Brother International NX-650Q Users Manual - English
Brother International NX-650Q Manual
 |
View all Brother International NX-650Q manuals
Add to My Manuals
Save this manual to your list of manuals |
Brother International NX-650Q manual content summary:
- Brother International NX-650Q | Users Manual - English - Page 1
GETTING READY Read before use. SEWING BASICS Read when additional information is required. UTILITY STITCHES APPENDIX Computerized Sewing Machine Operation Manual - Brother International NX-650Q | Users Manual - English - Page 2
the instruction manual: • To unplug the machine, switch the machine to machine to the nearest authorized dealer or service center for examination, repair, electrical or mechanical adjustment. While the machine machine with any air openings blocked. Keep ventilation openings of the sewing machine and - Brother International NX-650Q | Users Manual - English - Page 3
first follow the troubleshooting table in the back of the operation manual to inspect and adjust the machine yourself. If the problem persists, please consult your local authorized Brother dealer. Use this machine only for its intended use as described in this manual. Use accessories recommended by - Brother International NX-650Q | Users Manual - English - Page 4
the plug supplied with this equipment, you should contact your authorized dealer to obtain the correct lead. FOR USERS IN AUSTRALIA AND NEW ZEALAND This sewing machine is not intended to be used by young children, and assistance may be required if used by a person with a disability. 3 - Brother International NX-650Q | Users Manual - English - Page 5
Instructions 1 Introduction ...7 Sewing Machine Features ...7 Accessories ...8 Included accessories ...8 Optional accessories ...9 Names of Machine the upper thread ...28 Threading the needle ...31 Threading the needle manually (without using the needle threader 33 Using the twin needle ...33 - Brother International NX-650Q | Users Manual - English - Page 6
and lowering of the presser foot 65 Useful Sewing Tips ...66 Trial sewing ...66 Changing the sewing direction ...66 Sewing curves ...66 Sewing thick fabrics ...67 Sewing thin fabrics...67 Sewing stretch fabrics...67 Sewing leathers or vinyl fabrics ...68 Sewing an even seam allowance ...68 UTILITY - Brother International NX-650Q | Users Manual - English - Page 7
(crazy quilt) stitching ...102 Piecing ...102 Quilting ...104 Free-motion quilting...105 Satin stitching using the sewing speed controller 144 Care and Maintenance ...149 Cleaning the machine surface ...149 Cleaning the race ...149 Troubleshooting ...151 Error messages ...155 Nothing appears in - Brother International NX-650Q | Users Manual - English - Page 8
Thank you for purchasing this sewing machine. Before using this sewing machine, carefully read the "Important Safety Instructions" (page 1), and then study this manual for the correct operation of the various functions. In addition, after you have finished reading this manual, store it where it can - Brother International NX-650Q | Users Manual - English - Page 9
z Foot controller: Model N5V This foot controller can be used on this machine model NX-650. z The screw for the presser foot holder is available through your authorized dealer. (Part code: XA4813-051) z The organized accessory tray is available through your authorized dealer. (Part code: XC4489-051 - Brother International NX-650Q | Users Manual - English - Page 10
(on machine) XC3021 accessories. 1. 2. 1. Wide table Part code: SA551, WT5(XC9567-152) 2. 1/4 inch quilting foot with guide Part code: SA185, F057(XC7416-252) Memo z To obtain optional accessories or parts, contact your sales representative or the nearest authorized service center. Accessories - Brother International NX-650Q | Users Manual - English - Page 11
. d Bobbin winding thread guide and pretension disk Pass the thread under this thread guide and around the pretension disk sewing machine. (page 12) 8 j Flat bed attachment with accessory compartment Store presser feet and bobbins in the accessory compartment of the flat bed attachment. When sewing - Brother International NX-650Q | Users Manual - English - Page 12
thread guide Pass the upper thread through the needle bar thread guide. d Needle plate The needle plate is marked with guides to help sew straight cover the air vent while the sewing machine is being used. e Main power switch Use the main power switch to turn the sewing machine ON and OFF. f Foot - Brother International NX-650Q | Users Manual - English - Page 13
The button lights up in green, red or orange, depending on how the sewing machine is being operated. Green: When the machine is ready to start sewing or while it is sewing Red: When the machine is not ready to start sewing Orange: When the bobbin winder shaft is moved to the right for winding - Brother International NX-650Q | Users Manual - English - Page 14
key is pressed, the font switches to one of the three available. n Manual memory key Press this key to save the adjusted thread tension and stitch width patterns, such as combined patterns and My Custom Stitch patterns, in the sewing machine's memory. q OK key Press this key to apply the selection - Brother International NX-650Q | Users Manual - English - Page 15
14 - Brother International NX-650Q | Users Manual - English - Page 16
sew are described in this chapter. TTurning the Machine On/Off 16 Power supply precautions 16 Turning on the machine 17 Turning off the machine 17 Understanding the LCD Screens 18 Changing the Machine Threading the needle 31 Threading the needle manually (without using the needle threader 33 - Brother International NX-650Q | Users Manual - English - Page 17
On/Off This section explains how to turn the sewing machine on and off. Power supply precautions Be sure to . ● Do not touch the plug with wet hands. Electric shock may result. ● When unplugging the machine, always turn off the main power first. Always grasp the plug to remove it from the outlet. - Brother International NX-650Q | Users Manual - English - Page 18
Prepare the included power cord. When you are finished using the sewing machine, Make sure that the sewing machine is turned turn it off. In addition, before transporting the sewing machine to another location, be sure to turn it off. 1 a off (the main power switch is set to " "), and then - Brother International NX-650Q | Users Manual - English - Page 19
, displays the settings for the selected stitch and error messages if operations are performed incorrectly.When the sewing machine is turned on, the LCD comes on and the following screen appears. 1 3 2 4 5 6 a Presser foot that should be used b Stitch mode c Selected stitch d Stitch length - Brother International NX-650Q | Users Manual - English - Page 20
the settings Press or (Stitch length keys) until the 1 c stitch or machine attribute that you wish to set The general procedure for changing machine settings is described below. is displayed. Turn on the sewing machine. a 1 a Stitch length keys X The LCD comes on. Press b panel. (Settings - Brother International NX-650Q | Users Manual - English - Page 21
