Brother International LB6800THRD Users Manual - English
Brother International LB6800THRD Manual
 |
View all Brother International LB6800THRD manuals
Add to My Manuals
Save this manual to your list of manuals |
Brother International LB6800THRD manual content summary:
- Brother International LB6800THRD | Users Manual - English - Page 1
Computerized Embroidery and Sewing Machine Operation Manual Product Code 885-V31/V32/V33 GETTING READY SEWING BASICS UTILITY STITCHES EMBROIDERY APPENDIX Please visit us at http://solutions.brother.com where you can get product support and answers to frequently asked questions (FAQs). - Brother International LB6800THRD | Users Manual - English - Page 2
- Brother International LB6800THRD | Users Manual - English - Page 3
Thank you for purchasing this embroidery and sewing machine. Before using this machine, carefully read the "Important Safety Instructions", and then study this manual for the correct operation of the various functions. In addition, after you have finished reading this manual, store it where it can - Brother International LB6800THRD | Users Manual - English - Page 4
follow the troubleshooting table in the back of the operation manual to inspect and adjust the machine yourself. If the problem persists, please consult your local authorized Brother dealer. Use this machine only for its intended use as described in the manual. Use accessories recommended by the - Brother International LB6800THRD | Users Manual - English - Page 5
the plug supplied with this equipment, you should contact your authorized dealer to obtain the correct lead. FOR USERS IN AUSTRALIA AND NEW ZEALAND This sewing machine is not intended to be used by young children, and assistance may be required if used by a person with a disability. 3 - Brother International LB6800THRD | Users Manual - English - Page 6
Contents Introduction ...1 Important Safety Instructions 1 Machine Features ...7 Accessories ...8 Included accessories ...8 Optional accessories ...9 Names of Machine Parts and Their Functions 10 Front view...10 Needle and presser foot section ...11 Right-side/rear view ...11 Operation - Brother International LB6800THRD | Users Manual - English - Page 7
the thread ...62 Mirroring stitches ...63 Saving stitch settings ...64 Useful Sewing Tips ...65 Trial sewing ...65 Changing the sewing direction ...65 Sewing curves ...65 Sewing thick fabrics ...65 Sewing hook-and-loop fastener ...66 Sewing thin fabrics...66 Sewing stretch fabrics ...67 Sewing an - Brother International LB6800THRD | Users Manual - English - Page 8
the embroidery foot ...122 Attaching the Embroidery Unit 123 Embroidery unit precautions ...123 Attaching the embroidery unit ...123 Removing the embroidery unit ...125 Preparing the Fabric ...126 Attaching a stabilizer material to the fabric 126 Setting the fabric in the embroidery frame ...127 - Brother International LB6800THRD | Users Manual - English - Page 9
is ready to sew. A red or orange light indicates an error or that the machine is warming up (page 12). h Easy-to-use needle threader You can thread the needle easily by one press of a lever (page 32). i Embroidery You can embroider built-in embroidery patterns, characters, framed decorations, and - Brother International LB6800THRD | Users Manual - English - Page 10
. If any item is missing or damaged, contact your dealer. Included accessories Note z Foot controller: Model T This foot controller can be used on the machine with product code 885-V31/V32/V33.The product code is mentioned on the machine rating plate. z The securing screw on the side of the presser - Brother International LB6800THRD | Users Manual - English - Page 11
021 22 Scissors 23 Disc-shaped screwdriver 24 Embroidery foot "Q" Embroidery set (medium) 25 H 10 cm X W 10 cm (H 4 inches X W 4 inches) 26 Embroidery bobbin thread (white) 27 Accessory bag 28 Soft cover 29 Operation manual 30 Quick reference guide 13 Eyelet punch 135793-001 31 CD 14 - Brother International LB6800THRD | Users Manual - English - Page 12
below. Before using the sewing machine, carefully read these descriptions to learn the names of the machine parts. Front view a Thread guide cover (page 24, 33) Pass the thread under this thread guide cover when winding the bobbin thread and threading the machine. b Thread guide (page 24, 33) Pass - Brother International LB6800THRD | Users Manual - English - Page 13
applies pressure consistently on the fabric as the sewing takes place. Attach the appropriate presser foot for the selected stitching. i Presser foot holder (page 45) The presser foot is installed onto the presser foot holder. a Handle Carry the sewing machine by its handle when transporting the - Brother International LB6800THRD | Users Manual - English - Page 14
changes color according to the machine's operation mode. Green: Red: Orange: The machine is ready to sew or is sewing. The machine can not sew. The machine is winding the bobbin thread, or the bobbin winder shaft is moved to the right side. Memo z When the foot controller is plugged in, (Start - Brother International LB6800THRD | Users Manual - English - Page 15
and more. i Sewing machine help key Press to get help on using the sewing machine. Displays simple explanations of setting upper thread / bobbin winding / setting bobbin thread / needle replacement / embroidery unit attachment / embroidery frame attachment / embroidery foot attachment / presser foot - Brother International LB6800THRD | Users Manual - English - Page 16
14 - Brother International LB6800THRD | Users Manual - English - Page 17
various preparations required before starting to sew are described in this chapter. Turning the Machine On/Off 16 LCD (Liquid Crystal Display) Operation 18 Winding/Installing the Bobbin 22 Upper Threading ...31 Replacing the Needle 39 Replacing the Presser Foot 43 Sewing Cylindrical Pieces 46 - Brother International LB6800THRD | Users Manual - English - Page 18
On/Off This section explains how to turn the sewing machine on and off. Power supply precautions Be sure to . ● Do not touch the plug with wet hands. Electric shock may result. ● When unplugging the machine, always turn off the main power first. Always grasp the plug to remove it from the outlet. - Brother International LB6800THRD | Users Manual - English - Page 19
supply cord into the power supply jack on the right side of the Make sure that the machine is not sewing. a machine. Press the left side of the main power switch on b the right side of the machine to turn the Insert the plug of the power supply cord into a b house hold electrical outlet - Brother International LB6800THRD | Users Manual - English - Page 20
front of the sewing machine. Change the screen Presser foot to be used c Stitches d Stitch settings and twin needle sewing thread cutting k Automatic reverse/reinforcement l Single/twin needle sewing and needle stop position Memo z A different screen is displayed when the embroidery unit is attached - Brother International LB6800THRD | Users Manual - English - Page 21
when the sewing machine is stopped. Down Up Allows the stitch width to be adjusted with the sewing speed controller (page 58). Changes the thread color display on the embroidery screen (page 133). Thread color/Time to embroider/Needle count/ Thread number (#123) (When "Thread No.#123 - Brother International LB6800THRD | Users Manual - English - Page 22
settings are complete, press d (Back key). X The initial stitch screen appears again. Memo z "NO" is the individual number for the sewing machine. z "VERSION" is the program version which is installed in the sewing machine. z Settings that are changed are saved even if the power is turned off. 20 - Brother International LB6800THRD | Users Manual - English - Page 23
