Brother International PE-700II Users Manual - English

Brother International PE-700II Manual

Get Brother International PE-700II PDF manuals and user guides View all Brother International PE-700II manuals
Add to My Manuals
Save this manual to your list of manuals

Brother International PE-700II manual content summary:

  • Brother International PE-700II | Users Manual - English - Page 1
    GETTING READY EMBROIDERY APPENDIX Computerized Embroidery Machine Operation Manual
  • Brother International PE-700II | Users Manual - English - Page 2
    instruction manual. • To unplug the machine, switch the machine Return the machine to the nearest authorized dealer or service center for needle. Do not use bent or damaged needles. • Keep fingers away from all moving parts. Special care is required around the machine needle. • Switch the machine
  • Brother International PE-700II | Users Manual - English - Page 3
    troubleshooting table in the back of the operation manual to inspect and adjust the machine yourself. If the problem persists, please consult your local authorized Brother dealer. Use this machine only for its intended use as described in the manual. Use accessories This embroidery machine is not
  • Brother International PE-700II | Users Manual - English - Page 4
    Contents Important Safety Instructions 1 Introduction ...5 Machine Features ...5 Accessories...6 Included accessories ...6 Optional accessories ...7 Names of Machine Parts and Their Functions 8 Front view ...8 Needle and embroidery foot section ...9 Right-side/rear view ...9 Operation buttons
  • Brother International PE-700II | Users Manual - English - Page 5
    65 Thread runs out partway through a design...65 Stopping while embroidering ...66 APPENDIX 69 Care and Maintenance ...70 Cleaning the machine surface ...70 Cleaning the race ...70 Attaching the Embroidery Foot 72 Attaching the embroidery Foot "Q" ...72 Troubleshooting ...74 Error messages ...78
  • Brother International PE-700II | Users Manual - English - Page 6
    Thank you for purchasing this embroidery machine. Before using the machine, carefully read the "Important Safety Instructions" (page 1), and then study this manual for the correct operation of the various functions. In addition, after you have finished reading this manual, store it where it can
  • Brother International PE-700II | Users Manual - English - Page 7
    -153 130013-154 No. Part Name 10 Spool net 11 Operation manual 12 Quick reference guide 13 Embroidery foot "Q" (on machine) Embroidery set (large) 14 H 18cm X W 13 cm (H 7 inches X W 5 inches) 15 Scissors 16 Dust cover 17 Accessory bag Part Code U.S.A. / Canada Others XA5523-050 XD1628
  • Brother International PE-700II | Users Manual - English - Page 8
    available as optional accessories. 1. 2. 3. 4. 5. 6. No. Part Name 1 Brother poly #90 bobbin thread Water solude stabilizer 2 Stabilizer material for embroidery 3 Embroidery card Part Code U.S.A. / Canada Other No. Part Name Part Code U.S.A. / Canada Other EBT-PE SA520 SA519 EBT
  • Brother International PE-700II | Users Manual - English - Page 9
    spool of thread on the spool pin. f Bobbin winder Use the bobbin winder when winding the bobbin. g Operation panel From the operation panel, patterns can be selected and edited, and operations for using the machine can be displayed (page 11). 8 h Embroidery unit connector slot Plug in the connector
  • Brother International PE-700II | Users Manual - English - Page 10
    guide. c Needle plate When the needle is lowered, it enters the hole in the needle plate. d Needle plate cover Remove the needle plate cover to clean the bobbin case and race. e Bobbin cover/bobbin case Remove the bobbin cover, and then insert the bobbin into the bobbin case. f Embroidery foot
  • Brother International PE-700II | Users Manual - English - Page 11
    embroidering. Red: The machine can not embroider. Orange: The machine is winding the bobbin thread, or the bobbin winder shaft is moved to the right side. b Needle position button Press the needle position button to raise or lower the needle. Pressing the button twice sews one stitch. c Thread
  • Brother International PE-700II | Users Manual - English - Page 12
    Crystal Display) Operation" (page 20). b Back key Press to return to the previous screen. c Previous page key Press to display the machine. Displays simple explanations of setting upper thread / bobbin winding / setting bobbin thread / embroidery unit attachment / embroidery frame attachment / needle
  • Brother International PE-700II | Users Manual - English - Page 13
    12
  • Brother International PE-700II | Users Manual - English - Page 14
    21 Checking machine operating procedures 23 Winding/Installing the Bobbin 24 Bobbin precautions 24 Winding the bobbin 24 Installing the bobbin 28 Upper Threading ...30 About the spool of thread 30 Threading the upper thread 30 Threading the needle 32 Threading the needle manually (without
  • Brother International PE-700II | Users Manual - English - Page 15