density of the stitching. page 126 Select the straight stitch that is automatically selected when the machine is turned on. Allows the stitch width to be adjusted with the sewing speed controller. Allows the language used in the screens to be changed. Specifies whether or not a beep is sounded - Brother International NX-650Q | Users Manual - English - Page 22
screen appears again. X The language of the screens is changed. Press c key). (OK key) or (Cancel/clear X The initial stitch screen appears again. Changing the Machine Settings 21 - Brother International NX-650Q | Users Manual - English - Page 23
. Use of any other bobbin may result in injuries or damage to the machine. ● The included bobbin was designed specifically for this sewing machine. If bobbins from other models are used, the machine will not operate correctly. Use only the included bobbin or bobbins of the same type (part code - Brother International NX-650Q | Users Manual - English - Page 24
Turn on the sewing machine. a Place the spool of thread for the bobbin onto f the spool pin. Slide the spool onto the pin so that the spool is horizontal and - Brother International NX-650Q | Users Manual - English - Page 25
z When sewing with fine, cross-wound thread, use the small spool cap, and leave a small space between the cap and the spool. c b While holding the thread near the spool with h your right hand, as shown, pull the thread with your left hand, and then pass the thread behind the thread guide cover - Brother International NX-650Q | Users Manual - English - Page 26
winder shaft. a Sewing speed controller Press n ("Start/Stop" button) once. Pass the end of the thread through the guide l slit in the button) once to stop the machine. CAUTION ● When the bobbin winding becomes slow, stop the machine, otherwise the sewing machine may be damaged. Use scissors to - Brother International NX-650Q | Users Manual - English - Page 27
bobbin into the bobbin case so that d the thread unrolls to the left. ● The bobbin was designed specifically for this sewing machine. If bobbins from other models are used, the machine will not operate correctly. Use only the included bobbin or bobbins of the same type (part code: SA156, SFB(XA5539 - Brother International NX-650Q | Users Manual - English - Page 28
case. Be sure to thread the machine as indicated. The marks around the bobbin case down the bobbin with your right e hand, and then guide the thread as shown with your left hand. Reattach the sewing without pulling up the bobbin thread. If you wish to pull up the bobbin thread before starting to sew, - Brother International NX-650Q | Users Manual - English - Page 29
thread, carefully follow the instructions. If the upper threading is not correct, the thread may become tangled and the needle may bend or break. Threading the upper thread Set the spool of thread on the spool pin, and then thread the machine. Turn on the sewing machine. a Memo z The order that - Brother International NX-650Q | Users Manual - English - Page 30
presser b foot. Remove the spool cap that is inserted onto the e spool pin. a a Presser foot lever Note z If the presser foot is not raised, the sewing machine cannot be threaded. 1 1 2 a Spool pin b Spool cap Place the spool of thread onto the spool pin. f Slide the spool onto the pin so that - Brother International NX-650Q | Users Manual - English - Page 31
right hand to lightly hold the j thread passed under the thread guide plate, pass the thread through the thread path in the order shown below. 1 a Shutter Note z If the presser foot has been lowered and the shutter is closed, the machine cannot be threaded. Be sure to raise the presser foot and - Brother International NX-650Q | Users Manual - English - Page 32
with sewing machine needles 75/11 through 100/16. z Thread with a thickness of 130/20 or thicker cannot be used with the needle threader. z The needle threader cannot be used with the wing needle or the twin needle. z If the needle threader cannot be used, refer to "Threading the needle manually - Brother International NX-650Q | Users Manual - English - Page 33
pull out about 5 cm (2 inches) of thread toward the rear of the machine. a Needle threader lever X The thread is passed through the eye of the upper threading and the lower threading are finished, you are ready to begin sewing. Note z If the needle is not raised, the needle threader cannot thread - Brother International NX-650Q | Users Manual - English - Page 34
the machine to the needle bar thread a guide. Manually thread the left needle with the upper c thread. Pass the thread through the eye of the needle from the front. • The needle threader cannot be used with the twin needle. If the needle threader is used with the twin needle, the sewing machine - Brother International NX-650Q | Users Manual - English - Page 35
page 28). Without passing the thread through the needle h bar thread guide, manually thread the right needle. Pass the thread through the eye of the needle. If the needle threader is used with the twin needle, the sewing machine may be damaged. Attach zigzag foot "J". i • For details on changing - Brother International NX-650Q | Users Manual - English - Page 36
press (Needle mode selection key) until the key is no longer lit. • Even after the sewing machine is turned off, the twin needle setting is not cancelled. CAUTION ● When changing the sewing direction, press ("Needle Position" button) to raise the needle from the fabric, and then raise the presser - Brother International NX-650Q | Users Manual - English - Page 37
up the bobbin thread When making gathers or before free-motion quilting, first pull up the bobbin thread as described below. (4-5 inches) of the e bobbin thread under the presser foot toward the rear of the machine. Pass the bobbin thread through the slot. b Do not cut the thread with the cutter - Brother International NX-650Q | Users Manual - English - Page 38
breaks and fragments are dispersed. Be sure to read and carefully follow the instructions below. CAUTION ● Only use home sewing machine needles. Use of any other needle may bend the needle or damage the machine. ● Never use bent needles. Bent needles can easily break, possibly resulting in injuries - Brother International NX-650Q | Users Manual - English - Page 39
to 100/16 needle with transparent nylon threads, regardless of the fabric being sewn. z A 75/11 needle is already installed when the sewing machine is purchased. CAUTION ● The appropriate fabric, thread and needle combinations are shown in the table above. If the combination of the fabric, thread - Brother International NX-650Q | Users Manual - English - Page 40
needle Replacing the needle Sewing with a bent needle is extremely dangerous Replace the needle as described below. Use the since the needle may break while the machine is being operated. screwdriver and a needle that has been determined to be straight according to the instructions in "Checking - Brother International NX-650Q | Users Manual - English - Page 41
