Canon DR-X10C User Manual

Canon DR-X10C - imageFORMULA - Document Scanner Manual

Get Canon DR-X10C - imageFORMULA - Document Scanner PDF manuals and user guides
UPC - 013803087666
View all Canon DR-X10C manuals
Add to My Manuals
Save this manual to your list of manuals

Canon DR-X10C manual content summary:

  • Canon DR-X10C | User Manual - Page 1
    User Manual Please read this manual before using the scanner. After you finish reading this manual, keep it in a safe place for future reference.
  • Canon DR-X10C | User Manual - Page 2
    Document Scanner, Model M11063 This device complies with Part accordance with the instructions, may cause harmful manual. If such changes or modifications should be made, you could be required to stop operation of the equipment. Canon U.S.A. Inc. One Canon and dissemination of products with functions
  • Canon DR-X10C | User Manual - Page 3
    the Document Scanner. DR-X10C: Model M11063 Trademarks • Canon and the Canon logo are registered trademarks of Canon Inc. in the United States and may also be trademarks or registered trademarks in other countries. • imageFORMULA is a trademark of Canon Electronics Inc. • Microsoft and Windows are
  • Canon DR-X10C | User Manual - Page 4
    , and troubleshooting. The Software section describes how to use the ISIS/ TWAIN driver with the scanner, and how to set up job registration tools. CapturePerfect 3.0 Operation Guide (Electronic Manual) This is the operation guide for CapturePerfect 3.0, the Canon document scanner application
  • Canon DR-X10C | User Manual - Page 5
    are used in this manual to explain procedures, restrictions, handling precautions, and instructions that should be observed for safety. WARNING Indicates a warning concerning operations that may lead to death or injury to persons if not performed correctly. To use the scanner safely, always pay
  • Canon DR-X10C | User Manual - Page 6
    cleaning and roller replacement Chapter 6 Practical Examples Describes displayed messages and troubleshooting solutions Chapter 7 Appendix Provides a list of specifications and support information ■ Software Chapter 8 ISIS/TWAIN Driver Settings Describes the settings for the ISIS/TWAIN driver
  • Canon DR-X10C | User Manual - Page 7
    User Manual Hardware Please read this manual before using the scanner. After you finish reading this manual, keep it in a safe place for future reference.
  • Canon DR-X10C | User Manual - Page 8
    Rollers with a Cleaning Sheet 5-4 Cleaning the Glass 5-5 Cleaning the Platen Rollers 5-6 Cleaning the Pickup and Feed Rollers 5-7 Cleaning the Retard Roller 5-9 2. Replacing the Transport Rollers 5-12 Roller Replacement Cycle 5-12 Checking and Resetting the Page Counter ........ 5-13 ii
  • Canon DR-X10C | User Manual - Page 9
    Display 6-2 Error Messages 6-3 2. Troubleshooting 6-5 Trouble Categories 6-5 Problem and Solution 6-5 3. Uninstalling the Software 6-9 Uninstalling the ISIS/TWAIN Driver 6-9 Chapter 7 Appendix 1. Specifications 7-2 Unit Specifications 7-2 Options 7-4 Consumables 7-4 External Dimensions
  • Canon DR-X10C | User Manual - Page 10
    Chapter 1 Before You Start Using the Scanner 1. Important Safety Instructions 1-2 Installation Location 1-2 Power 1-2 Moving the Scanner 1-3 Handling 1-3 Disposal 1-5 2. Features 1-6 3. Names and Functions of Parts 1-10 Front View, Feeder Inlet, and Eject Outlet ..........1-10 Rear View 1-
  • Canon DR-X10C | User Manual - Page 11
    Chapter 1 Before You Start Using the Scanner 1. Important Safety Instructions To ensure the safe operation of this scanner, be sure to read the safety warnings and precautions described below. Installation Location The performance of this scanner is affected by the environment in which it is
  • Canon DR-X10C | User Manual - Page 12
    than the power cord provided with this scanner. ■ Never try to take the scanner apart or modify it in any way, as this is dangerous and may lead to a fire or electric shock. ■ Do not use flammable aerosol sprays products near the scanner. ■ When cleaning the scanner, turn the power switch OFF and
  • Canon DR-X10C | User Manual - Page 13
    power switch OFF, and disconnect the power plug from the power outlet. Then, contact your local authorized Canon dealer or service representative to have the unit serviced. ■ Do not locate the scanner in a humid or dusty location. Doing so may cause a fire or electric shock. ■ Do not place objects
  • Canon DR-X10C | User Manual - Page 14
    result in personal injury. Be extra careful of neckties and long hair. If anything becomes caught in the scanner, immediately disconnect the power cord to stop the scanner. ■ Be careful when placing paper in the scanner and when removing jammed paper. It is possible to cut your hand on the edge of
  • Canon DR-X10C | User Manual - Page 15
    The main features of the DR-X10C are described below. Scanner Features ● Fast Document Feeding The scanner can scan up to 100 document sheets per minute of LTR/A4-size paper in black and white, grayscale, and color scanning modes. * Scanning conditions: LTR/A4 portrait, duplex, 200 dpi ● Variety of
  • Canon DR-X10C | User Manual - Page 16
    Auto Image Type Detection The scanner automatically detects whether documents are in black and white or color. ● Auto Paper Size Detection The document page size is detected before scanning. Fixed-Size Scanning Auto-Size Detection Scanning ● Skew Detection Function The scanner stops feeding when
  • Canon DR-X10C | User Manual - Page 17
    create two images with different scanning conditions from a single scan pass. However, this function is only available when using CapturePerfect 3.0 (supplied with the scanner) or another application program that supports the MultiStream function. Document to be Scanned (150 dpi, Color) (300 dpi
  • Canon DR-X10C | User Manual - Page 18
    ● Barcode Detection (Option) Barcodes on documents can be detected by installing the optional barcode module. Chapter 1 Before You Start Using the Scanner ● Patchcode Support (Option) By installing the optional patchcode decoder, patch code sheets inserted between document pages can be detected for
  • Canon DR-X10C | User Manual - Page 19
    You Start Using the Scanner 3. Names and Functions of Parts The names and functions of the DR-X10C parts are shown below. Front View, Feeder Inlet, and Eject Outlet a Document Eject Tray Scanned documents are output here. (See p. 3-11.) b Document Feed Tray Load documents to be scanned. (See
  • Canon DR-X10C | User Manual - Page 20
    c DIP Switch (SCSI ID) Selects the scanner's SCSI ID. (See p. 2-8.) d user mode and job. d Menu Key Displays the user mode. e Job Key Displays jobs. f Count Only Key Feeds and counts the number of document pages. g Bypass Mode Key Raises the document holder for the non-separating (manual
  • Canon DR-X10C | User Manual - Page 21
    2-2 2. Installation Requirements 2-3 3. Software Installation 2-4 About the Setup Menu 2-4 4. Connecting the Scanner to the Computer ....... 2-6 Interface Connector Locations 2-6 Connecting the Scanner to the Computer 2-6 5. Turning the Power ON (Scanner Recognition 2-9 About the Power Switch