to the item 1 selection screen. bobbin winding / setting bobbin thread / needle replacement / embroidery unit attachment / Example: Upper threading embroidery frame attachment / embroidery foot attachment / presser foot replacement on the LCD. Turn on the sewing machine. a X The LCD comes on - Brother International LB6800THRD | Users Manual - English - Page 24
how to wind the thread onto the bobbin, and then insert the bobbin thread. Bobbin precautions Be sure to observe the following precautions concerning the bobbin. CAUTION ● Only use the Bobbin (part code: SA156, SFB (XA5539-151)) designed specifically for this sewing machine. Use of any other - Brother International LB6800THRD | Users Manual - English - Page 25
Turn on the sewing machine. a Place the spool of thread for the bobbin onto e the spool pin. Slide the spool onto the pin so that the spool is horizontal and the thread unwinds to the front at the bottom. 1 Place the bobbin on the bobbin winder shaft so b that the spring on the shaft fits into - Brother International LB6800THRD | Users Manual - English - Page 26
used, the upper thread tension may become tighter. Before sewing, refer to "Adjusting the thread tension" (page 59). a b a a Thread guide cover Pull the thread to the right, pass it under the i hook of the bobbin-winding thread guide, and then wind the thread counterclockwise under the pretension - Brother International LB6800THRD | Users Manual - English - Page 27
/stop button) once to stop the machine. When the foot controller is plugged in, remove your foot from the foot controller. X The bobbin winding will stop. CAUTION ● When the bobbin winding stops or becomes slow, stop the machine. Otherwise, the sewing machine may be damaged. Winding/Installing the - Brother International LB6800THRD | Users Manual - English - Page 28
When the sewing machine is started or the handwheel is turned after winding the bobbin, the machine will make a clicking sound; this is not a malfunction. b a a Thread b Bobbin winder seat CAUTION ● Do not remove the bobbin winder seat even if the thread become tangled under the bobbin winder seat - Brother International LB6800THRD | Users Manual - English - Page 29
guide Slide the bobbin winder shaft to the left, and c then remove the bobbin from the shaft. Hold the thread end with your left hand, and d wind off the thread clockwise near the bobbin with your right hand as shown below. ● The included bobbin was designed specifically for this sewing machine - Brother International LB6800THRD | Users Manual - English - Page 30
button b Presser foot lever Turn off the sewing machine. b Slide the bobbin cover latch to the right. c a b • Be sure to insert the bobbin correctly. CAUTION ● Be sure to insert the bobbin and depress it to the bottom with your finger. Otherwise, the thread may break or the thread tension will - Brother International LB6800THRD | Users Manual - English - Page 31
down on the right side. a b 2 1 a Tab b Lower-left corner X The bobbin threading is finished. You can begin sewing without pulling up the bobbin thread. Next, thread the upper thread. Continue with the procedure in "Upper Threading" (page 31). Memo z When making gathers or before free-motion - Brother International LB6800THRD | Users Manual - English - Page 32
upward to pull e out the end of the bobbin thread. Pull out about 10-15 cm (4-5 inches) of the f bobbin thread under the presser foot toward the rear of the machine. Reattach the bobbin cover. g Insert the tab in the lower-left corner of the bobbin cover, and then lightly press down on the right - Brother International LB6800THRD | Users Manual - English - Page 33
follow the instructions. If the upper threading is not correct, the thread may become tangled or the needle may bend or break. ● The needle threader can be used with a 75/11 through 100/16 home sewing machine needle. When using special thread such as transparent nylon thread or metallic thread, the - Brother International LB6800THRD | Users Manual - English - Page 34
at this position, press (Needle position button) until it is. Raise the presser foot lever. b a a a Presser foot lever X The presser foot is raised. Memo z If the presser foot is not raised, the sewing machine cannot be threaded. a Mark on handwheel Pick up the spool pin and remove the spool - Brother International LB6800THRD | Users Manual - English - Page 35
may break. Pull the thread from the spool and pass the g thread under the hook of the thread guide. a a Thread guide a b d c a Thread guide cover b Thread guide spring c Thread d When the presser foot lever is lowered Note z When passing the thread behind the thread guide cover, be sure to - Brother International LB6800THRD | Users Manual - English - Page 36
thread guide by holding the thread in your left hand, then feeding the thread with your right hand, as shown. a b a a Notch of the thread guide b Thread guide disc Cut the thread with the cutter on the left side n of the machine. a a Thread cutter a Needle bar thread guide Lower the presser foot - Brother International LB6800THRD | Users Manual - English - Page 37
Raise the presser foot lever, and carefully pull q the loop of the thread through the eye of the Ta needle to pull out the end of the thread. Tb a of "Threading the upper thread" (page 32). z CAUTION ● Do not touch a button. If a button is accidentally pressed, the machine starts sewing, and - Brother International LB6800THRD | Users Manual - English - Page 38
the machine to the needle bar thread a guide according to steps a through k on "Threading the upper thread" (page 32). Lower the presser foot lever. b a a Presser foot lever Pass the thread through the eye of the needle c from front to back. Using the twin needle With the twin needle, you can sew - Brother International LB6800THRD | Users Manual - English - Page 39
using the twin needle, be sure to attach zigzag foot "J". If bunched stitches occur, use presser foot "N" or attach stabilizer material. • For details, refer to steps g through j of "Threading the upper thread" (page 33). Turn on the sewing machine and select a h stitch. • For stitch selection see - Brother International LB6800THRD | Users Manual - English - Page 40
the sewing direction, press (Needle position button) to raise the needle from the fabric, and then raise the presser foot lever and turn the fabric. CAUTION ● Do not try turning the fabric with the twin needle left down in the fabric, otherwise the needle may break or the machine - Brother International LB6800THRD | Users Manual - English - Page 41
break, possibly resulting in injuries. Selecting the needle depending on the thread and fabric types The sewing machine needle should be used depends on the fabric and thread thickness. Refer to the following table when choosing the thread and needle appropriate for the fabric that you wish to - Brother International LB6800THRD | Users Manual - English - Page 42
colored) To avoid skipped stitches use ball point needles with stretch fabrics. ■ Transparent nylon thread Use a 90/14 to 100/16 needle, regardless of the fabric or thread. ■ Embroidery needles Use a 75/11 home sewing machine needle. When embroidering on thick fabrics such as denim, use a 90/14 or - Brother International LB6800THRD | Users Manual - English - Page 43
instructions in "Checking the needle" (page 40). Press (Needle position button) once or a twice to raise the needle. a Lower the presser foot lever. d 1 a a Presser foot otherwise certain parts of the sewing machine may be damaged. Place fabric or paper under the presser foot c and cover the holes - Brother International LB6800THRD | Users Manual - English - Page 44