needle. 1 2 a Screwdriver b Needle clamp screw • Do not apply a strong force when loosening or tightening the needle clamp screw, otherwise certain parts of the sewing machine may be damaged. Install the twin needle in the same way. CAUTION ● Be sure to insert the needle until it touches the needle - Brother International NX-650Q | Users Manual - English - Page 42
presser foot, causing the needle to bend or break. ● Only use presser feet designed specifically for this sewing machine. Use of any other presser foot may result in injuries or damage to the machine. Replace the presser foot as described below. For details on using the side cutter "S", refer to - Brother International NX-650Q | Users Manual - English - Page 43
be used appears in the screen. Check that the correct presser foot is attached before starting to sew. If the wrong presser foot is installed, turn off the sewing machine, attach the correct presser foot, and then select the desired stitch again. Buttonhole foot "A" Overcasting foot "G" Zigzag - Brother International NX-650Q | Users Manual - English - Page 44
machine or when installing a presser foot that adjusted. For best results, increase the pressure when does not use the presser foot holder, such as the sewing thin fabrics, and decrease the pressure when quilting foot. Use the screwdriver to remove the sewing thick fabrics. presser foot holder - Brother International NX-650Q | Users Manual - English - Page 45
when sewing fabrics that are hard to feed such as vinyl and leather and when sewing fabrics that easily slip such as velvets or when quilting. . a "Needle Position" button X The needle is raised. Turn off the sewing machine. b a a Presser foot holder screw 44 Raise the presser foot lever. - Brother International NX-650Q | Users Manual - English - Page 46
With a screwdriver, loosen the presser foot d holder screw, and then remove the walking foot. 1 a a Presser foot holder screw Attach the presser foot holder. e • For details, refer to "Removing the presser foot holder" (page 43). Memo z Only the straight stitch (with reinforcement stitching) and - Brother International NX-650Q | Users Manual - English - Page 47
the wide table level, fully slide it into place. The lower right corner section of the wide table extends over the front section of the sewing machine bed. b a a Lower right corner b Sewing machine bed Note z The optional wide table is available through your brother dealer. 46 - Brother International NX-650Q | Users Manual - English - Page 48
original position. Memo z With the legs folded up, the wide table can 1 be stored attached to the hard case. CAUTION ● Do not move the sewing machine while the wide table is attached, otherwise damage or injuries may occur. When you are finished using the wide table, e remove it. While slightly - Brother International NX-650Q | Users Manual - English - Page 49
GETTING READY 48 - Brother International NX-650Q | Users Manual - English - Page 50
Length 59 Adjusting the stitch width 59 Adjusting the stitch length 60 Useful Functions...61 Changing the needle stop position 61 Automatically sewing reverse/reinforcement stitches 61 Automatically cutting the thread 63 Saving stitch settings 64 Hands-free raising and lowering of the presser - Brother International NX-650Q | Users Manual - English - Page 51
pins, otherwise the needle may break or bend. General sewing procedure Follow the basic procedures below to sew. 1 Turn on the machine. Turn on the sewing machine.For details on turning on the machine, refer to "Turning on the machine" (page 17). ↓ 2 Select the stitch. Select the stitch - Brother International NX-650Q | Users Manual - English - Page 52
fabric pieces are sewn in the correct order and that the right and wrong sides of the fabric are aligned correctly. Turn on the sewing machine. a 2 The straight stitch (left needle position) is automatically selected. Press ("Needle Position" button) once or b twice to raise the needle. Lower the - Brother International NX-650Q | Users Manual - English - Page 53
Press b ("Start/Stop" button) once. Once you are ready to start sewing, you can start the sewing machine. The sewing speed can be adjusted using either the sewing speed controller or the foot controller. Note Important: z When the foot controller is plugged in, ("Start/Stop" button) cannot be used - Brother International NX-650Q | Users Manual - English - Page 54
: Model N5V This foot controller can be used on this machine model NX-650. Turn on the sewing machine. c Faster • Slowly press down on the foot controller. 2 Pressing it down hard starts sewing too quickly. X The machine starts sewing. When the end of the stitching is reached, f completely - Brother International NX-650Q | Users Manual - English - Page 55
lever. 1 Press ("Start/Stop" button) or press down b on the foot controller. At this time, if ("Start/Stop" button) is held down, the machine sews at a low speed. a "Reverse/Reinforcement Stitch" button X While ("Reverse/Reinforcement Stitch" button) is held down, reverse stitches are sewn. After - Brother International NX-650Q | Users Manual - English - Page 56
When you wish to finish the stitching, press a ("Thread Cutter" button) once. X The machine starts sewing in the normal 2 sewing direction. After sewing to the end of the stitching, the i sewing machine stops. Press ("Start/Stop" button) or release foot controller. 1 1 a "Thread Cutter" button - Brother International NX-650Q | Users Manual - English - Page 57
Using the manual thread cutter When sewing with thread thicker than #30, nylon or metallic threads, or other special threads, use the thread cutter on the side of the machine to cut the threads. When you wish to finish the stitching and the a sewing machine is stopped, press ("Needle Position - Brother International NX-650Q | Users Manual - English - Page 58
Adjusting the Thread Tension The tensions of the upper thread and of the bobbin thread (thread tension) should be adjusted so that they are equal. Thread tension ■ Upper thread is too loose If the upper thread is visible from the wrong side of the fabric, the upper thread is too loose. You - Brother International NX-650Q | Users Manual - English - Page 59
thread tension, press (Thread tension key). The tension of the upper thread can be changed using thread tension keys. Turn on the sewing machine. a X The tension of the upper thread is changed. X The LCD comes on. Select a stitch. b X A screen containing settings for the selected stitch appears - Brother International NX-650Q | Users Manual - English - Page 60
). Adjusting the stitch width The stitch width (zigzag width) can be adjusted to make the stitch wider or narrower. Turn on the sewing machine. a 2 - + • If the setting is changed, the highlighted value is erased. X The LCD comes on. Select a stitch. b X A screen containing settings for the - Brother International NX-650Q | Users Manual - English - Page 61
Adjusting the stitch length The stitch length can be adjusted to make the stitch longer or shorter. Turn on the sewing machine. a To make the stitch length shorter, press c (Stitch length key). To make the stitch length longer, press (Stitch length key). X The LCD comes on. Select a - Brother International NX-650Q | Users Manual - English - Page 62