  • Canon DR-X10C | User Manual - Page 22
    you connect the scanner to the computer before installing the software, a wizard screen such as the one shown below will appear when you turn the scanner ON. In this case, click [Cancel] to close the wizard screen, and then turn the scanner OFF. • Windows 2000 • Windows XP • Windows Vista Chapter
  • Canon DR-X10C | User Manual - Page 23
    reduced and transmission may take a long time. • Even if the computer satisfies the recommended specifications, the scanning speed may vary, depending on the scan settings. • The ISIS/TWAIN Drivers provided with the scanner do not necessarily operate on all ISIS- or TWAIN-compatible applications
  • Canon DR-X10C | User Manual - Page 24
    account with Administrator privileges. • When using Windows Vista, the "User Account Control" dialog box may appear. In this case, enter your login user password for Administrator privileges, and click [OK]. Hint See the Easy Start Guide for instructions on using the typical installation procedure
  • Canon DR-X10C | User Manual - Page 25
    the selected software. ■ The Read Manual Screen From this screen you can select one of the supplied electronic manuals to read: the Easy Start Guide (a printed copy is also supplied), the Reference Guide, the User Manual (this manual), or the CapturePerfect 3.0 Operation Guide. Chapter 2 Setup 2-5
  • Canon DR-X10C | User Manual - Page 26
    the Computer There are two methods for connecting the DR-X10C scanner to a computer: a USB connection to a a USB Connection 1. Connect the supplied power cord into the power connector on the back of the scanner. a 2. Connect the power cord into an AC outlet. b a USB Connector b SCSI Connector
  • Canon DR-X10C | User Manual - Page 27
    computer is turned OFF before connecting the SCSI cable. If the cable is connected while the computer is on, the scanner may not be properly recognized by the computer. 1. Shut down Windows and turn the computer's power OFF. 2. Connect the supplied power cord into the power connector on the back of
  • Canon DR-X10C | User Manual - Page 28
    in the system. DIP Switches Default Position (SCSI ID=2) • The DR-X10C scanner incorporates a SCSI terminator which is permanently set to ON. When using a daisy-chain configuration with other SCSI devices, make sure that the DRX10C scanner is connected as the last device in the chain. Set the
  • Canon DR-X10C | User Manual - Page 29
    and the scanner, the Windows Plug and Play function recognizes the scanner and automatically installs the required device driver. About the Power Switch When the power switch (located at the lower left side of the front of the scanner) is turned ON, the Document Feed Tray opens automatically
  • Canon DR-X10C | User Manual - Page 30
    The DR-X10C device driver is installed in Device Manager under [Imaging Devices] as [CANON DR-X10C USB] or [CANON DR-X10C SCSI]. • With Windows XP open [System] and click [Device Manager] on the Hardware tab sheet. - With Windows Vista, open [System Maintenance] and click [Device Manager]. Or,
  • Canon DR-X10C | User Manual - Page 31
    the Document Feed Tray 3-7 Adjusting the Document Guides 3-9 Preparing the Document Eject Tray 3-11 4. Document Feeding Methods 3-12 Selecting the Document Feeding Method ...........3-12 5. Scanning 3-14 About the Job Function 3-14 CapturePerfect 3.0 3-15 6. Using Patchcode Sheets (Option
  • Canon DR-X10C | User Manual - Page 32
    DR-X10C scanner ON and OFF, or if you are using a USB connection, you can set the USB-linked power switch. CAUTION • After turning the scanner scanner) is turned ON, the Document Feed Tray opens automatically. (See p. 3-7.) 1. Press the Menu key on the control panel. Menu Key Power Switch The User
  • Canon DR-X10C | User Manual - Page 33
    4. Press [Enter]. Enter Key The current setting is indicated by blinking square brackets [ ]. 5. Press the [ ] or [ ] key to select [ON] or [OFF], and press [Enter] to accept the selection. 6. Press the Stop key to exit the User Mode. Chapter 3 Basic Operation 3-3
  • Canon DR-X10C | User Manual - Page 34
    can cause the scanner to jam. • Always make sure that the ink on a document is dry before scanning it. Scanning documents with the ink still wet may soil the rollers or scanning glass, cause lines or smudges to appear on images, or dirty other documents. • Always clean the rollers or scanning glass
  • Canon DR-X10C | User Manual - Page 35
    • To use the Long Document Mode, feed document pages manually, one after another. ■ Long Document Mode Setting Using the Long Document mode, pages up to 118.1" (3 m) long can be scanned with automatic paper size detection. You can set the Long Document Mode setting from the User Mode. 1. Press the
  • Canon DR-X10C | User Manual - Page 36
    • Some scanning mode and resolution settings may produce incomplete page images. In this case, try decreasing the resolution or, if scanning in color mode, switch to black and white. • If a sheet is loaded at a skewed angle when scanning long documents, it may be damaged by contacting both sides of
  • Canon DR-X10C | User Manual - Page 37
    desired paper size. Preparing the Document Feed Tray ■ Opening the Document Feed Tray When the scanner is turned ON, the Document Feed Tray opens automatically and moves to the specified home position height. 1. Press the Menu key on the control panel. Menu Key The User Mode is activated. Hint
  • Canon DR-X10C | User Manual - Page 38
    Press the Stop key to exit the User Mode. ■ Closing the Document Feed Tray To close the Document Feed Tray, lift it gently so that the sides of the tray hook into the scanner body, then press it in at both sides. ■ Document Guides Unlock the document guides by gently pressing both sides of either
  • Canon DR-X10C | User Manual - Page 39
    the left or right of center by locking the document guides at the appropriate positions. Locking the Document Guides 2. Load your documents against the left feed guide. 3. Lock the left document guide (a) by pulling out the lock lever, then slide the right document guide to the right edge of your
  • Canon DR-X10C | User Manual - Page 40
    4. Lock the right document guide (a), and unlock the left document guide (b). Chapter 3 Basic Operation 2. Lock the left document guide (a), and unlock the right document guide (b). 5. Slide the left document guide to the left edge of your documents. 3. Slide the right document guide all the way
  • Canon DR-X10C | User Manual - Page 41
    Tray Extension and Eject Paper Stopper, to be adjusted to match the length of your documents. ■ Document Guides Slide the document eject guides to match the width of your documents. Chapter 3 Basic Operation ■ Document Eject Tray Extension Pull out the tray extension to match the length of your
  • Canon DR-X10C | User Manual - Page 42
    be positioned manually for transport by the feed roller, while the pickup roller is disabled. Selecting the Document Feeding Method Continuous Feeding is the default feeding method, but Manual Feeding can be enabled by selecting Manual Feeding as the Feeding Option for the ISIS/TWAIN driver, or by
