Canon PIXMA MX712 Guide for Printer Setup for Network

Canon PIXMA MX712 Manual

Get Canon PIXMA MX712 PDF manuals and user guides View all Canon PIXMA MX712 manuals
Add to My Manuals
Save this manual to your list of manuals

Canon PIXMA MX712 manual content summary:

  • Canon PIXMA MX712 | Guide for Printer Setup for Network - Page 1
    Network Connection Wireless Connection Preparation for Connection Printer Setup Setup Procedure Selection Push Button Method Standard setup WPS Other setup (Advanced setup) Disable WEP WPA/WPA2 Wired Connection Preparation for Connection Cable Connection Printer Setup Character Entry Troubleshooting
  • Canon PIXMA MX712 | Guide for Printer Setup for Network - Page 2
    Setup 1. Make sure that the printer is turned on. If the power manual of your network device or contact its manufacturer. • Check if your device supports IEEE802.11n, 802.11g or 802.11b. • If your device is set to the "IEEE802.11 n only" mode, WEP or TKIP cannot be used as a security protocol. Change
  • Canon PIXMA MX712 | Guide for Printer Setup for Network - Page 3
    ) Wi-Fi lamp (C) lights up when wireless connection is enabled. c Setup Procedure Selection The printer will automatically search for access points supporting WPS (Wi-Fi Protected Setup). If the Push Button Method screen is displayed on the printer but you are unsure if your access point or router
  • Canon PIXMA MX712 | Guide for Printer Setup for Network - Page 4
    point (for about 5 seconds). For details on pressing the WPS button, refer to the access point manual. 2. Press the OK button on the printer within 2 minutes. The (blue) Wi-Fi lamp on the printer flashes while searching for or connecting to the access point. 3. When the left screen appears, press
  • Canon PIXMA MX712 | Guide for Printer Setup for Network - Page 5
    d Connection via Standard setup 1. Select Standard setup. 2. Press the OK button. 3. Select your access point, then press the OK button. 4. One of the screens above will be displayed on the printer. 5. Press the OK button. 6. Enter the network password (WEP key or passphrase) of your access point
  • Canon PIXMA MX712 | Guide for Printer Setup for Network - Page 6
    point (for about 5 seconds). For details on pressing the WPS button, refer to the access point manual. 7. Press the OK button on the printer within 2 minutes. The (blue) Wi-Fi lamp on the printer flashes while searching for or connecting to the access point. 8. When the left screen appears, press
  • Canon PIXMA MX712 | Guide for Printer Setup for Network - Page 7
    . 6. Select a security protocol for the access point, then press the OK button.  Disable 7. When the left screen appears, press the OK button. The network connection setup is now complete.  WEP 7. Select the WEP key number you want to use. 8. Press the OK button.
  • Canon PIXMA MX712 | Guide for Printer Setup for Network - Page 8
    that the WEP key is correct. 13.Press the left Function button. 14.When the left screen appears, press the OK button. The network connection setup is now complete.  WPA/WPA2 7. Press the OK button. 8. Enter the passphrase of your access point or router. 9. Press the left Function button. 10.Make
  • Canon PIXMA MX712 | Guide for Printer Setup for Network - Page 9
    12.When the left screen appears, press the OK button. The network connection setup is now complete.
  • Canon PIXMA MX712 | Guide for Printer Setup for Network - Page 10
    for Connection Before Starting Wired Connection Setup 1. Make sure that the printer is turned on. If the power is on, the lamp on one , connect the printer and computer to the LAN side (same network segment). b Cable Connection You will need an Ethernet cable (sold separately). 1. Remove the Cap (A)
  • Canon PIXMA MX712 | Guide for Printer Setup for Network - Page 11
    1. Press the MENU button (A) on the printer. 2. Use the buttons (A) to select the Setup icon. 3. Press the OK button (B). 4. Select Device settings. 5. Press the OK button. 6. Select LAN settings. 7. Press the OK button. 8. Select Change wireless/wired. 9. Press the OK button. 10.Select
  • Canon PIXMA MX712 | Guide for Printer Setup for Network - Page 12
    12.Press the MENU button. The network connection setup is now complete.
  • Canon PIXMA MX712 | Guide for Printer Setup for Network - Page 13
    You can enter the characters when the keyboard is displayed on the printer. Follow the procedure below. 1. When an on-screen keyboard shown above is displayed, press the center Function button (A) to switch to a keyboard that supports characters you want to use. Three types of keyboard (upper case
  • Canon PIXMA MX712 | Guide for Printer Setup for Network - Page 14
    configure wireless connection settings again. "WPA/WPA2 Enterprise" is not supported on this printer. For details on how to change the security protocol (encryption standard) for the access point, refer to the manual supplied with the access point or contact its manufacturer.  Multiple access points
  • Canon PIXMA MX712 | Guide for Printer Setup for Network - Page 15
    function of the access point is inactive, enable the DHCP function and configure wireless connection settings again. For details on how to check or change the settings of the access point, refer to the manual supplied with the access point or contact its manufacturer.
  • Canon PIXMA MX712 | Guide for Printer Setup for Network - Page 16
    a WEP key number by entering wireless connection settings of the printer directly. For details on how to change the WEP key number of the access point, refer to the manual supplied with the access point or contact its manufacturer. If the problem is not resolved, there may be other causes. See also
  • Canon PIXMA MX712 | Guide for Printer Setup for Network - Page 17
    > WLAN setting list to check MAC address. For details on how to change the settings of the access point, refer to the manual supplied with the access point or contact its manufacturer.  To perform Standard setup again 1. Press the MENU button (A). 2. Use the buttons (B) to select Wireless LAN
  • Canon PIXMA MX712 | Guide for Printer Setup for Network - Page 18
    For details on how to check the settings of the access point, refer to the manual supplied with the access point or contact its manufacturer.  Timeout error. Check the access point. See the access point manual. The screen appears when WPS setup was not completed within a specified time. Complete the
  • Canon PIXMA MX712 | Guide for Printer Setup for Network - Page 19
    configure wireless connection settings again. "WPA/WPA2 Enterprise" is not supported on this printer. For details on how to change the security protocol (encryption standard) for the access point, refer to the manual supplied with the access point or contact its manufacturer.  Multiple access points
  • Canon PIXMA MX712 | Guide for Printer Setup for Network - Page 20
    Confirm LAN settings > WLAN setting list to check MAC address. For details on how to change the settings of the access point, refer to the manual supplied with the access point or contact its manufacturer. If the problem is not resolved, there may be other causes. See also the sections below: If the
  • Canon PIXMA MX712 | Guide for Printer Setup for Network - Page 21
    a WEP key number by entering wireless connection settings of the printer directly. For details on how to change the WEP key number of the access point, refer to the manual supplied with the access point or contact its manufacturer. If the problem is not resolved, there may be other causes. See also
  • Canon PIXMA MX712 | Guide for Printer Setup for Network - Page 22
    For details on how to check or change the settings of the access point, refer to the manual supplied with the access point or contact its manufacturer. To specify the IP address of the printer, follow the procedure below. 1. Press the MENU button. 2. Select Setup, then press the OK button. 3. Select
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
Setup Guide
This guide provides information for setting up a network connection for the printer.
Network Connection
Wireless Connection
Preparation for Connection
Printer Setup
Setup Procedure Selection
Push Button Method
Standard setup
WPS
Other setup (Advanced setup)
Disable
WEP
WPA/WPA2
Wired Connection
Preparation for Connection
Cable Connection
Printer Setup
Character Entry
Troubleshooting