. reinforcement stitches are sewn depends on the stitch that is selected. For details, refer to "Stitch Settings" Turn on the sewing machine. a (page 138). Turn on the sewing machine. a X The LCD comes on. Press (Needle stop position key). b X (Needle stop position key) lights up, and the - Brother International NX-650Q | Users Manual - English - Page 63
reverse/reinforcement stitching off, press (Automatic reverse/ reinforcement stitch key) until the key is no longer lit. • When the sewing machine is turned off, the automatic reverse/reinforcement stitching setting is cancelled. Position the fabric under the presser foot, and d then - Brother International NX-650Q | Users Manual - English - Page 64
stitching. • To turn off programmed thread-cutting, press (Automatic thread cutting key) until the key is no longer lit. • When the sewing machine is turned off, the programmed thread-cutting setting is cancelled. The thread is cut here. Memo z Reverse/reinforcement stitches WILL NOT be sewn - Brother International NX-650Q | Users Manual - English - Page 65
SEWING BASICS Saving stitch settings Adjusted thread tension and stitch width settings, press (Reset key). To use the default settings the next time that the stitch is selected, press (Manual memory key) to save the settings. 1 3 2 a Thread tension keys b Stitch width keys c Stitch length - Brother International NX-650Q | Users Manual - English - Page 66
lower the presser foot with your knee, leaving both hands free to handle the fabric. ■ Using the knee lifter Stop the sewing machine. a • Do not use the knee lifter while the sewing machine is operating. With your knee, press the knee lifter to the b right. Keep the knee lifter pressed to the right - Brother International NX-650Q | Users Manual - English - Page 67
stitching and the number of layers of fabric sewn, perform the trial sewing under the same conditions that will be used with your project. Changing the sewing direction When the stitching reaches a corner, stop the a sewing machine. Leave the needle lowered (in the fabric). If the needle remained up - Brother International NX-650Q | Users Manual - English - Page 68
c level with the seam, allowing the fabric to feed. X Once the trouble spot has been passed, the 2 foot will return to its normal position. with too much force, the needle may bend or break. Sewing thin fabrics When sewing thin fabrics, the stitching may become misaligned or the fabric may - Brother International NX-650Q | Users Manual - English - Page 69
of a seam sewn with the straight stitch (left needle position). Sew while keeping the edge of the fabric aligned with a marking in inch) a Seam b Presser foot ■ Aligning the fabric with the stitch guide foot Sew while keeping the right edge of the fabric aligned with a desired position of markings - Brother International NX-650Q | Users Manual - English - Page 70
98 Elastic attaching 98 Appliqué, Patchwork and Quilt Stitching 100 Appliqué stitching 101 Patchwork (crazy quilt) stitching....... 102 Piecing 102 Quilting 104 Free-motion quilting 105 Satin stitching using the sewing speed controller 106 Reinforcement Stitching 108 Triple stretch - Brother International NX-650Q | Users Manual - English - Page 71
stitches can be selected simply by pressing the key. † Saved patterns Frequently used patterns and combined patterns can be saved on the machine's memory and easily retrieved using (Preset utility stitch/saved pattern key) and the numeric keys. For details, refer to ■ Direct selection "Saving - Brother International NX-650Q | Users Manual - English - Page 72
† Decorative stitches There are two decorative stitch modes: decorative stitch 1 mode and decorative stitch 2 mode . If (Decorative stitch key) is pressed once, decorative stitch 1 mode is selected. If (Decorative stitch key) is pressed twice, decorative stitch 2 mode is selected. Each press - Brother International NX-650Q | Users Manual - English - Page 73
are stored in the accessory compartment. • For details on the stitches that can be sewn with the twin needle, refer to "Stitch Settings" (page 138). Attach the presser foot. c • For details, refer to "Replacing the presser foot" (page 41). Turn on the sewing machine. d ■ With direct selection With - Brother International NX-650Q | Users Manual - English - Page 74
Press the key assigned with the stitch to select b the stitch. • Continue with step f (on page 74). ■ With number selection There are three modes of stitches that can be selected by number: utility stitch mode , decorative stitch mode and character stitch mode . In addition, there are two - Brother International NX-650Q | Users Manual - English - Page 75
that should be used appears in the screen. Check that the correct presser foot is attached before starting to sew. If the wrong presser foot is installed, turn off the sewing machine, attach the correct presser foot, and then select the desired stitch again. ■ To select a different stitch Check the - Brother International NX-650Q | Users Manual - English - Page 76
• To erase the stitch and select a different one, press (OK key), and then change the stitch mode. • To stop the current stitch from being erased, press (Cancel/clear key) to return to the previous screen. Memo z After changing stitch settings such as the stitch length and width or after - Brother International NX-650Q | Users Manual - English - Page 77
16) Stitch Length [mm (inch)] Auto Manual 2.0 1.0-4.0 (1/16) (1/16-3/16) 2.5 1.0-4.0 (3/32) (1/16-3/16) 2.5 1.0-4.0 (3/32) (1/16-3/16) Presser Foot G Attach overcasting foot "G". a G Sew with the edge of the fabric against the d presser foot guide. 1 • For details, refer to "Replacing the - Brother International NX-650Q | Users Manual - English - Page 78
using zigzag foot "J" Seven stitches can be used to sew overcasting stitches with zigzag foot "J". Pattern Numeric Stitch Name Key Application Stitch Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual Presser Foot Zigzag stitch (center 07 needle position) Preventing - Brother International NX-650Q | Users Manual - English - Page 79
the presser foot" (page 41). Lower the presser foot lever, and then b manually thread the needle. • The needle threader cannot be used. If the needle threader is used with the side cutter, the sewing machine may be damaged. Raise the presser foot lever. c b a Connecting fork b Needle clamp - Brother International NX-650Q | Users Manual - English - Page 80
under the side cutter, g and then pull it out toward the rear of the sewing machine. Position the fabric in the side cutter. j The cut in the fabric should be positioned over the guide plate of the side cutter. a a Guide plate • If the fabric is not positioned correctly, the fabric will not be cut - Brother International NX-650Q | Users Manual - English - Page 81
gathers or pintucks (center baseline/reverse stitching) 3.5 0.0-7.0 (1/8) (0-1/4) Reinforcing seams and sewing stretch fabrics 0.0 0.0-7.0 (0) (0-1/4) Stitch Length [mm (inch)] Auto Manual Presser Foot 20 5-30 (3/4) (3/16-1-3/16) 2.5 0.2-5.0 (3/32) (1/64-3/16) 2.5 0.2-5.0 (3/32) (1/64 - Brother International NX-650Q | Users Manual - English - Page 82