  • Canon DR-X10C | User Manual - Page 43
    Retard Roller IMPORTANT When the Continuous Manual Feeding Mode is set to ON from the User Mode, make sure to disable it (set to OFF) when finished scanning. Otherwise, normal continuous feeding will be disabled the next time someone uses the scanner. Hint For Manual Feeding, you must feed document
  • Canon DR-X10C | User Manual - Page 44
    software included with the scanner, or directly from the control panel of the DR-X10C, using the Job image data processing settings for each job to be used with the Job Function. Hint The Job Registration Tool is a TWAIN-compliant application that is installed along with the ISIS/TWAIN driver
  • Canon DR-X10C | User Manual - Page 45
    is an ISIS-compatible application developed for Canon document scanners. CapturePerfect 3.0 includes the following modes. Select the desired scan mode from the Scan menu to perform scanning. For more information on CapturePerfect 3.0, refer to the CapturePerfect 3.0 Operation Guide. ■ Scanning with
  • Canon DR-X10C | User Manual - Page 46
    Basic Operation CapturePerfect 3.0 starts. 2. From the [Scan] menu, select [Select Scanner]. The [Select Scanner] dialog box opens. 3. Select [Canon DR-X10C] and click [Settings]. IMPORTANT If [Canon DR-X10C] is not displayed in the list of scanners, you must re-install the ISIS/TWAIN driver. 3-16
  • Canon DR-X10C | User Manual - Page 47
    ISIS driver properties dialog box, that setting is applied here. 5. Click [OK] to finish scanner selection. 6. From the [Scan] menu, select [Scanner The Properties dialog box for the ISIS driver opens. 9. Specify the file name and the file type for saving the image data. For details on the available
  • Canon DR-X10C | User Manual - Page 48
    Scanning dialog box. Bypass Mode Key • If a Feed Option other than [Standard Feeding] or [Manual Feeding] is selected, once you have started scanning, each document placed in the Document Feed Tray is scanned, and when no document is loaded, the scanner enters the standby state. 12. When scanning
  • Canon DR-X10C | User Manual - Page 49
    3 Basic Operation 6. Using Patchcode Sheets (Option) When the optional patchcode decoder is installed, the DR-X10C supports Automatic File Separation by detecting patchcode sheets inserted within a document, and performs batch separation. About Patchcode Sheets Patchcode patterns are printed on
  • Canon DR-X10C | User Manual - Page 50
    before placing the documents on the scanner. Insert patchcode sheets in front of the documents you want to save as separate files. 3. On the [Other] tab of the ISIS driver properties, select [Patchcode] from the Batch Separation drop-down list. IMPORTANT If the patchcode decoder is not installed
  • Canon DR-X10C | User Manual - Page 51
    , raise the upper unit slightly to remove it. 5. Check to verify the last saved image, and resume scanning. ■ When "Press Start Key" Appears When the Rapid Recovery System is enabled in the ISIS/ TWAIN driver settings, the following message appears on the display panel after you remove the jammed
  • Canon DR-X10C | User Manual - Page 52
    When a double feed is detected, the following process occurs, and messages appear according to the Rapid Recovery System setting in the ISIS/TWAIN driver. (See "[Rapid Recovery System] Check Box" on p. 8-17.) Start Key IMPORTANT • When you press the Start key, the image of the document page that
  • Canon DR-X10C | User Manual - Page 53
    file, and ends the scan process. In this case, restart scanning from the document page where the double feed occurred, or from the beginning. When detecting double feeds by document length When detecting double feeds ultrasonically [IGNORE]: Saves the image of the page that was detected as a double
  • Canon DR-X10C | User Manual - Page 54
    Chapter 4 Other Functions 1. Other Functions and Settings 4-2 2. Function Description 4-4 3. User Mode 4-9 User Mode Operating Procedure 4-9 4. User Mode Functions 4-11
  • Canon DR-X10C | User Manual - Page 55
    -Feed Detection Double-Feed Detection (Count-Only Mode) Double-Feed Retry Staple Detection Staple Detection (Count-Only Mode) Staple Detection Level Setting Stand-by Mode Long-Document Mode Torque Control Tray Position Selectable Background Operation/Setting Method Panel Operation User Mode ISIS
  • Canon DR-X10C | User Manual - Page 56
    Folio Scan Buzzer (Beeper) Control Verify Scan Manual Feed Mode Frame Detection Error Mode Operation/Setting Method Panel Operation User Mode ISIS/TWAIN - - ✔ - ✔ - ✔ User Mode: The scanner function setting is made as a User Mode selection. ISIS/TWAIN: The function is an ISIS/TWAIN driver
  • Canon DR-X10C | User Manual - Page 57
    Function Description The Other Functions are described below. See "User Mode" on p. 4-9, for descriptions of the functions set from the User Mode. ■ Count-Only Mode Counts the number of loaded document sheets by simply feeding them through the scanner. Hint The Count-Only mode is executed by the
  • Canon DR-X10C | User Manual - Page 58
    reaching the specified count ■ Double-Feed Detection Function The scanner can detect double feeds. Two detection methods are used: comparison of document lengths, and ultrasonic detection of spacing between documents, which is set in the ISIS/TWAIN driver. Chapter 4 Other Functions IMPORTANT • When
  • Canon DR-X10C | User Manual - Page 59
    side. (See "Adjusting the Document Guides" on p. 3-9.) • Be careful to keep the staple detection window glass clean, and wipe the glass if dust is present. Hint • Staple detection is controlled in the ISIS/TWAIN driver, and the detection level can be set in the User Mode. (See "Staple Detection
  • Canon DR-X10C | User Manual - Page 60
    the black or white part of the rollers, according to the selection specified in the ISIS/TWAIN driver. Platen Rollers (Black/White Background Rollers) Black White Brush IMPORTANT Image processing performance depends on the selected background (black or white). (See "Background Color" on p. 8-18
  • Canon DR-X10C | User Manual - Page 61
    the scanner OFF, wait at least 10 seconds before turning it back ON. Scanning Unit Hint • The text to print and the printing position can be specified in the ISIS/TWAIN driver. (See p. 8-24.) • Even if the post-imprinter is not installed, you can add a specified text string onto scanned images
  • Canon DR-X10C | User Manual - Page 62
    with the capability to change certain scanner functions. User Mode Operating Procedure User Mode operations are controlled by the following procedure. Hint Operating procedures differ according to User Mode function. For details, refer to the indicated pages. 1. Press the Menu key on the control
  • Canon DR-X10C | User Manual - Page 63
    3. Press [Enter]. Enter Key The current setting is indicated by blinking square brackets [ ]. 4. Press the [ ] or [ ] key to select [ON] or [OFF], and press [Enter] to accept the selection. Chapter 4 Other Functions 4-10
  • Canon DR-X10C | User Manual - Page 64