    is not attached, the machine does not operate.) For details, refer to "Attaching the embroidery unit" (page 15). ↓ 2 Checking the needle Use a needle matched to the fabric. For details on replacing the needle, refer to "Replacing the needle" (page 36). ↓ 3 Setting up the bobbin thread For the
  • Brother International PE-700II | Users Manual - English - Page 16
    . Get the included embroidery unit ready. Turn off the machine. a Slide the embroidery unit onto the machine b arm. Push it in until it clicks and stops. X The embroidery unit is attached. Turn on the machine. c • For details, refer to "Turning on the machine" (page 19). X The confirmation
  • Brother International PE-700II | Users Manual - English - Page 17
    moves to its initial position. Make sure that the machine is completely stopped and follow the instructions below. Remove the embroidery frame. a • For details on removing the embroidery frame, refer to "Removing the embroidery frame" (page 48). Press , and then press . b a a Carriage X The
  • Brother International PE-700II | Users Manual - English - Page 18
    Hold the release button on the bottom left of d the embroidery unit, and slowly pull the embroidery unit to the left. 1 a a Release button X The embroidery unit separates from the machine. CAUTION ● Do not carry the embroidery unit by holding the release button compartment. Attaching the
  • Brother International PE-700II | Users Manual - English - Page 19
    plugged in to them. Fire or electric shock may result. ● Do not touch the plug with wet hands. Electric shock may result. ● When unplugging the machine, always turn off the main power first. Always grasp the plug to remove it from the outlet. Pulling on the cord may damage the cord
  • Brother International PE-700II | Users Manual - English - Page 20
    to another location, be sure to turn it off. 1 refer to "Attaching the Embroidery Unit" (page 15).) Prepare the included power cord. Make sure that the machine is completely a stopped. Make sure that the machine is turned off (the a main power switch is set to " "), and then plug the power
  • Brother International PE-700II | Users Manual - English - Page 21
    screen is not displayed (page 21).) ■ Pattern type selection screen a b c d g e f a Embroidery patterns b Additional embroidery patterns c Alphabet patterns d Frame patterns e Embroidery card f Patterns stored in the machine's memory g Moves the embroidery unit carriage to its storage
  • Brother International PE-700II | Users Manual - English - Page 22
    the embroidery screen. (When "Thread No. #123" is selected) Thread color/Time to embroider/ Needle count/Thread number (#123) Embroidery/Country service count and the total Stitch counter number of embroidery stitches. The service count is a reminder to take your machine in for regular servicing.
  • Brother International PE-700II | Users Manual - English - Page 23
    GETTING READY Turn on the machine. a X The LCD comes on. Press b panel. (Settings key) on the operation X The settings screen appears. Press the item to be set. c Switch screens using (Previous page key) and (Next page key). † Example: Changing the maximum embroidering speed When
  • Brother International PE-700II | Users Manual - English - Page 24
    ) to return to the previous page. Displays simple explanations of setting upper thread / bobbin winding / setting bobbin thread / embroidery † Example: Upper threading 1 unit attachment / embroidery frame attachment / needle replacement on the LCD. Turn on the machine. a X The LCD comes on
  • Brother International PE-700II | Users Manual - English - Page 25
    place. CAUTION 1 ● Only use the Bobbin (part code: SA156, SFB: XA5539-151) designed specifically for this machine. Use of any other bobbin may result in injuries or damage to the machine. ● The included bobbin was designed specifically for this machine. If bobbins from other models are used, the
  • Brother International PE-700II | Users Manual - English - Page 26
    Place the spool of thread for the bobbin onto f the spool pin. Slide the spool onto the spool cap is too small for the spool being used, the thread may catch on the slit in the spool or the needle may break. ● a a Spool cap (small) b Spool (cross-wound thread) c Space z When using thread that
  • Brother International PE-700II | Users Manual - English - Page 27
    , i and then pull it to the right. 1 a Thread guide plate a Thread guide Note z Make sure that the thread passes under the pretension disk. While holding the thread with your left hand, k wind the thread that was pulled out clockwise around the bobbin five or six times with your right hand. Note
  • Brother International PE-700II | Users Manual - English - Page 28
    . 1 1 a Guide slit in bobbin winder seat (with built-in cutter) CAUTION ● Be sure to cut the thread as described. If the bobbin is wound without cutting the thread using the cutter built into the slit in the bobbin winder seat, the thread may become tangled in the bobbin or the needle may bend or
  • Brother International PE-700II | Users Manual - English - Page 29