GETTING READY While holding the needle with your left hand, g use the screwdriver to tighten the needle clamp screw. Install the twin needle in the same way. CAUTION z Be sure to insert the needle until it touches the needle stopper and securely tighten the needle clamp screw with the screwdriver. - Brother International LB6800THRD | Users Manual - English - Page 45
or damage to the machine. Replacing the presser foot Replace the presser foot as described below. Memo z For details on attaching the embroidery foot "Q", refer to "Attaching the Embroidery Foot" (page 120). z Zigzag foot "J" is already installed when the sewing machine is purchased. Press (Needle - Brother International LB6800THRD | Users Manual - English - Page 46
is selected, the icon for the presser foot that should be used appears in the screen. Check that the correct presser foot is attached before starting to sew. If the wrong presser foot is installed, turn off the sewing machine, attach the correct presser foot, and then select the desired stitch again - Brother International LB6800THRD | Users Manual - English - Page 47
side of the presser bar. embroidery foot, optional free-motion open toe quilting foot "O" and optional walking foot. Use the screwdriver to remove the presser foot holder. CAUTION z Before attaching/removing the presser foot, be sure to turn off the sewing machine. Otherwise, injuries may occur - Brother International LB6800THRD | Users Manual - English - Page 48
cylindrical pieces such as sleeve cuffs and pant legs. Remove the flat bed attachment. a a a Flat bed attachment X With the flat bed attachment removed, freearm sewing is possible. Slide the part that you wish to sew onto the b arm, and then sew from the top. a a Arm When you have finished free-arm - Brother International LB6800THRD | Users Manual - English - Page 49
2 SEWING BASICS The necessary preparations for sewing are described in this chapter. Sewing...48 Setting the Stitch ...57 Useful Functions...61 Useful Sewing Tips 65 - Brother International LB6800THRD | Users Manual - English - Page 50
presser foot. Attach the presser foot that is appropriate for the type of stitch that you wish to sew. Be sure to turn off the main power before replacing the presser foot. For details on replacing the presser foot, refer to "Replacing the presser foot" (page 43). ↓ 2 Turn on the machine. Turn - Brother International LB6800THRD | Users Manual - English - Page 51
off the sewing machine, attach the correct presser foot, and then select the desired stitch again. Memo z For details on setting the automatic reverse/ reinforcement stitching etc., refer to "Useful Functions" (page 61). z For details on adjusting the stitch width, stitch length and thread tension - Brother International LB6800THRD | Users Manual - English - Page 52
SEWING BASICS Positioning the fabric Be sure that the fabric pieces are sewn in the correct order and that the right and wrong sides of the fabric are aligned correctly. Turn on the machine. a While holding the end of the thread and the d fabric with your left hand, turn the handwheel toward you - Brother International LB6800THRD | Users Manual - English - Page 53
. d • For details, refer to "Cutting the thread" (page 55). a a Sewing speed controller Press (Start/stop button) once. b Note z This machine will automatically stop when the bobbin becomes almost empty. When the machine stops, replace the bobbin thread, and then press (Start/stop button) to begin - Brother International LB6800THRD | Users Manual - English - Page 54
controller. Pressing it down hard starts sewing too quickly. X The machine starts sewing. When the end of the stitching is reached, f completely release the foot controller. X The machine stops sewing with the needle lowered (in the fabric). Cut the threads. g • For details, refer to "Cutting the - Brother International LB6800THRD | Users Manual - English - Page 55
Lower the needle into the fabric at the sewing is stopped, refer to "Changing the machine settings" (page 19). a beginning of the stitching, and then lower the presser foot lever. 2 CAUTION z Do not allow thread or dust to accumulate in the foot controller, otherwise a fire or an electric shock - Brother International LB6800THRD | Users Manual - English - Page 56
stop button), or press down on h the foot controller. At this time, if (Start/stop button) is held down, the machine sews at a slow speed. X The machine starts sewing in the normal sewing direction. After sewing to the end of the stitching, the i sewing machine stops. Release (Start/stop button) or - Brother International LB6800THRD | Users Manual - English - Page 57
, otherwise the needle may break, the threads may become tangled or damage to the machine may occur. z Do not press (Thread cutter button) if there is no fabric under the presser foot or while the machine is sewing, otherwise damage to the machine may occur. Memo z The machine can be set so that the - Brother International LB6800THRD | Users Manual - English - Page 58
cutter on the side of the machine to cut the threads. When you wish to finish the stitching and the a sewing machine is stopped, press (Needle position button) once to raise the needle. a a Needle position button Raise the presser foot lever. b a a Presser foot lever Pull the fabric to the left - Brother International LB6800THRD | Users Manual - English - Page 59
Stitch settings return to their defaults if they are changed, when the machine is turned off or a different stitch is selected before the stitch setting to return the setting to its default. z If the foot controller is connected, the sewing speed controller can be used to adjust the zigzag width. - Brother International LB6800THRD | Users Manual - English - Page 60
, refer to "Using the foot controller" (page 52). Attach zigzag foot "J". b J Press e (Back key). X The initial screen appears again. Select a stitch. f • For details on replacing the presser foot, refer to "Replacing the presser foot" (page 43). Turn on the sewing machine, and then press - Brother International LB6800THRD | Users Manual - English - Page 61
, increase the stitch length. Continuing to sew with the stitches bunched together may result in the needle bending or breaking. c d a Wrong side of fabric b Right side of fabric c Upper thread d Bobbin thread ■ Upper thread is too tight If the bobbin thread is visible from the right side of - Brother International LB6800THRD | Users Manual - English - Page 62
. z The machine may stop sewing if tension is set extremely low. This is not a sign that there is anything wrong with your machine. Simply adjust to the correct stitch tension and begin again. b c d a Wrong side of fabric b Right side of fabric c Upper thread d Bobbin thread e The upper thread is - Brother International LB6800THRD | Users Manual - English - Page 63
reverse/ reinforcement stitches Position the fabric under the presser foot, and d then press (Start/stop button) once. The sewing machine can be set to automatically sew reverse or reinforcement stitches at the beginning and end of the stitching. Depending on the selected stitch, 2 reverse - Brother International LB6800THRD | Users Manual - English - Page 64
2a 4 3b X You get , and the sewing machine is set for programmed thread-cutting and automatic reverse/reinforcement stitching. a Stop the machine and change the sewing direction. b Start the machine again. Automatically cutting the thread The sewing machine can be set to automatically cut the - Brother International LB6800THRD | Users Manual - English - Page 65