    level. [1] is the default setting, [2] provides higher sensitivity, and [0] provides lower sensitivity. ■ Long Document Mode Setting When a double feed is detected with Ultrasonic doublefeed detection, the Double-Feed Retry function transports the double fed pages back to the feeder inlet and tries
  • Canon DR-X10C | User Manual - Page 65
    Manual Feeding Mode Setting This mode disables automatic feeding by the pickup roller, so that the loaded document stack must be fed by hand one sheet at a time by the operator. (See "Continuous Manual Feeding the normal display), clean the scanning glass. Use to adjust display panel contrast. 4-
  • Canon DR-X10C | User Manual - Page 66
    Torque Setting This setting adjusts the torque (force of rotation) of the retard roller when the scanner's capability of separating document pages has degraded due to roller wear, or when feeding materials that do not feed easily, such as thin paper. The default setting is [3]. To increase torque
  • Canon DR-X10C | User Manual - Page 67
    imprinter is installed, this function executes a test printing of the imprinter. (See "Performing an Imprinter Test" on p. 5-20.) ■ Cleaning Mode This function executes roller cleaning using a cleaning sheet. (See "Cleaning Rollers with a Cleaning Sheet" on p. 5-4.) Chapter 4 Other Functions 4-14
  • Canon DR-X10C | User Manual - Page 68
    with a Cleaning Sheet 5-4 Cleaning the Glass 5-5 Cleaning the Platen Rollers 5-6 Cleaning the Pickup and Feed Rollers 5-7 Cleaning the Retard Roller 5-9 2. Replacing the Transport Rollers 5-12 Roller Replacement Cycle 5-12 Checking and Resetting the Page Counter.........5-13 3. Imprinter Ink
  • Canon DR-X10C | User Manual - Page 69
    a cloth dampened with water or mild detergent solution. Wring out the cloth thoroughly, and use a clean dry cloth to wipe the scanner dry. IMPORTANT • To open the imprinter cover, adjust the Document Feed Guides outward and press the tab (indicated by the arrow in the illustration) to unlock the
  • Canon DR-X10C | User Manual - Page 70
    Cleaning the Glass and Rollers If scanned images contain spots or documents become dirty after scanning, the scanning glass or transport rollers inside the scanner may be dirty. The locations of the main glass and rollers are as follows. Pickup Rollers Feed Rollers Platen Roller Scanning
  • Canon DR-X10C | User Manual - Page 71
    using a cleaning sheet. Hint • Each cleaning sheet is used several times to clean one side of the rollers. • Cleaning sheets can be purchased as consumables. For details, contact your local authorized Canon dealer or service representative. Product Name: Cleaning Sheets (package of 30) Product Code
  • Canon DR-X10C | User Manual - Page 72
    cleaning sheet to clean the same side of the rollers. 9. Prepare a new cleaning sheet, and clean the other side in the same way. IMPORTANT • When placing the adhesive side down, make sure to support the cleaning sheet while inserting it into the feed inlet so that it does not touch the Document Feed
  • Canon DR-X10C | User Manual - Page 73
    the upper and lower sides of the scanning glass to brush away dust as the rollers turn before scanning, and to provide the selected background (white or black) for document images. Clean the platen rollers periodically using the following procedure. Stop Key Each time you press the Stop key, the
  • Canon DR-X10C | User Manual - Page 74
    the sheet over the roller. The location of the sheet for the lower platen roller is in front of the roller. Sheet (avoid bending) Chapter 5 Maintenance Cleaning the Pickup and Feed Rollers Use the following procedure to remove and reinstall the pickup and feed rollers during cleaning or replacement
  • Canon DR-X10C | User Manual - Page 75
    the feed roller. ■ Reinstalling Pickup and Feed Rollers 1. Set the pickup roller (a) in place and push the mounting lever (b) back to secure it. 5. Remove the feed roller. 2. Align the notches in the shaft of the feed roller with the pins on the shaft in the scanner, and place the feed roller
  • Canon DR-X10C | User Manual - Page 76
    Do not use excessive force when removing or reinstalling the retard roller. Doing so could damage the roller, resulting in feed errors. ■ Removing and Cleaning the Retard Roller 1. Carefully raise the upper unit until it stops. 2. Grasp the roller cover with your fingers, and pull it up to remove it
  • Canon DR-X10C | User Manual - Page 77
    it to the left (b) to unlock the roller. Chapter 5 Maintenance ■ Reinstalling the Retard Roller 1. Set the retard roller into place in the scanner. 4. Remove the retard roller. 2. Align the notches in the roller with the shaft pins in the scanner, then slide the roller lock lever in the direction
  • Canon DR-X10C | User Manual - Page 78
    4. Replace the roller cover. 5. Push the front of the roller cover in until it clicks into place. 6. Carefully lower the upper unit (a). Press down on both sides of the upper unit to ensure that it is securely closed.(b) Chapter 5 Maintenance 5-11
  • Canon DR-X10C | User Manual - Page 79
    . ■ Roller Replacement Kit The Roller Replacement Kit consists of replacement pickup, feed, and retard rollers. For details, contact your local authorized Canon dealer or service representative. Product Name: Roller Replacement Kit Product Code: 2418B001 Pickup Roller IMPORTANT • When the roller
  • Canon DR-X10C | User Manual - Page 80
    by the currently installed feed rollers. Make sure to reset the counter when you replace the rollers. • The Total Counter shows the total number of pages fed over the life of the scanner, and cannot be reset. 1. Press the Menu key on the control panel to activate the User Mode. The counter reset
  • Canon DR-X10C | User Manual - Page 81
    details, contact your local authorized Canon dealer or service representative. Product Name: Ink Cartridge (Blue) Product Code: 3693A002 (C6602B) Product Name: Ink Cartridge (Red) Product Code: 3693A003 (C6602R) Product Name: Ink Cartridge (Green) Product Code: 3693A004 (C6602G) IMPORTANT • Spare
  • Canon DR-X10C | User Manual - Page 82
    (Pre-Imprinter) IMPORTANT When the upper unit is raised, the pre-imprinter carriage moves to the ink cartridge replacement position. Therefore, the scanner must be ON when replacing the pre-imprinter ink cartridge. 1. Press the Open/Close button and carefully raise the upper unit until it stops
  • Canon DR-X10C | User Manual - Page 83
    seal covering the nozzles of a cartridge only if you are going to use it immediately. Also, avoid touching the metal contacts or nozzles of the ink cartridge. Chapter 5 Maintenance IMPORTANT • If the carriage is closed before the lock lever is raised, it will not be possible to turn the lock lever
  • Canon DR-X10C | User Manual - Page 84
    (Post-Imprinter) Replace the Post-imprinter ink cartridge using the following procedure. 1. Adjust the document feed guides outward to allow access to the imprinter cover. 2. Press the imprinter cover tab (indicated by the arrow in the illustration) to unlock it. Chapter 5 Maintenance 4.
