Brother International SM-6500PRW Users Manual - English - Page 15

For models equipped with the fast bobbin, winding system

Get Brother International SM-6500PRW PDF manuals and user guides View all Brother International SM-6500PRW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

■ For models equipped with the fast bobbin winding system Slide the sewing speed controller to the right f (to set the speed to fast) (for models equipped with the sewing speed controller). Follow steps 1 through 2 of the procedure in a "Winding the bobbin" to pass the thread around the pre-tension disk (page 11). 1 Place the bobbin on the bobbin winder shaft b so that the spring on the shaft fits into the notch in the bobbin. a Sewing speed controller a Notch b Bobbin winder shaft spring Slide the bobbin winder shaft to the right. c While holding the thread that wraps around the d pre-tension disk with your left hand, use your right hand to wind the free end of the thread clockwise around the bobbin five or six times. Turn on the sewing machine. g Press the foot controller or press (start/ h stop button) (for models equipped with the start/stop button) to start. Note ● If the sewing machine is to be operated using the foot controller, connect the foot controller before turning on the machine. ● When the foot controller is plugged in, the start/stop button cannot be used to start or stop sewing (only for models equipped with the start/stop button). When the bobbin begins spinning slowly, take i your foot off the foot controller or press (start/stop button) (for models equipped with the start/stop button). Cut the thread, slide the bobbin winder shaft j to the left and remove the bobbin. Pull the thread to the right and pass it through e the slit in the bobbin winder seat. Slide the sewing speed controller back to its k original position (for models equipped with the sewing speed controller). CAUTION ● Not winding the bobbin properly may cause the thread tension to loosen, and may break the needle. a Slit in bobbin winder seat (with built-in cutter) X The thread is cut to a suitable length. CAUTION ● Be sure to cut the thread as described. If the bobbin is wound without cutting the thread using the cutter built into the slit in the bobbin winder seat, the thread may become tangled in the bobbin or the needle may bend or break when the bobbin thread starts to run out. 1 2 a Wound evenly b Wound poorly 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
13
1
■
For models equipped with the fast bobbin
winding system
a
Follow steps
1
through
2
of the procedure in
“Winding the bobbin” to pass the thread
around the pre-tension disk (page 11).
b
Place the bobbin on the bobbin winder shaft
so that the spring on the shaft fits into the
notch in the bobbin.
a
Notch
b
Bobbin winder shaft spring
c
Slide the bobbin winder shaft to the right.
d
While holding the thread that wraps around the
pre-tension disk with your left hand, use your
right hand to wind the free end of the thread
clockwise around the bobbin five or six times.
e
Pull the thread to the right and pass it through
the slit in the bobbin winder seat.
a
Slit in bobbin winder seat (with built-in cutter)
The thread is cut to a suitable length.
f
Slide the sewing speed controller to the right
(to set the speed to fast) (for models equipped
with the sewing speed controller).
a
Sewing speed controller
g
Turn on the sewing machine.
h
Press the foot controller or press
(start/
stop button) (for models equipped with the
start/stop button) to start.
Note
●
If the sewing machine is to be operated
using the foot controller, connect the foot
controller before turning on the machine.
●
When the foot controller is plugged in, the
start/stop button cannot be used to start or
stop sewing (only for models equipped with
the start/stop button).
i
When the bobbin begins spinning slowly, take
your foot off the foot controller or press
(start/stop button) (for models equipped with
the start/stop button).
j
Cut the thread, slide the bobbin winder shaft
to the left and remove the bobbin.
k
Slide the sewing speed controller back to its
original position (for models equipped with
the sewing speed controller).
●
Be sure to cut the thread as described. If the bobbin is
wound without cutting the thread using the cutter built
into the slit in the bobbin winder seat, the thread may
become tangled in the bobbin or the needle may bend
or break when the bobbin thread starts to run out.
CAUTION
●
Not winding the bobbin properly may cause the
thread tension to loosen, and may break the needle.
a
Wound evenly
b
Wound poorly
CAUTION
1
2