • Brother International LB-6800PRW | Users Manual - English - Page 149
    Embroidery end position Lower the presser foot, and then press m (Start/Stop button) to embroider "DEF". Resewing When the wrong upper thread color has been sewn, it can be resewn with the correct color. Press (Start/stop button) to stop the a sewing machine design. Editing and Saving Patterns 147
  • Brother International LB-6800PRW | Users Manual - English - Page 150
    Thread runs out partway through a design When the upper thread or the bobbin thread runs out while sewing, the sewing machine stops. Move the needle back about 10 stitches and resume sewing. Memo z When the bobbin thread runs out, cut the threads and remove the embroidery frame before replacing the
  • Brother International LB-6800PRW | Users Manual - English - Page 151
    pressed continuously, it moves forward 1 -> 9 ->30 stitches. 4 Turn on the sewing machine, and then select f the pattern. Memo z If you have changed the embroidery size and/or layout before turning off the machine, make the same setting changes again before restarting embroidering. For details
  • Brother International LB-6800PRW | Users Manual - English - Page 152
    patterns and the alphabet characters you have customized can be saved in the sewing machine's memory. Since the saved patterns will not be erased when the power is turned off, you can always retrieve them for embroidery. This is convenient for saving names and the like. You can save up to 12
  • Brother International LB-6800PRW | Users Manual - English - Page 153
    5 APPENDIX The various maintenance and troubleshooting procedures are described in this chapter. Care and Maintenance 152 Troubleshooting ...154 Index ...165
  • Brother International LB-6800PRW | Users Manual - English - Page 154
    foot holder b Presser foot holder screw c Needle clamp screw Cleaning the race Sewing performance will suffer if dust collects in the bobbin case. Therefore, it should be cleaned periodically. Grasp both sides of the needle plate cover, and e then slide it toward you. Turn off the sewing machine
  • Brother International LB-6800PRW | Users Manual - English - Page 155
    may break or sewing performance may suffer. For a new bobbin case (part code: XC3152-221 (green marking)), contact your nearest authorized service center. ● Be sure that the bobbin case is correctly installed, otherwise the needle may break. a 5 b c c b a Bobbin case b Projection c Spring Memo
  • Brother International LB-6800PRW | Users Manual - English - Page 156
    problem persists, contact your dealer or the nearest authorized service center. Symptom Probable Cause Remedy The machine is not turned on. Turn on the machine. The start/stop button was not pressed. Press the start/stop button. The sewing machine does not operate. The presser foot lever
  • Brother International LB-6800PRW | Users Manual - English - Page 157
    dealer or the nearest authorized service center. - A bobbin designed specifically for this machine is not used. Incorrect bobbins will not work properly. Only use a bobbin designed specifically for this machine. page 22 Bobbin thread does not wind neatly on the bobbin. The thread is not passed
  • Brother International LB-6800PRW | Users Manual - English - Page 158
    foot holder. The thread tension is incorrect. Adjust the tension of the upper thread. A bobbin designed specifically for this machine is not used. Incorrect bobbins will not work properly. Only use a bobbin designed specifically for this machine. The upper thread is The bobbin or sew with stitch
  • Brother International LB-6800PRW | Users Manual - English - Page 159
    made while sewing. The upper thread was not threaded correctly. The bobbin case is scratched, or has a burr on it. Correct the upper threading. Replace the bobbin case. Contact your dealer or the nearest authorized service center. page 32 - A bobbin designed specifically for this machine is not
  • Brother International LB-6800PRW | Users Manual - English - Page 160
    and the fabric is hanging off the table. If embroidery is done with the fabric hanging off the table, the embroidery unit movement will be impaired. Support the fabric while embroidering. The fabric is catching. It is pinched. Stop the sewing machine and set the fabric up correctly. The carriage
  • Brother International LB-6800PRW | Users Manual - English - Page 161
    may be wrong or the needle may break and cause injury. 6 The machine is deleting a previously saved pattern while in embroidery edit mode. The start/stop button was pressed while the foot controller was 7 connected. You tried to use the foot controller for embroidery. Troubleshooting 159
  • Brother International LB-6800PRW | Users Manual - English - Page 162
    pressing the manual memory key. You tried to select an embroidery pattern or change the layout when 15 the needle was down. The machine is turned on while the needle is lowered and the embroidery unit is attached. 16 You tried to initialize the embroidery unit with the embroidery foot lowered
  • Brother International LB-6800PRW | Users Manual - English - Page 163
    the frame. The upper thread has become tangled around the bobbin case, and the 24 needle is bent and hitting the needle plate, etc., so the sewing machine stops (refer to page 154). 25 You tried to use a function that cannot be used when the embroidery unit is attached. Troubleshooting 161
  • Brother International LB-6800PRW | Users Manual - English - Page 164
    Probable Cause An Embroidery Memory Card that may not compatible with your machine has been inserted. • Certain licensed designs cannot be read by this machine. 26 • Designs in an unacceptable card format cannot be read by this machine. • Design data saved in a hoop size not compatible with
  • Brother International LB-6800PRW | Users Manual - English - Page 165
    setting can be changed so that the machine does not beep. Turn on the sewing machine. a 5 X The LCD comes on. Press b panel. (Setting key) in the operation Turn off the sewing machine, then turn it on d again. X The setting screen appears. Press c (Next page key) twice. Troubleshooting 163
  • Brother International LB-6800PRW | Users Manual - English - Page 166
    APPENDIX Press OFF for the buzzer. d X The screen for changing the beep setting appears. Press e (Back key). X The initial stitch screen appears again. 164
  • Brother International LB-6800PRW | Users Manual - English - Page 167
    bed attachment 10 foot controller 9, 52 changing sewing direction 65 foot controller jack 11 checking needle 40 frame pattern selection 137 cleaning bobbin case 152 fraying, preventing 74 cleaning brush 9 free-arm sewing 46 cleaning machine surface 152 free-motion quilting 102
  • Brother International LB-6800PRW | Users Manual - English - Page 168
    9 securing stitching 53 selecting alphabet characters 136 selecting embroidery patterns 132 selecting stitches 49 selecting the needle 39 settings key 13 sewing basics 48 sewing direction change 65 sewing machine help key 13 sewing speed controller 12 shell tuck stitch 113 side cutter 76
  • Brother International LB-6800PRW | Users Manual - English - Page 169
    59, 145 threading 31 threading bobbin 22 5 threading needle 31 threading needle manually 36 tips 65 touch panel 13 trial sewing 65 triple stretch stitch 78, 95, 103 troubleshooting 154 turning machine on/off 16 twin needle 9 twin needle sewing 36 U upper thread 31 upper
  • Brother International LB-6800PRW | Users Manual - English - Page 170
  • Brother International LB-6800PRW | Users Manual - English - Page 171
  • Brother International LB-6800PRW | Users Manual - English - Page 172
    English XE3116-201c Printed in China
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
Product Code
885-V31/V32/V33
GETTING READY
SEWING BASICS
UTILITY STITCHES
EMBROIDERY
APPENDIX
Please visit us at
where you can get product support and answers to
frequently asked questions (FAQs).
Computerized Embroidery and Sewing Machine
Operation Manual