  • Canon DR-X10C | User Manual - Page 85
    it immediately. Also, avoid touching the metal contacts or nozzles of the ink cartridge. Chapter 5 Maintenance 9. Carefully close the imprinter cover. 7. by the arrow in the illustration) to lock it. 8. Push the ink cartridge as indicated by the arrow until it clicks into place. IMPORTANT When
  • Canon DR-X10C | User Manual - Page 86
    . Chapter 5 Maintenance ■ Cleaning Out Excess Ink (Pre-Imprinter) When using the pre-imprinter, document pages are transported while the ink is still wet, so the platen roller and scanning glass will pick up ink, eventually resulting in streaks in images or soiled documents. Therefore, when using
  • Canon DR-X10C | User Manual - Page 87
    After replacing an ink cartridge or cleaning the print head, perform a test print to confirm proper printing. Test printing is performed by the "Imprinter Test" User Mode selection. IMPORTANT Before performing an Imprinter Test, load a sheet of paper into the Document Feed Tray. ■ Performing an
  • Canon DR-X10C | User Manual - Page 88
    Chapter 6 Practical Examples 1. Messages 6-2 Status Display 6-2 Error Messages 6-3 2. Troubleshooting 6-5 Trouble Categories 6-5 Problem and Solution 6-5 3. Uninstalling the Software 6-9 Uninstalling the ISIS/TWAIN Driver 6-9
  • Canon DR-X10C | User Manual - Page 89
    in Count-Only mode. ■ Insert the Sheet Status: In the Cleaning Mode, waiting for the cleaning sheet to be inserted. ■ Press Start Key Status: Waiting. Load a document and press the Start key. ■ Ready Status: The scanner is ready to use. Status: The scanner is entering the Sleep mode. Press any
  • Canon DR-X10C | User Manual - Page 90
    finishes, clean the scanning glass. ■ Call for Service Error Code: Exxx (excluding E021) Problem: Internal scanner error. Solution: Turn the power OFF, and restart the scanner. If this does not solve the problem, make a note of the error code, and contact your Canon service representative. 6-3
  • Canon DR-X10C | User Manual - Page 91
    the eject outlet, return them to the Document Feed Tray, and scan again. (See p. 3-22.) Error Code: E021 Problem: An error has occurred with the Document Feed Tray. Solution: Turn the power OFF, and restart the scanner. ■ Count Mismatch Error Code: U001 Problem: The specified count has not yet been
  • Canon DR-X10C | User Manual - Page 92
    • Documents Do Not Feed Properly (See p. 6-7) • Saved Image Files Do Not Open (See p. 6-7) • Scanning Results Are Not as Expected (See p. 6-7) It you cannot resolve a problem, contact your local authorized Canon dealer or your service representative. Problem and Solution ■ The Scanner Does Not
  • Canon DR-X10C | User Manual - Page 93
    and PC correctly connected with the proper cable? ✔ Is the scanner's power switch turned ON? If this does not solve the problem, consider the following possible causes: Cause Solution The ISIS/TWAIN driver and Job Registration Tool are not installed correctly Uninstall and then reinstall the
  • Canon DR-X10C | User Manual - Page 94
    is not improved after cleaning the rollers, contact your local Canon dealer or service representative to purchase a Roller Replacement Kit, and replace the rollers (pickup, feed and retard rollers). (See "Replacing the Transport Rollers" on p. 5-12.) If this does not solve the problem, consider the
  • Canon DR-X10C | User Manual - Page 95
    appear on the image even after you clean the scanning glass and rollers, the scanning glass inside the scanner may be scratched. Contact your local authorized Canon dealer or service representative. Problem Cause Solution The scanned image is abnormal for certain documents. A detection function
  • Canon DR-X10C | User Manual - Page 96
    Uninstalling the Software Some scanner malfunctions can be resolved by reinstalling the software. Before reinstalling the software, make sure to completely uninstall any previous installation first. Uninstalling the ISIS/TWAIN Driver The following procedure uses the ISIS/TWAIN driver as an example
  • Canon DR-X10C | User Manual - Page 97
    4. Click [Yes] to proceed with uninstallation. 5. When uninstallation is finished, click [Finish]. Chapter 6 Practical Examples 6-10
  • Canon DR-X10C | User Manual - Page 98
    Chapter 7 Appendix 1. Specifications 7-2 Unit Specifications 7-2 Options 7-4 Consummables 7-4 External Dimensions 7-5 2. Option Specifications 7-6 Barcode Specifications 7-6 Imprinter Specifications 7-7 3. Index 7-8
  • Canon DR-X10C | User Manual - Page 99
    Manual Document Page Count Up to 500 pages of good quality paper Scanning Sensor Contact image sensor Light Source LED Scanning Sides Simplex/Duplex Scanning Modes Black and White, Error Diffusion, Advanced Text Enhancement, Advanced Text Enhancement II, 256Level Grayscale, and 24-Bit Color
  • Canon DR-X10C | User Manual - Page 100
    46 pages/min. Duplex 46 images/min. Chapter 7 Appendix 600 dpi (image quality priority) Simplex 32 pages/min. Duplex 18 images/min. Other Double-Feed Detection function, Deskew, Selectable Background, Dust Countermeasures, Auto USB Power Switching, User Mode, Long Document Mode, and Folio Scan
  • Canon DR-X10C | User Manual - Page 101
    roller replacement kit, contact your local authorized Canon dealer or service representative. Cleaning Sheets (Product Code: 2418B002) This is a package of cleaning sheets for cleaning the transport rollers. (See "Cleaning Rollers with a Cleaning Sheet" on p. 5-4.) Ink Cartridge: Blue (Product Code
  • Canon DR-X10C | User Manual - Page 102
    External Dimensions Chapter 7 Appendix 20.79" (528 mm) 14.77" (375 mm) 17.01" (432 mm) 5.51" (140 mm) 22.17" (563 mm) 21.10" (536 mm) 33.90" (861 mm) 7-5
  • Canon DR-X10C | User Manual - Page 103
    Sheets (Option)" (p. 3-19) for the specifications of the patchcodes that can be detected by the patchcode decoder. Barcode Specifications The following barcodes can be read by installing the optional barcode module. ■ Barcode Types Code No. of Digits Checksum EAN Codabar Code 39 ITF Code
  • Canon DR-X10C | User Manual - Page 104
    coating Compatible Ink Cartridges HP Ink Cartridges Color: Blue, Red, Green (see p. 5-14) Image Density 12 nozzles/oblique line (96 dpi) Ink Type Water-based Operating Environment As specified for the ink cartridge Scanning Unit Printing Side Front Position Set in the ISIS/TWAIN driver (See p. 8-26
  • Canon DR-X10C | User Manual - Page 105
    5-9 rollers 5-3 scanner 5-2 Cleaning Cloth 5-2 Cleaning Mode 5-4 Cleaning Sheet 5-4 Connecting to a Computer 2-6 Control Panel 1-11 Counter 5-13 Count-Only Mode 4-4 D Daisy-Chain Configuration 2-8 Device Manager 2-10 Disposal 1-5 Document Eject Tray 3-11 extension 3-11 Document Feed
  • Canon DR-X10C | User Manual - Page 106
    Pre-Imprinter 4-8 Problems and Solutions 6-5 R Rapid Recovery System 3-23 Replacing the Ink Cartridge post-imprinter 5-17 pre-imprinter 5-15 Replacing the Transport Rollers 5-12 replacement cycle 5-12 Roller Replacement Kit 5-12 S Safety Instructions 1-2 Scanner Recognition 2-9 Scanning
  • Canon DR-X10C | User Manual - Page 107
    User Manual Software Please read this manual before using the scanner. After you finish reading this manual, keep it in a safe place for future reference.
  • Canon DR-X10C | User Manual - Page 108
    Table of Contents Chapter 8 ISIS/TWAIN Driver Settings 1. Before You Start Using the Scanner 8-2 2. ISIS/TWAIN Driver Settings Dialog Box ...........8-4 Basic Tab Sheet 8-5 [Brightness] Tab Sheet 8-12 [Image processing] Tab Sheet 8-15 [Others] Tab Sheet 8-17 [Pre Imprinter] and [Post Imprinter]
  • Canon DR-X10C | User Manual - Page 109
    Chapter 8 ISIS/TWAIN Driver Settings 1. Before You Start Using the Scanner 8-2 2. ISIS/TWAIN Driver Settings Dialog Box .......... 8-4 Basic Tab Sheet 8-5 [Brightness] Tab Sheet 8-12 [Image processing] Tab Sheet 8-15 [Others] Tab Sheet 8-17 [Pre Imprinter] and [Post Imprinter] Tab Sheets 8-24
  • Canon DR-X10C | User Manual - Page 110
    3.0] - [CapturePerfect 3.0]. 2. Select [Select Scanner] from the [Scan] menu. CapturePerfect 3.0 starts. The [Select Scanner] dialog box appears. 3. Select "CANON DR-X10C", and click [Settings]. IMPORTANT If [CANON DR-X10C] does not appear, try reinstalling the ISIS/ TWAIN driver. 8-2
  • Canon DR-X10C | User Manual - Page 111
    here. • For the TWAIN driver, the default paper size is LTR/A4 and cannot be changed. 5. Click [OK] to finish scanner selection. 6. From the [Scan] menu, select [Scanner Setting]. Hint For details on the ISIS Driver Settings dialog box, see "ISIS/ TWAIN Driver Settings Dialog Box" on p. 8-4. 8-3
  • Canon DR-X10C | User Manual - Page 112
    ]. See the description of each tab sheet for details. ISIS Driver Settings Dialog Box TWAIN Driver Settings Dialog Box • Basic Tab Sheet (See p. 8-5) • [Brightness] Tab Sheet (See p. 8-12) • [Image processing] Tab Sheet (See p. 8-15) • [Others] Tab Sheet (See p. 8-17) • [Pre Imprinter] and [Post
  • Canon DR-X10C | User Manual - Page 113
    ISIS driver only) This [Basic] tab sheet is displayed when the DR-X10C ISIS Driver is utilized from a scanner setting or scanning dialog box belonging to an ISIS-compatible application program. This tab sheet contains settings for DR-X10C functions that are not supported - [Auto Color Detection] ➔ [
  • Canon DR-X10C | User Manual - Page 114
    sheet. • If the background is non-uniform, such as a pattern, the background remains visible in the image, and text may be difficult to read. [256-level Gray] Scans documents, such as photos, as 256-level grayscale images. [24-bit Color] Scans documents, such as color photos, as full-color images
  • Canon DR-X10C | User Manual - Page 115
    8 ISIS/TWAIN Driver Settings [Auto Color Detection] The document is detected as black-and-white or color before the scanned image is saved. Selecting this mode enables the [Setting] button for opening the [Auto Image Type Detection Settings] dialog box, where you can make settings for auto image
  • Canon DR-X10C | User Manual - Page 116
    separation setting on the [Others] tab sheet is set to [Patchcode] (Optional). (See "Batch Separation" on p. 8-20.) Chapter 8 ISIS/TWAIN Driver Settings [Deskew] Check Box The Deskew function detects slanted document pages and straightens the scanned images. IMPORTANT The Deskew function does not
  • Canon DR-X10C | User Manual - Page 117
    to [24-bit Color], and the scanning side is [Duplex], the scanner may run out of memory and unable to scan the entire document. If this occurs, enable [Speed priority] and scan images of lower quality, or set the scanning side to [Simplex]. [Scan Options] (TWAIN driver only) Specify the operation
  • Canon DR-X10C | User Manual - Page 118
    mode. For details on the [Brightness] tab sheet settings, see "[Brightness] Tab Sheet" on p. 8-12. Basic Settings Tab Sheet Image processing Others Chapter 8 ISIS/TWAIN Driver Settings Prescan Batch Separation (ISIS driver) JPEG Transfer Color drop-out Prevent Bleed Through / Remove Background
  • Canon DR-X10C | User Manual - Page 119
    and register nonstandard document page sizes. The Scan Area dialog box is different for ISIS and TWAIN drivers: for the TWAIN driver, one of two dialog box types is displayed, depending on the application program used. Scan Area Dialog Box (ISIS Driver) Chapter 8 ISIS/TWAIN Driver Settings The Area
  • Canon DR-X10C | User Manual - Page 120
    [Basic] tab sheet (p. 8-5). Chapter 8 ISIS/TWAIN Driver Settings [Preview] Button (TWAIN driver only) Load the document and then click the [Preview] button to scan one document page and display its preview image in the Area panel. [Brightness] Tab Sheet On the [Brightness] tab sheet you can adjust
  • Canon DR-X10C | User Manual - Page 121
    mode is [Black and White]. The brightness and contrast are adjusted according to the document. Brightness Adjusts the brightness of images to be scanned. Hint • If images are too dark or if text on the back of a sheet bleeds through, you can drag the slider to the right to increase the setting
  • Canon DR-X10C | User Manual - Page 122