Press (Start/stop button) when you want to stop the sewing machine in the middle of sewing without programmed thread-cutting (for example, when you want to change the sewing direction). The sewing machine stops without programmed thread cutting. Press (Reverse/reinforcement stitch button) at the end - Brother International LB6800THRD | Users Manual - English - Page 66
SEWING BASICS Saving stitch settings This machine is preset with the default settings for the stitch width (zigzag width), stitch length, programmed thread-cutting, and automatic reverse/ reinforcement stitching for each stitch. However, if you wish to save specific settings for a stitch so - Brother International LB6800THRD | Users Manual - English - Page 67
Various ways to achieve better results for your sewing projects are described below. Refer to these tips when sewing your project. Trial sewing Sewing curves After you have set up the machine with the thread Stop sewing, and then slightly change the sewing and needle appropriate for the type of - Brother International LB6800THRD | Users Manual - English - Page 68
. a Press the black button (presser foot holding b pin) on the left side of zigzag foot "J". Keep the button held in and lower the presser foot. CAUTION z Use only the ungummed hook-and-loop fastener which is for sewing. If the glue is attached to the needle or the bobbin hook race, it may cause - Brother International LB6800THRD | Users Manual - English - Page 69
1 2 4 a Basting Using the stretch stitches or the thread for knits gives 2 3 an attractive finishes. 4 5 9 10 34 6 Sewing an even seam allowance To sew an even seam, start sewing so that the seam allowance is to the right of the presser foot, and the edge of the fabric is aligned with - Brother International LB6800THRD | Users Manual - English - Page 70
SEWING BASICS 68 - Brother International LB6800THRD | Users Manual - English - Page 71
Setting Chart 70 Overcasting Stitches 74 Basic Stitching ...78 Blind Hem Stitching 80 Buttonhole Stitching 83 Zipper Insertion...90 Sewing Stretch Fabrics and Elastic Tape 95 Appliqué, Patchwork and Quilt Stitching 97 Reinforcement Stitching 103 Eyelet Stitching...108 Decorative Stitching - Brother International LB6800THRD | Users Manual - English - Page 72
Walking Foot Presser Foot Stitch Name Pattern Application Stitch Width [mm (inch)] Auto Manual 1 J Basic stitching, sewing Attaching zippers, basic J/I stitching, sewing gathers or pintucks, etc. Attaching sleeves, sewing J inseams, sewing stretch fabrics and decorative stitching J Sewing - Brother International LB6800THRD | Users Manual - English - Page 73
Foot Twin Needle Walking Foot Stitch Name Pattern Application 17 Blind hem stitch 18 R Blind hem stitching on mediumweight fabrics R Blind hem stitching on stretch fabrics Stitch Width [mm (inch)] Stitch Length [mm (inch)] Auto Manual Auto Manual Elastic-attaching and sewing overcasting - Brother International LB6800THRD | Users Manual - English - Page 74
UTILITY STITCHES Presser Foot Twin Needle Walking Foot Stitch Name Pattern Application 35 J Decorative stitching Stitch Width [mm (inch)] Auto 4.0 (3/16) Manual 0.0-7.0 (0-1/4) Stitch Length [mm (inch)] Auto Manual Reverse/ Reinforcement Stitching 3.0 (1/8) 2.0-4.0 (1/16-3/16) No - Brother International LB6800THRD | Users Manual - English - Page 75
Foot Twin Needle Walking Foot Stitch Name Pattern Application 48 A Horizontal buttonholes on thin and mediumweight fabrics Stitch Width [mm (inch)] Stitch Length [mm (inch)] Auto Manual Auto Manual 59 60 Bar tack stitch 61 Button-sewing stitch 62 Eyelet stitch 63 A Darning mediumweight - Brother International LB6800THRD | Users Manual - English - Page 76
Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual Presser Foot 3.5 2.0 (1/8) (1/16) 2.5-5.0 machine starts sewing. Attach overcasting foot "G". a G Position the fabric with the edge of the fabric c against the guide of the presser foot, and then lower the presser foot - Brother International LB6800THRD | Users Manual - English - Page 77
16) CAUTION ● Be sure to turn off the main power before replacing the pressor foot. Otherwise, injuries may occur if (Start/stop button) is accidentally pressed and the machine starts sewing. Attach zigzag foot "J". a J Sew along the edge of the fabric with the c needle dropping off the edge at - Brother International LB6800THRD | Users Manual - English - Page 78
pressed and the machine starts sewing. Position the side cutter so that side cutter pin c is aligned with the notch in the presser foot holder, and then slowly lower the presser foot lever. Note z Thread the needle manually when using the side cutter, or only attach the side cutter after - Brother International LB6800THRD | Users Manual - English - Page 79
Raise the presser foot lever to check that the d side cutter is securely attached. Pass the upper thread under the side cutter, e and then pull it out toward the rear of the sewing machine. Position the fabric in the side cutter. h The cut in the fabric should be positioned over the guide plate of - Brother International LB6800THRD | Users Manual - English - Page 80
inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual - - Presser Foot 1 Straight stitch Basic stitching and sewing gathers or and the machine starts sewing. Basting Attach zigzag foot "J". a • For details on replacing the presser foot, refer to "Replacing the presser foot" (page 43 - Brother International LB6800THRD | Users Manual - English - Page 81
needle position). a b When sewing is finished, cut the thread. f • For details, refer to "Cutting the thread" (page 55). a Straight position will also change. By changing the stitch width and sewing with the right side of the presser foot aligned with the edge of the fabric, a seam allowance - Brother International LB6800THRD | Users Manual - English - Page 82
[mm (inch)] Auto Manual Presser Foot 00 3← - →3 2.0 (1/16) 1.0-3.5 (1/16-1/8) R CAUTION ● Be sure to turn off the main power before replacing the pressor foot. Otherwise, injuries may occur if (Start/stop button) is accidentally pressed and the machine starts sewing. Sew a blind hem according - Brother International LB6800THRD | Users Manual - English - Page 83
1 S< Seen from the side> a Wrong side of fabric b Basting c Edge of fabric Attach blind hem foot "R". f R 3 a Arm Position the fabric with the edge of the folded j hem against the guide of the presser foot, and then lower the presser foot lever. R 1 b c a Wrong side of fabric b Fold of hem - Brother International LB6800THRD | Users Manual - English - Page 84
. 1 2 a Wrong side of fabric b Right side of fabric Memo z For details, refer to "Adjusting the stitch width" (page 57). Sew with the fold of the hem against the l presser foot guide. Remove the basting stitching and reverse the m fabric. 1 2 a Wrong side of fabric b Right side of fabric 82 - Brother International LB6800THRD | Users Manual - English - Page 85
stitches are available for sewing one-step buttonholes, one for sewing on buttons. Stitch Name Pattern Application 48 Horizontal buttonholes on thin and mediumweight fabrics Stitch Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual Presser Foot 49 Horizontal buttonholes on - Brother International LB6800THRD | Users Manual - English - Page 86
pressed and the machine starts sewing. The names of parts of buttonhole foot "A", which is used for sewing buttonholes, are indicated below. Use chalk to mark on the fabric the position a and length of the buttonhole. 1 2 5 6 3 4 A a Button guide plate b Presser foot scale c Pin d Marks - Brother International LB6800THRD | Users Manual - English - Page 87
