Canon CR-N300 Remote Camera Settings Guide

Canon CR-N300 Manual

Get Canon CR-N300 PDF manuals and user guides View all Canon CR-N300 manuals
Add to My Manuals
Save this manual to your list of manuals

Canon CR-N300 manual content summary:

  • Canon CR-N300 | Remote Camera Settings Guide - Page 1
    Remote Camera Settings Guide This document should be read before using the product. ENGLISH
  • Canon CR-N300 | Remote Camera Settings Guide - Page 2
    Guide/Important Information" included with the camera. * The cameras described in this document may include models not available in your country and/or region. For the latest information on this product (firmware and software, user manuals, operating environment, etc.), please refer to the Canon
  • Canon CR-N300 | Remote Camera Settings Guide - Page 3
    code corresponding to the latest version. - Address: Open Source Promotion Division, Canon Inc. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan - For Canon's privacy policy, refer to Canon Global Website . This product is licensed under AT&T patents for the MPEG
  • Canon CR-N300 | Remote Camera Settings Guide - Page 4
    resulting recordings or footage complies with applicable laws, rules and regulations. Canon Inc. and its affiliates shall have absolutely no liability with respect . • Some jurisdictions require signage disclosing the existence of camera equipment. Please check your own area's laws for requirements
  • Canon CR-N300 | Remote Camera Settings Guide - Page 5
    , and downloading information from the Canon website. "Settings Guide" (This Guide) This explains the camera initial settings, other settings on the Settings Page, troubleshooting, and major specifications, etc. "Remote Camera Control Application User Manual" This explains details on how to use
  • Canon CR-N300 | Remote Camera Settings Guide - Page 6
     Symbols Used in This Document Symbol Caution Important Note Meaning Failure to follow the instructions indicated by this symbol may result in property damage other than this product. Be sure to follow these precautions. Cautions and restrictions during operation. Make
  • Canon CR-N300 | Remote Camera Settings Guide - Page 7
    Initial Camera Settings 17 Settings using the Camera Search Tool 17 Camera's Settings Page from the Web Browser 19 Chapter 2 Camera Setup Overview 35 Focus Settings (CR-N500 37 Autofocus ...37 Manual Focus...40 Focus Settings (CR-N300 42 Autofocus ...42 Manual Focus...44 PTZ/IS Settings ...45
  • Canon CR-N300 | Remote Camera Settings Guide - Page 8
    Setting Items ...49 Common Operations...49 [System] > [Video and Audio] > [HDMI/SDI 51 HDMI/SDI ...51 SDI ...51 [System] > [Video and Audio] > [IP Streaming Video 52 Mainstream ...52 Substream 1...53 Substream 2...53 [System] > [Video and Audio] > [Audio 54 General Audio ...54 IP Audio Streaming
  • Canon CR-N300 | Remote Camera Settings Guide - Page 9
    of Parts 86 Handling the Remote Controller 88 Chapter 4 Appendix USB Camera Functions (CR-N300 90 Image Adjustment/Camera Control Functions 90 Troubleshooting...91 List of Log Messages ...93 Log Messages on the Camera 93 Error Log ...93 Warning log...95 Notification log ...96 Restoring
  • Canon CR-N300 | Remote Camera Settings Guide - Page 10
    External Surface 105 Cleaning the Lens ...105 Specifications ...106 CR-N500 Main Unit ...106 CR-N300 Main Unit ...108 Accessories ...110 Operating Environment ...110 6: Disabling Unused Functions 115 Precautions When Disposing the Camera 116 Encrypting Backup Information 116 Index...117 10
  • Canon CR-N300 | Remote Camera Settings Guide - Page 11
    Chapter Before Use This chapter explains the software related to the camera and examples of system configuration. It also describes the preparation and settings after installing the camera.
