Brother International S-7200B Service Manual - Page 18

FUNCTION SETTINGS OPERATION PANEL, Function No. 61, Used Time is set using Function No. 73

Get Brother International S-7200B PDF manuals and user guides View all Brother International S-7200B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

3. FUNCTION SETTINGS (OPERATION PANEL) Function No. 61 − 68 No. Initial value 61 0 62 (NOTE 18) 0 63 0 64 0 65 (NOTE 18) 66 (NOTE 18) 150 (ms) 0 67 (NOTE 18) 0 (degrees) 68 (NOTE 20) 0 Setting range 0 - 1 0 - 1 0 - 1 0 - 2 10 - 500 (ms) 0 - 1 -20 - 20 (degrees) 0 - 1 Setting details Highest needle position stop operation 0: Not used 1: Used Thread wiping operation during highest needle position stop operation 0: Thread wiping occurs after needle stops in highest position 1: Thread wiping occurs after thread trimming, and then needle bar is raised Thread trimming timer operation 0: Not used (Thread trimming is off when needle bar is stopped at the up position) 1: Used (Time is set using Function No. 73) 0: Standard 1: Not used 2: Twin needle lock stitcher (T-8422A-[][]3) [Do not change this setting] Delay time until reverse operation starts during highest needle position stop operation Presser foot lift timing during highest needle position stop operation 0: Presser foot is raised after needle bar is raised 1: Presser foot is raised before needle bar lift operation starts (See NOTE 19) Highest needle position stop position setting Becomes lower Becomes higher Seam matching function during automatic backtacking 0: Operation does not stop when switching cloth feed direction 1: Operation momentarily stops when switching cloth feed direction 2248M (NOTE 18) Setting is enabled when Function No. 61 is set to "1". (NOTE 19) Operation is disabled when Function No. 62 is set to "1". Presser foot is raised after needle bar is raised. (NOTE 20) Used when you would like to match the seam accurately during automatic backtacking. Use Function No. 78 to set the stop position and Function No. 79 to change the time before restarting. 11 S-7200B

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
S-7200B
3. FUNCTION SETTINGS (OPERATION PANEL)
11
Becomes lower
Becomes higher
Function No. 61
−
68
No.
Initial value
Setting range
Setting details
61
0
0
–
1
Highest needle position stop operation
0: Not used
1: Used
62
(NOTE 18)
0
0
–
1
Thread wiping operation during highest needle position stop operation
0: Thread wiping occurs after needle stops in highest position
1: Thread wiping occurs after thread trimming, and then needle bar is raised
63
0
0
–
1
Thread trimming timer operation
0: Not used (Thread trimming is off when needle bar is stopped at the up
position)
1: Used (Time is set using Function No. 73)
64
0
0
–
2
0: Standard
1: Not used
2: Twin needle lock stitcher (T-8422A-[][]3)
[Do not change this setting]
65
(NOTE 18)
150 (ms)
10
–
500 (ms)
Delay time until reverse operation starts during highest needle position stop
operation
66
(NOTE 18)
0
0
–
1
Presser foot lift timing during highest needle position stop operation
0: Presser foot is raised after needle bar is raised
1: Presser foot is raised before needle bar lift operation starts (See NOTE
19)
67
(NOTE 18)
0 (degrees)
-20
–
20
(degrees)
Highest needle position stop position setting
68
(NOTE 20)
0
0
–
1
Seam matching function during automatic backtacking
0: Operation does not stop when switching cloth feed direction
1: Operation momentarily stops when switching cloth feed direction
(NOTE 18) Setting is enabled when Function No. 61 is set to “1”.
(NOTE 19) Operation is disabled when Function No. 62 is set to “1”. Presser foot is raised after needle bar is raised.
(NOTE 20) Used when you would like to match the seam accurately during automatic backtacking. Use Function No. 78 to
set the stop position and Function No. 79 to change the time before restarting.
2248M