fabric (front) b Red marks on buttonhole foot • Pass the upper thread down through the hole in the presser foot. 2 a 10 mm (3/8 inch) b 15 mm (9/16 inch) X The size of the buttonhole is set. Attach buttonhole foot "A". c • For details on replacing the presser foot, refer to "Replacing the presser - Brother International LB6800THRD | Users Manual - English - Page 88
lever The buttonhole lever is positioned behind the bracket on the buttonhole foot. a a a Seam ripper For keyhole buttonholes, use the eyelet punch of the upper thread in g your left hand, and then start sewing. X Once sewing is completed, the machine automatically sews reinforcement stitches, - Brother International LB6800THRD | Users Manual - English - Page 89
and width by sewing a trial buttonhole on a scrap piece of fabric. Attach buttonhole foot "A". c • For details on replacing the presser foot, refer to "Replacing the presser foot" (page 43). Select stitch 52 or 53 . d Adjust the stitch width to the thickness of the e gimp thread. Lower the presser - Brother International LB6800THRD | Users Manual - English - Page 90
the machine) X The feed dogs are lowered. Attach button-fitting foot "M". c • For details on replacing the presser foot, refer to "Replacing the presser foot" ( end of the thread will be tied off later, do not set the sewing machine for programmed-thread cutting. CAUTION ● When sewing, be sure that - Brother International LB6800THRD | Users Manual - English - Page 91
. Use scissors to cut the upper thread and the bobbin thread at the beginning of the stitching. When you are finished attaching the button, slide the drop feed lever to (to the right as seen from the rear of the machine). When you have finished attaching the button, j slide the drop feed lever - Brother International LB6800THRD | Users Manual - English - Page 92
Pattern Application Straight stitch (center 3 needle position) Attaching zippers Sewing concealed seams and pintucks Stitch Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual Presser Foot 3.5 0.0-7.0 2.5 0.2-5.0 (1/8) (0-1/4) (3/32) (1/64-3/16) I CAUTION ● Be sure to - Brother International LB6800THRD | Users Manual - English - Page 93
Zipper basting c Outside basting d 5 mm (2 inches) Attach the presser foot holder to the right pin g of zipper foot "I". a 1 3 2 4 I b a Pin foot, refer to "Replacing the presser foot" (page 43). a Stitching b Right side of fabric c Basting stitching d End of zipper opening CAUTION ● When sewing - Brother International LB6800THRD | Users Manual - English - Page 94
procedure will describe how to stitch on the left side, as shown in the illustration. Attach zigzag foot "J". a J • For details on replacing the presser foot, refer to "Replacing the presser foot" (page 43). Sew straight stitches up to the zipper opening. b With the right sides of the fabric facing - Brother International LB6800THRD | Users Manual - English - Page 95
the base of the zipper. 1 CAUTION ● When sewing, be sure that the needle does not touch the zipper, otherwise the needle may bend or break. a Basting stitching Attach the presser foot holder to the other pin m of zipper foot "I". If the presser foot holder was attached to the right pin in step - Brother International LB6800THRD | Users Manual - English - Page 96
not touch the zipper, otherwise the needle may bend or break. When you are about 5 cm (2 inches) from the o end of the zipper, stop the sewing machine with the needle lowered (in the fabric), and then raise the presser foot lever. Remove the basting stitching, open the zipper, p and then continue - Brother International LB6800THRD | Users Manual - English - Page 97
● Be sure to turn off the main power before replacing the pressor foot. Otherwise, injuries may occur if (Start/stop button) is accidentally pressed and the machine starts sewing. Stretch stitching Attach zigzag foot "J". a J Sew the fabric without stretching it. c • For details on replacing the - Brother International LB6800THRD | Users Manual - English - Page 98
your right hand. 1 2 a Elastic tape b Pin Attach zigzag foot "J". b J • For details on replacing the presser foot, refer to "Replacing the presser foot" (page 43). Select a stitch. c • For details, refer to "Selecting stitching" (page 49). CAUTION ● When sewing, be sure that the needle does not - Brother International LB6800THRD | Users Manual - English - Page 99
stitching Stitch Width [mm (inch)] Auto Manual 0.0-7.0 3.5 (0-1/4) (1/8) Stitch Length [mm (inch)] Auto Manual 1.4 0.0-4.0 (1/16) (0-3/16) Presser Foot 19 Appliqué stitch 25 Attaching appliqués 2.5-7.0 2.5 1.6-4.0 (3/32-1/4) (3/32) (1/16-3/16) Attaching appliqués and binding 1.5 (1/16 - Brother International LB6800THRD | Users Manual - English - Page 100
or fuse it c onto the fabric that it will be attached to. 1 a Basting stitching Attach zigzag foot "J". d J • For details on replacing the presser foot, refer to "Replacing the presser foot" (page 43). When sewing around corners, stop the machine with the needle in the fabric just outside of the - Brother International LB6800THRD | Users Manual - English - Page 101
with a 6.5 mm (1/4 inch) seam allowance. Sew a piecing straight stitch 6.5 mm (1/4 inch) from either the right side or the left side of the presser foot. Baste or pin along the seam allowance of the a fabric that you wish to piece together. Attach zigzag foot "J". b J • For details on replacing the - Brother International LB6800THRD | Users Manual - English - Page 102
screw, and then tighten the screw with the screwdriver. a Walking foot Quilting guide Note z When sewing with the walking foot, sew at a speed between slow and medium. z When quilting, use a 90/14 home sewing machine needle. z The walking foot can only be used with straight or zigzag stitch - Brother International LB6800THRD | Users Manual - English - Page 103
Use the quilting guide to sew parallel stitches that are equally spaced. Insert the stem of the quilting guide into the a hole at the rear of the walking foot or presser foot holder. † Walking foot 3 † Presser foot holder Adjust the stem of the quilting guide so that b the guide aligns with the - Brother International LB6800THRD | Users Manual - English - Page 104
45). Attach free-motion quilting foot "O" by b positioning the pin of the quilting foot above the needle clamp screw and aligning the lower-left of the quilting foot and the presser bar. 1 3 2 a a Drop feed lever (as seen from the rear of the machine) X The feed dogs are lowered. Turn on the sewing - Brother International LB6800THRD | Users Manual - English - Page 105
Application Stitch Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual Presser Foot Triple stretch 4 stitch Reinforcing the seams and the machine starts sewing. Triple stretch stitching Use triple stretch stitching to reinforce sleeve holes and inseams. Attach zigzag foot "J". a - Brother International LB6800THRD | Users Manual - English - Page 106
of the bar tack. a Set the button guide plate on buttonhole foot "A" to the desired length. (The distance between the markings on the presser foot scale is 5 mm (3/16 inch).) 1 • Pass the upper thread down through the hole in the presser foot. 2 3 a Presser foot scale b Length of bar tack c 5 mm - Brother International LB6800THRD | Users Manual - English - Page 107
Gently hold the end of the upper thread in f your left hand, and then start sewing. X Once sewing is completed, the sewing machine automatically sews reinforcement stitches, then stops. Raise the presser foot lever, remove the fabric, g and then cut the threads. Raise the buttonhole lever to its - Brother International LB6800THRD | Users Manual - English - Page 108