  • Canon CR-N300 | Remote Camera Settings Guide - Page 12
    Controller Web Conference Tools, etc. Computer PoE+ Hub LAN RTMP Server NDI-Supported Switcher USB N300 SDI OUT HDMI OUT RS-422 Standard Communication (Serial) Supported Controller • Settings Page • Remote Camera Control Application N500 GEN LOCK Wi-Fi (Wireless LAN) INPUT1 N500 INPUT2 N500
  • Canon CR-N300 | Remote Camera Settings Guide - Page 13
    + Hub LAN SDI OUT Switcher LAN SDI OUT  System Layout Example 2 The following is an example of network connected camera control using application. Remote Camera Control Application RTMP Server LAN Computer PoE+ Hub RTP Client  System Layout Example 3 The following is an example with
  • Canon CR-N300 | Remote Camera Settings Guide - Page 14
     System Layout Example 4 The following is an example of connecting the camera as a USB camera. It is necessary to connect a headset, microphone, speakers, etc. to the computer separately, to hold web conferences. IR Remote Controller USB Power supplied by the Compact Power Adapter 14
  • Canon CR-N300 | Remote Camera Settings Guide - Page 15
    software can be used to set up and operate the camera efficiently. Download the software to use from the website written in the "Installation Guide/Important Information". Camera Search Tool This tool is used for connecting the camera to the computer over a network first. For details, refer to
  • Canon CR-N300 | Remote Camera Settings Guide - Page 16
    Security Checking/Settings The security function of the OS or web browser may block the setting and operation of the camera. Check the security settings beforehand, and change the settings if required. Checking the Firewall Settings To use the software on a computer with Windows Defender Firewall
  • Canon CR-N300 | Remote Camera Settings Guide - Page 17
    link-local address. • If IPv6 is not available, either assign an IPv4 address on the DHCP server or use the AutoIP feature to detect the camera. To use the AutoIP function, set the computer to [Automatically obtain IP address] in the Windows network settings, and connect the computer and
  • Canon CR-N300 | Remote Camera Settings Guide - Page 18
    output video are determined according to the set frame frequency. • When using the camera as a USB camera, set the frame frequency to 59.94 Hz or 50.00 Hz. N300 6 Repeat steps 3 to 5 to initialize multiple cameras. To exit the camera search tool, click [Exit] in the [File] menu or click the button
  • Canon CR-N300 | Remote Camera Settings Guide - Page 19
    the IP address of 192.168.100.1 approximately 2 minutes after connecting the camera to the network environment. • If an IPv4 address is assigned by the same network, the same IP address will be assigned, and access to the camera with 192.168.100.1 will not be possible. 1 When accessing with 192.
  • Canon CR-N300 | Remote Camera Settings Guide - Page 20
    Chapter Camera Setup The settings required to use the camera are made on the Settings Page. Before starting operation, make various settings on the Settings Page according to the shooting conditions and purpose. There are also menus that can be performed during operation, such as camera maintenance.
  • Canon CR-N300 | Remote Camera Settings Guide - Page 21
    (P. 100). However, because the Administrator Account and other settings will be initialized, it will no longer be able to connect to the camera as it is. Use the Camera Search tool to perform initialization setting. • Do not open multiple Setting Pages at one time and try to change the settings of
  • Canon CR-N300 | Remote Camera Settings Guide - Page 22
    configured in step 2.  Cautions and Troubleshooting for Wireless LAN Connection If experiencing "Slow support) • When using a wireless LAN indoors, install the camera and network device in the same room. • Install the camera changing the channel may solve the problem. • IEEE 802.11 b/g/n wireless
  • Canon CR-N300 | Remote Camera Settings Guide - Page 23
    stop HDMI/SD output or IP distribution of videos. If is clicked while the camera is on, "This will switch to standby. Do you want to continue?" to return to the power on state. The power lamp on the front of the camera is as follows: On (green): Power on ON (orange): Standby Blinking (green):
  • Canon CR-N300 | Remote Camera Settings Guide - Page 24
    Use the T or W button to fine-tune the position.  Settings Area Change camera settings. Click each tab to switch the settings area. (9) [Exposure] tab (P. (13) [Focus] tab (P. 37, 42) Sets focus settings. (14) [PTZ/IS] tab (P. 45) Sets pan, tilt, and zoom operations and image stabilizer
  • Canon CR-N300 | Remote Camera Settings Guide - Page 25
    not guarantee exact precision. Operation by Clicking on the Video Display Area or by Slider  Click Operation When clicking on the video display area, the camera angle moves so that the position of the mouse pointer is at the center. If a single click does not center to the desired location, repeat
  • Canon CR-N300 | Remote Camera Settings Guide - Page 26
    the Digital Zoom and Digital Tele-Converter When [PTZ/IS] > [Digital Zoom] is set to [300x] N500 , [400x] N300 , the digital zoom area is displayed on the zoom slider and digital zoom operation is enabled. Digital zoom area Optical zoom area When [PTZ/IS] > [Digital Zoom] is set to [Digital Tele
  • Canon CR-N300 | Remote Camera Settings Guide - Page 27