12 mm (1/2 inch). If the stitch width is changed (between 0 and 7.0 mm (1/4 inch)), the needle position will also change. By changing the stitch width and sewing with the right side of the presser foot aligned with the edge of the fabric, a seam allowance can be sewn with a fixed width - Brother International NX-650Q | Users Manual - English - Page 83
Manual 00 (0) 3← - 3→ 00 (0) 3← - 3→ Stitch Length [mm (inch)] Auto Manual 2.0 1.0-3.5 (1/16) (1/16-1/8) 2.0 1.0-3.5 (1/16) (1/16-1/8) Presser Foot R Sew fabric with the edge of the folded e hem against the guide of the presser foot, and then lower the presser foot lever. 1 3 2 a - Brother International NX-650Q | Users Manual - English - Page 84
. Press (of the Stitch width keys) to decrease the stitch width so that the needle slightly catches the fold of the hem. Sew with the fold of the hem against the g presser foot guide. Remove the basting stitching. h 1 2 a Wrong side of fabric b Right side of fabric Memo z For best results when - Brother International NX-650Q | Users Manual - English - Page 85
on. Eleven stitches are available for sewing one-step buttonholes and one stitch for sewing on buttons. Stitch Name Pattern 3.0-5.0 (3/16) (1/8-3/16) 5.0 3.0-5.0 (3/16) (1/8-3/16) Stitch Length [mm (inch)] Auto Manual 0.4 0.2-1.0 (1/64) (1/64-1/16) 0.4 0.2-1.0 (1/64) (1/64-1/16) 0.4 0.2-1.0 (1/64 - Brother International NX-650Q | Users Manual - English - Page 86
stitching The names of parts of buttonhole foot "A", which is used for sewing buttonholes, are indicated below. Use chalk to mark on the fabric the Button guide plate b Presser foot scale c Pin d Marks on buttonhole foot e 5 mm (3/16 inch) 1 a Marks on fabric Pull out the button guide plate - Brother International NX-650Q | Users Manual - English - Page 87
+ thickness of button) c 5 mm (3/16 inch) Example: For a button with a diameter of 15 mm (9/16 inch) and a thickness of 10 mm (3/8 inch), the button guide plate should be set to 25 mm (1 inch) on the scale. 1 A 2 a Mark on fabric b Red marks on buttonhole foot Pass the upper thread down through - Brother International NX-650Q | Users Manual - English - Page 88
Gently hold the end of the upper thread in g your left hand, and then start sewing. 1 X Once sewing is completed, the machine automatically sews reinforcement stitches, then stops. a Eyelet punch • When using the eyelet punch, place thick paper or some other protective sheet under the fabric - Brother International NX-650Q | Users Manual - English - Page 89
Adjust the stitch width to the thickness of the d gimp thread. Lower the presser foot lever and the e buttonhole lever, and then start sewing. When sewing is finished, gently pull the gimp f thread to remove any slack. • For details, refer to "Adjusting the stitch width" (page 59). Memo z Before - Brother International NX-650Q | Users Manual - English - Page 90
refer to "Selecting stitching" (page 72). • Since the end of the thread will be tied off later, do not set the sewing machine for programmed-thread cutting. CAUTION ● When sewing, be sure that the needle does not touch the button, otherwise the needle may bend or break. Buttonhole Stitching/Button - Brother International NX-650Q | Users Manual - English - Page 91
the thread by hand. This attaches the button securely. Place the button into button-sewing foot "M", a and then pull the shank lever toward you. 1 X The sewing machine automatically stops after sewing reinforcement stitches. • If additional strength is needed to secure the button, perform the - Brother International NX-650Q | Users Manual - English - Page 92
Key Application Straight stitch (center 03 needle position) Attaching zippers Sewing concealed seams and pintucks Stitch Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual Presser Foot 3.5 0.0-7.0 2.5 0.2-5.0 I (1/8) (0-1/4) (3/32) (1/64-3/16) There are many methods - Brother International NX-650Q | Users Manual - English - Page 93
the needle hits the presser foot, the needle may bend or break. 4 a Stitching b Right side of fabric c Basting stitching d End of zipper opening CAUTION ● When sewing, be sure that the needle does not touch the zipper, otherwise the needle may bend or break. Remove the basting stitching. h 92 - Brother International NX-650Q | Users Manual - English - Page 94
edge of e the fabric having the extra 3 mm (1/8 inch), and then baste or pin the zipper in place. Using a basting stitch, continue sewing to the b edge of the fabric. 2 1 1 3 2 4 a Basting stitching b Reverse stitches c Wrong side of fabric d End of zipper opening a Zipper teeth b Basting - Brother International NX-650Q | Users Manual - English - Page 95
may bend or break. When you are about 5 cm (2 inches) from the i end of the zipper, stop the sewing machine with the needle lowered (in the fabric), raise the presser foot lever, and then open the zipper and continue sewing. a Pin on the left side b Needle drop point Topstitch around the zipper - Brother International NX-650Q | Users Manual - English - Page 96
When you are about 5 cm (2 inches) from the m end of the zipper, stop the sewing machine with the needle lowered (in the fabric), raise the presser foot lever, and then open the zipper and continue sewing. Remove the basting stitching. n 3 Zipper Insertion 95 - Brother International NX-650Q | Users Manual - English - Page 97
Name Key Application Straight stitch 01 (left needle position) Attaching zippers Sewing concealed seams and piping Stitch Width [mm (inch)] Auto Manual 0.0 0.0-7.0 (0) (0-1/4) Stitch Length [mm (inch)] Auto Manual Presser Foot 2.5 0.2-5.0 (3/32) (1/64-3/16) There are many methods for - Brother International NX-650Q | Users Manual - English - Page 98
c Fabric Refer to the steps of attaching the adjustable 3 b zipper/piping foot (page 96). Sew along the piping. c 4 a Stitching b Right side of fabric c Basting stitching d End of zipper opening CAUTION ● When sewing, be sure that the needle does not touch the zipper, otherwise the needle may - Brother International NX-650Q | Users Manual - English - Page 99
stretch fabrics Stitch Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual Presser Foot 1.0 1.0-3.0 2.5 1.0-4.0 (1/16) 05 . b • For details, refer to "Selecting stitching" (page 72). Sew the fabric without stretching it. c Elastic attaching When elastic tape is attached to the - Brother International NX-650Q | Users Manual - English - Page 100
Attach zigzag foot "J". b J • For details, refer to "Replacing the presser foot" (page 41). Select a stitch. c • For details, refer to "Selecting stitching" (page 72). Sew the elastic tape to the fabric while d stretching the tape so that it is the same length as the fabric. While pulling the - Brother International NX-650Q | Users Manual - English - Page 101
can be used for sewing appliqués, patchwork and quilts are described below. Pattern Numeric Stitch Name Key Application 07 Zigzag stitch 24 Attaching appliqués (center baseline/ reverse stitching) Appliqué quilting, - free-motion quilting, satin stitching Stitch Width [mm (inch)] Auto Manual - Brother International NX-650Q | Users Manual - English - Page 102