guide plate on buttonhole foot "A" to the desired length. (The distance between the markings on the presser foot scale Attach buttonhole foot "A". b • For details on replacing the presser foot, refer to "Replacing the presser foot" (page 43). 1 2 a Tear b 2 mm (1/16 inch) • Pass the upper thread - Brother International LB6800THRD | Users Manual - English - Page 109
Pull down the buttonhole lever as far as e possible. X Once sewing is completed, the sewing machine automatically sews reinforcement stitches, then stops. Raise the presser foot lever, remove the fabric, g and then cut the threads. Raise the buttonhole lever to its original 3 h position. Memo - Brother International LB6800THRD | Users Manual - English - Page 110
)] Auto Manual 7.0, 6.0 or 7.0 5.0 (1/4) (1/4, 15/64 or 3/16) Presser Foot N CAUTION ● Be sure to turn off the main power before replacing the pressor foot. Otherwise, injuries may occur if (Start/stop button) is accidentally pressed and the machine starts sewing. Attach monogramming foot - Brother International LB6800THRD | Users Manual - English - Page 111
Sewing two pieces of fabric together across an open seam Stitch Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual Presser Foot (3/32) 1.5-4.0 (1/16-3/16) 44 2.0 (1/16) 45 Decorative hemming, ribbon threading, heirloom stitching, etc. 3.0 (1/8) Decorative Stitching 109 - Brother International LB6800THRD | Users Manual - English - Page 112
you draw a line down the middle of the thin paper or water-soluble stabilizer, sewing is easier. 3 Attach zigzag foot "J". c J • For details on replacing the presser foot, refer to "Replacing the presser foot" (page 43). Select stitch 32 or 33 . d • For details, refer to "Selecting stitching" (page - Brother International LB6800THRD | Users Manual - English - Page 113
on the collars of blouses and to decorate the edges of projects. Attach monogramming foot "N". a After sewing is finished, remove the paper. g • For details on replacing the presser foot, refer to "Replacing the presser foot" (page 43). Select stitch 27 . 3 b • For details, refer to "Selecting - Brother International LB6800THRD | Users Manual - English - Page 114
" (page 49). Attach zigzag foot "J". a J • For details on replacing the presser foot, refer to "Replacing the presser foot" (page 43). Select the straight stitch, and then adjust the b stitch length to 4.0 mm (3/16 inch) and loosen the thread tension. • Pull up the bobbin thread. For details, refer - Brother International LB6800THRD | Users Manual - English - Page 115
down to one side. Attach zigzag foot "J". 3 b J • For details, refer to "Replacing the presser foot" (page 43). Select stitch 20 , and then increase the c thread tension. • For details, refer to "Selecting stitching" (page 49) and "Adjusting the thread tension" (page 59). Sew while making sure - Brother International LB6800THRD | Users Manual - English - Page 116
wing needle, otherwise the sewing machine may be damaged. Manually pass the thread through the eye of the needle from the front to the back. For details, refer to "Threading the needle manually (without using the needle threader)" (page 36). Attach monogramming foot "N". b • For details on replacing - Brother International LB6800THRD | Users Manual - English - Page 117
described below. ■ Drawnwork (Example 1) Pull out several threads from the fabric. a 3 Note z When sewing with the wing needle, select a stitch width of 6.0 mm (15/64 inch) or less. Start sewing. d Attach monogramming foot "N". b CAUTION ● When sewing with the wing needle, select a stitch width - Brother International LB6800THRD | Users Manual - English - Page 118
key back to OFF. 1 a 4 mm (3/16 inch) Attach monogramming foot "N" . b • For details on replacing the presser foot, refer to "Replacing the presser foot" (page 43). Select stitch 42 . c • For details, refer to "Selecting stitching" (page 49). Sew along the center of the unfrayed section. d N 116 - Brother International LB6800THRD | Users Manual - English - Page 119
steps for embroidering are described in this chapter. Embroidering Neatly 118 Attaching the Embroidery Foot 120 Attaching the Embroidery Unit 123 Preparing the Fabric 126 Attaching the Embroidery Frame 130 Selecting Embroidery Patterns 132 Embroidering...139 Editing and Saving Patterns 143 - Brother International LB6800THRD | Users Manual - English - Page 120
for embroidery machines. z Before starting to sew, be sure there is enough bobbin thread. If you continue embroidering when the bobbin thread is low, the thread may become tangled. CAUTION ● Do not embroider fabrics that are too thick. To check the fabric thickness, attach the embroidery frame to - Brother International LB6800THRD | Users Manual - English - Page 121
Bobbin thread setup For the bobbin thread, wind embroidery bobbin thread and set it in place. For details on setting up the bobbin thread, refer to "Winding/Installing the Bobbin" (page 22). 5 Fabric preparation ↓ 4 Attach a stabilizer material to the fabric, and hoop it in an embroidery frame - Brother International LB6800THRD | Users Manual - English - Page 122
EMBROIDERY Attaching the Embroidery Foot This section describes how to attach the embroidery foot "Q". Attaching the embroidery foot Attach the embroidery foot "Q" when embroidering. Have the included embroidery foot "Q" and a screwdriver ready. Turn off the sewing machine. b a b a Embroidery - Brother International LB6800THRD | Users Manual - English - Page 123
the presser foot and break or bend. ● Before sewing, always turn the handwheel toward you (counterclockwise) slowly to make sure that the needle does not hit the presser foot. The needle may break or bend. a Presser bar b Needle clamp screw c Embroidery foot bar Attaching the Embroidery Foot 121 - Brother International LB6800THRD | Users Manual - English - Page 124
position button Turn off the sewing machine. b a Screwdriver Attach the presser foot holder. e • For details, refer to "Removing and attaching the presser foot holder" (page 45). CAUTION z Before removing the embroidery foot, be sure to turn off the sewing machine. Otherwise, injuries may occur if - Brother International LB6800THRD | Users Manual - English - Page 125
to attach the embroidery unit. Embroidery unit precautions Attaching the embroidery unit CAUTION ● Do not move the sewing machine with the embroidery unit in place. The embroidery unit may be dropped and cause injury. ● Keep your hands and other objects away from the embroidery carriage and frame - Brother International LB6800THRD | Users Manual - English - Page 126
fully insert the connector into the connection port. z Do not push on the carriage when attaching the embroidery unit to the machine, otherwise damage to the embroidery unit may result. Turn on the sewing machine. d a Carriage CAUTION ● Do not put your hands or other objects near the carriage. It - Brother International LB6800THRD | Users Manual - English - Page 127
unit Make sure that the sewing machine is completely stopped and follow the instructions below. Remove the embroidery frame. a • For details on removing the embroidery frame, refer to "Removing the embroidery frame" (page 131). Press , and then press . b Hold the release button on the - Brother International LB6800THRD | Users Manual - English - Page 128
materials like organdy and fabrics with a nap like towels. To obtain optional accessories or parts, visit [http://www.brother.com/], or [http:// www.brothermall.com] (in USA). a c b a Fabric b Size of embroidery frame c Stabilizer material If you are using stabilizers with adhesive, place b the - Brother International LB6800THRD | Users Manual - English - Page 129