    and iris are adjusted automatically. (Iris Priority AE) N300 The iris is adjusted manually. The shutter speed and gain are adjusted automatically. (Manual Exposure) The exposure (iris, shutter speed, gain, etc.) is adjusted manually. (Portrait) N300 Blurs the background to make the subject stand out
  • Canon CR-N300 | Remote Camera Settings Guide - Page 28
    is automatically adjusted. When [Auto] is off, the iris can be manually adjusted. Moving the slider to the left opens the aperture and brightens F4.4, F4.5, F4.8, F5.2, F5.6, F6.2, F6.7, F7.3, F8.0, F8.7, F9.5, F10, F11 N300 F1.8, F2.0, F2.2, F2.4, F2.6, F2.8, F3.1, F3.4, F3.7, F4.0, F4.4, F4.8, F5
  • Canon CR-N300 | Remote Camera Settings Guide - Page 29
    the shutter speed by frequency. This is used to reduce black bands on the screen, flickering from fluorescent lighting, and manually adjusted. Adjustment can be made in the ranges below. N500 -6.0 to 33.0 dB (by 0.5) N300 0.0 to 36.0 dB (by 0.5) When [Image Quality] > [Gamma] is [Wide DR] or [Canon
  • Canon CR-N300 | Remote Camera Settings Guide - Page 30
    Shutter".  About Shooting with Slow Shutter By setting the [Shooting Mode] to (Manual Exposure) or (Shutter Priority AE) N300 to set a slow shutter speed, setting it to (Low Light) N300 , or setting the [Auto Slow Shutter] N300 to [ON], it is possible to shoot the subject brightly even where
  • Canon CR-N300 | Remote Camera Settings Guide - Page 31
    AWB fixed) and [Color Temperature (K)] are displayed. N300 (Low Light), or (Spotlight), only [White Balance to 15000 K to adjust the white balance. [Manual] Set [R Gain] and [B Gain] as desired and [Set B]. The settings are erased after the camera is restarted or turned off/on, so register them
  • Canon CR-N300 | Remote Camera Settings Guide - Page 32
    [Color Matrix: Gain], [Color Matrix: Phase], [Color Matrix: R-G], [Color Matrix: R-B], [Color Matrix: G-R], [Color Matrix: G-B], [Color Matrix: B-R], [Color Matrix: B-G] The color matrix allows to fine-tune the tone of the video. Settings Gain Phase R-G R-B G-R G-B B-R B-G Adjustment Items Color
  • Canon CR-N300 | Remote Camera Settings Guide - Page 33
    gradation in the shadow areas more compared to Normal 1. N300 [Normal 4 (x5.0)] N500 Able to express black gradation in the shadow areas more compared to Normal 3. [Wide DR] N500 Ensures a wide dynamic range. Used to output to a TV monitor. [Canon Log3] N500 Gamma for postproduction processing. 33
  • Canon CR-N300 | Remote Camera Settings Guide - Page 34
    Normal 2/3/4 Normal 1 Output Output Output Normal 4 Normal 3 Normal 1/2 Input Canon Log 3 Wide DR Normal1 Input Input Wide DR Normal1 Note Canon Log3 provides a wide dynamic range that maximizes the characteristics of the image sensor. N500 [Color Space] Select a color space. [BT.2020 Gamut]
  • Canon CR-N300 | Remote Camera Settings Guide - Page 35
    will not be displayed. N500 [Black:Master Black Red], [Black:Master Black Blue] Corrects R and B individually for black color casts. When [Image Quality] > [Gamma] is set to [Canon Log3], it will not be displayed. N500 [Black Gamma:Level], [Black Gamma:Range], [Black Gamma:Point] Corrects gamma in
  • Canon CR-N300 | Remote Camera Settings Guide - Page 36
    - Saturation: Adjusts the color intensity in the highlighted areas. Slope Point Output Output Input Input This function will not be displayed when [Image Quality] > [Gamma] is set to [Wide DR] or [Canon Log3]. N500 36
  • Canon CR-N300 | Remote Camera Settings Guide - Page 37
    Focus Settings (CR-N500) There are two focus adjustment modes: "Autofocus" and "Manual focus". Switch the [AF] on in the focus mode to select the autofocus or switch it to off to select the manual focus. The items that can be set differ depending on the focus mode. Autofocus Autofocus adjusts the
  • Canon CR-N300 | Remote Camera Settings Guide - Page 38
    Frame representing the main face (if even one face) Frame representing a non-main face Click on a face frame to track that face (P. 38). • When there is no face in the screen The [AF Frame Size] setting determines the focus position (P. 38). [Face Only] Focuses only on the person's face. If there is
  • Canon CR-N300 | Remote Camera Settings Guide - Page 39
    view Repeated pattern - When [Image Quality] > [Gamma] is set to [Canon Log3] or [Wide DR] - When the iris is narrowed down - When second (at 23.98 Hz). - When [PTZ/IS] > [Digital Zoom] is set to [300x] and the image size is magnified by more than 60 times - [PTZ/IS] > [Digital Zoom] > [Digital
  • Canon CR-N300 | Remote Camera Settings Guide - Page 40
    the lens and inside the camera body. Check the focus again before shooting. [Focus Mode] Turning [AF] off switches to manual focus mode. [Adjust Focus] with autofocus" (P. 39), the focus guide frame may not be displayed correctly. • The focus guide is not available if: - [PTZ/IS] > [Digital Zoom] is
  • Canon CR-N300 | Remote Camera Settings Guide - Page 41
    - [PTZ/IS] > [Digital Zoom] > [Digital Tele-Converter] is set to [3.0x] or [6.0x] • The face detection is not available if: - Shutter speed slower than 1/30 of a
  • Canon CR-N300 | Remote Camera Settings Guide - Page 42
    Focus Settings (CR-N300) There are two focus adjustment modes: "Autofocus" and "Manual focus". Switch the [AF] on in the focus mode to select the autofocus or switch it to off to select the manual focus. The items that can be set differ depending on the focus mode. Autofocus Autofocus adjusts the
