Canon VB-R12VE Network Camera VB-R13VE/VB-R12VE/VB-R11VE/VB-R10VE Installation

Network Camera

/

/

/

Installation Guide

Please be sure to read the “Safety Precautions” section for correct use. After reading this Installation

Guide, keep it in a readily accessible location for future reference.

* Some cameras are not available in certain countries or regions.

Caution

Request a professional installer for all installation work. Never try to install the camera yourself.

Doing so may result in unforeseen accidents such as dropping the camera or electric shock.

Check Included Items

Camera

Installation Guide (This document)

Setup CD-ROM

Warranty Card

Dedicated wrench

Power Interface Cable

I/O Interface Cable (BK2-0035-000)

Power Interface Cable (Waterproof)

LAN Connector Set (Waterproof)

Waterproofing Tape

Waterproofing explanation sheet

Symbols Indicating Camera Model

Camera specific functions will be listed using the symbols below.

: VB-R13VE

: VB-R12VE

: VB-R11VE

: VB-R10VE

BIE-7184-000

© CANON INC. 2017

Printed in Japan

Before Installing the Camera

Set the IP address and other network information on the camera using the “Camera Management Tool” on the

Setup CD-ROM. For details on how to operate the “Camera Management Tool”, please refer to the

“Camera

Management Tool User Manual”.

Separating the Camera and Attachment

Note

Please unhook the safety

wire connected to the

camera.

❶

❷

❸

Removing and Attaching the Dome Case

Attaching the Dome Case

(1) Fix the screws in the dome case and

attach the safety wire.

(2) Align the dome case with the camera

body.

(3) Tighten the

dome case

screws with

the dedicated

wrench.

Removing the Dome Case

Loosen the screws holding the dome case in place with the

dedicated wrench, and remove it. Loosen the screws on the dome

case to detach the safety wire.

Dedicated

wrench

ENGLISH

Accessories

The following accessories can be purchased separately as necessary. Some accessories are not available in

certain countries or regions.

Ceiling Mounting Kit CM10-VB

Dedicated accessory for attaching the camera to the ceiling.

Wall Mounting kit WM10-VB

Dedicated accessory for attaching the camera to a wall surface.

1.5inch Pipe Adapter PA10-15-VB

Dedicated accessory used to install the camera to the end of pipe that extends from high ceilings, such as in big-box

stores.

Dome Unit DU10-S-VB

Smoked dome cover.

Canon AC Adapter PA-V18

Dedicated AC adapter for this camera.

Using a Memory Card

Remove the dome case and place the memory card in the memory card

slot.

To remove the memory card, push it in all the way until the card slightly

pops out and remove.

Important

• Insert a memory card before installing the camera.

• When using a memory card with the camera for the first time, it is

recommended to format the card after inserting it into the camera (please refer

to the “Operation Guide”).

• Always unmount the memory card before removing it (please refer to the

“Operation Guide”).

Memory card slot

Using the Dome Unit (sold separately)

Remove the dome case from the camera, then remove the dome cover holder and dome flange, and replace with

the smoked dome.

Dome flange

Dome cover

Rubber seal

Dome cover holder

Dedicated wrench

Smoked dome cover

Important

• Take care when replacing so as not to scratch the

dome cover.

• For proper protection against water and dust,

please make sure the screws are firmly tightened

during installation.

Connecting the LAN Connector Set (Waterproof)

Connect the LAN cable to the connector.

7.5 - 8.6 mm

6.1 - 7.5 mm

4.9 - 6.1 mm

14 - 16 mm

24 - 26 mm

❶

❷

❹

❺

❻

❼

❽

❾

❸

Note

• Align the wires with

the terminal settings

according to the

568B/568A color coded

illustration, and insert

them into the wire

manager.

• The LAN cable may not

be able to be properly

inserted or removed

from the LAN connector,

if the LAN Connector

Set (Waterproof) is not

used. The cable’s water

resistance will not be

maintained as well.

(

0.30 - 0.34 in.)

(0.55 - 0.63 in.)

(0.94 - 1.02 in.)

(

0.24 - 0.30 in.)

(

0.19 - 0.24 in.)

Wire Manager

568A

568B

Part Names

7

1

6

8

2

3

4

5

9

11

10

12

13

14 15

Serial_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

MAC_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

1. Power connection terminal

/ 2. External device I/O terminals

/

3. Audio input terminal (Black) (common LINE IN and MIC IN)

/

4. Audio output terminal (White) (LINE OUT)

/ 5. 100Base-TX LAN connector

/

6. Attachment screws / 7. Power connection terminal

/ 8. LAN connector

/

9. Dome case / 10. Reset switch / 11. Reboot switch / 12. Lens / 13. LED (Orange) / 14. Memory card slot /

15. LED (Blue)*

* On: when powered on, during reboot / Off: during normal use

a.

Box unit

Installing the Camera

1

Attached to ceilings/Attached to walls

The camera is installed with the Ceiling Mounting Kit (sold separately) or Wall Mounting kit (sold separately).

Please refer to the installation guide included with the Ceiling Mounting Kit and Wall Mounting kit for further details.

1 -2

1 -3

a

a

Ceiling Installation

Wall Installation

1 -1

Ceiling pendant mounting

Mount using the 1.5inch Pipe Adapter (sold separately).

For details please refer to the Installation Guide included with the

kit.

1 -1

Pass necessary cables

for connecting the camera

through the pipe.

Greater than 30 mm (1.2 in.)

1 -2

❶

❷

❸

M3

Included with 1.5inch

Pipe Adapter

2

2 -1

b

b

❶

❶

❷

❷

❸

❸

Dedicated wrench

Dedicated

wrench

b.

Joint unit

2 -2

c

c

❶

❶

❷

❷

c.

Shaft

2 -3



e

f

f

e

Note

Completely wrap the cable

connection with waterproof tape

to the cable jacket, so as not to

allow water to enter between the

individual cables.

e.

I/O interface cable

f.

Power interface cable

2 -4



g

g

❶

❷

❸

Dedicated

wrench

g.

TORX T30 driver

2 -1

c

d

d

b

b

c

❶

❶

❷

❷

b.

Joint unit

c.

Shaft

d.

LAN cable

2 -2

d

Note

Cut off the cap if the power interface

cable (Waterproof) is to be used.

Keep the cut-off cap in a safe

location. If the cap is not attached

when the power interface cable

(Waterproof) is not being used, it

may result in the accumulation of

water, which will damage the camera

body.

Using the Power Interface Cable (Waterproof)

2 -3

❶

❷

❸

To

3

for ceiling pendant

mounting

Dedicated wrench

2 -4


g

g

g.

TORX T30 driver

3

4

❶

❷

5

❶

❷

6

Dedicated

wrench

7

Canon VB-R12VE Network Camera VB-R13VE/VB-R12VE/VB-R11VE/VB-R10VE Installation

Canon VB-R12VE Manual

Canon VB-R12VE manual content summary: