Brother International S-7200B Service Manual - Page 27

FUNCTION SETTINGS OPERATION PANEL, Function No. 119, High flicker reduction

Get Brother International S-7200B PDF manuals and user guides View all Brother International S-7200B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

3. FUNCTION SETTINGS (OPERATION PANEL) Function No. 119 − 131 No. Initial value 119 3 120 5 121 (NOTE 38) 3000 (rpm) 122 (NOTE 38) 1000 (rpm) 123 45 (degrees) 124* 0 125 0 126 1 (seconds) 127 100 128 0 129 0 130 0 131 - Setting range - - 200 - 5000 (rpm) 200 - 5000 (rpm) 30 - 90 (degrees) 0 - 1 0 - 1 0 - 120 (seconds) - 0 - 3 -2 - 2 -2 - 2 - [Do not change this setting.] [Do not change this setting.] Setting details Speed when medium speed switch is on Speed when low speed switch is on Servo lock release angle (Do not change this setting.) Material edge sensor logic selection 0: Detects material absent 1: Detects material present Servo lock operation 0: None 1: When stopped 2: When presser foot lifting signal is on Servo lock timer setting 0: No timer operation 1-120: Timer operates (1-120 seconds) [Do not change this setting.] Flicker reduction function (when flickering occurs from fluorescent light) 0: None 1: Medium flicker reduction 2: Low flicker reduction 3: High flicker reduction 4: [Do not use this setting, otherwise the motor will overheat.] Motor acceleration gain [Do not change this setting.] Motor deceleration gain [Do not change this setting.] [Do not change this setting.] (NOTE 38) Setting is enabled when Function No. 69 is set to "2". *... Settings indicated with " * " are enabled when the power is turned off and then back on. Function No.132 − 136 The following function numbers show maintenance information. No. Description of displays 132 Cumulative power on time (Actual time = Displayed time x 10) 133 Cumulative operating time (Actual time = Displayed time xxxx x 10) 134 Cumulative grease-up running time (Time = Display xxxx x 1 hour) / Grease life estimate (%) 135 ROM version (x.xxx) 136 Set maximum speed history (rpm) S-7200B 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
S-7200B
3. FUNCTION SETTINGS (OPERATION PANEL)
20
Function No. 119
−
131
No.
Initial value
Setting range
Setting details
119
3
–
[Do not change this setting.]
120
5
–
[Do not change this setting.]
121
(NOTE 38)
3000 (rpm)
200
–
5000
(rpm)
Speed when medium speed switch is on
122
(NOTE 38)
1000 (rpm)
200
–
5000
(rpm)
Speed when low speed switch is on
123
45
(degrees)
30
–
90
(degrees)
Servo lock release angle (Do not change this setting.)
124*
0
0
–
1
Material edge sensor logic selection
0: Detects material absent
1: Detects material present
125
0
0
–
1
Servo lock operation
0: None
1: When stopped
2: When presser foot lifting signal is on
126
1 (seconds)
0
–
120
(seconds)
Servo lock timer setting
0: No timer operation
1
–
120: Timer operates (1
–
120 seconds)
127
100
–
[Do not change this setting.]
128
0
0
–
3
Flicker reduction function (when flickering occurs from fluorescent light)
0: None
1: Medium flicker reduction
2: Low flicker reduction
3: High flicker reduction
4: [Do not use this setting, otherwise the motor will overheat.]
129
0
-2
–
2
Motor acceleration gain [Do not change this setting.]
130
0
-2
–
2
Motor deceleration gain [Do not change this setting.]
131
–
–
[Do not change this setting.]
(NOTE 38) Setting is enabled when Function No. 69 is set to “2”.
*…
Settings indicated with “ * “ are enabled when the power is turned off and then back on.
Function No.132
−
136
The following function numbers show maintenance information.
No.
Description of displays
132
Cumulative power on time (Actual time = Displayed time x 10)
133
Cumulative operating time (Actual time = Displayed time xxxx x 10)
134
Cumulative grease-up running time (Time = Display xxxx x 1 hour) / Grease life estimate (%)
135
ROM version (x.xxx)
136
Set maximum speed history (rpm)