Canon MultiPASS F30 F30 Setup

Canon MultiPASS F30 Manual

Get Canon MultiPASS F30 PDF manuals and user guides View all Canon MultiPASS F30 manuals
Add to My Manuals
Save this manual to your list of manuals

Canon MultiPASS F30 manual content summary:

  • Canon MultiPASS F30 | F30 Setup - Page 1
    Step 1: Unpack the F30 MFP 1. Carefully remove all items from the box. Step 2: Set up the F30 MFP 1. Remove shipping tape and protective shipping materials.
  • Canon MultiPASS F30 | F30 Setup - Page 2
    2. Open the scanning unit by pressing the Open button. Remove the shipping material. 3. Unlock the scanner. • Set the scanning lock to unlock. • Press the scanning unit closed until it clicks. 4. Attach the trays:
  • Canon MultiPASS F30 | F30 Setup - Page 3
    2. If the F30 MFP does not power up when plugged in, press the ON/OFF button to turn it on. 3. Open the scanning unit again. The printhead holder will move to the center position. IMPORTANT: Remove the tape on the printhead holder lever. Step 4: Install the Printhead 1. Remove the printhead from its
  • Canon MultiPASS F30 | F30 Setup - Page 4
    over, then remove the orange protective cap. NOTE: Do not touch the electrical contacts. 3. Raise the gray lock lever. 4. Gently slide the printhead into the holder. The printhead will rest at a slight angle. Do not press it down. 5. Lower the lock lever and gently press it down until it locks into
  • Canon MultiPASS F30 | F30 Setup - Page 5
    (refer to the color guide on the printhead). Press down gently until the ink tank locks into place. 4. Insert the remaining three ink tanks into their assigned slots. 5. Press the scanning unit closed until it clicks. Step 6: Align the Printhead 1. Place a stack of paper in the multi-purpose tray
  • Canon MultiPASS F30 | F30 Setup - Page 6
    2. Once the printhead has been installed ALIGN PRINTHEAD/PRESS SET KEY will display on the LCD panel. Press the key once. 3. The F30 MFP will print a vertical line pattern, and the LCD message will change to:. 4. Review the vertical pattern printout, noting which box in Column A prints with the most
  • Canon MultiPASS F30 | F30 Setup - Page 7
    7 for Column H on the printout. 9. When printhead alignment is complete, the F30 MFP will return to standby mode. Step 7: Install the Software (USB cable only) NOTE: Windows 98, Me and 2000 only support the use of a USB cable. IMPORTANT: DO NOT connect he F30 MFP to your computer until prompted, or
  • Canon MultiPASS F30 | F30 Setup - Page 8
    YES. If you do not agree, click NO. You will not be allowed to continue the installation process. 7. Select the MultiPASS F30 for installation. Continue to follow the on-screen instructions. 8. When prompted, connect one end of the USB cable (not included) to the computer and the other end to the
  • Canon MultiPASS F30 | F30 Setup - Page 9
    manually. NOTE: Remember to register your product to ensure product support. The serial number is located on the back of the F30 MFP, above the parallel port. Step 7: Install the Software (Parallel cable only) NOTE: Windows 95, 98, Me, NT 4.0 and 2000 support the use of an IEEE 1284 parallel printer
  • Canon MultiPASS F30 | F30 Setup - Page 10
    process. 8. Select the MultiPASS F30 for installation. Continue to follow the on-screen instructions. 9. When installation is complete, you will need to restart your PC before using the MultiPASS Suite software. If your PC does not restart automatically, restart it manually. NOTE: Remember to
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
Step 1: Unpack the F30 MFP
1. Carefully remove all items from the box.
Step 2: Set up the F30 MFP
1. Remove shipping tape and protective shipping materials.