    thread, otherwise the needle may break or the thread tension will be incorrect. ● The bobbin was designed specifically for this machine. If bobbins from other models are used, the machine will not operate correctly. Use only the included bobbin or bobbins of the same type (part code: SA156, SFB
  • Brother International PE-700II | Users Manual - English - Page 30
    is correctly inserted through the tension-adjusting spring of the bobbin case. If it is not inserted correctly, reinsert the thread. 1 a Tension-adjusting spring Reattach the bobbin cover. g Insert the tab in the lower-left corner of the bobbin cover, and then lightly press down on the right side
  • Brother International PE-700II | Users Manual - English - Page 31
    needle. CAUTION ● When threading the upper thread, carefully follow the instructions. If the upper threading is not correct, the thread may become tangled or the needle pin, and then thread the machine. Turn on the machine. a 1 a Needle position button X The needle is correctly raised when the
  • Brother International PE-700II | Users Manual - English - Page 32
    the thread with your left hand, and then pass the thread behind the thread guide cover and to the front. 1 CAUTION ● If the spool or the spool or the needle may break. a Thread guide cover Pass the thread under the thread guide plate, i and then pull it up. 1 a Thread guide plate Upper Threading
  • Brother International PE-700II | Users Manual - English - Page 33
    threader can be used with sewing machine needles 75/11 through 100/16. z Thread with a thickness of 130/20 or thicker cannot be used with the needle threader. z If the needle threader cannot be used, refer to "Threading the needle manually (without using the needle threader)" (page 34). Pull the end
  • Brother International PE-700II | Users Manual - English - Page 34
    the left side b of the machine. Lower the needle threader lever on the left d side of the machine until it clicks, and then slowly return the lever to its original position. 1 1 1 a Cutter Note z If the thread is pulled through and cannot be cut correctly, lower the embroidery foot so that the
  • Brother International PE-700II | Users Manual - English - Page 35
    the e thread through the embroidery foot hole. Threading the needle manually (without using the needle threader) X The upper needle threader, thread the needle as described below. Thread the machine to the needle bar thread a guide. • For details, refer to "Threading the upper thread" (page
  • Brother International PE-700II | Users Manual - English - Page 36
    are dispersed. Be sure to read and carefully follow the instructions below. CAUTION ● Only use home sewing machine needles. Use of any other needle may bend the needle or damage the machine. ● Never use bent needles. Bent needles can easily break, possibly resulting in injuries. Embroidering with
  • Brother International PE-700II | Users Manual - English - Page 37
    fabric or paper under the embroidery d foot to cover the hole in the needle plate. Replace the needle as described below. Use the screwdriver and a needle that has been determined to be straight according to the instructions in "Checking the needle" (page 35). Press (Needle position button) once or
  • Brother International PE-700II | Users Manual - English - Page 38
    the flat side of the needle toward the rear f of the machine, insert the needle until it touches the needle stopper. 1 1 a Needle stopper While holding the needle with your left hand, g use the screwdriver to tighten the needle clamp screw. CAUTION ● Be sure to insert the needle until it touches the
  • Brother International PE-700II | Users Manual - English - Page 39
    GETTING READY 38
  • Brother International PE-700II | Users Manual - English - Page 40
    embroidery frame 43 Attaching the Embroidery Frame.........47 Attaching the embroidery frame ....47 Removing the embroidery frame ....48 Selecting Embroidery Patterns 49 Copyright information 49 Embroidery 65 Thread runs out partway through a design 65 Stopping while embroidering .........66
  • Brother International PE-700II | Users Manual - English - Page 41
    the fabric, causing the needle to break. For the bobbin thread, use the embroidery bobbin thread. For details, refer to "Optional accessories" (page 7). Note z For good quality embroidery designs be sure to use embroidery thread designed for embroidery machines. z Before starting to embroider
  • Brother International PE-700II | Users Manual - English - Page 42
    thick fabrics such as denim, use a 90/14 home sewing machine needle. Memo z A 75/11 needle is already installed when the machine is purchased. z When replacing the needle, refer to "Replacing the needle" (page 36). 2 ■ Other Embroidery frames "small", "medium" and "extra large (multi-position
  • Brother International PE-700II | Users Manual - English - Page 43