72). Turn the handwheel toward you f (counterclockwise), and then begin sewing a Seam allowance around the edge of the appliqué, making sure 3 it will be attached to. 1 a Basting stitching When sewing around corners, stop the machine with the needle in the fabric just outside of the appliqu - Brother International NX-650Q | Users Manual - English - Page 103
quilt) stitching Fold the edge of the top piece of fabric and a place it over the lower piece. Sew the two pieces of fabric together so the b pattern spans over both pieces. Piecing Sewing For details, refer to "Selecting stitching" (page 72). Sew with the side of the presser foot aligned d with - Brother International NX-650Q | Users Manual - English - Page 104
presser foot" (page 41). Select stitch 03 . c 1 a Seam (3.2 mm (1/8 inch)) Start sewing. e When the end of the stitching is reached, stop f the sewing machine. Sew until the mark at the lower edge of the 1/4 inch quilting foot aligns with the lower edge of the fabric. 1 2 3 a 6.4mm (1/4 inch) b End - Brother International NX-650Q | Users Manual - English - Page 105
and bottom layers of fabric is called "quilting". Quilts can easily be sewn using the walking foot and the quilting guide. ■ Using the quilting guide Use the quilting guide to sew parallel stitches that are equally spaced. Baste the fabric to be quilted. a Attach the walking foot. b • For details - Brother International NX-650Q | Users Manual - English - Page 106
foot X The feed dogs are lowered. a holder. Turn on the sewing machine, and then select a e stitch. • Refer to "Removing the presser foot holder" (page 43). • For details, refer to "Selecting stitching" (page 3 72). Secure the quilting foot with the presser foot b holder screw. The pin on - Brother International NX-650Q | Users Manual - English - Page 107
keys) to select , press or (Stitch Attach zigzag foot "J". b J • For details, refer to "Replacing the presser foot" (page 41). Turn on the sewing machine, and then press c (Settings key) in the operation panel. X The settings screen appears. Press or (Stitch length keys) until d is displayed - Brother International NX-650Q | Users Manual - English - Page 108
When you are finished sewing, set the stitch i width control setting back to OFF. Memo z Although the stitching result differs depending on the type of used, for best results, adjust the stitch length to between 0.3 and 0.5 mm (1/64 and 1/32 inch). 3 Appliqué, Patchwork and Quilt Stitching 107 - Brother International NX-650Q | Users Manual - English - Page 109
Stitch Name Key Application Stitch Width [mm (inch)] Auto Manual Triple stretch 04 stitch Reinforcing the seams of sleeves and page 72). Start sewing. c • For details, refer to "Starting to sew" (page 52). Determine the desired length of the bar tack. a Set the button guide plate on buttonhole - Brother International NX-650Q | Users Manual - English - Page 110
lever b Bracket Gently hold the end of the upper thread in f your left hand, and then start sewing. a a Do not reduce the gap. X Once sewing is completed, the machine automatically sews reinforcement stitches, then stops. Cut the threads, raise the presser foot lever, g and then remove the fabric - Brother International NX-650Q | Users Manual - English - Page 111
torn can be darned. Darning is sewn as shown below. 1 1 a Reinforcement stitching Determine the desired length of the darning. a Set the button guide plate on buttonhole foot "A" to the desired length. (The distance between the markings on the presser foot scale is 5 mm (3/16 inch).) 1 Position - Brother International NX-650Q | Users Manual - English - Page 112
3 2 a Buttonhole lever b Bracket Gently hold the end of the upper thread in f your left hand, and then start sewing. X Once sewing is completed, the machine automatically sews reinforcement stitches, then stops. Cut the threads, raise the presser foot lever, g and then remove the fabric. Raise the - Brother International NX-650Q | Users Manual - English - Page 113
[mm (inch)] Auto Manual 7.0, 6.0 or 7.0 5.0 (1/4) (1/4, 15/64 or 3/16) Stitch Length [mm (inch)] Auto Manual - - Presser Foot then lower the presser foot lever. Start sewing. e X Once sewing is completed, the machine automatically sews reinforcement stitches, then stops. Use the eyelet - Brother International NX-650Q | Users Manual - English - Page 114
the presser foot" (page 41). X The fabric is fed toward the back of the machine, as usual. After you have sewn to the corner, stop the e sewing machine, and then select stitch 68 . Start sewing. f Select stitch 01 . c • For details, refer to "Selecting stitching" (page 72). X The fabric is - Brother International NX-650Q | Users Manual - English - Page 115
to the corner, stop the k sewing machine, and then select stitch 01 again. After sewing 3 to 5 stitches at the beginning of l the stitching, stop the sewing machine. Memo z The feeding direction of the fabric differs depending on the stitch that is selected. Be sure to guide the fabric while it is - Brother International NX-650Q | Users Manual - English - Page 116
Stitching Various decorative stitches can be sewn with this sewing machine. Pattern Stitch Name Application 32 Fagoting stitch 33 Sewing two pieces of fabric together across an open seam Stitch Width [mm (inch)] Auto Manual 5.0 0.0-7.0 (3/16) (0-1/4) Stitch Length [mm (inch)] Auto - Brother International NX-650Q | Users Manual - English - Page 117
a line down the middle of the thin paper or water-soluble stabilizer, sewing is easier. 3 Stitch Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual Presser Foot 6.0 1.5-7.0 1.6 1.0-4.0 (15/64) (1/16-1/4) (1/16) (1/16-3/16) N 5.0 1.5-7.0 1.6 1.0-4.0 (3/16) (1/16-1/4) (1/16) (1/16 - Brother International NX-650Q | Users Manual - English - Page 118
a hot iron before it is sewn. Trim along the stitches. d • Be careful not to cut the stitches. a 1 cm (3/8 inch) • It is not necessary to sew reverse/ reinforcement stitches or cut the thread. • At the end of the stitching, the thread is pulled out about 5 cm (2 inches). Pull the bobbin threads - Brother International NX-650Q | Users Manual - English - Page 119
72). Stitch between the straight stitches. f Select stitch 20 c thread tension. , and then increase the • For details, refer to "Selecting stitching" (page 72). Sew while making sure that the needle drops d slightly off the edge of the fabric. 1 Pull out the threads for the straight stitches - Brother International NX-650Q | Users Manual - English - Page 120
fabrics. This is used when making a crazy quilt. Attach zigzag foot "J". a When sewing with the wing needle, the needle holes are needle threader cannot be used with the wing needle, otherwise the sewing machine may be damaged. Manually pass the thread through the eye of the needle from the front - Brother International NX-650Q | Users Manual - English - Page 121