  • Canon CR-N300 | Remote Camera Settings Guide - Page 43
    [AF Speed] Selects the autofocus adjustment speed. [High] Operates AF at the fastest speed. Effective for high brightness or night view. Uses the external sensor at the same time. [Normal] Operates more smoothly compared to [High]. Uses the external sensor at the same time. [Low] Stable AF operation
  • Canon CR-N300 | Remote Camera Settings Guide - Page 44
    is magnified by more than 80 times - [PTZ/IS] > [Digital Zoom] > [Digital Tele-Converter] to [6.0x] Manual Focus Manual Focus makes the focus position move manually. Note • If a zoom operation is performed after focusing, the focus may shift. • If the camera is left turned on, the focus may shift
  • Canon CR-N300 | Remote Camera Settings Guide - Page 45
    PTZ/IS Settings Settings for the camera's pan, tilt, and zoom operations and image stabilizer. [Digital Zoom] Select whether to use a digital zoom (300x N500 , 400x N300 a function that reduces the blurring of videos caused by camera vibration. [Standard] corrects relatively small blurs. [Powered IS
  • Canon CR-N300 | Remote Camera Settings Guide - Page 46
    the preset items and click [Add] (1) (2) (1) [Preset Name] Enter a preset name. (2) [PTZF], [Camera Settings] Check the items to preset. Item PTZF Camera Settings Preset target Pan/Tilt/Zoom position [Focus] [PTZ/IS] > [Digital Zoom], [Pan/Tilt Acceleration] [Exposure] [WB/Color] [Image Quality
  • Canon CR-N300 | Remote Camera Settings Guide - Page 47
    [Time] or [Speed Level] and adjust the value with the slider, and then click [View]. Note • If the pan/tilt/zoom or focus of the camera is operated while a preset is running, the preset stops. However, another preset can be called while a preset is running. • If [Stop] is clicked while a preset
  • Canon CR-N300 | Remote Camera Settings Guide - Page 48
    System Settings Configure advanced camera system settings such as video and audio, server, communications, and security. If selecting the [System] tab in settings, the video display/operation area disappears and
  • Canon CR-N300 | Remote Camera Settings Guide - Page 49
    SDI mapping (P. 51) General settings of the video, such as video size and quality sent from the camera (P. 52) Setting the bit rate for audio input from a microphone connected to the camera or IP audio streaming (P. 54) Setting the HTTP Server and video server (P. 56) Communication setting using RTP
  • Canon CR-N300 | Remote Camera Settings Guide - Page 50
    in the upper right of the Settings Page changes to [Apply and Reboot]. Click [Apply and Reboot] to apply the changes and restart the camera. Click [Clear] to revert to the previous settings. Important If switched to another settings screen without clicking [Apply] or [Apply and Reboot], changes will
  • Canon CR-N300 | Remote Camera Settings Guide - Page 51
    [System] > [Video and Audio] > [HDMI/SDI] Settings for the output signal format of the HDMI and SDI terminals. HDMI/SDI Common settings for the video output signal format for HDMI/SDI. [Video Output Configuration] The video output format is set as a combination of the video size and frame rate.
  • Canon CR-N300 | Remote Camera Settings Guide - Page 52
    vary depending on the frame frequency set in [System] > [System] > [Environment]. Mainstream Set the Mainstream video to be distributed from the camera. [Video Codec] Select the video codec type. In the following cases, the video codec is H.264. - If [System] > [Communication] > [External Connection
  • Canon CR-N300 | Remote Camera Settings Guide - Page 53
    [Framerate (fps)] of Substream 1 cannot be set to [59.94] or [50.00]. Substream 2 Settings for the video of Substream 2 to be distributed from the camera. [Video Codec] JPEG is fixed. [Video Size] 1280 x 720 is fixed. [Framerate (fps)] The set value is displayed according to the frame frequency. 53
  • Canon CR-N300 | Remote Camera Settings Guide - Page 54
    Stream] [Audio Input Mode] Select the type of microphone to connect to the camera: input terminals (INPUT N500 /MIC), input method (LINE/MIC), and with MIC MIC LINE MIC MIC Power to Microphone - Not Supported Supported - Not Supported +48V Note To use a microphone that requires phantom powering
  • Canon CR-N300 | Remote Camera Settings Guide - Page 55
    communication is temporarily interrupted by reseating of the LAN cable for example, the audio will be disconnected. In this case, reconnect the device to the camera. 55
  • Canon CR-N300 | Remote Camera Settings Guide - Page 56
    port] or [HTTPS port] settings are changed, and the connection to the camera from the active web browser may become disabled. If the changed settings are Clients] Enter the maximum number of clients that can connect to the camera simultaneously. If [0] is entered, only the administrator is allowed to
  • Canon CR-N300 | Remote Camera Settings Guide - Page 57
    [System] > [Server] > [RTP] Settings for video and audio streaming using RTP. RTP Server Settings for use of RTP, RTSP authentication method and port number. [RTP] Select whether to use RTP. [RTSP Authentication Method] Select a RTSP authentication method. Since RTSP authentication method is set
  • Canon CR-N300 | Remote Camera Settings Guide - Page 58