pattern may be poor. Put the fabric in the frame without slack following the steps below. Have a fabric with a stabilizer material attached and the embroidery frame (medium, small or large) ready. ■ Embroidery frame (medium) Patterns with a height of up to 10 cm (4 inches) and a width of up - Brother International LB6800THRD | Users Manual - English - Page 130
again, lining up on the inner frame and on outer frame. ■ Using embroidery sheets If the embroidery sheet attached to the embroidery frame is used, the embroidery can be sewn in exactly the right position on the fabric. Embroidery sheet (medium) Embroidery sheet (small) [option] 3 12 54 a Outer - Brother International LB6800THRD | Users Manual - English - Page 131
the mark on the fabric up with the base c line on the embroidery sheet. ■ Embroidery on fabrics that cannot be stretched on an embroidery frame When small pieces of fabric that cannot be stretched on an embroidery frame or thin pieces like ribbon are being embroidered, use stabilizer material as - Brother International LB6800THRD | Users Manual - English - Page 132
attach the embroidery frame. Attaching the embroidery frame Wind the embroidery bobbin thread onto the a bobbin and set it into the bobbin case. • For details, refer to "Winding/Installing the Bobbin" (page 22). Firmly insert the embroidery frame guide into e the embroidery carriage frame holder - Brother International LB6800THRD | Users Manual - English - Page 133
Removing the embroidery frame Pass the embroidery frame under the presser d foot while raising the presser foot lever even further. Make sure that the sewing machine is completely stopped and follow the instructions below. Raise the presser foot lever. a a a Presser foot lever Press (Needle - Brother International LB6800THRD | Users Manual - English - Page 134
pattern. Copyright information The patterns saved in the sewing machine and embroidery cards are intended for private use only. Any public by changing the upper thread according to the instructions displayed on the screen. For details, refer to "Selecting an embroidery pattern" (page 137). - Brother International LB6800THRD | Users Manual - English - Page 135
to adjust language or change the thread color display or other settings. e Press to get help on embroidery unit attachment, embroidery frame attachment, etc. f Press this key to save embroidery patterns and the alphabet characters in the machine's memory. Selecting Embroidery Patterns 133 - Brother International LB6800THRD | Users Manual - English - Page 136
(POLYESTER) THREAD# is selected.) •EMBROIDERY (POLYESTER) THREAD# •COUNTRY (COTTON) THREAD# •MADEIRA POLY THREAD# •MADEIRA RAYON THREAD# •SULKY THREAD# •ROBISON-ANTON POLY THREAD# When a specific pattern is selected, press this key and then, press to switch the display. The sewing settings such - Brother International LB6800THRD | Users Manual - English - Page 137
4 Press this key when you want to change the color, character by character in character embroidery. Since the sewing machine stops at the end of each character, the upper thread is changed as you sew. Press this key again to cancel multicolor. Memo z Keys that appear surrounded with a dotted line - Brother International LB6800THRD | Users Manual - English - Page 138
. Memo z When "The pattern is too large for the embroidery frame" is displayed, no more characters can be input. z Characters from different fonts (sans serif and serif, etc.) cannot be combined. Select the alphabet characters. a Select - Brother International LB6800THRD | Users Manual - English - Page 139
as flowers and animals, saved in the machine's memory. 70 Embroidery patterns Memo z Refer to "Embroidery Pattern Color Change Table" in the Quick reference guide for samples of completed patterns and the thread used. Press . a Selecting a frame pattern 10 shapes, such as squares and circles - Brother International LB6800THRD | Users Manual - English - Page 140
using (Previous page key) and (Next page key), and select from the 12 stitches. Insert the embroidery card in the embroidery b card slot on the right side of the sewing machine. Face the arrow on the embroidery card toward you, and insert it in the direction of the arrow. X When a stitch is - Brother International LB6800THRD | Users Manual - English - Page 141
through the embroidery foot c hole, and hold it lightly in your left hand. (liquid crystal display) operation" (page 133). Give the thread a little slack. CAUTION ● If the thread is pulled too tight, the needle may break or bend. ● Do not let hands or objects hit the carriage while sewing. The - Brother International LB6800THRD | Users Manual - English - Page 142
the size of the pattern being embroidered. Otherwise, the embroidery frame may be hit by the presser foot and cause injury or needle breakage. After progressing 5-6 stitches, press f (Start/stop button) to stop the machine. Use scissors to cut the thread at the beginning g of the stitching. Cut the - Brother International LB6800THRD | Users Manual - English - Page 143
the embroidery e frame. X "APPLIQUE MATERIAL" is displayed on the screen. Set up the thread for foot lever, and press g (Start/stop button). embroidery frame. 4 Lower the presser foot lever, and press c (Start/stop button). X The cut-out for the appliqué piece is sewn, and the sewing machine - Brother International LB6800THRD | Users Manual - English - Page 144
EMBROIDERY Apply a thin layer of fabric glue or spray h adhesive to the back of the appliqué piece, and attach it in the appliqué position. Lower the presser foot lever, and press i (Start/stop button). X The position for the appliqué is stitched, and the sewing machine stops. Memo z When "APPLIQUE - Brother International LB6800THRD | Users Manual - English - Page 145
key/Layout key f Rotation key g Horizontal mirror image key 4 X The sewing screen is displayed. h Trial key i Starting point key j Distance from the center k Embroidery size Press . b Embroidery frame size The size of embroidery frame that can be used is displayed. When the smaller mark is - Brother International LB6800THRD | Users Manual - English - Page 146
z You can save patterns you have changed the size and position in the machine's memory. Refer to "Saving patterns" (page 150). Layout key Press this Memo z Mirroring patterns is possible only for a embroidery pattern or a frame pattern. Starting point stitching key Switches the stitching starting - Brother International LB6800THRD | Users Manual - English - Page 147
embroidering. z The embroidery patterns you have edited or adjusted can be saved in the sewing machine's memory. For details, refer to a b a Right side of fabric b Wrong side of fabric "Saving patterns" (page 150). Note z If the upper thread is not threaded correctly or the bobbin is not - Brother International LB6800THRD | Users Manual - English - Page 148
of the design. Lower the presser foot, and then press g (Start/stop switch) to begin sewing. When embroidering is finished, trim the thread h leaving the end of the thread longer than usual. Then reset the fabric in the embroidery frame, in a position where you can sew "DEF". Press c (Back key - Brother International LB6800THRD | Users Manual - English - Page 149
of "ABC". a a Embroidery end position Lower the presser foot, and then press m (Start/Stop button) to embroider "DEF". Resewing When the wrong upper thread color has been sewn, it can be resewn with the correct color. Press (Start/stop button) to stop the a sewing machine. Press . b Press - Brother International LB6800THRD | Users Manual - English - Page 150