    to the fabric to prevent poor quality embroidery designs. Memo z We recommend the stabilizer material for embroidery. Use a water soluble stabilizer on thin materials like organdy and fabrics with a nap like towels. For details, refer to "Optional accessories" (page 7). 1 3 2 a Fabric b Size of
  • Brother International PE-700II | Users Manual - English - Page 44
    frame that matches the size of the pattern being embroidered. Otherwise, the embroidery frame may be hit by the embroidery foot and cause injury or needle breakage. ■ Embroidery frame (medium)[option] Patterns with a height of up to 10 cm (4 inches) and a width of up to 10 cm (4 inches) can
  • Brother International PE-700II | Users Manual - English - Page 45
    EMBROIDERY Press the inner frame in from the top of the c fabric. Line up on the inner frame and on outer frame. Press the inner frame
  • Brother International PE-700II | Users Manual - English - Page 46
    the fabric on the d outer frame and stretch the fabric. • For details, refer to page 43. Remove the embroidery sheet. e 1 2 a Embroidery pattern b Mark Place the embroidery sheet on the inner frame. b 1 3 2 a Embroidery sheet b Inner frame c Embroidery sheet base lines Preparing the Fabric 45
  • Brother International PE-700II | Users Manual - English - Page 47
    pieces of fabric that cannot be stretched on an embroidery frame or thin pieces like ribbon are being embroidered, use stabilizer material as a base to stretch on the frame. We recommend stabilizer material for all embroidery. 1 2 3 1 3 2 1 3 a Stabilizer material b Tack or spray glue c Fabric After
  • Brother International PE-700II | Users Manual - English - Page 48
    embroidery frame. Attaching the embroidery frame Wind the embroidery bobbin thread onto the a bobbin and set it into the bobbin case. • For details, refer to "Winding/Installing the Bobbin" (page hit the needle with your finger or the embroidery frame. It may cause injury or needle breakage. While
  • Brother International PE-700II | Users Manual - English - Page 49
    foot lever even further. Make sure that the machine is completely stopped and follow the instructions below. Raise the presser foot lever. a a a Presser foot lever While pushing the lever of the embroidery b frame holder to the left, lift the embroidery frame up to remove it. Remove the back
  • Brother International PE-700II | Users Manual - English - Page 50
    types. The patterns stored in the machine and embroidery cards are intended for private use instructions displayed on the screen. • For details, refer to "Selecting an embroidery pattern" (page 53). ■ Alphabet patterns There are 6 types of characters (European characters); upper case/lower case
  • Brother International PE-700II | Users Manual - English - Page 51
    . [650SPM/350SPM] NAME OF COLOR: Typical color name TIME: Time required for embroidering NEEDLE COUNT: Needle progress number #123: Select from the following thread color number sets • EMBROIDERY (POLYESTER) THREAD# • COUNTRY (COTTON) THREAD# • MADEIRA POLY THREAD# • MADEIRA RAYON THREAD# • SULKY
  • Brother International PE-700II | Users Manual - English - Page 52
    to cancel multicolor. 2 The needle progresses one color or one stitch (if pressed continuously, 9 stitches to 20 stitches) at a time and changes the position for starting the embroidery. This is used when a specific color is not embroidered or when restarting the machine after power has been turned
  • Brother International PE-700II | Users Manual - English - Page 53
    . Memo z When "The pattern is too large for the embroidery frame." is displayed, no more characters can be entered. z Characters of different styles (sans serif, serif, and outline, etc.) cannot be combined. Select the alphabet
  • Brother International PE-700II | Users Manual - English - Page 54
    patterns" (page 63). Selecting an embroidery pattern There are total of 136 embroidery patterns, such as fruits and animals, stored in the machine's memory. 70 Embroidery patterns 66 Embroidery patterns Memo z Refer to "Embroidery Pattern Color Change Table" in the Quick reference guide for samples
  • Brother International PE-700II | Users Manual - English - Page 55
    EMBROIDERY Selecting a frame pattern 10 shapes, such as squares and circles, can be combined with 12 stitch types. Select the stitch. c Switch the screen using (Previous page key) (Next page key), and select from the 12 stitches. Memo z Refer to "Frame patterns" in the Quick reference guide
  • Brother International PE-700II | Users Manual - English - Page 56
    other than an embroidery card in the embroidery card slot. z When embroidery cards are not in use, keep them in their storage cases. z Use only embroidery cards manufactured for this machine. Using unauthorized cards may cause your machine to operate incorrectly. z Embroidery cards purchased in
  • Brother International PE-700II | Users Manual - English - Page 57
    Upper thread Bobbin thread Use embroidery thread, or country embroidery thread intended for use with this machine. Other embroidery threads may not yield optimum results. Use embroidery bobbin thread intended for use with this machine. For details, refer to "Optional accessories" (page 7). Memo