    RTP Mainstream, RTP Substream 1, RTP Substream 2 Settings for RTP stream distribution, to be configured for each stream. [Video Type] Displays [Video Codec] and [Video Size] set for each video stream in [System] > [Video and Audio] > [IP Streaming Video]. [Multicast Address] Enter multicast address
  • Canon CR-N300 | Remote Camera Settings Guide - Page 59
    Address], access via network may not be possible. In such a case, search cameras using the Camera Search Tool, and set the address again. [IPv4 Address Settings Method] Select the IPv4 address settings method. For [Manual], enter a fixed IPv4 address to [IPv4 Address]. For [Auto (DHCP)], a value
  • Canon CR-N300 | Remote Camera Settings Guide - Page 60
    subnet mask value specified for each network. [IPv4 Default Gateway Address] When [IPv4 Address Settings Method] is [Manual], enter a value. Make sure to set, when connecting the camera to a subnet different from IP connection device such as controller. [AutoIP] Select whether to use AutoIP. When
  • Canon CR-N300 | Remote Camera Settings Guide - Page 61
    Server will be displayed. [Host Name] The host name of the camera can be registered with alphanumeric characters to the name server. [Search multicast DNS. When using mDNS, IP address and host name information of the camera is notified to other hosts on the network. [mDNS] Select whether to use
  • Canon CR-N300 | Remote Camera Settings Guide - Page 62
    [System] > [Communication] > [Wireless LAN] Settings for the access point for directly connecting the camera and the wireless LAN supported devices. By setting different IP addresses for the Wireless LAN and the Wired LAN, it possible to choose and use according the purposes. Interface Settings
  • Canon CR-N300 | Remote Camera Settings Guide - Page 63
    [IPv4 Address] Enter the fixed IPv4 address. [Subnet Mask] Enter specified subnet mask value for each network. Note The wireless connection must be on a different subnet than the wired LAN. If the specified IP address is in the same subnet as the wired LAN, an error occurs. 63
  • Canon CR-N300 | Remote Camera Settings Guide - Page 64
    IP Settings Network Settings] Select whether to allow to change the network settings of the camera from the controller. NDI|HX Settings for exchanging data with NDI|HX supported devices. [NDI|HX] Select whether to use [NDI|HX] as the communication protocol. For setting to [Enable], go to [System
  • Canon CR-N300 | Remote Camera Settings Guide - Page 65
    only and cannot pass through the router. [Group Settings] Select whether to use the group settings. When a group name to which the camera belongs is specified, the camera connects only to NDI clients with the same group name. [Group Name], [Group List] Enter the group name. By clicking [Add], the
  • Canon CR-N300 | Remote Camera Settings Guide - Page 66
    ] > [External Connection (Serial)] Settings for communication by the serial connection of controllers, etc. Note Connect the Remote Camera Controller RC-IP100 via IP. This camera cannot be controlled by the serial connection. Serial Port Detail settings for the serial port. [Serial Port] Select
  • Canon CR-N300 | Remote Camera Settings Guide - Page 67
    ) Settings for connection with standard serial communication. [Standard Communication (Serial)] Select whether to use standard serial communication. [Serial Device Address] Select the address of the camera. When [Auto] is selected, addresses will be automatically assigned. 67
  • Canon CR-N300 | Remote Camera Settings Guide - Page 68
    [System] > [Security] > [Certificate Management] Manage server certificates. It is also possible to create a self-signed certificate to use, for example, for operation test. Server Certificate Management Manage the server certificates. [Server Certificates] Perform this operation to import server
  • Canon CR-N300 | Remote Camera Settings Guide - Page 69
    Validity Period] Displays the validity period of the selected certificate. Note Depending on the server certificate used by the camera and the computer connected to the camera, it may be necessary to install the root certificate, the intermediate CA certificate, or the certificate selected and
  • Canon CR-N300 | Remote Camera Settings Guide - Page 70
    as from a controller. "Administrator", "authorized user", and "guest user" are the three types of accounts that are able to access the camera. For the minimum user settings and permissions required, refer to "Measures Suitable to the Users' Environment 1: User Management" (P. 114). Administrator
  • Canon CR-N300 | Remote Camera Settings Guide - Page 71
    User Authority Set the privileges for authorized users and guest users. This setting enables to set access restrictions for the Settings Page. [Camera Control], [Video Distribution] Select the items for granting users privileges. An authorized user has higher privileges than a guest user. Important
  • Canon CR-N300 | Remote Camera Settings Guide - Page 72
    [System] > [Security] > [Host Access Restrictions] Access control can be performed individually by address to access over the network. Set IPv4 and IPv6, respectively. Important • To prohibit access via a proxy server in HTTP connection, a proxy server address must be set. • If host access
  • Canon CR-N300 | Remote Camera Settings Guide - Page 73
    If set to [No], access to all ports is blocked. 73