design When the upper thread or the bobbin thread runs out while sewing, the sewing machine stops. Move the needle back about 10 stitches and resume sewing. Memo z When the bobbin thread runs out, cut the threads and remove the embroidery frame before replacing the bobbin thread. Set up the upper - Brother International LB6800THRD | Users Manual - English - Page 151
Forward one color) to move to i the beginning of the color you want to embroider. Note z Always detach the embroidery unit when you move the sewing machine. Press (Forward one stitch) to increase j the needle count. If is pressed continuously, it moves forward 1 -> 9 ->30 stitches. 4 Turn - Brother International LB6800THRD | Users Manual - English - Page 152
patterns and the alphabet characters you have customized can be saved in the sewing machine's memory. Since the saved patterns will not be erased when the power is turned off, you can always retrieve them for embroidery. This is convenient for saving names and the like. You can save up to 12 - Brother International LB6800THRD | Users Manual - English - Page 153
5 APPENDIX The various maintenance and troubleshooting procedures are described in this chapter. Care and Maintenance 152 Troubleshooting ...154 Index ...165 - Brother International LB6800THRD | Users Manual - English - Page 154
. Remove the bobbin case. f Grasp the bobbin case, and then pull it out. CAUTION ● Unplug the power supply cord before cleaning the machine. Otherwise, injuries or an electric shock may occur. Remove the flat bed attachment or the c embroidery unit if either is attached. a a Bobbin case 152 - Brother International LB6800THRD | Users Manual - English - Page 155
plate cover CAUTION ● Never use a bobbin case that is scratched. Otherwise, the upper thread may become tangled, the needle may break or sewing performance may suffer. For a new bobbin case (part code: XC3152-221 (green marking)), contact your nearest authorized service center. ● Be sure that the - Brother International LB6800THRD | Users Manual - English - Page 156
Center offers the latest FAQs and troubleshooting tips. Visit us at [http://solutions.brother.com]. If the problem persists, contact your dealer or the nearest authorized service center. Symptom Probable Cause Remedy The machine is not turned on. Turn on the machine. The start/stop button was - Brother International LB6800THRD | Users Manual - English - Page 157
machine. page 22 Bobbin thread does not wind neatly on the bobbin. The thread is not passed through the bobbin-winding thread guide correctly. Bobbin spins slowly. The thread that was pulled out was not wound onto the bobbin correctly. Correctly pass the thread through the bobbin-winding thread - Brother International LB6800THRD | Users Manual - English - Page 158
presser foot holder. The thread tension is incorrect. Adjust the tension of the upper thread. A bobbin designed specifically for this machine is not used. Incorrect bobbins will not work properly. Only use a bobbin designed specifically for this machine. The upper thread is The bobbin thread is - Brother International LB6800THRD | Users Manual - English - Page 159
the type of stitch that you wish to sew. Attach the presser foot that is appropriate for the type of stitch that you wish to sew. page 70 The thread is tangled, for example, in the bobbin case. Remove the tangled thread. If the thread is tangled in the bobbin case, clean the race. page 152 The - Brother International LB6800THRD | Users Manual - English - Page 160
unit movement will be impaired. Support the fabric while embroidering. The fabric is catching. It is pinched. Stop the sewing machine and set the fabric up correctly. The carriage was moved while the embroidery frame was being removed or attached during embroidery. If the carriage is moved - Brother International LB6800THRD | Users Manual - English - Page 161
may be wrong or the needle may break and cause injury. 6 The machine is deleting a previously saved pattern while in embroidery edit mode. The start/stop button was pressed while the foot controller was 7 connected. You tried to use the foot controller for embroidery. Troubleshooting 159 - Brother International LB6800THRD | Users Manual - English - Page 162
pressing the manual memory key. You tried to select an embroidery pattern or change the layout when 15 the needle was down. The machine is turned on while the needle is lowered and the embroidery unit is attached. 16 You tried to initialize the embroidery unit with the embroidery foot lowered - Brother International LB6800THRD | Users Manual - English - Page 163
the frame. The upper thread has become tangled around the bobbin case, and the 24 needle is bent and hitting the needle plate, etc., so the sewing machine stops (refer to page 154). 25 You tried to use a function that cannot be used when the embroidery unit is attached. Troubleshooting 161 - Brother International LB6800THRD | Users Manual - English - Page 164
a pattern downloaded as one for a different machine. The start/stop button, the embroidery key, or the memory key is pressed in embroidery mode, but the embroidery unit is not attached. 28 The embroidery key was pressed when the embroidery unit is not attached. 29 The bobbin winder is winding the - Brother International LB6800THRD | Users Manual - English - Page 165
) One beep sounds. ■ If an incorrect operation is performed Two or four beeps sound. ■ If the machine locks up, for example, because the thread is tangled The sewing machine beeps for four seconds and the machine automatically stops. Be sure to check for the cause of the error, and correct it before - Brother International LB6800THRD | Users Manual - English - Page 166
APPENDIX Press OFF for the buzzer. d X The screen for changing the beep setting appears. Press e (Back key). X The initial stitch screen appears again. 164 - Brother International LB6800THRD | Users Manual - English - Page 167
dogs 11 flat bed attachment 10 foot controller 9, 52 changing sewing direction 65 foot controller jack 11 checking needle 40 frame pattern selection 137 cleaning bobbin case 152 fraying, preventing 74 cleaning brush 9 free-arm sewing 46 cleaning machine surface 152 free-motion - Brother International LB6800THRD | Users Manual - English - Page 168
LCD 18, 133 LCD button 134 LCD messages 159 LCD operation 18 M machine surface cleaning 152 main power switch 11 maintenance 152 manual needle threading 36 memory key 13 mirroring stitches 63 N needle bar thread guide 11 needle condition 40 needle plate 11 needle plate cover 11 needle - Brother International LB6800THRD | Users Manual - English - Page 169
34 thread spools 31 thread take-up lever 10, 34 thread tension adjustment 59, 145 threading 31 threading bobbin 22 5 threading needle 31 threading needle manually 36 tips 65 touch panel 13 trial sewing 65 triple stretch stitch 78, 95, 103 troubleshooting 154 turning machine on - Brother International LB6800THRD | Users Manual - English - Page 170
- Brother International LB6800THRD | Users Manual - English - Page 171
- Brother International LB6800THRD | Users Manual - English - Page 172
English XE3116-201c Printed in China
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
 |
 |
Product Code
885-V31/V32/V33
GETTING READY
SEWING BASICS
UTILITY STITCHES
EMBROIDERY
APPENDIX
Please visit us at
where you can get product support and answers to
frequently asked questions (FAQs).
Computerized Embroidery and Sewing Machine
Operation Manual