are described below. ■ Drawnwork (Example 1) • For details, refer to "Selecting stitching" (page 72). With the right side of the fabric facing up, sew d along the right edge of the frayed section. N Press e panel. (Settings key) in the operation X The settings screen appears. Press or (Stitch - Brother International NX-650Q | Users Manual - English - Page 122
threads from two sections of a the fabric, separated by an unfrayed section of about 4 mm (3/16 inch). 3 1 a 4 mm (3/16 inch) Attach monogramming foot "N". b Sew along the other edge of the frayed section i so that it looks like the previous stitching. N Set the mirror image pattern setting back to - Brother International NX-650Q | Users Manual - English - Page 123
threads When sewing thin, medium weight or stretch fabrics, use the ball point needle. When sewing thick fabrics, use a 90/14 home sewing machine needle. In achieved. Be sure to sew a trial piece of fabric before sewing your project. In addition, while sewing, be sure to guide the fabric with your - Brother International NX-650Q | Users Manual - English - Page 124
X The order that the patterns appear in the LCD is the order that they will be sewn. 3 • When the sewing is started, the selected pattern is sewn repeatedly until the sewing machine is stopped. Select the next pattern. b Use the numeric keys to type in the number for the desired stitch. To - Brother International NX-650Q | Users Manual - English - Page 125
is displayed. X The screen for specifying repeat sewing appears. a Single b Repeated Note z If repeated sewing is set, the pattern is repeatedly sewn until the sewing machine is stopped. z If the sewing machine is turned off, the repeated/single sewing setting returns to its default setting. Press - Brother International NX-650Q | Users Manual - English - Page 126
) or (Cancel/clear X The initial stitch screen appears again. Press or (Stitch length keys) until c is displayed. X The screen for changing the pattern size appears. Sewing the Various Built-In Decorative Patterns 125 - Brother International NX-650Q | Users Manual - English - Page 127
UTILITY STITCHES Press or (Stitch width keys) until the d desired size is selected. Select for the small size or select for the large size. Changing the stitch density If a decorative satin stitch has been selected, the stitch density can be changed. Select a decorative satin stitch (No. 60-69 - Brother International NX-650Q | Users Manual - English - Page 128
largest setting (×5) is displayed, a beep sounds. X The satin stitch length is changed. Press (OK key) or (Cancel/clear e key). X The initial stitch screen appears again. Sewing the Various Built-In Decorative Patterns 127 - Brother International NX-650Q | Users Manual - English - Page 129
key), and then use the numeric keys to type in "41". Specify that the patterns will be sewn e repeatedly. • For details, refer to "Repeat sewing patterns" (page 124). ■ Examples of step patterns Using the numeric keys, type in "49" to select b (No. 49 of , selected with ). X The next pattern - Brother International NX-650Q | Users Manual - English - Page 130
mirror imaging the pattern appears. Press or d . To return to width keys). (Stitch width keys) to select , press or (Stitch X The pattern is mirror imaged. Sewing the Various Built-In Decorative Patterns 129 - Brother International NX-650Q | Users Manual - English - Page 131
for later use. Since saved patterns are not lost after the sewing machine is turned off, they can be retrieved at any time. This and the initial stitch screen appears again. Note z Do not turn off the sewing machine while a pattern is being saved, otherwise the pattern data may be lost. Press b - Brother International NX-650Q | Users Manual - English - Page 132
(0 through 9) for the b pocket where the pattern is saved. X The saved contents of the pocket for the selected number are retrieved. Start sewing. c X The pattern for making the adjustment is sewn. X The sewing machine stops after it has • If nothing was saved in the selected pocket, a finished - Brother International NX-650Q | Users Manual - English - Page 133
setting. X Make the necessary adjustments according to how the pattern is sewn. Press (Stitch width key) to decrease the adjustment setting. Start sewing again, and then check the pattern. h Continue adjusting the pattern until it is sewn correctly. When the pattern is sewn correctly, press - Brother International NX-650Q | Users Manual - English - Page 134
then link those points with a continuous straight line. Prepare a grid sheet set. Draw a sketch of the pattern on the grid sheet a set. 3 Determine the sewing order. d 98 6 5 10 4 7 11 13 12 3 2 Draw the pattern as one continuous line and with the start point and the end point of the - Brother International NX-650Q | Users Manual - English - Page 135
) to select the vertical coordinate, and then press (OK key). • For details, refer to "Replacing the presser foot" (page 41). Turn on the sewing machine. b Select c ). (No. 99 of , selected with Press (Decorative stitch key), and then use the numeric keys to type in "99". 2 1 a Stitch width - Brother International NX-650Q | Users Manual - English - Page 136
screen where points can be edited so that points can be added or removed. Memo z To save the entered pattern data, save it from the sewing screen. For details, refer to 3 "Saving patterns" (page 130). z The pattern in the LCD will appear different from the pattern drawn in the grid sheet - Brother International NX-650Q | Users Manual - English - Page 137
UTILITY STITCHES Examples of designs Enter each of the points indicated in the table to sew the sample stitch. Point Point 0 0 0 20 38 13 1 12 0 21 35 14 2 18 3 22 32 13 3 22 6 23 30 10 4 23 10 24 32 6 5 21 - Brother International NX-650Q | Users Manual - English - Page 138
in this chapter. Stitch Settings...138 Utility stitches 138 Other stitches 144 Care and Maintenance 149 Cleaning the machine surface 149 Cleaning the race 149 Troubleshooting ...151 Error messages 155 Nothing appears in the LCD 156 Operation beep 156 Cancelling the operation beep 156 - Brother International NX-650Q | Users Manual - English - Page 139
stitch Application Stitch Width [mm (inch)] Stitch Length [mm (inch)] Auto Manual Auto Manual Reverse/ Reinforcement Stitching Programmed Thread-Cutting J Basic stitching, sewing gathers or pintucks, etc. 0.0 (0) 0.0-7.0 2.5 0.2-5.0 Yes (0-1/4) (3/32) (1/64-3/16) (J) Reverse Reverse - Brother International NX-650Q | Users Manual - English - Page 140
[mm (inch)] Stitch Length [mm (inch)] Auto Manual Auto Manual Reverse/ Reinforcement Stitching Programmed Thread-Cutting 11 G Overcasting on 23 looks hand-sewn (for quilting) Zigzag 24 stitch (for quilting) Appliqué 25 stitch (for quilting) Quilting stitch 26 (for stippling) Satin - Brother International NX-650Q | Users Manual - English - Page 141
Auto Manual Reverse/ Reinforcement Stitching Programmed Thread-Cutting J Patchwork stitching and decorative stitching 4.0 (3/16) 0.0-7.0 (0-1/4) 1.2 (1/16) 0.2-4.0 Yes (1/64-3/16) (J) Reinforcement Reinforcement + thread-cutting No Patchwork stitching, J decorative stitching and sewing - Brother International NX-650Q | Users Manual - English - Page 142