  • Canon CR-N300 | Remote Camera Settings Guide - Page 74
    's Installation Conditions, Tally Lamp, IR Remote Controller, and Genlock. Camera Name Settings for the camera name. [Camera Name] Enter any camera name. Installation Conditions Settings for camera use suitable for the location the camera will be installed. [Video Flip] Select whether to vertically
  • Canon CR-N300 | Remote Camera Settings Guide - Page 75
    with the external video device. Use the GEN-LOCK terminal to input external sync signals (analog black burst signal or HD ternary signal) to the camera. [Genlock] Select whether to use Genlock. [Genlock Adjustment] Adjusts the H phase of the genlock in the range of approximately ±0.4 H around the
  • Canon CR-N300 | Remote Camera Settings Guide - Page 76
    Time The date and time set in the camera are displayed. Settings It is possible to change the date and time setting method, time zone and daylight saving time set at initial setting. [Settings Method] Select the date and time setting method. [Set manually] Set the desired date and time in [Date
  • Canon CR-N300 | Remote Camera Settings Guide - Page 77
    with computer time] The date and time will be synchronized with that of the computer currently accessing the camera. After clicking [Apply], [Settings Method] will change to [Set manually]. [Time Zone] is not automatically selected, so set it if necessary. Note If the NTP server IP address
  • Canon CR-N300 | Remote Camera Settings Guide - Page 78
    [System] > [System] > [Environment] Settings for the frame frequency. Environment Setting the frame frequency. [Frame Frequency (Hz)] Frame frequency can be changed by the initial settings. The HDMI/SDI output signal format and the frame rate of the IP streaming video are selected according to the
  • Canon CR-N300 | Remote Camera Settings Guide - Page 79
    [System] > [System] > [Language] Set the language to be displayed on the Settings Page. Language Select the display language. 79
  • Canon CR-N300 | Remote Camera Settings Guide - Page 80
    shifts, click [Execute] to initialize the position. [Reboot] Reboots the camera. Initialization Initialize the camera. Important • Do not turn off the power to the camera while performing [Restore Default Settings]. Turning off the camera at this stage may result in disabling its ability to boot
  • Canon CR-N300 | Remote Camera Settings Guide - Page 81
    set to [Do not save], initialization will be performed all the settings excluding camera's date and time. Since the network settings will be initialized, connection to the camera will not be enabled. Use the Camera Search Tool to configure the initial settings. Note Even if the [Network Settings
  • Canon CR-N300 | Remote Camera Settings Guide - Page 82
    used by SSL/TLS, including private key will also be restored. After restoring, the camera will be rebooted. Important • Be aware that if restored from a backup file of another camera, problems such as duplicate addresses on the network or overwriting with a different Administrator Password may
  • Canon CR-N300 | Remote Camera Settings Guide - Page 83
    information is displayed. Update Firmware Performs firmware update. Important Do not turn off the power to the camera while performing [Update Firmware]. Turning off the camera at this stage may result in disabling its ability to boot correctly. [Restore Default Settings] Updating the firmware
  • Canon CR-N300 | Remote Camera Settings Guide - Page 84
    ] > [Maintenance] > [Log] Display and download log messages. View Logs Displays the history of camera operation and connection. [System Log], [Error Log] When [View] is clicked, log messages from the time the camera was turned on is displayed. When [Download] is clicked, the message list can be
  • Canon CR-N300 | Remote Camera Settings Guide - Page 85
    Chapter IR Remote Controller This section describes the features and handling of the included IR remote controller.
  • Canon CR-N300 | Remote Camera Settings Guide - Page 86
    returning to standby. (2) PRESET Set or call a preset. If a number (1 to 10) is pressed while pressing the SET button, the current camera settings such as camera angle, zoom and focus are saved as a preset to that number. Press the number (1 to 10) to call the registered preset. Note • Registrable
  • Canon CR-N300 | Remote Camera Settings Guide - Page 87
    direction. Press the HOME button to return the camera angle to the front (home position). (5) CAMERA SELECT Press the number of the camera wanting to operate with the IR remote controller. Use the SERVICE switch on the back of the camera to set the camera number. button to change the Note If there
  • Canon CR-N300 | Remote Camera Settings Guide - Page 88
    Handling the Remote Controller  Battery Replacement Remove the battery cover on the back of the remote controller, and insert two new AAA batteries by paying attention to the + positive and - negative directions. Close the battery cover tightly until it snaps.  Precautions • If the remote
  • Canon CR-N300 | Remote Camera Settings Guide - Page 89
    This chapter explains the measures to take when trouble occurs or a log message is displayed during camera use. It also explains how to reset the USB camera function N300 or camera to the factory default settings, perform routine maintenance, major specifications and camera security measures.