    Chapter 8 ISIS/TWAIN Driver Settings Input method Select the setting method for gamma correction. [Factor] Move the slider to the left or right to adjust the gamma correction factor between 0.2 and 5.0. Hint • The gamma correction value, Gamma Curve Graph, and sample image color
  • Canon DR-X10C | User Manual - Page 123
    the custom gamma curve settings as a gamma table file (*.pxg). Chapter 8 ISIS/TWAIN Driver Settings [Image processing] Tab Sheet The [Image processing] tab sheet provides settings affecting the processing of scanned images. Some settings may be disabled, depending on the mode settings on the [Basic
  • Canon DR-X10C | User Manual - Page 124
    Chapter 8 ISIS/TWAIN Driver Settings Document Orientation Specify a rotation angle to correct the orientation of images. Hint Scanned images are rotated as follows, according to the orientation of loaded documents and the selected angle. Feeder Document: Face Up Document Orientation (Clockwise)
  • Canon DR-X10C | User Manual - Page 125
    out or enhanced: that is, the colors you specify may not match those processed. Hint [Batch Separation] and [Patchcode Orientation] are functions for setting the ISIS driver, so they are not displayed for the TWAIN driver. ■ [Others] Tab Sheet Settings You can configure the following settings
  • Canon DR-X10C | User Manual - Page 126
    instructions from the ISIS/TWAIN driver or application program. - With uncompressed transfer, scanned image data is output without being compressed. Therefore, if the image data is large, transfer of the data from the scanner to the computer may take a long time. - JPEG transfer is useful for color
  • Canon DR-X10C | User Manual - Page 127
    scanning with an application program. Scanning stops when the loaded document has been scanned. Chapter 8 ISIS/TWAIN Driver Settings [Manual Feeding] (Bypass Mode) This is linked to the [Bypass Mode] key on the control panel. When [Manual Feeding] is selected, the [Bypass Mode] key is lit and the
  • Canon DR-X10C | User Manual - Page 128
    [Setting] Button This button is enabled when [Automatic Feeding] is selected, and allows you to set the delay time from when a loaded document is detected until scanning starts. Chapter 8 ISIS/TWAIN Driver Settings Batch Separation (when a patchcode decoder is installed) When the optional patchcode
  • Canon DR-X10C | User Manual - Page 129
    (ISIS driver only) This function is enabled when the optional patchcode decoder is installed and batch separation is set to [Patchcode]. Set the orientation to match that of the patchcode of the patchcode sheet. Hint Settings for various patchcode types and orientations on document pages
  • Canon DR-X10C | User Manual - Page 130
    to the feeding direction have 90-degree orientation, and detection is possible regardless of which end is the starting point. Chapter 8 ISIS/TWAIN Driver Settings Search Area [Enable] check box Select this check box to limit barcode detection to within a specified area of the document, and then
  • Canon DR-X10C | User Manual - Page 131
    Chapter 8 ISIS/TWAIN Driver Settings Code 39 Detect Code 39 barcodes. [Enable] Detect and read Code 39 barcodes. [Full Ascii] Read barcodes in Full ASCII Code. [Checksum] Read the checksum included in barcodes. [Output Checksum] This check box is enabled when [Checksum] is selected, and outputs the
  • Canon DR-X10C | User Manual - Page 132
    UPC-A/UPC-E barcodes. Chapter 8 ISIS/TWAIN Driver Settings [Pre Imprinter] and [Post Imprinter] Tab Sheets The [Pre Imprinter] tab sheet is displayed when an optional pre-imprinter unit is installed, and allows you to imprint any character string or counter on to documents before scanning. [Enable
  • Canon DR-X10C | User Manual - Page 133
    documents. IMPORTANT • Confirm that an ink cartridge is installed in the scanner before you use the imprinter function. "ImprinterError" is displayed on the scanner LCD if scanning is performed without the ink cartridge. • Pre-imprinter printing is only available when the scanner's Double-Feed
  • Canon DR-X10C | User Manual - Page 134
    ISIS/TWAIN Driver Settings [Double counter with number of characters] abbreviation: A dialog box appears in which to specify the number of characters of the double counter. A counter of the specified number of characters will be imprinted or added on scanned images with the ink outlet. •
  • Canon DR-X10C | User Manual - Page 135
    8 ISIS/TWAIN Driver Settings Orientation Specify the orientation of characters to be imprinted or added. Hint Text orientation relative to the feeding direction . Addon Type Specify the method in which text is added on to the image. [Black on White] Add black text on to a white background. First
  • Canon DR-X10C | User Manual - Page 136
    to the Batch Separation settings on the [Others] tab sheet. (See "Batch Separation" on p. 8-20.) IMPORTANT The counter for the imprinter does not increase when [Patch code] is selected for [Batch Separation]. Chapter 8 ISIS/TWAIN Driver Settings [Every Page] Increments once per page. [None] No
  • Canon DR-X10C | User Manual - Page 137
    Chapter 9 Job Registration Tool Settings 1. Before Use 9-2 Job Function 9-2 Starting the Job Registration Tool 9-2 2. Job Registration Tool 9-3 3. Settings Dialog Boxes 9-5 [New/Editing] Dialog Box 9-5 [Admin] Dialog Box 9-8
  • Canon DR-X10C | User Manual - Page 138
    scanning application. Hint • Job registration stores scanning condition settings, image file format selection, save destination and image data processing settings for each job to be used with the Job the [Start] button, and then click [All Programs] - [Canon DR-X10C] - [Job Registration Tool]. 9-2
  • Canon DR-X10C | User Manual - Page 139
    Job Registration Tool The Job Registration Tool consists of the main window below and the [New/Editing] and [Admin] dialog boxes. Menu Open the [Admin] dialog box to configure settings for monitoring the storage folder for images and backing up job data. (See "[Admin] Dialog Box" on p. 9-8.) [Help]
  • Canon DR-X10C | User Manual - Page 140
    Job List Displays the job numbers (01 to 99) and job titles. Job Information Displays the information for the job selected in the job list. [Close] Button Ends the Job Registration Tool. Chapter 9 Job Registration Tool Settings 9-4