Stitch Name Application Stitch Width [mm (inch)] Stitch Length [mm (inch)] Auto Manual Auto Manual Reverse/ Reinforcement Stitching Programmed Thread-Cutting 39 Lace sewing, decorative N hemming, heirloom stitching, etc. 3.5 (1/8) 1.5-7.0 (1/16-1/4) 2.5 (3/32) 1.6-4.0 (1/16-3/16) No - Brother International NX-650Q | Users Manual - English - Page 143
54 55 56 57 58 Darning stitch 59 Bar tack 60 stitch Button- 61 sewing stitch 62 Eyelet stitch Application Stitch Width [mm (inch)] Stitch Length [mm (inch)] Auto Manual Auto Manual Reverse/ Reinforcement Stitching Programmed Thread-Cutting Horizontal buttonholes A on thin and medium - Brother International NX-650Q | Users Manual - English - Page 144
Stitch Name Application Stitch Width [mm (inch)] Stitch Length [mm (inch)] Auto Manual Auto Manual Reverse/ Reinforcement Stitching Programmed Thread-Cutting 63 S Sewing straight stitches while cutting the fabric 0.0 (0) 0.0-2.5 (0-3/32) 2.5 (3/32) 0.2-5.0 (1/64-3/16) No Reinforcement - Brother International NX-650Q | Users Manual - English - Page 145
APPENDIX Other stitches Presser Foot Twin Needle Pattern Size Adjustable Stitching Density Adjustable Pattern Length/width Left/Right Flipping Stitch Type Pattern 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 Large: Decorative stitches 21 22 23 24 25 N 26 27 28 29* 30* No - Brother International NX-650Q | Users Manual - English - Page 146
Presser Foot Twin Needle Pattern Size Adjustable Stitching Density Adjustable Pattern Length/width Left/Right Flipping Stitch Type Pattern 01 02 03 04 05 06 07 11 12 13 16 17 18* 20 21 22 23 24 25 26 Yes J** (*Not possible) Yes (J) 27* 28 29 Utility 08 09 10 decorative stitches 14 15 - Brother International NX-650Q | Users Manual - English - Page 147
APPENDIX Presser Foot Twin Needle Pattern Size Adjustable Stitching Density Adjustable Pattern Length/width Left/Right Flipping Stitch Type Pattern 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 - Brother International NX-650Q | Users Manual - English - Page 148
Presser Foot Twin Needle Pattern Size Adjustable Stitching Density Adjustable Pattern Length/width Left/Right Flipping Stitch Type Pattern 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 - Brother International NX-650Q | Users Manual - English - Page 149
APPENDIX Presser Foot Twin Needle Pattern Size Adjustable Stitching Density Adjustable Pattern Length/width Left/Right Flipping Stitch Type Pattern 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Character 41 42 43 44 - Brother International NX-650Q | Users Manual - English - Page 150
. a Unplug the power cord from the power supply b jack on the right side of the sewing machine. CAUTION ● Unplug the power cord before cleaning the machine, otherwise injuries or an electric shock may occur. a a Needle plate cover X The needle plate cover is removed. ■ If there is no screw in - Brother International NX-650Q | Users Manual - English - Page 151
case that is scratched, otherwise the upper thread may become tangled, the needle may break or sewing performance may suffer. For a new bobbin case (part code: XC3153-151), contact your nearest authorized service center. ● Be sure that the bobbin case is correctly installed, otherwise the needle may - Brother International NX-650Q | Users Manual - English - Page 152
check the following possible problems before requesting service. If the problem persists, contact your dealer or the nearest authorized service center. Symptom Probable Cause Remedy Reference The machine is not turned on. Turn on the machine. page 17 The sewing machine does not operate. The - Brother International NX-650Q | Users Manual - English - Page 153
being used, or the thread has come out of the needle bar thread guide). Correct the upper threading. There are knots or tangles in the thread. . Contact your dealer or the nearest authorized service center. A bobbin designed specifically for this machine is not used. Incorrect bobbins will not - Brother International NX-650Q | Users Manual - English - Page 154
this machine is not used. Incorrect bobbins will not work properly. Only use a bobbin designed specifically for this machine. being sewn, the stitch is too long. Shorten the stitch length or sew with stabilizer material under the fabric. page 60 The thread tension is Troubleshooting 153 - Brother International NX-650Q | Users Manual - English - Page 155
feed lever to the right. (as seen from the rear of the machine) The stitch is too short. Lengthen the stitch length. The fabric does clean the race. The sewing lamp does not come on. The sewing lamp is damaged. Contact your dealer or the nearest authorized service center. Nothing appears in - Brother International NX-650Q | Users Manual - English - Page 156
Stop" button) is pressed before the sewing machine is correctly set up or if an operation is performed incorrectly, an error message appears in the LCD. Follow the instructions that appear. The message will disappear thread is tangled. The bobbin winder is winding the bobbin. Troubleshooting 155 - Brother International NX-650Q | Users Manual - English - Page 157
of the LCD is either too light or too dark. If this is the case, perform the following operation. Turn off the sewing machine. a Cancelling the operation beep When the sewing machine is purchased, it is set to beep each time an operation panel key is pressed. This setting can be changed so that - Brother International NX-650Q | Users Manual - English - Page 158
Press or d . To return to keys). (Stitch width keys) to select , press or (Stitch width X The machine is now set so that it will not beep. Press (Cancel/clear key) or (OK e key). X The initial stitch screen appears again. 4 Troubleshooting 157 - Brother International NX-650Q | Users Manual - English - Page 159
quilting foot 9 103 1/4 inch quilting foot with guide 9 2-point zigzag stitch 77 3-point zigzag stitch 77 A accessories 8 accessory stitching 84 C cancel/clear key 13 care 149 changing machine settings 19 changing sewing direction 66 changing the settings 19 character stitch key 13 - Brother International NX-650Q | Users Manual - English - Page 160
43 programmed thread-cutting 63 machine settings 19 , main power switch 11 17 Q maintenance 149 quick reference guide 9 manual memory key 13 quilting 104 memory key 13 , quilting foot 9 105 mirror image 129 monogramming foot 9 , quilting guide 9 104 4 , My Custom Stitch 71 - Brother International NX-650Q | Users Manual - English - Page 161
10 56 , thread cutter button 12 55 thread guide cover 10 thread guide disk 11 thread guide plate 10 thread tension 58 , thread tension ajustment 57 58 thread tension keys 13 top cover 10 trial sewing 66 triple stretch stitch 108 troubleshooting 151 twin needle 9, 33, 40 U upper thread - Brother International NX-650Q | Users Manual - English - Page 162
English 885-U24 XE0371-001 Printed in China
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
 |
 |
Computerized Sewing Machine
Operation
Manual
Read before use.
Read when additional
information is required.
GETTING READY
SEWING BASICS
UTILITY STITCHES
APPENDIX