  • Canon CR-N300 | Remote Camera Settings Guide - Page 90
    frequency has to be set at 59.94 Hz or 50.00 Hz (P. 78). 2 Turn off the camera once, then switch the SERVICE switch setting of the camera to USB camera. For details, refer to the "Installation Guide/Important Information". 3 Connect the camera and the computer with a USB cable. Then turn on the
  • Canon CR-N300 | Remote Camera Settings Guide - Page 91
    to. • Configure to exclude the camera, or the software where the problem occurred, in the security software. • The camera's SERVICE switch is set as a USB camera. Switch the SERVICE switch and restart the camera (Refer to "Installation Guide/Important Information"). N300 • Exceeds the maximum number
  • Canon CR-N300 | Remote Camera Settings Guide - Page 92
    abnormality occurred to the camera. Restart the camera. If the problem is still not solved, Camera] > [Installation Conditions] is set to [Video Flip] correctly (P. 74). • If connecting to a remote controller, the setting of the controller may be reverse. For details, refer to the instruction manual
  • Canon CR-N300 | Remote Camera Settings Guide - Page 93
    after rebooting, initialize to the factory default settings. If the problem persists, contact the dealer. S320 PAN/TILT operation error [err Initialization] (P. 80). If it is still not resolved, it may be a camera failure, so contact the dealer. S330 Broken Fan [err] Description FAN does
  • Canon CR-N300 | Remote Camera Settings Guide - Page 94
    frozen [crit] Description video %1 stalled (V402) %1 Video number Meaning The video input function was stopped because the video input from the camera stopped. Countermeasure If the error is still detected after rebooting, it may be a failure, so contact the dealer.  Standard communication
  • Canon CR-N300 | Remote Camera Settings Guide - Page 95
    notification number Reason for error Failed to receive audio message.  Camera application warning C211 Camera control command overflow [warning] Description command queue overflowed (C211) Meaning The camera control command queue overflowed, and some commands were discarded. Countermeasure
  • Canon CR-N300 | Remote Camera Settings Guide - Page 96
    system is not supplied [info] Description Insufficient power to boot the camera system. (S080) Meaning The power required to start the camera system is not being supplied. Countermeasure Use a DC or PoE+ supported L2 switch as the power source. S046 Connect a device through a wireless LAN
  • Canon CR-N300 | Remote Camera Settings Guide - Page 97
    user=, prio=(W030) W (wvhttp session | V (Session-less video client) | N (Session-less event client) +: Connect, -: Disconnect The camera server client was connected or disconnected. W031 Transmitted video data size [info] Description %1 Meaning %1= host=, user=, video
  • Canon CR-N300 | Remote Camera Settings Guide - Page 98
    connection time settings used when connecting. 43: Reconnect or restart. 45: Use supported client software. 47: Check user level used when connecting. 49: Check denial type is the same with B102).  Camera application notification C001 Camera control module started/ stopped [info] Description %1
  • Canon CR-N300 | Remote Camera Settings Guide - Page 99
     NDI|HX notification P001 Starting and stopping of NDI|HX [info] Description %1 %1 NDI|HX (P001) starting | stopping Meaning The NDI|HX started/stopped. 99
  • Canon CR-N300 | Remote Camera Settings Guide - Page 100
    via the network is not possible. In this case, press the RESET switch to reset the camera. 1 Turn the camera off. The camera does not have a power switch. In order to turn the camera on or off, connect or disconnect the power supply cable. 2 Turn on the power while pushing the RESET switch, confirm
  • Canon CR-N300 | Remote Camera Settings Guide - Page 101
    N300 RESET Switch POWER Lamp 101
  • Canon CR-N300 | Remote Camera Settings Guide - Page 102
    Black:Master Pedestal Black:Master Black Red Black:Master Black Blue Black Gamma:Level Black Gamma:Range Black Det. & Tracking Normal Item AF Response Focus Limit • PTZ/IS Digital Zoom Pan/Tilt Acceleration Soft Zoom Control N300 Image Stabilizer System Item • HDMI/SDI Video Output Configuration •
  • Canon CR-N300 | Remote Camera Settings Guide - Page 103
    IPv6 IPv6 Enable Auto (RA) Enable Auto (DHCPv6) Enable IPv6 Address (Manual) (Blank) Prefix Length 64 IPv6 Default Gateway Address (Blank) IPv6 Address Command Response Method Use Source Port Number Camera IP Settings Inquiry Allow Camera IP Settings Network Settings Do Not Allow
  • Canon CR-N300 | Remote Camera Settings Guide - Page 104
    • IPv6 Host Access Restrictions Apply Host Access Restrictions • Camera Name Camera Name • Installation Conditions Video Flip • Tally Lamp Tally Lamp Firmware Restore Default Settings 104 Factory Default Settings Enable Disable Set manually (GMT+09:00) Osaka, Sapporo, Tokyo Disable 59.94 Save
  • Canon CR-N300 | Remote Camera Settings Guide - Page 105