  • Brother International PE-700II | Users Manual - English - Page 58
    part e Next color part • The thread color number set displayed for the thread colors can be changed. Press (Settings key), and then change the setting in the settings screen. For details, refer to "LCD (liquid crystal display) operation" (page 50). Set the embroidery thread, thread the needle
  • Brother International PE-700II | Users Manual - English - Page 59
    already been cut, otherwise the needle may break, the threads may become tangled or damage to the machine may occur. ● Do not press (Thread cutter button) if there is no fabric under the embroidery foot or while the machine is embroidering, otherwise damage to the machine may occur. • If the thread
  • Brother International PE-700II | Users Manual - English - Page 60
    stitching, it will not be finished neatly. Stretch the base fabric on the embroidery e frame. When "APPLIQUE MATERIAL" is displayed on b the screen, apply stop button). X The cut-out for the appliqué piece is sewn, and the machine stops. 1 1 2 a Appliqué position b Base fabric X "APPLIQUE" will be
  • Brother International PE-700II | Users Manual - English - Page 61
    EMBROIDERY Lower the presser foot lever, and press i (Start/stop button). Note z When "APPLIQUE MATERIAL", "APPLIQUE POSITION" and "APPLIQUE" are displayed, a specific color thread does not appear. Use a proper color thread to match the appliqué piece. Follow the instructions on the screen, and j
  • Brother International PE-700II | Users Manual - English - Page 62
    layout Check and adjust the layout. c a bc d e f The pattern is normally positioned in the center of the embroidery frame. You can check the layout before starting embroidery and change the position and the size. k g 2 h j i Memo z Keys that appear surrounded with a dotted line cannot
  • Brother International PE-700II | Users Manual - English - Page 63
    EMBROIDERY Memo z If you make a note of the values in the lower part of screen when you change the size and position, you can embroider with the same size and layout even if you have to turn the power back on in the middle of your work. Starting point key Moves the needle start
  • Brother International PE-700II | Users Manual - English - Page 64
    patterns and the alphabet patterns you have customized can be stored in the machine's memory. Since the stored patterns will not be erased when the machine is turned off, you can always recall them for embroidery. This is convenient for storing names and the like. You can store up to
  • Brother International PE-700II | Users Manual - English - Page 65
    of memory space c Number of the currently displayed page from the total number of pages X The selected pattern is shown in reverse highlighting. saved from an embroidery card must have the embroidery card inserted in the machine in order to retrieve the memory saved from the embroidery card. 1
  • Brother International PE-700II | Users Manual - English - Page 66
    resewn with the correct color. Press (Start/stop button) to stop the a machine. Thread runs out partway through a design When the upper thread or the bobbin thread runs out while embroidering, the machine stops. Move the needle back about 10 stitches and resume embroidering. Press . b Set up the
  • Brother International PE-700II | Users Manual - English - Page 67
    before it is complete, check the current needle count before turning off the machine. Memo z When the machine is turned off, the embroidery size and layout return to the original setting. Press (Start/stop button) to stop the a machine. Check the current needle count on the screen b and make a note
  • Brother International PE-700II | Users Manual - English - Page 68
    Press (Forward one color) to move to 2 i the beginning of the color you want to embroider. Press (Forward one stitch) to increase j the needle count. If is pressed continuously, it moves forward 1 -> 9 -> 30 stitches. Move forward to about 10 stitches before the total number of stitches
  • Brother International PE-700II | Users Manual - English - Page 69
    EMBROIDERY 68
  • Brother International PE-700II | Users Manual - English - Page 70
    procedures are described in this chapter. Care and Maintenance 70 Cleaning the machine surface 70 Cleaning the race 70 Attaching the Embroidery Foot 72 Attaching the embroidery Foot "Q 72 Troubleshooting ...74 Error messages 78 Adjusting the LCD 81 Operation beep 81 Canceling the
  • Brother International PE-700II | Users Manual - English - Page 71
    cleaning the machine, otherwise injuries or an electric shock may occur. Remove the embroidery unit. c Grasp both sides of the needle plate cover, and d then slide it toward you. a a Needle plate cover X The needle plate cover is removed. Remove the bobbin case. e Grasp the bobbin case, and then
  • Brother International PE-700II | Users Manual - English - Page 72