  • Canon DR-X10C | User Manual - Page 141
    Chapter 9 Job Registration Tool Settings 3. Settings Dialog Boxes The settings dialog boxes of the Job Registration Tool include the [New/Editing] dialog box and [Admin] dialog box. For details, see the description of each dialog box. [New/Editing] Dialog Box In the [New/Editing] dialog box, you
  • Canon DR-X10C | User Manual - Page 142
    to save image files to the My Pictures folder of the user logged in to Windows. Hint • images. When scanning multi-page documents, image files are created as follows according to the selected file format: PDF: All pages are saved in a single image file. BMP: Each page is saved in a separate image
  • Canon DR-X10C | User Manual - Page 143
    rate setting is enabled when the scanner is set to [256-level Gray] or [24-bit Color] mode. When [Black and White] or [Error Diffusion] binary image scanning mode is selected, file size depends on the content of the scanned document. Language for OCR When the [Apply OCR] check box is selected, the
  • Canon DR-X10C | User Manual - Page 144
    format for saving grayscale and color images. When the [Compression] check box is selected, a standard level of JPEG compression is applied. IMPORTANT If your application program does not support the above compression formats, you may be unable to open scanned image files. In this case disable
  • Canon DR-X10C | User Manual - Page 145
    the specified limit. • If a warning message appears, follow the instructions in the message to either continue scanning or change the save destination a different environment, such as occurs when multiple users log on to Windows or when multiple DR-X10C scanners are used. [Back Up] Button Writes a
  • Canon DR-X10C | User Manual - Page 146
    1. About Basic Condition Settings 10-2 Confirming the Basic Conditions for Scanning....10-2 2. Practical Examples 10-4 Scanning Documents of Unregistered Page Sizes 10-4 Specifying the Scanning Area 10-5 Configuring Scanner Settings According to the Purpose 10-6 Registering Your Settings 10-11
  • Canon DR-X10C | User Manual - Page 147
    setting items that are the minimum requirements when configuring the scanner settings. For details on settings, see Chapter 8 "ISIS/TWAIN Driver Settings Dialog Box". Confirming the Basic Conditions for Scanning When you scan a document, be sure to confirm the basic conditions [Mode], [Page Size
  • Canon DR-X10C | User Manual - Page 148
    which page side(s) to scan. Hint • If the scanning side is set to [Skip Blank Page], the images of blank pages are deleted when the images are saved. • [Folio] recombines the front and back images scanned from both sides of the document into a single image. Chapter 10 Practical Examples 10-3
  • Canon DR-X10C | User Manual - Page 149
    using black and white or reducing the image quality. • When scanning with the Long Document Mode set to [ON2], if the scan is performed at 400/600 dpi or the scan is performed with the scanning mode set to color and the scanning side set to [Duplex], the image may be lost. If this occurs
  • Canon DR-X10C | User Manual - Page 150
    , which is opened from the [Area] button on the [Basic] tab sheet. (See p. 8-11.) Front Back Bypass Mode Key Reconstructed Image Specifying the Scanning Area Configure the following settings when you want to specify the area of the document to scan. ■ Specifying an area Specify the area of the
  • Canon DR-X10C | User Manual - Page 151
    blue, or green) to be ignored (dropped out) in [Color drop-out] on the [Image processing] tab sheet, and that color will be not be scanned. (See p. 8-17.) • With CapturePerfect 3.0, the last scanned image appears in the preview window. Scan the document you want to set the area of with [Scan Single
  • Canon DR-X10C | User Manual - Page 152
    ■ When you want to skip or enhance intermediate colors Select an intermediate color in [Color drop-out] on the [Image processing] tab sheet. The Color Settings dialog box is displayed, and you can specify the color range of the intermediate colors to ignore (drop out) or enhance. Chapter 10
  • Canon DR-X10C | User Manual - Page 153
    is set to white, [Border Removal] is disabled. ■ When you want to reduce the moire patterns that appear when color photos in magazines and other documents are scanned at low resolutions Setting [Moire Reduction] on the [Basic] tab sheet allows you to reduce the moire patterns that are generated when
  • Canon DR-X10C | User Manual - Page 154
    tab sheet, the document colors are detected and black and white images and color images are saved separately. (See p. 8-6.) Chapter 10 Practical Examples ■ When you want to reverse black and white in scanned images (TWAIN driver only) Select [Reverse Image] on the [Image processing] tab sheet. This
  • Canon DR-X10C | User Manual - Page 155
    want to remove the black spots from scanned images when scanning documents with punch holes (when the background is set to black) When the background color is set to black on the [Others] tab sheet, select [Punch Hole Removal] on the [Image processing] tab sheet. The black spots from punch holes in
  • Canon DR-X10C | User Manual - Page 156
    If you set the scanning side setting to [Skip Blank Page] on the [Basic] tab sheet, the images of blank pages in the document are deleted. (See p. 8-7.) Chapter 10 Practical Examples Registering Your Settings You can register the scanning conditions so that you can use them next time. ■ Registering
  • Canon DR-X10C | User Manual - Page 157
    INC. 1248, SHIMOKAGEMORI, CHICHIBU-SHI, SAITAMA 369-1892, JAPAN CANON U.S.A. INC. ONE CANON PLAZA, LAKE SUCCESS, N.Y. 11042, U.S.A. CANON CANADA INC. 6390 DIXIE ROAD, MISSISSAUGA, ONTARIO L5T 1P7, CANADA CANON EUROPA N.V. BOVENKERKERWEG 59-61, P.O.BOX 2262, 1180 EG AMSTELVEEN, THE NETHERLANDS
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
Please read this manual before using the scanner.
After you finish reading this manual, keep it in a safe place
for future reference.
User Manual