    Routine Maintenance Before any maintenance, turn off the power. Cleaning the External Surface 1 Wet a soft cloth with water or a mild detergent and lightly wipe off any dirt. 2 Wipe with a dry cloth. Cleaning the Lens Use a commercial lens cleaner to remove grime on the lens surface. • Scratches on
  • Canon CR-N300 | Remote Camera Settings Guide - Page 106
    Specifications For the latest information on this product (firmware and software, user manuals, operating environment, etc.), refer to the Canon website. CR-N500 Main Unit  Camera Image Sensor Lens Digital Zoom Lens Configuration Minimum Focusing Distance Angle of View Shutter Speed Iris Gain ND
  • Canon CR-N300 | Remote Camera Settings Guide - Page 107
    When frame frequency is 29.97/25.00 Hz: 12.50 fps XC (Canon's original), RTSP/RTP, NDI|HX, RTMP/RTMPS, Standard Communication (Serial), -in power supported) Sensitivity (MIC): -72 dBV (Manual volume center, full scale -18 dB)/1 k or more/Att.: 20 dB Sensitivity (LINE): -10 dBV (Manual volume center,
  • Canon CR-N300 | Remote Camera Settings Guide - Page 108
    Consumption Dimensions (W x H x D) Weight Supported Controllers Temperature: 0°C - +40°C (+32 -IP100 Software: Remote Camera Control Application CR-N300 Main Unit  Camera Image Sensor Lens Digital K), Manual * Color temperatures are given for reference purposes only. Focus mode: Manual, Continuous
  • Canon CR-N300 | Remote Camera Settings Guide - Page 109
    00 fps, 5.00 fps 50.00 Hz: 12.50 fps, 5.00 fps XC (Canon's original), RTSP/RTP, NDI|HX, RTMP/RTMPS, Standard Communication (Serial), Standard Communication Ø3.5 mm stereo mini jack (unbalanced, plug-in power supported) Sensitivity (MIC): -72 dBV (Manual volume center, full scale -18 dB)/1 k or more
  • Canon CR-N300 | Remote Camera Settings Guide - Page 110
    Power Supply Power Consumption Dimensions (W x H x D) Weight Supported Controllers Temperature: 0°C - +40°C (+32°F - +104°F) kg (4.86 lb.) (body only) Hardware: RC-IP100 Software: Remote Camera Control Application Accessories  Compact Power Adapter Input Rate Output Rate Temperature for Use
  • Canon CR-N300 | Remote Camera Settings Guide - Page 111
    iOS 14.2.1, iPadOS 14.2 Safari - Must be configured to allow use of JavaScript, and web storage - Only JPEG format is supported for displaying video - Does not support audio  Camera Search Tool OS CPU Memory Display Windows 10 64-bit Intel Core i7-4700 or greater 8 GB or more Resolution 1920
  • Canon CR-N300 | Remote Camera Settings Guide - Page 112
    according to the environment under the customer's responsibility, which will lead to safer camera operation. System administrators are advised to read. Important To the full extent permitted by laws and regulations, neither Canon Inc. nor any of its subsidiaries or affiliates shall be liable for any
  • Canon CR-N300 | Remote Camera Settings Guide - Page 113
    to always keep it updated because the measures against known vulnerabilities are applied to the latest firmware. Check Canon's website regularly at the initial setting after purchasing the camera and during its operation, whether the latest firmware is provided. The firmware version can be confirmed
  • Canon CR-N300 | Remote Camera Settings Guide - Page 114
    is necessary to be careful to give authority to authorized users. Regularly review and manage the authorized users, and set the minimum necessary authorization level and set on the camera's Settings Page respectively (P. 56, 57). Confirm that the application supports the Digest Authentication. 114
  • Canon CR-N300 | Remote Camera Settings Guide - Page 115
    , it is necessary to deal with the whole system. Measures Suitable to the Users' Environment 6: Disabling Unused Functions The camera has functions to support various purposes and network environments. However, unless those functions are properly set, there is a risk of unauthorized access from
  • Canon CR-N300 | Remote Camera Settings Guide - Page 116
    data can be delivered to the specified multicast address. It is recommended to set [RTP] to [Disable] when the devices connecting to the camera do not require RTP protocol. Standard Communication (IP), NDI|HX, RTMP When using [Standard Communication (IP)] (P. 64), [NDI|HX] (P. 64), and [RTMP] (P. 65
  • Canon CR-N300 | Remote Camera Settings Guide - Page 117
    (RTP 57 Authorized User 70 Authorized User Account 71 Auto Slow Shutter 30 Autofocus 37, 42 B Backup/Restore 82 Bit Rate Control 53 Black 35 C Camera Name 74 Camera Search Tool 15, 17 Certificate Management 68 Color Matrix 31, 34 Color Space 34 Create Certificate 68 D Date and Time 76
  • Canon CR-N300 | Remote Camera Settings Guide - Page 118
    Manual Focus 40, 44 N ND Filter 28 NDI|HX 64 Network 59 Noise Reduction 35 Notification log 96 O Operating Environment 110 P Pan 25 Power ON 23 Preset 46 PTZ 45 R Remote Camera Lamp 23, 74 Tilt 25 Troubleshooting 91 U Update Firmware 83 USB Camera 90 User Authority 71 User Management
  • Canon CR-N300 | Remote Camera Settings Guide - Page 119
    BIE-7284-002 © CANON INC. 2021
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
This document should be read before using the product.
ENGLISH
Remote Camera
S
ettings Guide