    bobbin case (part code: XC8167- Note z If lint or dust collects on the bobbin thread sensor, the sensor may not operate correctly. 251), contact your nearest authorized service center. ● Be sure that the bobbin case is correctly installed, otherwise the needle may break. Insert the bobbin case
  • Brother International PE-700II | Users Manual - English - Page 73
    foot with your index finger wrapped around the lever at the back of the foot. a 1 a Needle position button Turn off the machine. b CAUTION ● Before attaching the embroidery foot, be sure to turn off the machine, otherwise injuries may occur if (Start/stop button) is accidentally pressed and the
  • Brother International PE-700II | Users Manual - English - Page 74
    . Firmly tighten the presser foot holder screw. g Turn the screwdriver toward the front. 3 CAUTION ● Do not hit the needle with your finger or the embroidery foot when attaching it. The needle may break or cause injury. ● Be sure to tighten the screw with the included screwdriver. If the screw is
  • Brother International PE-700II | Users Manual - English - Page 75
    it. Replace the embroidery foot. Contact your retailer or the nearest authorized service center. The bobbin case is scratched, or has a burr on it. Replace the bobbin case. Contact your retailer or the nearest authorized service center. A bobbin designed specifically for this machine is not used
  • Brother International PE-700II | Users Manual - English - Page 76
    it. Replace the bobbin case. Contact your retailer or the nearest authorized service center. - 3 A bobbin designed specifically for this machine is not used. Incorrect bobbins will not work properly. Only use a bobbin designed specifically for this machine. page 24 Bobbin thread does not wind
  • Brother International PE-700II | Users Manual - English - Page 77
    the bobbin case. Contact your retailer or the nearest authorized service center. A bobbin designed specifically for this machine is not used. Incorrect bobbins will not work properly. Only use a bobbin designed specifically for this machine. The thread does not pass through the eye of the needle
  • Brother International PE-700II | Users Manual - English - Page 78
    ., is plugged up. Remove the tangled thread. When the bobbin case is plugged up, clean the race. page 70 The thread tension is incorrect. Adjust the tension of the upper thread. page 64 If the embroidery unit carriage or 3 Embroidery not neatly done. Objects are placed near the carriage or
  • Brother International PE-700II | Users Manual - English - Page 79
    was pressed while the embroidery foot was raised. The memory is full and the pattern cannot be saved. You pressed the back key or the embroidery key while a pattern was selected. You tried to select an embroidery pattern or change the layout when the needle was down. The machine is turned on while
  • Brother International PE-700II | Users Manual - English - Page 80
    around the bobbin case, and the needle is bent and hitting the needle plate, etc., so the machine stops (refer to page 74). A card that cannot be used with this machine has been inserted, and you tried to select a pattern from the card. An embroidery card incompatible with this machine was inserted
  • Brother International PE-700II | Users Manual - English - Page 81
    APPENDIX Error Message Probable Cause The machine was turned on before the embroidery unit was attached. The bobbin winder is winding the bobbin. 80
  • Brother International PE-700II | Users Manual - English - Page 82
    turned on, the brightness of the LCD is either too light or too dark. In such a case, perform the following operation. Turn off the machine. a Each time a key is pressed you will hear one beep. If an incorrect operation is performed you will hear two or four beeps. ■ If a key
  • Brother International PE-700II | Users Manual - English - Page 83
    does not beep. Turn on the machine. a Press e (Back key). X The LCD comes on. Press b panel. (Settings key) on the operation X The initial screen appears again. X The settings screen appears. Press c (Next page key) three times. Press OFF for the buzzer. d X The screen for changing
  • Brother International PE-700II | Users Manual - English - Page 84
    bobbin winding 24 bobbin winding thread guide 8 M Brother poly #90 bobbin thread 7 buzzer 82 machine settings 21 , main power switch 9 19 C characters 52 maintenance 70 manual needle threading 34 , memory key 11 63 cleaning 70 cleaning brush 6 N D dust cover 6 E , embroidery
  • Brother International PE-700II | Users Manual - English - Page 85
    pattern 63 release button 17 resewing 65 S safety instructions 1 scissors 6 screwdriver 6 seam ripper 6 guide cover 8 thread guide disk 9 thread guide plate 8 thread take-up lever check window 8 thread tension adjustment 64 top cover 8 touch panel 11 troubleshooting 74 turning machine
  • Brother International PE-700II | Users Manual - English - Page 86
    English 882-U30 XD1628-051 Printed in Taiwan
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Computerized Embroidery Machine
Operation Manual
GETTING READY
EMBROIDERY
APPENDIX